Xplova E7 Smart Cycling Computer User’s Manual
© Copyright 2015, Xplova Incorporated. This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this User’s Manual, nor any of the material contained herein, may be reproduced without written consent of the manufacturer. Download the latest version of this document at www.xplova.com. Visit http://tour.xplova.
Getting Started 5 Features of the Xplova E7 5 Getting to Know the Xplova E7 7 Accessories 8 ANT+ Accessories 8 Charging the Xplova E7 9 Installing Xplova E7 on bike 10 Using Xplova E7 11 Acquiring GPS Signal 12 The LCD Screen 12 Selecting Data Display 15 Adjusting the Backlight 16 Selecting Bike Profile 16 Marking Lap / Location 17 Restarting Recording 18 Idle Mode 18 Changing the Settings 19 Menu Button Controls Description 19 The Menu Tree 20 1.
13. LANGUAGE Menu 44 14.
Getting Started Congratulations on having purchased the Xplova E7 Smart Cycling Computer. In this chapter, you will discover key features and understand how to set up your device and use the basic features of the user interface. Features of the Xplova E7 The Xplova E7 is a light-weight and stylish GPS Cycling Computer for performance driven cyclists and those who are keen to share their cycling journeys with friends.
• High precision Barometric altimeter for altitude and slope calculation • Low power digital wireless sensors support (ANT+) for Combo cadence sensor, Heart Rate Monitor, Power Meter, Speed sensor, Cadence sensor, etc.
Getting to Know the Xplova E7 Xplova E7 Front View Power • Short press to turn the power on microUSB連接埠 (在防⽔水蓋下) • Short press to switch the data displayed on the upper screen • Long press to turn the power off • Long press to enter or exit the menu. • Short press to change the backlight level • Short press to mark lap and position.
Accessories The Xplova E7 comes with the accessories shown below. Check to make sure all items are included in the package; if anything is missing, contact your Xplova retailer. Standart Accessories • Micro USB Cable • Bike Mount with • Rubber Bands Optional Accessories The Xplova E7 can be paired with optional accessories to provide a complete solution for cycling and outdoor activities.
Charging the Xplova E7 Before using your Xplova E7, make sure it is properly charged and ready to go. Charge the Xplova E7 for at least 3 hours before first use to make sure the built-in battery is fully charged. Xplova E7 can be charged using the supplied USB cable to connect to any standard USB port or USB power adapter.
Installing Xplova E7 on bike 1. Align the mount pad to the bike handle bar and the bike mount to the mount pad. 2. Loop a rubber band from one corner of the bike mount, passing through the bottom side, to the other corner. 3. Loop a rubber band from another corner, passing through the bottom side, to the other corner to secure the bike mount in place. 4. Align the mounting guide to the bike mount. 5. Install and then turn the Xplova E7 clockwise to lock it in place.
Using Xplova E7 This chapter provides instructions on how to power up your device and use the button controls and full features and functions of your Xplova E7. Powering Up the Xplova E7 After charging the Xplova E7, you are now ready to begin using your device. Short press version. . The LCD screen briefly displays the device firmware NOTE: During charging long press 3 sec. to power on. NOTE: The firmware version may appear differently from the above illustration.
Acquiring GPS Signal The Xplova E7 comes fully equipped with X-Navi technology designed to maximize your cycling experience. Once turned on, the Xplova E7 automatically searches for satellite signals. Go outside to an area free from tall obstructions. The greater the exposure, the faster the Xplova E7 will be able to acquire a signal. Signal acquisitions can take 5 to 15 minutes to complete under open skies. The GPS icon indicates the signal strength when GPS is fixed.
