da Vinci Jr.1.0 Ver.1 March 2015 da Vinci Junior 1.0w 3D Printer da Vinci Jr.1.
da Vinci Jr.1.0 Ver.1 March 2015 The purpose of this user manual is to help users understand and use the da Vinci Junior 1.0w 3D printer correctly. It contains the operating instructions, maintenance information and application skills of the da Vinci Junior 1.0w 3D printer. To learn more about the latest news of the da Vinci Junior 1.0w 3D printer, please contact local dealers or visit the official website of XYZprinting: http://www.xyzprinting.
da Vinci Jr.1.0 Ver.
da Vinci Jr.1.0 Ver.1 March 2015 1 Open the box and remove the accessories and cushions. 3 Raise the paper cardboard slightly upwards so that the paper cardboard is detached from the styrofoam slot at the bottom. 2 Remove the plastic bag and the tapes. 4 Remove the securing cardboard of the printing head and then remove the entire cardboard. You may push the print nozzle towards the back out of the cardboard and bend the securing cardboard downwards for an easy removal.
da Vinci Jr.1.0 Ver.1 March 2015 Note: Please follow these steps and ensure that the guide tube is properly installed before starting the "LOAD FILAMENT" function. Failure to install the guide tube may disrupt filament feed. ．Guide tude 1 Take out the guide tube and plug in one end of the tube into the filament feed port on the printing module. 3 Direct the guide tube from the tube movement area out of the machine and then insert the other end of the filament tube into the feed module tube port.
da Vinci Jr.1.0 Ver.1 March 2015 CHANGE SPOOL 1 First retrieve filament spool to install the filament spool axle ring. 3 Install the sensor chip. Please pay special attention to position of the installation holes on the chip. 2 Take out and separate the filament spool axle ring into its two components.
da Vinci Jr.1.0 Ver.1 March 2015 LOAD FILAMENT Then load filament using the control panel on the printer… DA VINCI Jr. 1w UTILITIES SETTINGS INFO CHANGE SPOOL LOAD FILAMENT UNLOAD FILAMENT UTILITIES CHANGE SPOOL HOME AXES JOG MODE 1 Select "UTILITIES" > "CHANGE SPOOL" > "LOAD FILAMENT". LOAD FILAMENT EXTRUDER HEATING TEMPERATURE 210 ∘ C PLEASE WAIT CHECK FILAMENT OUT FROM NOZZLE [ ＜ ] TO RETRY [ OK ] TO RETURN LOADING PLEASE WAIT 2 Wait for the extruder to heat up and load filament.
da Vinci Jr.1.0 Ver.1 March 2015 The troubleshooting instruction may guide you to fix the problem. If any error persists, please contact customer service center for support. When an error occurs, please refer to the service code shown on the printer and/or in the software, and check the suggestion below for troubleshooting. Technical Support Website: http://support.xyzprinting.com Email: US - supportus@xyzprinting.com EU - supporteu@xyzprinting.com Other regions - support@xyzprinting.
da Vinci Jr.1.0 Ver.1 March 2015 da Vinci Jr.1.0w 3D Printer Model Name Dimensions Weight Display Language Connection method Print Technology Build Volume Print resolution Print module Nozzle diameter Filament diameter Files supported Operating system Hardware requirement da Vinci Junior 1.0w 3D Printer 16.54 x 14.96 x 16.93 inches （420 x 430 x 380 mm） 26.46 lbs (12kg) 2.6” FSTN LCM English / Japanese USB Wire / SD Card FFF (Fused Filament Fabrication) 5.9 x 5.9 x 5.
da Vinci Jr.1.0 Ver.1 March 2015 About the da Vinci junior series 3D printer The da Vinci junior series 3D printer (da Vinci Jr.) is a brand new product from XYZprinting that is dedicated to the 3D printer market.
da Vinci Jr.1.0 Ver.1 March 2015 Button instructions After switching on the printer's power, the user may use the display panel at the front of the printer to understand its status and usage data. The functional buttons on the right allow the user to perform the relevant operations.
da Vinci Jr.1.0 Ver.1 March 2015 Home Menu Top Menu Sub Menu Page P6 CHANGE SPOOL LOAD FILAMENT P7 UNLOAD FILAMENT P7 HOME AXES P13 JOG MODE P13 BUILD FROM CARD P13 CLEAN NOZZLE P14 Z OFFSET P14 BUZZER P15 LANGUAGE P15 ENERGY SAVE P15 RESTORE DEFAULT P15 STATISTICS P16 SYSTEM VERSION P16 SPOOL STATS P16 HELP P16 UTILITIES SETTINGS INFO MONITOR MODE P16 The map above shows the functions your may access with the control panel on the printer.
da Vinci Jr.1.0 Ver.1 March 2015 HOME AXES “HOME AXES” moves the extruder to the right back corner, and the print bed to the top. To home axes: home axes are you sure NO YES Select “YES” to proceed. JOG MODE “JOG MODE” is used to manually move the extruder and the print bed. To move the extruder: jog mode x-axis y-axis z-axis 1.Select “X-AXIS” (to move right and left) or “Y-AXIS” (to move backwards and forwards). x-axis ok exit － ▲ ■ 001mM ▲ ＋ 010mm 020mm 2.
da Vinci Jr.1.0 Ver.1 March 2015 CLEAN NOZZLE Over time, carbon deposits or filament dust buildup in the nozzle may decrease its performance. It is advised to clean the nozzle after every 25-hour of printing. Also, when you find the result of print bed calibration shows “ERR” or any residue on your prints, you may try to clean the nozzle. To clean the nozzle: clean nozzle are you sure NO YES 1.Select "YES" to begin. 2.
da Vinci Jr.1.0 Ver.1 March 2015 BUZZER When the buzzer is turned on, the printer will output an audible signal when a button is pressed, print job is finished, or issue is detected. Buzzer is turned on by default. To switch off the buzzer: buzzer off on on Select “OFF” and press “OK” to change the setting. LANGUAGE You may switch the display language on the printer between English and Japanese. The default lanague is English.
da Vinci Jr.1.0 Ver.1 March 2015 STATISTICS In “STATISTICS”, you can check the accumulated print time and last print time. statistics lifetime 00006h last time 00h34m ok to return SYSTEM VERSION Firmware version is shown here. For stable printing performance, it is advised to keep the firmware up to date. To check for firmware updates, please go to XYZscan/XYZware. system version 1.1.
da Vinci Jr.1.0 Other Information Ver.1 March 2015 1. This product is guaranteed for specific period from the purchase date against any breakdown within the scope of proper and reasonable usage of their product as defined by XYZ printing. Presentation of warranty card with the product will ensure free service and repair of inherent faults in the product within the warranty period.
da Vinci Jr.1.0 Ver.1 March 2015 Warning ● Do not let children operate this device without adult supervision. Electric shock hazard. Moving pars can cause serious injury. ● Do not place the printer on an unbalanced or unstable surface. Printer may fall or tumble causing harm and/or injury. Printer may fall or tumble causing harm and/or injury. ● Do not place any objects on top of the printer. Liquids and objects that fall into the printer can lead to printer damage or safety risks.
