PartPro150 xP 3D Printer (Model No. 6L20X) Operation Manual Please always refer to the updated version of PartPro150 xP operation manual https://pro.xyzprinting.com/ For safe and correct use, be sure to read the Safety Precautions before using the machine. Version 1.
Version 1.0 PartPro150 xP Operation Manual Document History Date 2019-12 Description Initial Release Version 1.
Version 1.0 PartPro150 xP Operation Manual INTRODUCTION The PartPro150 xP is a stereolithography 3D printer that uses UV laser to cure photosensitive resins. During the printing process, the UV laser traces the cross-section patterns on the surface of the resin layer by layer. The nature of laser and UV resin presents parts with fine details and smooth surface finish. DISCLAIMER This manual is designed for users to understand how to use the PartPro150 xP printer in a safe manner.
Version 1.0 PartPro150 xP Operation Manual TABLE OF CONTENTS INTRODUCTION ............................................................................................................................................... 2 DISCLAIMER..................................................................................................................................................... 2 INTENDED USE ....................................................................................................................
Version 1.0 PartPro150 xP Operation Manual OVERALL WORKFLOW ............................................................................................................................................18 3. OPERATING THE PRINTER ........................................................................................................................... 19 PRINT MENU ..................................................................................................................................................
Version 1.0 PartPro150 xP Operation Manual PREFERENCE SETTINGS ...........................................................................................................................................36 Display language .................................................................................................................................................37 Display unit .................................................................................................................................
Version 1.0 PartPro150 xP Operation Manual SAFETY AND COMPLIANCE IMPORTANT SAFETY PRECAUTIONS Please read through all sections especially the safety guide carefully before unpacking, assembling, operating, replacing, and removing any part of this product. Please also comply with the instructions of relevant safety precautions. 1 2 Label Safety Notic WARNING - CLASS 3B LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO THE BEAM. 1 Keep the covers securely closed during printing.
Version 1.0 PartPro150 xP Operation Manual SAFETY AND REGULATION Please carefully read this notice, all safety precautions, and comply with safety rules when using, operating, unboxing this product, replacing or removing any components, or maintaining this product. For more information related to the PartPro150 xP 3D Printer or XYZprinting, visit the official website (https://pro.xyzprinting.com/) or contact a sales representative.
Version 1.0 PartPro150 xP Operation Manual NOTICES ON HANDLING / RECYCLING /DISPOSAL PRINTING MATERIALS Keep the storage of the printing materials locked up and out of the reach of children. Always wear the chemical-resistant gloves to prevent direct contacting with printing materials. Wasted resin can be pulled into plastic bag and cured under sunlight or UV light source. Cured resin can be discarded as office waste. Be careful not to spill the resin material.
Version 1.0 PartPro150 xP Operation Manual 1. UNPACKING AND INSTALLATIONS UNPACKING Unpack the product follow instructions closely. Damage to parts may result if the procedure is not followed. Keep original packaging material in the event of sending the unit for service or repair. 1. Remove all external packing materials, plastic bag and tapes on the covers. 2. Get the power adapter and the power cord from the accessory box in the package. 3.
Version 1.0 PartPro150 xP Operation Manual 7. Move up the platform rack by tapping the following options on the screen: Error message 2009 will show up during the setup, since the tank is not yet installed. Simply tap [PROCEED] to close the message at this stage. 8. Complete the hardware installations. Tap [>] on the screen after installing each item. Refer to p.6 to p.8 for detailed instructions on the installation. •Install the platform. •Install the resin tank. •Install the wiper.
Version 1.0 PartPro150 xP Operation Manual HARDWARE INSTALLATION Complete the following installation after unpacking the product. Be sure to follow the installation instructions closely. Damage to parts may result if any item is installed incorrectly. The printer is ready for production after completing the following installation. To install the platform: 1. Open the front cover. 2. Make sure the bolt handle connecting to Z-axis is loosen. 3. Hold the platform and mount it onto the platform rack.
Version 1.0 PartPro150 xP Operation Manual To install the resin tank and the wiper: 1. Open the front cover. 2. Unpack the resin tank from the package and remove the tank lid 3. Insert the tank into the tank slot. Push all the way until reaching the end. 4. Loosen and remove the fixing bolt over the wiper shaft. 5. Mount the wiper on the wiper shaft. 6. Insert the fixing bolt to the wiper raft and fasten the bolt.
