Specifications

Protective cover
Electrical contacts
Camera battery compartment
cover slot
Vertical-grip operation switch
Vertical-grip AE start button
Vertical-grip AE lock/FE lock/Index
reduce button
Vertical-grip AF point selection/
Magnify button
Battery release lever
Battery compartment
INSTRUCTIONS
Thank you for purchasing Xit Product.
The XTCG5DIII is a battery grip that can hold two Battery Packs LP-E6
or six size-AA/LR6 batteries. It is also equipped with a vertical-grip
shutter button, Main Dial, etc. to enable shooting in the same way
as a horizontal grip.
ATTACHING TO THE CAMERA
1. Remove the battery from the camera (Fig. 1).
2. Detach the camera's battery compartment cover
3. Insert the detached cover into its storage slot to ensure that it will
not be lost(Fig. 3).
4. Remove the protective cover, and then insert the electrical contacts
into the battery compartment (Fin. 4-1).
5. Align the attachment screw with the camera's tripod socket, and then
turn the attach/detach knob to tighten securely to the camera (Fig. 4-2)
- Be sure to attach the battery grip to the camera before inserting
the batteries. The results of the battery check may not be
displayed properly if you attach the battery grip to the camera
with the batteries already inside.
- Before removing the battery grip from the camera, be sure to
turn the camera's power switch to <OFF>, and take out the
batteries. After removing the batteries, attach the protective
cover to the electrical contacts.
INSERTING THE BATTERY PACKS
1. Slide the lever as shown by the arrow and open the cover (Fig. 5)
2. Press both release levers outward in the battery compartment, and
remove the battery magazine (Fig. 6).
3. Insert one or two Battery Packs LP-E6 in the orientation shown on
the battery compartment cover (Fig. 7).
4. Close the battery compartment cover until it clicks into place.
- If only one battery pack is used, it may be inserted in either the
right or left sides.
- lf two battery packs are inserted, power is supplied
simultaneously by both battery packs. Two battery packs with
dierent charging levels can be inserted and used without any
problems.
- Remove the battery packs from the battery grip when the
camera will not be used for an extended period.
1. Insert the batteries into the Battery Magazine XTCG5DIII (Fig. 8).
Make sure the + and - battery contacts are properly oriented as
shown in the illustration.
2. Turn over the battery magazine so that the inserted batteries are
facing downward, and then insert the battery magazine until the
release lever locks into place (Fig. 9).
3. Close the battery compartment cover until it clicks into place.
INSERTING SIZE-AA/LR6 BATTERIES
- Fewer images can be shot when using size-AA/LR6 batteries.
Also, fewer images can be shot depending on the battery brand
and storage conditions, and so usage of size-AA/LR6 batteries
is recommended only for emergencies.
- With size-AA/LR6 batteries, use six new batteries of the same
brand at temperatures above 20°C/68°F. The camera may
not function when used in low temperatures or old and new
batteries are used together.
USING THE BATTERY GRIP
- Turning the vertical-grip operation switch to <ON> (Fig. 10) makes the
battery grip buttons and dial function in the same way as those
on the camera.
- When shooting in the horizontal-grip position, turn the vertical-grip
operation switch to <OFF> so that you do not accidentally use the
buttons or dial on the battery grip.
BATTERY LIFE
Temperature: +23°C /0°C 73°F/32°F [Number of shots - approx.]
Shooting method
Power supply
Model
Possible
shots
Viewnder shooting
EOS 5D
Mark III
LP-E6 x 2
1700/1500
AA alkaline/LR6 batteries
300/100
Live View shooting
LP-E6 x 2
400/360
- Based on ClPA (Camera & Imaging Products Association) testing standards,
the number of images that can be shot is reduced by holding the shutter
button halfway down for an extended time, and using the AF
frequently without shooting.
- The number of images that can be shot is reduced by frequent usage
of the LCD monitor.
- The battery level can be checked on the LCD panel of the camera and
in the viewnder.
SPECIFICATIONS
Type: Battery grip for the EOS 5D Mark Ill
Power sources: (1) One or two Battery Packs LP-E6
(2)AA alkaline/LR6 batteries x 6
Power switch: Camera's power switch
Working temperature range: 0°C - +40°C / 32°F - 104°F
Working humidity: 85% or less
Dimensions: 149.1 (W) x 114.3 (H) x 76.3 (D) mm/
5.9 (W) x 4.5 (H) x3.0 (D) in.
Weight: Approx. 315 g / 11.1 oz.
(not including the power
supply or battery magazine)
PART NAMES
1
2
3
4
5
6
7
8
9
Battery compartment cover
DC coupler cord mount
Attach/detach knob
Guide pin
Attachment screw
Battery compartment release lever
Vertical-grip shutter button
Vertical-grip Main Dial
Hand strap mount
Tripod socket
Battery magazine XTCG5DIII
10
11
12
13
14
15
16
17
18
19
20
Canon
designed for
Item # XTCG5DIII