Owner's manual
Table Of Contents
- 1 Overview
- 2 Safety instructions
- 3 Commissioning
- 4 Operation
- 4.1 Switching on or off the photometer
- 4.2 General operating principles
- 4.3 Photometer settings and system administration
- 4.4 Zero adjustment
- 4.5 Measuring in Concentration mode
- 4.5.1 Measuring cell tests with barcode
- 4.5.2 Measuring reagent tests with AutoSelector
- 4.5.3 Measuring reagent-free tests and user-defined methods
- 4.5.4 Exceeding the upper or lower limits of the measuring range
- 4.5.5 Selecting a method manually
- 4.5.6 Settings for Concentration mode
- 4.5.7 Measuring diluted samples
- 4.5.8 Sample blank value
- 4.5.9 Reagent blank value
- 4.5.10 Automatic Turbidity correction
- 4.5.11 Programming / modifying user-defined methods
- 4.5.12 The IQ LabLink procedure
- 4.6 Measuring the Absorbance / % Transmission
- 4.7 Multi wavelengths methods
- 4.8 Spectrum
- 4.9 Kinetics
- 4.10 Timer
- 4.11 Memory
- 4.11.1 Overview
- 4.11.2 Instructions on using USB memory devices
- 4.11.3 Measurement datasets
- 4.11.4 Saving measurement datasets manually
- 4.11.5 Saving measurement datasets automatically
- 4.11.6 Displaying measurement data memory
- 4.11.7 Filtering measurement datasets
- 4.11.8 Inverting filters
- 4.11.9 Erasing stored measurement datasets
- 4.12 Copying files
- 4.13 Transmitting data
- 4.14 Analytical quality assurance (AQA)
- 4.15 User management
- 4.16 Reset
- 4.17 Photometer information ([Info])
- 4.18 Lamp counter
- 4.19 Software and methods update
- 5 Maintenance and cleaning
- 6 What to do if ...
- 7 Technical data
- 8 Accessories and options
- Appendix
photoLab
®
6100 VIS Operation
149
ba75847e01 08/2009
4.19.3 Software update "Chinese character set"
If you want to display on your photometer the languages, "Simplified
Chinese/中文" or "Traditional Chinese/繁體中文", a Chinese character set is
required to display the Chinese characters. This character set is not
preinstalled.
You can install on your photometer this character set with the software
update, "Chinese character set". It permanently requires 2 MB free storage
on your photometer.
Note
The installation of this character set is not reversible.
Therefore, if you do not intend to set the photometer language to Chinese,
we recommend not to install the update, "Chinese character set".
Before the update Before carrying out the software update, "Chinese character set", make sure
the current software version is installed on the photometer.
The newest software version is available from your instrument manufacturer
as an update on the Internet. Download this update and install it before
starting the software update, "Chinese character set".
Requirements The update by means of a USB memory device requires:
z at least 2 MB free storage on the photometer.
The update by means of a PC requires:
z at least 4 MB free storage on the photometer.
Note
You can view the currently available free storage on the photometer in the
Info menu.
If less free storage is available than required for the update, the update is not
possible.
You can erase measurement data from the photometer until enough free
storage is available.
Update Carry out this update in the same way as a software and methods update.
The update process takes approx. two minutes. Subsequently, the
photometer switches itself off.