STAINLESS STEEL PORTABLE TUMBLE DRYER ITEM: 99816 OWNER’S MANUAL AND SAFETY INSTRUCTIONS SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY, OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT’S SERIAL NUMBER ON THE BACK OF THE MANUAL NEAR THE ASSEMBLY DIAGRAM (OR MONTH AND YEAR OF PURCHASE IF PRODUCT HAS NO NUMBER) FOR QUESTIONS PLEASE CALL OUR CUSTOMER SUPPORT: 909.628.
IMPORTANT SAFETY INFORMATION GENERAL SAFETY WARNINGS Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in fire, electric shock and/or serious injury. Save all warnings and instructions for future reference. SAFETY The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur.
IMPORTANT SAFETY INFORMATION DO NOT place the dryer on horizontal ground. DO NOT place on the carpet as this will block the intake. There should be at least 10cm between the dryer and the walls. DO NOT wash directly with water, thinner, gasoline or alcohol. DO NOT use a spray cleaner to clean the interior of the dryer, clean with a damp cloth instead. Remove any residue before drying the next load. This product in not intended for outdoor use.
FEATURES AND SPECIFICATIONS FEATURES Lightweight Portable Great for apartments, condos and lofts See-through window Wall mounting kit included Features auto dry and timed settings Coordinates great with small washers Can be plugged into any 110V outlet Dimensions: 27.6” H x 23.6” W x 17.
PARTS DIAGRAM DOOR GASKET DOOR DRUM AIR INTAKE SHROUD WINDOW TIME SELECTOR KNOB HEAT SELECTOR KNOB EXHAUST VENT CASING BACK COVER 4
INSTALLATION BEFORE USING YOUR APPLIANCE Check to make sure you have all the parts necessary for operation. Allow at least 5 inches of space between the sides of the appliance. Put laundry into the dryer evenly. Uneven laundry may cause noise and vibration. Before drying, check all pockets. Foreign objects can damage the machine. Make sure the appliance is on a flat, level surface at all times. To wall mount this appliance, use the included wall mount kit.
INSTALLATION 4. Align hanging hooks and fasten screws tightly. 5. Install exhaust pipe as per Fig. 3 6. Using 3x16mm screws (provided) to fix the outlet in place firmly. 7. Using 4x12mm screws to fix the 2 wall hanging bracket. Fig. 4 8. With assistance, mount dryer on wall bracket. Fig. 5 The appliance shall not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space or a concealed space of a building. Only rigid or flexible metal duct shall be used for exhausting.
INSTALLATION AND OPERATION ELECTRICAL CONNECTION: This appliance must be grounded. In the event of an electrical short circuit, the grounding plug reduces the risk of electric shock by providing an escape wire for electric current. This appliance is equipped with a power cord that has a grounding wire with a grounding plug. The plug must be plugged into an electrical outlet that is properly installed and grounded.
OPERATION CONTROL PANEL FUNCTIONS: HEAT SELECTOR BUTTON: Select “High Heat” for items that are particularly bulky or large quantities. Select “Low Heat” for delicate items such as silk, nylon etc. DRYING PROGRAM SELECTOR: There are five drying combinations available: cool, Anti-wrinkle, Warm, Hot and Dry. DRYING TIME REFERENCE: ** LOAD WEIGHTS AND DRYING TIMES ARE APPROXIMATE ** SORTING FABRICS: For best results, clothes should be sorted properly.
OPERATION FABRIC CARE CHART: CLEANING THE EXTERIOR: Wipe the dryer surfaces, including the control panel with a soft cloth and non-abrasive household detergent. UNPLUG THE POWER CORD PRIOR TO ANY CLEANING: Removing the lint filters, remove by pulling outward using the four grip holes in the filter assembly.
MAINTENANCE The filter assembly consists of three parts. A. Exhaust Vent Shroud B. Lint Filter C. Exhaust Filter Separate each of the above parts and clean the individual pieces using a soft brush or vacuum cleaner. DO NOT damage the filters. Separate each of the above parts and clean the individual pieces using a soft brush or vacuum cleaner. DO NOT damage the filters. CLEANING THE AIR INTAKE : Removing the Air Intake Filter: Remove by pulling outward holding the filter housing by the top and bottom.
WARRANTY PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.