SKU: 76046 E248578 QSB-JH-450211 C US LISTED 26XZ ASSEMBLY 76046
1 6 8 9 10 11 13 14 15 CUSTOMER SERVICE 1
OUT IN 30’ X1
Attention danger Not connected Power up Observez Maintenance Connected Stop Clean Water Environment 3
1 NO 2 4
3 4 B A
Thank you for purchasing this product.Please read these instructions, and keep them for future reference. This tool is an electric pump. It is used for pumping water and other similar water applications. After opening the package, please ensure that the products are complete (if any). If the products are damaged or there is something missing, please do not use it and bring it back to your dealer. If you give this tool to another person, please give him this instruction manual. Safety Instruction 1.
Children are not allowed to wash or maintain equipment without supervision. 10.Liquid contamination may be caused by leakage of lubricating oil. 11.The water pump can be connected with a shock proof plug installed in accordance with the regulations. 12.Do not use pumps when there is someone in the water. 13.When cleaning and maintaining, please disconnect the water pump from the main power supply. 14.Please contact technical staff . 15.
Long enough and strong ropes should be attached to thehandle before the first use. When the pump is immersed into the liquid, the rope along with a handle can be used to balance the pump. Installation The equipment requires an area of at least 60x60cm. Depth of equipment immersed in technical parameters. When installing the equipment, make sure the open will not the suction opening will not be blocked by foreign objects to keep the equipment stable.
Connecting pressure pipe - screw the pressure pipe onto the pressure connector. All joint connections must be sealed with a threaded sealing stripe. -When using the hose, screw the right hose adapter into the pressure connector. -Secure the hose firmly to the hose adapter and secure it with a hose clamp. If it is used occasionally, please use a suitable pipe. A rigid pipe with a check valve is recommended for use in a fixed position. This can be done at the close of the machine to prevent liquid backflow.
In most cases, you will be able to troubleshoot problems easily by yourself. Before you contact us, please refer to the following table for technical support. This will help you save a lot of work and possible expenses. Error Reasons Errorshooting The pump 1.Unconnected power. 1.Check power supply. cannot start 1.Clean the inlet . No water 1.Inlet obstruction. 2.The pressure hose 2.Adjusting hose . is bent . Too small 1.Inlet obstruction. flow rate 2.
Clean the equipment from the outside. Flush with clean water. Use brush and detergent to remove stubborn pollution. Immerse the pump into a container with clean water, open it for running a while, and flush it in the pump. Attention: Before using the pump again, first "clean" to prevent any possible dirt residue which could affect the equipment operation. Storage If there is a risk of frost, remove equipment and accessories, and clean and store it a place protected from frost.
76046 115 V / 60 Hz Model Nominal voltage 1/3 HP IPX8 31 Ft Horsepower Protection type Max. supply height 2150 GPH Max. flow rate 1/5 INCH Max. Grain size Attention! Risk for equipment damage! The particle size mentioned cannot be used for simple gravel or stone, but suitable for soft, variability of particles or similar things which cannot put into the water pump.
13
0010 0020 0030 0040 0050 0060 0070 0080 0090 0101 0102 0103 0104 0110 0120 0130 0140 0150 0160 0170 0180 0190 0200 0210 0220 0230 0240 0250 0260 0270 0280 253001515 201003576 208000808 201006696 207000296 207000478 209000784 207000035 207000503 204000202 310000035 204000185 311000026 202000174 204000093 207000531 252000363 251000678 208000621 202000135 201003459 208001246 208000803 201005490 207000066 201002892 207000060 212000026 212000033 212000014 212000010 Power cord Output connector Oil plug Main pum
PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor have provided the parts list and assembly diagram in this manual for reference purposes only. They do not make any representation or warranty to the buyer that they are qualified to make repairs to the product or replace any parts of the product. In fact, the manufacturer and/or distributor expressly state that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer.
