Operation Manual Drywall Sander 62830 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps, and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities, please contact us.
The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
Introduction Thank you for purchasing this quality product. To minimise the risk of injury we urge that our clients take some basic safety precautions when using this device. Please read the operation instructions carefully and make sure you have understood its content. Keep these operation instructions safe.
• • • • exchange of sanding disks. Abide by the instructions concerning the replacement or lubrication of parts. Before connecting the device to a power supply, ensure that its on/off switch can be moved without any obstructions. Do not use the device if it cannot be turned on or off properly. Always make sure that the device has been turned off before connecting it to a power supply and only connect it to an outlet matching its specifications.
Main components ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) № Name № Name 1 Upper cooling element 7 Speed regulator switch 2 Heavy duty engine 8 Power switch 3 Rotary disk 9 Dust bag connection 4 External carbon brush 10 Side handle 5 Handle 11 LED light 6 Speed regulator Accessories № Name Qty. № Name Qty. 1 Dust bag 1 5 Sanding disk 6 2 Suction hose 1 6 Carbon brush 1 pair 3 Side handle 1 7 Socket head wrench 1 4 Adapter 1 https://www.XPOtool.
Power switch and speed regulator • • • • The power switch of this drywall sander is self-locking and can be locked in its “ON” position. When activating the device, press its power switch to start it. The device can be turned off by simply pressing the power switch. It is not necessary to activate its self-locking function by pressing the self-lock button.
depending on the size of their graining and are suited for different surfaces. The larger the grains of a sanding disk, the easier is the removal of rough irregularities on a surface or the roughening of smooth surfaces. Assembly instructions 1. 2. 3. 4. Remove sanding disk from the rotary disk. Place the socket head wrench in the central hole of the rotary disk. Turn the socket head wrench clockwise to loosen and remove the disk.
Exchanging carbon brushes The device is delivered with a set of spare brushes that can be used to replace the pre-installed carbon brushes once they are worn out. The carbon brushes should always be replaced as a set. 1. Turn the device off and properly disconnect it from its power supply before beginning the exchange of the carbon brushes. 2. Open the protective cover located at the top of the device with help of a socket head wrench and remove the worn carbon brushes. 3.
Exploded drawing and parts lists № Name Qty. № Name Qty. 1 Screw M5 1 25 Spacer 1 2 Rotary disk 1 26 Rotor 1 3 Rotary disk cover 1 27 Spacer 1 https://www.XPOtool.
4 Screw (ST4.2×12) 7 28 Bearing 1 5 Spacer 7 29 Bearing bushing 1 6 Swivel plate cover 1 30 Round inductor 2 7 Spindle fuse 35 1 31 Carbon brush fixture 2 8 Air intake button (⌀35) 1 32 Carbon brush 2 9 Swivel plate 1 33 Carbon brush cover 2 10 Disk spring 4 34 Right housing 1 11 Screw (ST4.2×25) 4 35 Right housing cover 1 12 Screw (ST4.2×22) 2 36 Left housing 1 13 Cover 1 37 Left housing cover 1 14 Oil seal 1 38 Screw (ST4.
Disposal regulations EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2012/19/EU) were implemented in the law related to electrical and electronic equipment and appliances. All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.