User manual

V1.1
S. 26
Die Anweisungen zur Problemlösung können Ihnen bei der Behebung von Problemen helfen. Falls sich Probleme
nicht beheben lassen, wenden Sie sich bitte an den Kundendienst.
Kundendienst:http://support.xyzprinting.com
Technischer Support (US):[e-mail]
Technischer Support (EU):[e-mail]
Andere Regionen:[e-mail]
Kapitel 10 – Einzelheiten zum Support
Servicecode Symptom Maßnahme Servicecode Symptom Maßnahme
0 0 1 0
Heizproblem der
Druckplatte
Verbindungen prüfen, Drucker
neu starten.
0 0 3 2
Unnormale Bewegung
der Z-Achse
Motor-/Sensorverbindungen
prüfen. Sensorposition prüfen.
0 0 1 1
Heizproblem
Extruder 1
Verbindungen prüfen, Drucker
neu starten.
0 0 4 0
Fehler interner
Speicher
Prüfen, ob SD-Karte richtig
eingesetzt ist.
0 0 1 3
Heizproblem der
Druckplatte
Verbindungen prüfen, Drucker
neu starten.
0 0 5 0
Speicherfehler Drucker neu starten.
0 0 1 4
Heizproblem
Extruder 1
Verbindungen prüfen, Drucker
neu starten.
0 0 6 0
Interner
Kommunikationsfehler
Drucker neu starten.
0 0 3 0
Unnormale
Bewegung der
X-Achse
Motor-/Sensorverbindungen
prüfen. Sensorposition prüfen.
0 2 0 1
Verbindungsfehler
zwischen PC und
Drucker
PC erneut an Drucker anschließen
oder Kabel zwischen Drucker und
PC im Betrieb anschließen.
0 0 3 1
Unnormale
Bewegung der
Y-Achse
Motor-/Sensorverbindungen
prüfen. Sensorposition prüfen.
Fehlermeldung Maßnahme
Drucker ist mit einer anderen
Aufgabe beschäftigt
Nach Abschluss aller Aufgaben erneut versuchen. Zudem die am Druckerdisplay angezeigten
Informationen prüfen.
Aktualisierung der Drucker-
Firmware fehlgeschlagen
Internetkonnektivität prüfen/Firmware-Aktualisierung später erneut versuchen.
Filament 1 verklemmt Cassette 1 entladen und neu laden, Düse reinigen.
Ladeproblem Filament 1 Cassette 1 entladen und neu laden.
Installationsproblem Filament 1 Installieren Sie Cassette 1 neu oder wählen Sie eine neue Cassette.
Obere Abdeckung offen Obere Abdeckung schließen.
Filament 1-Stand gering: Noch 30 m Cassette 1 bei Bedarf ersetzen.
Filament 1-Stand gering: Noch 5 m Cassette 1 sofort ersetzen.
Federal Communications Commission (FCC) Statement
You are cautioned that changes or modications not expressly approved by the part responsible for compliance could void the user’s authority
to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
XYZprinting is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by
unauthorized changes or modications to this equipment. Unauthorized changes or modications could void the user's authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC
RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter
must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the
no-collocation statement.