Selected Bike: Shows the current selected bike profile Bike 1 is selected with its connected accessories settings Bike 2 is selected with its connected accessories settings Customized settings for running, walking, driving or Bike 3 Bluetooth Connected Shows when connected with Xplova Meetup APP GPS Signal Status Shows the GPS signal strength Good GPS signal reception, 3D fixed Fair GPS signal reception, 2D fixed Poor GPS signal reception, not fixed Searching GPS signal, not fixed No GPS signal GPS is t
Cadence Sensor receiver is on but no signal received No Cadence Sensor icon Cadence Sensor receiver is off Speed Status Display the current speed is above or under average trip speed Current speed is above average trip speed Current speed is under average trip speed Recording Status Display the recording status In recording Pause recording: When current speed is lower than the Smart-Pause speed setting, Xplova E7 data recording will be paused.
Selecting Data Display The LCD display shows different types of data DATA1: Upper Screen Data, Main data display area Short press repeatedly to toggle the upper data display for Current data, Average data and Maximum data.
。 。 。 Short press Short press Short press Total Climb, Trip Time. Altitude + Slope, Trip Time Bike1 ODO, Clock. 。 。 Short press Short press Current Power + Left % Right Power, Trip Time Calories + Temperature, Trip Time. Adjusting the Backlight To adjust the brightness setting, short press repeatedly to scroll through the brightness options. Options are: HIGH, LOW, OFF. Selecting Bike Profile You can configure up to three bike profiles on Xplova E7: (Bike2), and CUST (Custom.) 1.
Main display page Gear selection Short press Long press 3 Sec. 3. Short press short press save and return to confirm selection. Operation note: • The short press • appears on the upper right scree for Bike profile selection, to scroll the options. The appears on the lower left screen for confirmation, short press to confirm selection. Marking Lap / Location During recording, press to mark a new LAP or mark the current location to the current recording session.
Restarting Recording During recording, long press to start a new recording. New record R02 In recording New record number Long Press 3 sec. New record starts Starts the new record R02 Countdown to store the record R01 The Xplova E7 starts recording when it is powered on, if you want to reset the time and distance from zero, you can long press for 3 seconds, the Xplova E7 starts countdown, stores the current record and displays the current record number, e.g. R01 and then starts a new record, e.g.
Changing the Settings The Xplova E7 has a number of customizable settings available so you can control functionality and personalize your device. To bring up the menu, long press . Main screen Enter the Menu Long Press 3 sec. Menu Button Controls Description Indicate the function of DATA1 button Name of Menu or Option Indicate the function of DATA2 button Confirm the Option and return to previous screen Setting of Options button Short press Short press button to scroll to the next Menu.
Indicate the [setting of option] is selectable when it is blinking A blinking field is the current data field. Short press button to select the value, short press button to scroll to the next field. Return button Indicate short press previous screen. to confirm and save the option and return to The Menu Tree 1. ALT (Altitude) : Altitude calibration, allows you to pre-set up to three altitude settings. 2. RECORD: Allows you to view your activity records. 3.
1.ALT (Altitude) Menu The Xplova E7 measures the altitude using a high-resolution barometric altimeter. The Altitude menu allows you to calibrate the altimeter to ensure accuracy. The altimeter is highly sensitive to changes in air pressure and may be affected by changing weather conditions. It is recommended to periodically calibrate the altimeter.
4. You can manually set the current altitude value into [CURR ALT] or select the [GPS ALT] : altitude value received from the GPS as the current altitude. 4.1.To manually set the altitude value under [CURR ALT] 4.2.Short press 4.3.Short press [DATA2] to enter the setting. [DATA1] to adjust the value. 4.4.Short press [DATA2] to move to another field digit. 4.5.Short press to confirm the value and return to previous screen. 4.6.Short press to return to the menu: 1. ALT 5.
set bridges, tunnels or high buildings as the reference pint to avoid the altitude discrepancy by artificial architectures. Please connect your Xplova E7 to your computer, sign-in tour.xplova.com then clicking [Device settings]. Note: please install the [JAVA plugin] in your browser to ensure the interoperability between tour.xplova.com and the Xplova E7 work properly.
Click the position where you want to get the altitude from the map, click the [Set altitude] to confirm the setting.
