da Vinci Jr.1.0 Pro May 2016 da Vinci Junior 1.0 Pro 3D Printer da Vinci Jr.1.
da Vinci Jr.1.0 Pro May 2016 The purpose of this user manual is to help users understand and use the da Vinci Jr. 1.0 Pro 3D printer correctly. It contains the operating instructions, maintenance information and application skills of the da Vinci Jr. 1.0 Pro 3D printer. To learn more about the latest news of the da Vinci Jr. 1.0 Pro 3D printer, please contact local dealers or visit the official website of XYZprinting: http://www.xyzprinting.
da Vinci Jr.1.
da Vinci Jr.1.0 Pro May 2016 1 Open the box and remove the 2 Remove the plastic bag and accessories and cushions. 3 Remove all fixing tapes and the cushion between print bed and extruder module. 6 Be sure to remove the fixing tapes at the back of the print bed. the tapes. 4 Be sure to remove the fixing cushion from the axis. 7 Be sure to remove the paper cardboard near the Y-axis.
da Vinci Jr.1.0 Pro May 2016 Note: Please follow these steps and ensure that the guide tube is properly installed before starting the "LOAD FILAMENT" function. Failure to install the guide tube may disrupt filament feed. Install the filament guide tube 1 Direct the guide tube from the tube movement area out of the machine and then insert the other end of the filament tube into the feed module tube port. 2 Ensure that the guide tube has been tightly inserted into the feeding hole.
da Vinci Jr.1.0 Pro May 2016 CHANGE SPOOL 1 First retrieve filament spool to install the filament spool axle ring. 3 Install the sensor chip. Please pay special attention to the position of the installation holes on the chip. 2 Take out and separate the filament spool axle ring into its two components.
da Vinci Jr.1.0 Pro May 2016 LOAD FILAMENT Then load filament using the control panel on the printer… DA VINCI Jr. Pro UTILITIES SETTINGS INFO UTILITIES CHANGE SPOOL HOME AXES JOG MODE USE XYZPRINTING SPOOL? YES NO CHANGE SPOOL LOAD FILAMENT UNLOAD FILAMENT 1 Select "UTILITIES" > "CHANGE SPOOL" > "LOAD FILAMENT" > "YES".
da Vinci Jr.1.0 Pro May 2016 CALIBRATE Calibration is enabled for this new extruder module. Please update printer firmware via XYZware before using the new extruder. 1. Active print bed calibration by selecting “UTILITIES”>”CALIBRATE”>”YES” on the screen. 2. Press the detection head on the right side of the print head according to the instruction of screen message, followed by pressing OK. PRESS SWITCH NEXT TO EXTRUDER [OK] TO CONTINUE 3. Wait for detecting. 4-1A.
da Vinci Jr.1.0 Pro May 2016 HOME AXES “HOME AXES” moves the extruder to the lower left corner. To home axes: home axes are you sure NO YES Select “YES” to proceed. JOG MODE “JOG MODE” is used to manually move the extruder and the print bed. To move the extruder: jog mode x-axis y-axis z-axis x-axis ok exit － ▲ ■ 001mM ▲ ＋ 010mm 020mm 1.Select “X-AXIS” (to move right and left) and "Z-AXIS" (to move up and down). Execute "Home Axes" function first to move "Z-AXIS".
da Vinci Jr.1.0 Pro May 2016 Note: The machine can be turned off only when the cooling fan of the print head stops running after the print is completed. Turning off the power directly may clog the print head. References: Please refer to UTILITIES>CLEAN NOZZLE to remove the blocks out of the print head. This section describes how to clean the feed module. After heavy use of printer, if feeding of material becomes difficult or impossible, please follow these steps. Preparation of Tools A.
da Vinci Jr.1.0 Pro May 2016 CLEAN NOZZLE A.Feeding Path Cleaning Pin B.Cleaner Wire Over time, carbon deposits or filament dust buildup in the nozzle may decrease its performance. It is advised to clean the nozzle after every 25 hours of printing. Also, if the print bed calibration shows “ERR” or if there is any residue on your prints, you may try to clean the nozzle. To clean the nozzle: CLEAN NOZZLE READY FOR CLEAN CLEAN NOZZLE ARE YOU SURE ? NO YES 1.Select "YES" to begin. [ OK ] TO RETURN 2.
da Vinci Jr.1.0 Pro May 2016 Install Compatible filament 1 If you’re using third party filaments, please secure the filament using the holder. 2 Load the filament from the back of the printer. 3 In the printer, insert the filament into the feed port. Open the release arm so that the front tip of the filament can be properly inserted into the feed module. 4 Load the filament function of the printer function.
da Vinci Jr.1.0 Pro May 2016 da Vinci Junior 1.0P 3D Printer Model Name Dimensions Weight Display Language Connection method Print Technology Build Volume Print resolution Print module Nozzle diameter Filament diameter Printed temperature Files supported Operating system Hardware requirement da Vinci Junior 1.0P 3D Printer 16.54 x 16.93 x 14.96 inches （420 x 430 x 380 mm） 26.46 lbs (12kg) 2.6” FSTN LCM Multi language USB Wire / SD Card FFF (Fused Filament Fabrication) 5.9 x 5.9 x 5.
