Pro Series Digital SLR Auto-Focus TTL Flash w/LCD Display wide angle bounce diffuser & adapter Item # XT700EX INSTRUCTION MANUAL designed for Canon
Features High GN: 68 Wireless trigger sensor Recycle time 4 seconds (with 4 pcs AA alkaline cell) Compatible with E-TTL flash automatically Support Multi-flash lighting Appliction (s1/s2 mode) Power saving mode Accurate brightness control LCD display Metal hot shoe Support front curtain synchronous Support rear-curtain synchronous Temperature detection Automatically (overheating protection) Memory function -1-
Components 1. Reflector panel 2 1 2. Wide-angle diffuser 3 3. Flash head 4. Wireless trigger sensor 5. Battery cover 5 6. Hot Shoe 4 7. Locking ring 8. Hot shoe pin 6 9.
Components 10. LCD display 11. Mode switch button 12. Charging indicator 13. Test button 10 14. Zoom button 13 15.Power ON/OFF 11 16. Adjustment button 17.
Installation 1. Insert batteries Slide the battery compartment cover in the direction of the arrow to open it. Insert the batteries follow the direction inside the battery compartment cover, Make sure to place the positive and negative of the batteries correctly. c. Slide the battery compartment cover in the direction of the arrow to close it. a. b. a c b 1 2 2 1 Note: Please use 4 pcs standard AA batteries.Please don't use damage batteries, so as to avoid short circuit.
Installation 2. Install the speedlite on the camera. a. Rotate the locking ring in the direction of the arrow to the hightest point. b. Mount the speedlight into the camera`s hot shoe completely. c. Turn the locking ring in the direction of the arrow tighten,if you detach the speedlight, loosen the locking ring to the top, then remove the flashlight from camera`s hot shoe.
Status of charging indicator Test status of charging indicator after turn on the speedlite. Status of charging indicator Meaning Operation The red light is lit Charging Normal The green light is lit The batteries are full Normal Green blink The speedlite is locked because of the frequent flash,overheating protection.
Basic functions 1.Basic Operations Operation of the buttons: Components Operation The power of flashlight can be opened or closed by holding this button for 2 seconds. Press once, the mode will change among the TTL/M/ and button /S1/S2. Press this button to adjust the output power of the speedlite. button Press this button and the up and down keys to adjust the focal range of the speedlite.
Basic functions 2.Turn on/ off the speedlite 2.1 Turn on the speedlite sing ON/OFF button 2 seconds, LCD screen can display. If the charging indicator is red, wait for it to turn green. then the speedlite can be used. the red light means the speedlite is charging, the green means the flash can be used. 2.2 Speedlite testing Press (PILOT),then the speedlite is flashing.
Basic functions Turn on/ off the speedlite 2.3 Turn off the speedlite The power of flashlight can be closed when pressing ON/OFF button 2 seconds.
Basic functions 3.Memory function The speedlite will recover the last mode and setting when it's turned on again. 4: TTL mode The speedlite will flash automatically via the lense of the camera. 1 The speedlite is showed as the picture when it is on. 2 Decrease the exposure index Press the“ ”button to decrease the exposure index, fine adjustment from 0,-1/3,-2/3,-1......
Basic functions TTL mode 3 Increase the exposure index Press the“ ”button to decrease the exposure index, adjustment from 0,1/3,2/3,1 ...... 3 nine grades 4 How to use TTL Half press the shutter button for focusing The speedlite connects the camera and show the index of the aperture of the camera and the focal length of the lense. Press the shutter to photo, the speedlite will flash (TTL) automatically.
Basic functions 5: M mode Under the M( Manual setting) mode,you can set the flash index as you like. 1 Press button to change to M mode The picture is the M mode interface of the speedlite. 2 Increase the brightness of the speedlite. Press the " " button to set the brightness of the speedlite. The maximum brightness value of the speedlite is 1/1 (The-re're 3 grades of power fine adjustment on every gear) 3 Decrese the brightness of the speedlite.
Basic functions 6: Stroboflash( ) mode Stroboflash is a kind of model that can analyse the motion of subject. Under the stroboflash mode,the flash can photo a series of moving subjects for many photos. You can set the flash rate.( the flash times one second, use HZ to represent it),flash times and flash input. 1 Press to change to the stroboflash mode. The picture is the interface of the strobeflash.
Basic functions Stroboflash( ) mode 3 Decrease the input brightness of the flash Press the" " button to adjust the input brightness of the flash. The minimum brightness setting of the flash is 1/ 128 4 The strobeflash setting Pressbutton,the “ ” is blink,then you can set the strobeflash time of speedlite. The times of the strobeflash is from 1 to 90 (more parameters setting see P44 form). When the number of the times is set, you can adjust flash ferquency press button again.
Basic functions 4 Reference output frequency and times Fr eq ue s me ti x.
