50” WALL MOUNT ELECTRIC FIREPLACE WITH GLASS FIRESTONE ITEM: 95029 OWNER’S MANUAL AND SAFETY INSTRUCTIONS SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY, OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES.
IMPORTANT SAFETY INFORMATION GENERAL SAFETY WARNINGS Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
IMPORTANT SAFETY INFORMATION DO NOT use the fireplace if any part has been under water. DO NOT operate the fireplace with the glass panel removed, cracked or broken. Servicing should only be done while the fireplace is disconnected from the power outlet. Unplug fireplace if not being used for an extended period of time. DO NOT use outdoors. NEVER locate fireplace where it may fall into a bathtub or other water container.
FEATURES Description Add a dash of romance to your home with the warmth and mesmerizing color play of this Fire and Ice electric fireplace. Its LED lights and crystals simulate flames dancing on embers while electric coils heat the surrounding air. There’s no smoke, no chimney, and no need to build or tend this fire. It is always under your remote control - as bright and as warm as you please. Features Insert Dimension: 43.5” x 15.
ASSEMBLY Getting Started: Unpack the contents of the box Heater Wall fixing bracket and screws Remote control 1 x bracket and and 1 x bottom bracket 8 x 6x25mm top bracket; 2 x 4*8mm to fix tempered glass 2 x 4*8mm and 1 x 6x25mm to fix the bottom 1 instruction manual 1 bag of crystal embers , 1 x white board Wall Mount Instructions This appliance is designed to be fixed to a wall at a minimum height of 300mm and the minimum distance from the top of the heater to the ceiling should be 1000mm.
ASSEMBLY Remove the back panel from the heater first. See Fig 2 Fig. 2 Remove the two pieces of white screws on both sides on the heater. See Fig 3 Fig. 3 Drill holes with a #6 drill bit. Fix the wall bracket using the plug and 6x25mm screws provided. Carefully lift up the heater ensuring the top rear ledge of the heater engages with the wall bracket (see Fig. 4) and is sitting centrally. This process should be carried out by two people.
ASSEMBLY Peel off the white board’s protective film and put the crystal on the appliance. Fig. 5 Place the front glass over the front of the fire aligning the slots in the bracket at each side of the glass panel with the lugs on the sides of the fire. Two people are required for this operatin. See Fig. 6 Fig. 6 Fix the tempered glass with 2 pieces of 4x4*8mm screws provided. See Fig. 6 Fig.
ASSEMBLY Fasten two pieces of white screws of both sides. See Fig. 5 Fig. 5 The switches located at the center right hand side of the fire. The standby switch must be switched on first. Wall Insert Instructions Take the glass from the heater first then gently put the heater to the cut hole. This is a two person operation. See Fig. 1 Fig. 2 For optimum wiewing, mark the left and right screws. Fixing positions on the wall in accordance with the appliance’s holes. See Fig. 2 Fig.
ASSEMBLY Place the front glass surround over the front of the aligning slots in each bracket at each side of the glass panel with the lugs on the sides of the heater. See. Fig. 4 Take the glass from the heater first then gently put the heater to the cut hole. This is a two person operation. See Fig. 1 Fig. 4 Fix the tempered glass with 2 of the 4*8mm screws as provided. Fig.
OPERATION The heater can be operated either by the switches located in the top right side of the fireplace, or by the supplied remote control. Control Panel Access The Standby switch at the center right hand side of the foreplace must be first switched on. It takes time for the receiver to respond to the transmitter. DO NOT press the buttons more than once within two seconds for correct operation. Press the ON/OFF button on the remote once, this turns the fireplace fire effect on and off.
MAINTENANCE The remote control requires one 3V CR2025 Lithium Cell Battery (included). Remove the protective film between the battery and the contacts in order to operate. See Fig 6 & 7 Replace the Remote Control Battery When the remote control stops operating or it’s range is reduced, it is time to replace the batteries. 1. The battery compartment is located on the back end of the remote. 2. Press and slide the battery door open and remove the old battery. 3.
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.