Advanced Bluetooth Wireless Product BT- 2 0 2
Contents Introduction 1 Feature List 3 Safety and General Information 4 Before Using 6 Package contents 6 Turning the unit on/off 7 Installing the unit in a vehicle 8 Location of Controls 9 Function Operations 11 Pairing 11 Adjusting sp eaker vo lum e 13 Adjusting ring er volume 15 Back up SIM 16 Ⅰ
Troubleshooting Symptom Nothing appears on LCD display Check&Remedy l l l No op eration l l No LED ind icator Cannot wo rk 31 l l l Check that the LCD display is connected to b ase unit properly. Check that the b ase unit is connected to cig arette lig hter properly. Check that the base unit is connected to cig arette lig hter properly. Check that the base unit is turned on. Check the pairing is successful. Check that the b ase unit is connected to cig arette lig hter properly.
Introduction Care and M aintenance Your Bluetooth wireless product BT-202 Your advanced BT-202 is a product of superior design and should b e treated with care. The suggestions below will help you to enjoy your product for many years. The Bluetooth wireless p rod uct BT-202 is developed fo r installation in motor vehicles to enble hand sfree op eration o f your mobile phone. It is b ase on Bluetooth wireless technolog y connects to a comp atib le phone without wires.
Introduction Status Indicators What is Bluetooth wireless technology(continued) Status Indicators Bluetooth wireless product BT-202 c an connect to other Bluetooth devices within a rang e of approximate 1 0 metres. Pairing mode Standby mode Th e Blue LED flashes p er 3 seconds. Turn o n /off the unit by pressing MFB The Blue LED flashes 4 times rapidly. Power up the unit In talk m o d e 29 Th e Red LED and Blue LED flash alternately.
Feature List Caller ID System Operations 1. Bluetooth compatible Transferring a call ( continued) 2. Up to 10 me tre s range 3. To transfer back, just press MFB once. 3. LCD displays calling numbers 4. Talk time display 5. Full duplex 6.Easy installation 7. Speaker and ringer volume adjustment 8. Call back function 9. Voice dialling function To transfer a c all fro m m o b i l e p hone to the unit 1. When a call is received, press the reception button in your mobile phone to answer the call. 2.
Caller ID System Operations Safety and General Information Calling back the last 5 incoming numbers Important information on safe and efficient operation. Read this information before using your device. 1. In Standby mode, press Volume Up o r Volume Down button repeatedly t o select the number you want to call back. Users are not permitted to make chang es o r mod ify the d evice in any way.
Safety and General Information Caller ID System Operations M edical devices Hearing aid s Some devices may interfere with some hearing aids. In the event of such interference, you may want to consult with your hearing aid manufacturer to discuss alternatives. Other med ic al d evic es If you use any other personal med ical d evice, consult the manufacturer of your d evice to d etermine if it is ad eq uately shielded fro m RF energy.
Caller ID System Operations Before Using When a call is received , the LCD d isp lay shows caller's number, i f your local telep hone comp any p rovid es the Caller ID service. If the incoming numb er is stored in the p honeb ook, the matching name will display instead of the numb er when it is received . The last 5 incoming numb ers will be saved in the Caller ID list, and you can use the list to dial the numb ers. If the storag e is full, the old est number will b e rep laced b y the new one.
Before Using Function Operations Turning the unit on/off Rejecting a call When yo u turn on the ig nition of your car, the unit is turned on automatically. Then the Red and Blue LEDs flash alternately once and then the B l u e L E D fl as h es 2 0 t im es rap id ly, meanwhile "Welcome to BT202 " will show on the LCD display. After that, th e Blue LED flashes p er 3 second s, and the LCD display shows th e icon " VOL ". Then unit enters Standby mod e and is ready fo r use.
Function Operations Before Using Ending a call Installing the unit in a vehicle Press MFB once. OR End call from your mobile phone's keypad. After ending the call, the LC D will display the talk duration. Press this b utton once. figure A Call 1 VOl End talked 05:30 Last number redial In Standby mode, press and hold Volume Up or Volume Down button until you hear a prompt tone. After the tone, the last dialled number will be dialled out automatically.
Location of Controls Function Operations Base unit Answering a call When a call is received, the unit rings and the LCD display shows the caller's number. If the incoming number is stored in the phonebook, th e matching name will display instead of the numb er when it is received. Adjuster Speaker Press MFB to answer the call. OR Answer the call with your mobile phone's keypad.
Function Operations Location of Controls Making a call Display unit Using y ourm o b ile p hone 1 . I n Standby mode, dial the number by keypad. 2. Press mobile phone's "send" key. Using th e unit's voice-dialling (if supported by your mobile p hone) 1. In Standby mode, press MFB . 2. Yo u w i l l t h e n h e a r t h e v o i c e activation tone and your mobile will remind you to speak the voice tag.
Function Operations Function Operations Pairing Language setting You r BT-202 can store p airing information fo r up to five d ifferent devices equipped with Bluetooth wireless technology. When an attemp t to pair to more than five d evices is made, the oldest p aired device is removed from them em o ry. Yo u can select a display lang uag e. 4 d ifferent lang uag es are availab le. They ar e Germ an , En g l ish , Sp an ish an d French.
Function Operations Function Operations Deleting the phonebook number Pairing( continued) You c a n d elete t h e n u m b er in the p honeb ook. 1. Press and hold MFB until a prompt tone is heard to indicate the unit is turned off. ( When the unit is in Standby mode.) 1. P re ss b o th "Ba ck u p S I M " and "Download to SIM " button on the rear of the display unit once. The LCD will show "Del phonebook?" 2. Press the "Download to SIM " button to confirm.
Function Operations Function Operations Pairing(continued) Note: Function match. Then theOperations phone will remind you l Note: l After the unit enters p airing mode, i f there is no d evice linked within 2 minutes, the unit will return t o Standby mode. to enter passkey. The default passkey is " 0000 ". Please refer to the user's manual of your mobile phone for "pairing process". VOl l If the pairing is successful, the LCD display shows "VO L " and the unit enters Stand b y m o d e.
Function Operations Function Operations Download to SI M Adjusting speaker volume(continued) You can cop y the numb er from the unit to th e SIM card . 2 . P r e s s Vo l u m e D o w n b u t t o n t o O R Use the volume down switch of your mobile phone to decrease speaker d e c r e a se s p e a k e r vo l um e . S e e figure 2. volume (depending on your mobile phone) . 1. Insert a SIM card into the SIM card jack. 2. Press "Download to SIM " button on the rear of the display unit.
Function Operations Function Operations Adjusting ringer volume Note: l When yo u use Volume Up or Volume Down b utton o f the unit to ad justment the ringer volume, your mob ile phone's ring er volume may be ad justed accord ing ly(d ep end ing on your mobile phone). When a call i s received , the unit ring s. At the moment yo u c an press Volume U p or Volume Down button o r use yo ur mobile p hone(d ep end s on your mobile p hone) to adjust th e ringer volume. There are 5 levels for ad justing .
