User's Manual
Table Of Contents
- Microsoft Windows XP Tablet PC Edition 2005
- User Guide
- About This User Guide
- Chapter 1 Getting Started with Your Tablet PC
- Using the Motion Digitizer Pen
- Helpful Hints: Pen and Ink
- Complete the Microsoft Tablet PC Tutorials
- Review User Guide
- Open the Motion Dashboard
- Visit the Microsoft Help and Support Center
- Tablet PC Display
- Fingerprint Reader
- Motion AC Adapter
- Motion Battery Pack
- Battery Status LEDs
- Motion Dashboard
- Motion Third-Party Software Solutions
- Chapter 2 Using Your Motion Tablet PC
- Configuring Tablet and Pen Settings
- Calibrating and Using Your Digital Pen
- Using the Tablet PC Input Panel
- Helpful Hints: Using the TIP Window
- Motion Dashboard Audio System Controls
- Adjusting Display Settings and Screen Brightness
- Creating Schemes for External Monitors
- Helpful Hints: Mirrored and Extended Modes
- Configuring Your Power Management Settings
- Using Your Batteries
- Helpful Hints: Battery and Power Management
- Security Features and Settings
- Motion Security Center
- The Fingerprint Reader and Motion OmniPass
- Helpful Hints: Successful Fingerprint Captures
- Capturing a Fingerprint
- Capturing a Second Fingerprint Later
- Configuring Advanced OmniPass Features
- Logging Onto a Remembered Site
- The OmniPass Help application contains information about exporting your user profile. Go to Motion Dashboard then Motion Security Center > Motion OmniPass, and tap Help in the Action panel.
- Configuring Strong Logon Security
- Infineon Trusted Platform Module
- Windows Security System Components Overview
- Introduction to Speech
- Motion Speak Anywhere Technology
- Speech Recognition
- Helpful Hints: Dictating and Recording
- PC Cards
- SD Cards
- Infrared (IrDA) Port
- USB Ports
- Speaker Port (LE1600 only)
- Microphone Port (LE1600 only)
- DVI-D Connector (LE1600 only)
- VGA Connector
- Docking Connector
- Wi-Fi (802.11) Wireless Connections
- Bluetooth Wireless Connections
- Using the Bluetooth Application
- Helpful Hints: Bluetooth Wireless
- Using Infrared Wireless Connections
- Chapter 3 Care and Maintenance
- General Care
- Caring for the Standard and View Anywhere Displays
- Caring for the Motion Digitizer Pen
- Ordering New Pens
- Traveling by Air
- FAA Wireless Air Travel Requirement
- Other Travel Hints
- Appendix A Troubleshooting and Support
- Standard and Extended Warranty and Insurance Programs
- Appendix B Motion Tablet PC Specifications
58 Motion Computing LE1600 and LS800 Tablet PC User Guide
1 Narrow Angle; 2 Medium Angle; 3 Wide Angle; 4 Microphones (only two of
the three microphones are shown in this illustration of the LE1600 Tablet
PC).
• Skew angle. The pre-set sound detection area is straight in front of
the system display. If you want the system to receive sound from
elsewhere, you can skew the receiving direction towards one or the
other microphone (keeping the same relative angle of acceptance.
Setting up the skew angle for calibration:
1. Open the Motion Dashboard.
2. Under Microphone, tap Narrow Angle or Medium Angle. (You can-
not calibrate wide angle.)
3. Move to where you want the microphone to detect your voice.
4. Tap Calibrate. A block of text appears.
5. Read the text aloud, speaking normally towards the Tablet PC micro-
phones. This should take 20-40 seconds.
NOTE: In many cases, you will not need to calibrate the
microphone because the audio system filters out many
unwanted sounds. If you are dictating in an office or recording
during a meeting, the audio system may work well with no
additional calibration.
IMPORTANT: The audio system does not store calibrations. If
you change to another angle/position and then return to the
previous one, you must re-calibrate the audio system.
Enabling Speech Recognition Enrollment. It is necessary to train the
system to your voice before you can use the Speech Dictation and Voice
Command capabilities of the Tablet PC. The procedure is used to adjust the
microphones and train the Tablet PC for the characteristics of your voice.
The entire process takes about 10 minutes. It is advisable to move to a quiet
environment before starting this procedure.