SHENZHEN FZONE TECHNOLOGY CO., LTD. 2nd floor, Building 12, Xicheng Industrial Area, Xixiang Town, Baoan District, Shenzhen Guangdong China. 518101 E-mail: nancy@xviveaudio.
MANUAL MICROPHONE WIRELESS SYSTEM
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK: DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTSINSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. 01 CERTIFICATION This Class B digital apparatus complies with Canadian ICES-003. Radio Approvals: FCC Part 15.249, FCC Part 15 B, RSS-210 (Canada), EN 300 440 (Europe), EN 301.
FCC CERTIFICATION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. WARNING: Changes or modifications not expressly approved in writing by Xvive may void the users authority to operate this equipment.
IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THESE INSTRUCTIONS IN A SAFE PLACE WARNING: BEFORE USING YOUR XVIVE U3 MICROPHONE WIRELESS SYSTEM, CAREFULLY READ THE OPERATING INSTRUCTIONS. 1. Observe all instructions carefully in the U3 manual. 2. Do not to perform service operations beyond those described in the U3 manual.
PRODUCT INTRODUCTION • 2.4Ghz band is optimal for microphone wireless, approved for use in Europe, South America, Asia and Australia. • Less than 5ms Latency, Simultaneous broadcasts on 6 channels.
QUICK START 1. Plug the Transmitter into the Dynamic Microphone 05 2. Plug the Receiver into the Mixer.
QUICK START Hello! 3. Turn on the Transmitter and the receiver and check the Channel. 4. After connecting successfully, the LED lights on receiver will stay on. 5. Check the connection by talking through the microphone.
BASIC OPERATION TRANSMITTER 1 2 2 Mic In – XLR microphone input jack Spring - Circumferential ground spring providing an accurate connection to the mating shell 1 3 Mic Lock – secures transmitter to the microphone 4 Input level switch – MIC = 0dB input; 5 Power switch – switches unit on/o� 6 Channel status LED - indicates selected channel 7 Channel switch - selects Channels 1-6 8 8 USB charging port 9 9 3 LINE = -10dB input 4 5 6 7 10 Power status LED - indicates power status: Led off
BASIC OPERATION RECEIVER 1 1 XLR OUT - XLR microphone input jack 2 Power switch – switches the unit on and o� 3 Channel status LED - indicates selected channel 4 Channel switch - selects Channels 1-6 5 USB Port – For charging the battery 6 RF Status LED – ON = Transmitter is on and link is established 2 Flashing = Signal connection interference 3 4 5 6 OFF = Transmitter o� or unlinked 7 Power status Led - indicates power status.
SPECIFICATIONS U3 MICROPHONE WIRELESS SYSTEM 09 Tuning Bandwidth 2400 – 2483.5MHz Working Range Indoors 90ft Actual range depends on RF signal absorption, reflection and interference. Audio Frequency Response 20Hz – 20KHz(-3dB). Dependent on microphone type or Input signal. Dynamic Range 110dB Battery Life Up to 5 hours RF Sensitivity -88dBm Total Harmonic distortion 0.2% RF Output Power 10 mW E.I.R.P. max Operating Temperature Range -18℃ to 57℃.
TRANSMITTER RECEIVER Dimensions 31 x 29 x 98 mm 31 x 29 x 98 mm Weight 93g 92g Housing Molded Plastic and cast Metal Molded plastic and cast metal Battery 3.7V Rechargeable Li-lon, 860mA 3.7V Rechargeable Li-lon, 860mA Impedance Input 15KΩ(1KHZ) Output 470Ω(1KHZ) Audio Input Connector Balanced XLR male input Audio Output Connector Maximum Input Level Balanced XLR Female Output Mic mode: 2.8Vp-p Line mode: 7Vp-p Maximum Output Level 2.
BATTERIES AND CHARGING CHARGING TIMES BATTERY LIFE 0:15 30 min 0:30 1 hours 1:00 2 hours 2:30 5 hours * Always store U3 at room temperature * When storing the unit, please check the battery state regularly and charge if necessary. Connect Power Connect to the socket Note: In an emergency, power can be supplied via a USB wall adapter however, the battery life will be reduced.
2.4 GHz SPECTRUM OVERVIEW AND INTERFERENCE U3 operates within the 2.4GHz ISM band which is utilized by Wi-Fi, Bluetooth, and other wireless devices. 2.4Ghz is an open band and, as such, does not require a license to be used worldwide. Tips and Methods to Improve Wireless System Performance 1) Keep more than 3 meteres distance between U3 Receiver unit and other WiFi transmitters such as routers. 2) Change channels to avoid interference with other WiFi products.
TROUBLESHOOTING ISSUE SOLUTION • Check that the U3 Receiver's blue RF LED is lit. No Sound • Check that the microphone is turned on and receiving signal from the U3 Transmitter • Check that the power switch is turned on for both the Transmitter and the Receiver. • Ensure that the U3 Transmitter and Receiver are on the same channel. • Adjust the gain mode to “Line” or “Mic” Distortion or Faint Sound • Adjust the output signal from the transmitting device.
APPLICATION SCENE Live Sound Mixers Dynamic Microphone Portable PA Systems DI Or XLR Output Gear Recorders MICROPHONE WIRELESS SYSTEM 14
