User's Manual
Table Of Contents
- Microsoft Windows XP Tablet PC Edition 2005
- User Guide
- About This User Guide
- Chapter 1 Getting Started with Your Tablet PC
- Using the Motion Digitizer Pen
- Helpful Hints: Pen and Ink
- Complete the Microsoft Tablet PC Tutorials
- Review User Guide
- Open the Motion Dashboard
- Visit the Microsoft Help and Support Center
- Tablet PC Display
- Fingerprint Reader
- Motion AC Adapter
- Motion Battery Pack
- Battery Status LEDs
- Motion Dashboard
- Motion Third-Party Software Solutions
- Chapter 2 Using Your Motion Tablet PC
- Configuring Tablet and Pen Settings
- Calibrating and Using Your Digital Pen
- Using the Tablet PC Input Panel
- Helpful Hints: Using the TIP Window
- Motion Dashboard Audio System Controls
- Adjusting Display Settings and Screen Brightness
- Creating Schemes for External Monitors
- Helpful Hints: Mirrored and Extended Modes
- Configuring Your Power Management Settings
- Using Your Batteries
- Helpful Hints: Battery and Power Management
- Security Features and Settings
- Motion Security Center
- The Fingerprint Reader and Motion OmniPass
- Helpful Hints: Successful Fingerprint Captures
- Capturing a Fingerprint
- Capturing a Second Fingerprint Later
- Configuring Advanced OmniPass Features
- Logging Onto a Remembered Site
- The OmniPass Help application contains information about exporting your user profile. Go to Motion Dashboard then Motion Security Center > Motion OmniPass, and tap Help in the Action panel.
- Configuring Strong Logon Security
- Infineon Trusted Platform Module
- Windows Security System Components Overview
- Introduction to Speech
- Motion Speak Anywhere Technology
- Speech Recognition
- Helpful Hints: Dictating and Recording
- PC Cards
- SD Cards
- Infrared (IrDA) Port
- USB Ports
- Speaker Port (LE1600 only)
- Microphone Port (LE1600 only)
- DVI-D Connector (LE1600 only)
- VGA Connector
- Docking Connector
- Wi-Fi (802.11) Wireless Connections
- Bluetooth Wireless Connections
- Using the Bluetooth Application
- Helpful Hints: Bluetooth Wireless
- Using Infrared Wireless Connections
- Chapter 3 Care and Maintenance
- General Care
- Caring for the Standard and View Anywhere Displays
- Caring for the Motion Digitizer Pen
- Ordering New Pens
- Traveling by Air
- FAA Wireless Air Travel Requirement
- Other Travel Hints
- Appendix A Troubleshooting and Support
- Standard and Extended Warranty and Insurance Programs
- Appendix B Motion Tablet PC Specifications
46 Motion Computing LE1600 and LS800 Tablet PC User Guide
IMPORTANT: To get a feel for finger position and swipe
speed, tap Practice. “Practice” takes you through all the
enrollment steps and helps you get a successful fingerprint
scan. You are asked to scan the same finger three times.
5. After you have practiced, you will be asked to scan one more time for
verification. After the verification is successful, tap Next to scan your
finger again, this time for real (not practice).
6. Place the selected finger over the nickel-colored ring and slowly, with
moderate pressure, drag your finger across the sensor from right-to-
left or left-to-right. Make sure your entire fingerprint (i.e., your finger-
tip, not your whole finger) touches both the nickel-colored ring and
the sensor surface.
Successful fingerprint capture: If the capture is successful,
you will see a green fingerprint image in the capture area. If
the capture is unsuccessful, an information message
appears, such as “Scan too slow/too fast...” and the green
fingerprint will not appear. Swipe your finger across the
sensor again as many times as required for a successful scan.
7. After the first scan is successful (and a green fingerprint image
appears), OmniPass prompts you to scan your fingerprint additional
times. Wait until the green fingerprint disappears from the display
and the fingerprint image area is blank before swiping your finger
again. After OmniPass successfully captures the same fingerprint
three times, the Verify Fingerprint window appears. Swipe your fin-
ger one more time to complete the enrollment.
When the messages “The selected finger has been enrolled in
OmniPass” and “Verification Successful!” and a green fingerprint
image appear, enrollment is successful and complete.