Restore [My configurations] back to the Xplova E7 2. RECORD Menu With the RECORD menu, you can view the record summary in an activity. When the remaining memory is less than 3%, the oldest record will be overwritten. The record time depends on the enabled sensors. • GPS only:around 220 hours • GPS + Combo sensor or GPS + HRM:around 180 hours • GSP + Combo sensor + HRM:around 160 hours • GPS + Combo sensor + HRM +power meter : abound 70~120 hrs depends on power meter data format.
you want to view the information. 2015 JAN17 02 means the 2nd record of 2015 Jan 17. 6. Short press [DATA2] to confirm the selection. The screen shows R[NUM] and its starting time and date. If there are multiple records in an activity, it will be serially numbered in the R[NUM]. 7. Short press the information. [DATA1] to the R[NUM] of the activity you want to view Note: this option is only available when there are multiple records in an activity 8. Short press [DATA2] to confirm the selected record.
5 Select activity 4 Confirm selection 9 8 Confirm selection 9 9 Select view page Select view page AVG (Average): Average heart rate、 Average cadence、Average Speed、Average power. 9 Select view page Others: Summary of Calories burned、Total climb Select record number 6 Enter RECORD list Record number: Record distance,Record time. 7 LAP Count 27 Select view page MAX (Maximum): Maximum heart rate、 Maximum cadence、 Maximum Speed、 Maximum power.
WARNING Menu With the WARNING menu, you can set up alerts to help you stay within predefined ranges during your bicycle riding. You can program the Xplova E7 to warn you when you exceed set durations, distances, calories, heart rate or AUTOLAP mark. • BY TIME: Set a duration after which the alarm will sound and display a warning message. • BY DIST: Set a distance after which the alarm will sound and display a warning message.
6. Short press [DATA1] repeatedly to scroll through the options: • (Value): Select to activate the function and set the limit. • OFF: To deactivate the function. • ON: To activate the function (Only available in AUT-LAP submenu). 7. If you select (value), short press 8. Short press [DATA2] to confirm the selection. [DATA1] repeatedly to adjust the value. 9. Short press [DATA2] to move to another field digit. 10.Short press 11.Short press to confirm the value and return to the previous screen.
● OFF: To turn off t he GPS receiver. ● ON: To turn on the GPS receiver. 7. Short press screen. [Return] to confirm the setting and return to the previous 8. Short press [Return] to return to the main display screen. To view the GPS signal strength: The GPS strength indicates the GPS reception status and the number of satellites which have been detected.
4 Scroll options 3 5 Enter GPS Menu Enter submenu 6 6 Select [YES] Select [NO] 2. Short press 3. Short press [DATA1] repeatedly to scroll to 4. GPS Menu. [DATA2] to enter the list of GPS options. 4. Short press 5. Short press [DATA2] to enter the list of GPS options. [DATA2] to enter the submenu. 6. Short press to reset GPS receiver or short press to cancel. 7. Short press [Return] to return to the previous screen. 8. Short press [Return] to return to the main display screen. 5.
• ON: To enable sounds. 5. Short press screen. [Return] to confirm the setting and return to the previous 6. Short press [Return] to return to the main display screen. 6. S-PAUSE (Smart Pause) Menu The S-PAUSE menu allows you set the minimum speed limit. By which when the current speed is under the specified speed, the device will automatically pause.
7. Bike Menu The BIKE menu allows you to configure the bike wheel size and set the current bike to pair with a standard ANT+ combo cadence sensor, standalone cadence sensor, standalone speed sensor or a power meter. 5 Scroll BIKE options 4 Enter BIKE options 1. Long press [DATA1] to bring up the menu. 2. Short press [DATA1] repeatedly to scroll to 7. BIKE Menu. 3. The screen shows the selected bike: (Custom) 4. Short press (bike1), (bike2) or CUST [DATA2] to enter the list of BIKE options. 5.
