MAGNETIC DRILL ITEM No. 45301 & 45302 OWNER'S MANUAL AND SAFETY INSTRUCTIONS SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY, OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT'S SERIAL NUMBER ON THE BACK OF THE MANUAL NEAR THE ASSEMBLY DIAGRAM (OR MONTH AND YEAR OF PURCHASE IF PRODUCT HAS NO NUMBER) FOR QUESTIONS PLEASE CALL OUR CUSTOMER SUPPORT: 909.628.
General Safety WARNING! Please read this instruction before using, and strictly follow the listed instructions below, to avoid electric shock, fire and other serious injury. 1. Do not use in the wet or humid environments. 2. Do not near flammable and explosive liquids, gases or dust. 3. Do not use on a power supply without a grounding device or surge protector, the outlet must be grounded reliably, to prevent electric shock when using. 4. Do not refit plug. 5.
BEFORE USE • Check the working area with the metal locator. be cautious of the inside cable, gas pipe, and water pipe. Before operating the machine, check supply voltage and general conditions, i.e. cable/cord damage. A machine with damaged cable must be returned or repaired prior to use. The machine is 110V, the wave motion can not surpass the 10%. • Set the handle lever into the handle hole and next tighten them. • Turn the handle lever and check the guide board to confirm it is moving freely.
Technical specification Item No. 45301 45302 Voltage 110V 110V Frequency 60HZ 60HZ Input power 1100W/10A 1400W/12.7A 700r/min 100-60r/min Twist drilling diameter 16mm 28mm Max depth of twist drilling 80mm 130mm 12-35mm 12-50mm Max depth of coring 40mm 70mm Max travel 150mm 180mm Magnetic adhesion boon 9000N 13500N I MT3 No load speed Coring drilling Diameter Spindle holder Accessories: Item No. Handle Item No.
Twist drill and core drill 1. While the power is on, the machine will be in standby mode. 2. . lnstall the cutter, then get the cutter point in the working position. 3.Turn on the switch for magnetic blocks to absorb the work pieces. 4. Turn on the motor switch, the motor should be spinning clockwise. 5. Rotate the speed-controller to choose the required speed for drilling holes. 6. Shake down the handle, get the cutter close to workpiece slowly.
D. lnstall the required drill and loosen the dial and tighten the top screws. Turn the rack so that the drill can align the holes and tighten the top screw. Rotate supporting bar. E. Open the drill control switch for the drilling process. (Note: The feed is generally 0.55mm/r, not too much force in order to prevent overload. F. When processing is complete, turn off the control switch and magnet control switch and pick up magnetic drill from work surface. Maintenance 1.
EXPLODED DRAWING Item No.
No.
LODED DRAWING Item N o ..
No.
EXPLODED DRAWING Item No.
No. Description Qty 1 Screw M5x30 4 2 Screw M5x14 2 10 3 Spring Washer5 4 Rear Cover 1 5 Stator bushing 1 6 Brush Holder 2 7 Carbon Brush 2 8 Spring 2 9 Cap of carbon brush 2 10 screw M4x8 4 11 Connecting spring 2 12 Stator 1 13 Screw M5x65 2 14 Bearing 629 1 15 Rotor 1 16 Housing 1 17 Anti-wind Ring 1 18 Bearing 6001 1 19 Bearing holder 1 20 Pin M6x6x12 1 21 Clutch Ring\20 1 22 Big Gear 1 23 Bearing\609 1 24 Compound Gear 1 25
EXPLODE DRAWING Item No.
Pos. No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Regulation Sleeve Screw M8x15 Shaft sleeve <1>18 Screw M6x12 Connect Nut Bellows joint rack Flat Pad Cablo sheath cable NutM4 Clutch Ring <1>18 Gear Shaft sleeve <1>22 Round pin M5x12 Up-down shaft Handle base Handle lever Cable mount screw\M4x8 Cord Clamp Label screw\M4x8 Label Scrow\M5x16 Left guide board Screw\M6x20 Spring Washer <1>6 Right guide board Screw\M8x2
SERVICE PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
