INSTALLATION GUIDE & USER’S MANUAL WALL MOUNT RANGE HOOD Pro-X Series: PX01-W30/36 PX02-W30/36 PX03-W30/36 PX04-W30/36/42 PX04-W30/36/42-B PX06-W30/36/42 PX15-W30/36/42 SP03-W30/36/42 Ultra Series: D02-W30/36 UL02-W30/36 UL03-W30/36 Deluxe Series: DL08-W36/42/48 IMPORTANT: READ AND SAVE THESE INSTRUCTIONS FOR RESIDENTIAL & INDOOR USE ONLY www.XtremeAirUsa.
TABLE OF CONTENTS 1 IMPORTANT SAFETY INSTRUCTIONS ......................................................................................................................... 2 2 HEIGHT & CLEARANCE ............................................................................................................................................ 3 3 VENTING REQUIREMENT ..........................................................................................................................................
2. HEIGHT & CLEARANCE 3. VENTING REQUIREMENTS IMPORTANT: NEVER exhaust air or terminate ductwork into crawl spaces, between walls, ceiling, attics or garages. All exhaust must be ducted to the outside. Hood mounted too low could result in heat and/or fire hazard. Hoods mounted too high will be hard to reach and will lose its performance and efficiency. Use metal ductwork only. DO NOT use plastic ventilation. DO NOT use 4” (10.2 cm) laundry-type wall caps.
7.
8. HOOD DIMENSIONS & INSTALLATION OVERVIEW PX01-W30/36 PX02-W30/36, UL02-W30/36 PX04-W30/36/42 & PX06-W30/36/42 DL08-W36/42 www.XtremeAirUsa.
9. INSTALLATION \ STEP 1: (OPTIONAL ONLY) PROTECT THE COOK TOP & CREATE WORK STATION Have 2 pieces 2” x 4” x 20” on both sides of stove & plywood on top of them to protect cook top or stove from damage or debris. This plywood will also create a comfortable work station for easy installation of hood unit. STEP 2: MARKING ON THE WALL A. Center: is the center of cook top or stove. B. Chimney width: is the width of the chimney (Varies with each model). C.
STEP 6: SECURE THE HOOD BODY & TEST RUN A. B. C. D. Use a stud finder to find all studs below the hood body. Put blue tape on every stud found. Use 1/8” drill bit to drill though the back of hood in line with blue tape. Secure the hood body by using the 2.0 inches wood screws (provided) through the back of hood to the stud. Refer to page 8, Range Hood Operation. Try a few test runs to ensure machine is running properly. STEP 6A: FOR PX01 MODEL ONLY – INSTALL GLASS CANOPY A. B.
F. Remote Control Sensor: 1. Remote control sensor receives infrared (IR) signal from the remote control. The maximum distance for IR data transmission is 10 feet and requires direct line of sight. The transmission distance may vary depending on temperature and remote control battery condition. 2. Light settings are independent from other settings (including power-off delay) and lights have to be manually turned on or off. 3.
3. FOR ALL ULTRA SERIES: TYPE 3: MECHANICAL BUTTON CONTROL A. Activating Blower Function: Press your designed speed (1,2,3) B. Turn off power: While the blower (motor) is running, press button (0) to turn off the motors. C. To turn the light ON/OFF While the light is off, press button (4) once to turn on the light. Press button (4) again to turn the light off 4. FOR DL08 & DL09 Model: TYPE 4: ELECTRONIC BUTTON CONTROL A.
3. 4. 5. 6. 7. The blower or fan seems weak: Check that the duct sized used is at least 6”. Range hood WILL NOT function efficiently with insufficient duct size & loosely secured. Check if duct is clogged or if damper unit (half-circular flapper) is not installed correctly or opening properly. A tight mesh on a side wall cap unit might also cause restriction to the air flow. The lights work but the blower is not spinning at all, is stuck or is rattling.
16. LIMITED WARRANTY www.XtremeAirUsa.