To pair a Combo (Speed/Cadence) Cadence Sensor: Scroll through the BIKE options to [CMB]. Note: Leave the CMB OFF if there is no Combo Cadence Sensor installed on your bike. 12 Select CMB ON 11 13 Enter Submenu Enter SCAN 14 14 Rescan Confirm & setting 11.Short press in scanning & pairing 15 Return [DATA2] to enter the [CMB] submenu. 12.Short press [DATA1] repeatedly to scroll to the option [CMB ON]. 13.
To pair a Cadence Sensor: Scroll through the BIKE options to [CAD]. Note: Leave the CAD OFF if there is no standalone Cadence Sensor installed on your bike or there is a COMBO Cadence Sensor has been installed and paired already. 17 Select CAD ON 16 18 Enter SCAN Enter Submenu 19 19 Confirm & setting 16.Short press Rescan in scanning & pairing 20 Return [DATA2] to enter the [CAD] submenu 17.Short press [DATA1] repeatedly to scroll to the option [CAD ON]. 18.
22 Select SPD ON 21 23 Enter SCAN Enter Submenu 24 24 Confirm & setting Rescan 21.Short press 22.Short press in scanning & pairing 25 Return [DATA2] to enter the [SPD] submenu [DATA1] repeatedly to scroll to the option [SPD ON]. 23.Short press [DATA2] to scan for the speed sensor, in the meantime, enable the speed sensor during the scanning. After paired, a set of speed sensor device ID will be appeared on the screen. 24.If paired successfully. Short press return to the previous screen.
22 Select SPD ON 21 23 Enter Submenu Enter SCAN 24 24 Rescan Confirm & setting in scanning & pairing 25 Return To pair a Power Meter: 26.Short press [DATA2] to enter the [PWR] submenu 27.Short press [DATA1] repeatedly to scroll to the option [PWR ON]. 28.Short press [DATA2] to scan for the power meter, in the meantime, enable the power meter during the scanning. After paired, a set of power meter device ID will be appeared on the screen. 29.If paired successfully.
appeared on the screen. 33.If calibrated successfully. Short press return to the previous screen. ● If not, short press [Return] to confirm the setting and [DATA2] to recalibrate the power meter. To determine which power meter data to be displayed in the main display screen: Short press [DATA2] to enter the [PWR] submenu. 34 Select DISP 36 35 Scroll DISP options Enter setting 36 36 36 36 Scroll DISP options Scroll DISP options Scroll DISP options Scroll DISP options 34.Short press 35.
● NOW/L%R: Current power output (W)] / Left power output % 、 Right power output % 8. HRM (Heart Rate Monitor) Men The HRM menu allows you to monitor your exercise and body condition. To pair Heart Rate Monitor: 4 Select HRM ON 3 Enter SCAN Enter HRM options 6 6 Confirm & setting in scanning & pairing 7 Rescan Return 1. Long press [DATA1] to bring up the menu. 2. Short press 3. Short press 4. Short press [DATA1] repeatedly to scroll to 8. HRM Menu. [DATA2] to enter the list of HRM options.
9. USER Menu The USER menu allows you to edit information about yourself. 4 Scroll options 4 Scroll options 3 5 9 Enter USER options Enter submenu Enter submenu 4 4 Scroll options Scroll options 19 14 Enter submenu Enter submenu 1. Long press [DATA1] to bring up the menu. 2. Short press 3. Short press [DATA1] repeatedly to scroll to 9. USER Menu. [DATA2] to enter the list of USER options. 4.
screen. To setup Weight: 13.Short press [DATA1] repeatedly to scroll to WEIGHT option. 14.Short press [DATA2] to enter WEIGHT submenu. 15.Short press [DATA1] repeatedly to adjust the value. 16.Short press [DATA2] to move to another field digit. 17.Short press [Return] to confirm the setting and return to the previous screen. To setup Height: 18.Short press [DATA1] repeatedly to scroll to HEIGHT option. 19.Short press [DATA2] to enter HEIGHT submenu. 20.