Basic functions 7:S1/S2 mode S1/S2 mode is used as off-camera auxiliary to creat various lighting effects. The S1 mode is suitable for manual flash environment, the S2 mode is suitable for TTL flash environment . Under these two modes, the adjustment of the output brightness of the speedlite is as the M mode. S1 When the flash is in S1 mode,it will flash with the first work of the master flash sync ,the same effect as the use of radio slave.
Basic functions S1/S2 mode S2 S2 mode is namely”pre-flash cancel mode”.It is similar to S1 mode,But it can ignored the pre-flash given by TTL flash.Therefore,it can support the main flash working in TTL mode.In particular,if S1 mode can not flash correctly and synchronically with your internal flash,you can try the S2 mode.(The function is suitable for the cameras of CANON and NIKON) S2 preflash can through the“ ” “ ”to adjust exposure brightness ! 1.
Basic functions 8. Sleep mode The flash will entry sleep mode if have any operation in 30 seconds. it can be wake up through any button. 9. ISO Display Camera ISO synchro to flash when shutter release halfpress, flash screen will hint “ISO-A” when camera set “auto ISO sensitivity control” on. 10. High speed sync The flash LCD will hint “H” word when set camera to “auto FP” on (Pay attentiion: software support shutter release 1/320 sync).
Basic functions 11. Rear-curtain synchronous display Flash LCD will hint “ ” when camera set to rear-curtain synchronous. 12. Aperture set Press set button entry operture mode, you can use “ F-1.0 to F-64. ”” ” button adjust aperture from 13.Manul setting the flash head zoom position You can adjust the zoom position of the flash head whenever which mode the speedlite is. The default focal length of the speedlite is 50MM.
Basic functions 15. Recover factory settings data At first continue to press button, then put batteries into speedlite, you can see manufacture data. 16. Overheating proteciton If the flash light is used too frequently, its overheating protection funciton will be triggered, the red and green lights of the charging indicator will blink alternatively, and the flash light will be locked. in such case, wait indicator to be green then cancel the protection before continuing the use.
The Advanced Application 1. Multi-flash Lighting Application Use inbuilt flash or top-mounted flash as master flash,Place speedlite in different directions. *In indoor application,radio signals can be reflected by walls; therefore, the placement of the slave flash should have more space. Wrieless triggering distance is up to 20-30M. *which can be avaiable in outdoor state.
The Advanced Application One master, three or more slave c.
The Advanced Application 2. Reflection Flash Bounce flash means to take photos by making flash light head aimed at will or ceiling and using the light reflected back from the ceiling or wall to light the desired object,so that the shade behind the object can be decreased to ger more natural shooting effect. If the wall or ceiling is too far,the bounce flash may be too weak to get enough exposure.
The Advanced Application thus make the eyes charming(catch light), this function can reach optimal effect when the flash head is up 90 degree. 4. Use Wide-angle Diffuser Pull out the wide-angle diffusion board,push back the reflection board and arrange them as per the figure; Iin such case,the flash scopes will extent to 18 mm and the flash effect will be softer and more natural.
Specifications Circuit design Guide Number Flash mode Vertical rotation angle Horizontal rotation angle Power supply Lighting times Recycle time Color temperature Flash time Flash control Wireless triggering distance Additional features Dimensions Net weight Accessories Insulated Gate Bipolar Transistro(IGBT) 68 meters (ISO 100,105mm) TTL,M,MULTI,S1,S2 0-90 degrees 0-270 degrees 4XAA size batteries(Alkaline or Ni-MH are usable) 100-1500 times(AA alkaline cell used) approx.
Guide number of different focal length range(at ISO 100, in meters / feet) 430 GN: 68 Flash output ISO 100 (meters / feet) Coverage(MM) 24 28 1/1 20/66 22/72.6 1/2 12.2/40.1 15.3/45.9 1/4 8.8/28.9 11/36.1 35 50 25/82 27/88.6 17.7/58.1 12.5/41 70 30/98.3 19.1/62.7 21.9/71.9 13.5/44.3 15.5/50.9 85 33/109.2 105 36/118.1 24/87.7 26.2/86 17/55.8 18.5/60.7 1/8 6.3/20.7 7.8/25.6 8.8/28.9 9.5/31.2 11/36.1 12/39.4 13.1/43 1/16 4.4/14.4 5.5/18 6.3/20.7 6.8/22.3 7.8/25.6 8.
Possible problems during use and solutions 1. Please note when use the flash outdoors:For outdoor application,please avoid direct sunlight to the wirless triggering sensor and ensure normanl use of the falsh. 2. Precaution for outdoor sue of lambency umbrella; The lambency umbrella mounted on the falsh light outdoors may be blowen down easily ,and the hot shoe of the flash light may be broken.Please fix the mounting rack or avoid outdoor use. 3.
Possible problems during use and solutions 7. Install batteries but can not turn on? Check the battery pack, the electricity shortage, old and new batteries or different brand battery in practice. if have these situation pls as to the right way to install batteries. *Caution: long time no use, please featch out batteries. The functions of this manual are based on test conditions of our company. Further notice will not be given if the design and specifications change.