Water temperature in excess of 100° F (37.7° C) may be hazardous to your health. Prolonged immersion in hot water may induce hypothermia. Hypothermia occurs when the internal temperature of the body reaches a level several degrees above normal body temperature of 98.6° F (37° C.). Effects of hypothermia include: (1) Unawareness of impending danger. (2) Failure to perceive heat. (3) Failure to recognize the need to leave the spa. (4) Physical inability to exit the spa. (5) Fetal damage in pregnant women.
Hair Entanglement – When the hair tangles or knots in the drain cover, trapping the swimmer underwater. This hazard is present when the flow rating of the cover is too small for the pump or pumps. Limb Entrapment – When a limb is sucked or inserted into an opening resulting in a mechanical bind or swelling. This hazard is present when a drain cover is missing, broken, loose, cracked or not properly secured.
Brief Introduction This variable speed pump is designed to operate your swimming pool filtration system as well as your spa, waterfall, cleaner, heater, salt chlorine system and other water applications. Using the control panel, you can run your pump on one of three scheduled programs: 1. Regular mode: use three quick start buttons. ECO (default 1500RPM)/CLEAN( default 2400RPM)/BOOST( default 3250RPM), and then adjust the pump to run at the your preferred. 2. Mode 1: 16 hours for each clean cycle. 3.
Introduction of LED Control Panel ECO: Press to select and run on default speed 1500RPM, can be adjusted from 1000 to 2400RPM ! CLEAN: Press to select and run on default speed 2400RPM, can be adjusted from 2400 to 2850RPM " BOOST: Press to select and run on default speed 3250RPM, can be adjusted from 2850 to 3450RPM # STOP: Press to stop the pump. And the screen displays the present time $ MENU: Enter the pump menu if % & ' ( the pump is stopped MODE 1: To run the programmed 16 hours clean cycle.
Stopping and Running The Pump 3.1 Start The Pump 1) Make sure the pump is connected with power. When power is on, the display screen will display the time. 2) Press one of ECO/CLEAN/BOOST, the pump will run. The light on the corresponding program will shine. No matter what program you select, the pump will run on 2850RPM for 5 minutes to eliminate the air in the pump, so the impeller will not dry grind thus to cause leakage.
4. Pump Run Under MODE1/MODE2 4.2 How to Set and Change Specification of MODE1/MODE2 Indicator Light 1) Make sure STOP button is pressed before set up, and pump isECOECO not working. Press BOOST MENU, LED CLEAN BOOST CLEAN screen will display the current time (time will not count during set-up), use arrow buttons to adjust the time. LEFT and RIGHT to move the cursor one digit, and 1000-2400RPM UP and DOWN to increase or 2850-3450RPM 2400-2850RPM DEFAULT:1500 DEFAULT:3250 DEFAULT:2400 decrease one digit.
10
Control Panel Menu Structure 11
7. Parts Breakdown 1 647252772000 Strainer Cover 2 5431042080 Strainer Cover O-Ring 1 3 47252704001 Basket 1 4 47252703080 Strainer Housing 1 5 47252705080 Clip 1 6 5431029080 Strainer Housing O-Ring 1 7 5212016000 Screw ST5.
8. Performance Curve 9.Alert and Warnings The pump displays all alerts and warnings on the control panel. When an alarm or warning condition exists, the corresponding LED will shine and the error code will be displayed on the screen.All control panel buttons are disabled until the alarm or warning is acknowledged by press the ENTER button. Power off until the display off.
256 the water pump and observe the error. Please contact the supplier,if the error is still exist. 512 1024 0 4001 4002 4096 After power off, it will takes more than ten seconds to restart, as the internal energy storage elements need to be discharged. The pump may work abnormally,if the circuit board is restarted before the power is discharged.
