Operation Manual

10
11
the Dock wIll allow You to Power anD charge
Your IPoD/IPhone/IPaD whIle transmIttIng
over Bluetooth
1. Remove the dock, back support, screw and AC adapter
from the packaging and properly dispose of any packaging
materials.
2. Place unit on a level surface close to a power outlet following
the precautions listed in the safety warnings.
3. Place the back support with the tall edge facing outward on
the top of the dock aligning the center slit over the screw hole.
4. Place the screw over the slit and align with the hole on the
unit. Gently tighten about half way by turning the screw
clockwise. The back support should be able to slide to the
front and back loosely.
5. Carefully place your device into the dock connector and slide
the back support to fit snuggly against your device.
6. Gently tighten the screw all the way to secure the back
support into place.
7. If located in the US, skip to step 10. If located outside the US,
select the appropriate wall adapter. If already attached to the
unit, skip to step 10.
8. Press the button under the wall adapter to release the adapter.
9. Gently slide in the appropriate wall adapter. You will hear a
click when it is properly locked into place.
10. Connect the AC adapter jack to the back of the unit and then
connect the other end of the adapter to a power outlet.
settIng uP the PowereD Dock
lIstenIng to Your IPoD/IPhone through the
Dock connector
1. If playing an iPhone, skip to the next step 3.
2. If playing an iPod classic, touch or nano, insert the included
adapter into the two holes behind the dock connector and
press firmly to ensure a proper connection.
3. Carefully place your device into the dock connector.
4. Press the on the top of the unit or the remote to power on
Tango TRX.
5. Press the source button on the top of the unit or on the remote
until the iPod logo is illuminated as the source.
6. Press play on the on the unit or on the remote. Use the
controls on the unit or the included remote to adjust the
volume and iPod functions.
Note: The unit will charge your device while docked.
lIstenIng to Your DevIce wIrelesslY over
Bluetooth
To listen to your music over the Bluetooth wireless connection,
you need to pair your device with Tango TRX.
1. Make sure your device has Bluetooth capability.
2. Press the on the top of the unit or the remote to power on
Tango TRX.
3. Follow the instructions listed in the manual of your device to
turn on the Bluetooth functionality to pair your device with
the unit.
4. Pair your device with the unit by selecting Tango TRX from
your Bluetooth listings on your device or selecting yes. If
prompted, enter 0000 as the passcode.
5. Press the source button on the top of the unit or the remote
until the LED under the Bluetooth logo is illuminated as
the source.
6. Press play on your device and use the control dial on the unit
or the remote to adjust the volume.
7. Use your device or the remote (for iPod/iPhone only) to control
music functions.
Note: Once you have successfully paired your device with Tango TRX, you will not
need to repeat the above steps. For each use, ensure that the unit source is set to
Bluetooth and that Bluetooth is enabled on your device.
receIvIng a call whIle transmIttIng musIc
over Bluetooth
The music will automatically stop when the phone begins to
ring and the ringer will sound over the speakers. If you would
like to continue the call over Bluetooth using Tango TRX as a
speakerphone, answer the phone and select Tango TRX as the
phone source. Next, make sure you are close enough to the unit to
speak into the microphone which is located behind the center of
the speaker grill. Use the control dial on the unit or the remote to
adjust the volume.
3
1
2
4
1. Dock connector
2. Back support
3. Screw
4. AC power jack
5V 2.1A