(Device Name), S/N (Device Serial Number), VER (Device Version). 5. When scroll to NAME; short press [DATA2] to enter NAME submenu. The device name is appeared in the Xplova Meetup APP when establishing the Bluetooth connection. 6. Short press [DATA1] repeatedly to adjust the value. 7. Short press [DATA2] to move to another field digit. 8. Short press screen. [Return] to confirm the setting and return to the previous 9. Short press [Return] to return to the main display screen. 11.
6. Short press [DATA1] repeatedly to adjust the time zone value. 7. Short press screen. [Return] to confirm the selection and return to the previous 8. Short press [DATA1] repeatedly to scroll to DST; short press ] to enter DST submenu. [DATA2 9. Short press [DATA1] to select ON or OFF. 10.Short press screen. [Return] to confirm the selection and return to the previous 11.Short press [Return] to return to the main display screen.
13. LANGUAGE Menu The LANGUAGE menu allows you to set the default language. 4 Scroll options 3 5 Enter LANGUAGE options Confirm selection 1. Long press [DATA1] to bring up the menu. 2. Short press 3. Short press 4. Short press [DATA1] repeatedly to scroll to 13. LANGUAGE Menu. [DATA2] to enter the list of LANGUAGE options. [DATA1] repeatedly to scroll through the LANGUAGE option 5. Short press screen. [Return] to confirm the selection and return to the previous 6.
• Short press press to select NO: return to the previous screen; short [Return] again to return to the main display screen.
The Accessories Heart Rate Monitor (Optional accessory from Xplova) The Heart Rate Monitor (HRM), XA-HR2 from Xplova is attached to an elastic band worn around the chest. Wearing the heart rate monitor Wear the heart rate monitor around your chest as close as possible to the heart with the monitor segment worn in the middle of the chest. For best contact, wet the contact rubber before wearing.
1. Using a coin, turn the battery cover on the back of the sensor counterclockwise until it opens. 2. Remove the old battery and replace with a new one. 3. Replace the battery cover and tighten with a coin. Note: To extend the life cycle of the textile belt, please detach it from the main unit and softly clean the belt with water after exercise.
Combo Cadence Sensor (optional accessory from Xplova) The combo cadence (includes the cadence sensor and a speed sensor), XACS1 or XA-CS2 from Xplova, attaches to the chain stay of your bike to help you track your speed and cadence accurately. Installing the Combo Cadence Sensor 1. Position the sensor on the chain stay of your bike. 2. Use the supplied cable ties to hold the sensor in place. Do not fully tighten. 3. Attach the magnet to a spoke. Do not fully tighten. 4.
5. Attach the magnet to the left crank. Do not fully tighten. 6. Adjust the magnets and the sensors, making sure the air gap between sensor markings and magnets is less than 5 mm. 7. When setup is complete, tighten the cable ties.
Changing the Combo Cadence Battery 1. Using a coin, turn the battery cover on the back of the sensor counterclockwise until it opens. 2. Remove the old battery and replace with a new one. 3. Replace the battery cover and tighten with a coin.
Appendix Xplova E7 Specifications Hardware Size & Weight 55 (L) x 54 (W) x 19.6 (H) mm, 57.7 g Display 38 x 28 mm (1.
Wheel Size Table ETRTO 47-305 47-406 47-507 23-571 37-590 Wheel Spec. Circumference (mm) ETRTO Wheel Spec. Circumference (mm) 12 x 1.75 935 40-559 26 x 1.50 2010 14 x 1.50 1020 47-559 26 x 1.75 2023 14 x 1.75 1055 50-559 26 x 1.95 2050 16 x 1.50 1185 26 x 2.00 2055 26 x 2.10 2068 26 x 2.125 2070 26 x 2.35 2083 26 x 3.
Note:Actual wheel circumference might be varies for different brand. Declarations of Conformity Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Duales System Deutschland GmbH Participant CE Declaration of Conformity (CENELEC Europe) WEEE directive Disposal of Waste Electrical and Electronic Equipment by users in private households in the European Union. This symbol on the product or on the packaging indicates that this can not be disposed of as household waste. You must dispose of your waste equipment by handling it over to the applicable take-back scheme for the recycling of electrical and electronic equipment.