User's Manual
Table Of Contents
- Microsoft Windows XP Tablet PC Edition 2005
- User Guide
- About This User Guide
- Chapter 1 Getting Started with Your Tablet PC
- Using the Motion Digitizer Pen
- Helpful Hints: Pen and Ink
- Complete the Microsoft Tablet PC Tutorials
- Review User Guide
- Open the Motion Dashboard
- Visit the Microsoft Help and Support Center
- Tablet PC Display
- Fingerprint Reader
- Motion AC Adapter
- Motion Battery Pack
- Battery Status LEDs
- Motion Dashboard
- Motion Third-Party Software Solutions
- Chapter 2 Using Your Motion Tablet PC
- Configuring Tablet and Pen Settings
- Calibrating and Using Your Digital Pen
- Using the Tablet PC Input Panel
- Helpful Hints: Using the TIP Window
- Motion Dashboard Audio System Controls
- Adjusting Display Settings and Screen Brightness
- Creating Schemes for External Monitors
- Helpful Hints: Mirrored and Extended Modes
- Configuring Your Power Management Settings
- Using Your Batteries
- Helpful Hints: Battery and Power Management
- Security Features and Settings
- Motion Security Center
- The Fingerprint Reader and Motion OmniPass
- Helpful Hints: Successful Fingerprint Captures
- Capturing a Fingerprint
- Capturing a Second Fingerprint Later
- Configuring Advanced OmniPass Features
- Logging Onto a Remembered Site
- The OmniPass Help application contains information about exporting your user profile. Go to Motion Dashboard then Motion Security Center > Motion OmniPass, and tap Help in the Action panel.
- Configuring Strong Logon Security
- Infineon Trusted Platform Module
- Windows Security System Components Overview
- Introduction to Speech
- Motion Speak Anywhere Technology
- Speech Recognition
- Helpful Hints: Dictating and Recording
- PC Cards
- SD Cards
- Infrared (IrDA) Port
- USB Ports
- Speaker Port (LE1600 only)
- Microphone Port (LE1600 only)
- DVI-D Connector (LE1600 only)
- VGA Connector
- Docking Connector
- Wi-Fi (802.11) Wireless Connections
- Bluetooth Wireless Connections
- Using the Bluetooth Application
- Helpful Hints: Bluetooth Wireless
- Using Infrared Wireless Connections
- Chapter 3 Care and Maintenance
- General Care
- Caring for the Standard and View Anywhere Displays
- Caring for the Motion Digitizer Pen
- Ordering New Pens
- Traveling by Air
- FAA Wireless Air Travel Requirement
- Other Travel Hints
- Appendix A Troubleshooting and Support
- Standard and Extended Warranty and Insurance Programs
- Appendix B Motion Tablet PC Specifications
82 Motion Computing LE1600 and LS800 Tablet PC User Guide
The Tablet PC won’t come out
of Hibernation mode when
running on battery power.
Fully discharged battery and
no AC power.
Connect the AC adapter to
provide power to the Tablet PC
and charge the battery.
The display goes black while
the Tablet PC is still turned on.
The Tablet PC system has
gone into stand by after sitting
idle for a period of time. (In this
state, the power LED flashes
blue.)
Slide the power switch for
about a second to resume
operations.
System has gone into low-
battery Hibernation mode. (In
this state, the power LED is
off.)
1. Slide the power switch for
about a second to resume
operations. 2. Connect the AC
adapter to the Tablet PC to
charge the battery.
BATTERY
Data loss during battery swap. The unit is designed to
maintain the data and settings
for up to 30 seconds in stand
by while you swap the battery.
This time may vary due to your
system and the programs
you’re running.
When you swap the battery
with the unit in stand by, be
sure to save your data before
removing the battery to avoid
data loss.
The battery seems to run down
very quickly (lasting less than
three hours after a full charge).
Accessory devices such as a
DVD player and applications
that make heavy use of the
hard drive drain the battery
more quickly.
Use AC power when possible
and/or turn off the accessory
devices.
The battery is weakening or
defective.
All batteries weaken over time,
but if a new battery is needed,
visit the Motion website to
order a new battery.
DISPLAY
The desktop is too big for the
display – I can’t see all of the
desktop icons.
Screen resolution is set higher
than the default with 32-bit
resolution.
Decrease the screen resolution
by opening the Motion
Dashboard, selecting Graphics
Properties, then the Schemes
tab.