Version 1.0 PartPro150 xP Operation Manual To install the Resin Bottle: 1. Shake the resin bottle well to ensure even color. For the material with dense pigment, you may need to tilt the bottle at 45° for 5 minutes, and then shake the bottle for around 5 minutes. 2. Assemble the nozzle cap and the inner tube. 3. Replace the sealing cap with the assembled nozzle cap. 5. Insert the resin bottle into the bottle slot. 6. Attach the exhaust tube to the thin nozzle.
Version 1.0 PartPro150 xP Operation Manual To check the resin information The printer detects the information of the resin installed through the ID tag at the bottom of the resin cartridge. Printing is not allowed when the cartridge is empty or when the material installed mismatch the resin selected while exporting. [Note: resin level is not available on the printer screen for the beta test. It will be added soon.
Version 1.0 PartPro150 xP Operation Manual SOFTWARE INSTALLATION “XYZprint AMUV” should be installed on the service PC for preparing the files for production. 1. To install the software: Double-click on the installer [XYZware_***.exe]. 2. Click [Next >] to initial the installation. 3. Review the license agreement, select [I accept the agreement] if appropriate, and press [Next >]. 4. Check if the default Installation folder is accepted, and click [Next>]. 5.
Version 1.0 PartPro150 xP Operation Manual 2. PRODUCT OVERVIEW APPEARANCE Front View - Exterior Component Rear View Description Front Cover Open this cover to take out printed model or perform regular maintenance. Keep the front cover securely closed during printing. Side Cover Access the resin bottle through the side cover. Touch Panel Contains a screen and keys for machine control.
Version 1.0 PartPro150 xP Operation Manual ACCESSORIES LIST Item Name Image Quantity Packing Location Description Resin Tank 1 pc The resin tank holds the resins for printing. ② Wiper 1 pc For wiping away the debris in the resin in the tank and for stirring the resin to ensure the evenness of temperature and color. ① Platform 1 pc Resin gets cured on the platform when exposed to laser light. ③ Rinse Bucket 1 pc Use the rinse bucket to wash the printed parts in alcohol.
Version 1.0 PartPro150 xP Operation Manual INSTALLATION SUGGESTIONS Installation Environments Make sure the installation site follows below conditions: Power requirements: AC 100~240V 50/60Hz 60W Ambient temperature: 20-30°C (68-86°F) Ambient humidity: 40-80% RH non-condensing Optimal Placement Follow below guidelines when positioning the printer: Place the printer on a leveled and solid surface, or resin level detection may be inaccurate.
Version 1.0 PartPro150 xP Operation Manual SPECIFICATIONS General Technology SL (Stererolithography) Light Source UV Laser λ 405nm Maximum Build Area (W x D x H) 150 x 150 x 200 mm (5.9 x 5.9 x 7.9 inch) XY-axis Resolution 130 microns Z-axis Resolution 25 / 50/ 100 / 200* microns (*Material dependent ) Connectivity USB Wire/ WiFi / Ethernet Product Dimensions (W x D x H) 280 x 337 x 595 mm (11 x 13.3 x 23.4 inch) Product Weight 13Kg (28.
Version 1.0 PartPro150 xP Operation Manual SUPPORTED FILE FORMAT The system accepts below file formats. The source files should be converted into .stl format in your CAD program. The source files should be sliced and converted into “.3wn” formats for production. For file conversion, please utilize the software “XYZprint AMUV”. File Format Description STL Format The file format is native to CAD software. It is widely used for 3D printing. Please always export your design files into .
Version 1.0 PartPro150 xP Operation Manual TOUCH SCREEN The printer screen shows the following menu when the system is ready. You can use the touch screen to print from the history, adjust the printer settings, and view the information on the material installed and resin temperature and system data.
Version 1.0 PartPro150 xP Operation Manual XYZPRINT AMUV “XYZprint AMUV” is the software for preparing the files for production. Be sure to install “XYZprint AMUV” before proceeding to production. To install “XYZprint AMUV”, download the software installer from: http://bit.
Version 1.0 PartPro150 xP Operation Manual OVERALL WORKFLOW The overall workflow for using PartPro150 xP is illustrated in the following chart. Refer to the explanation of each step in the relevant chapter. 3D design with CAD software and export the models into stl format Ready for Printing Prepare the production files with XYZprint AMUV › Manipulate the models – P.38 › Edit the supports for overhangs – P.40 › Export and slice the models – P.46 Start the production › with new models – P.
Version 1.0 PartPro150 xP Operation Manual 3. OPERATING THE PRINTER This chapter introduces all options on the printer screen. PRINT MENU To print a new file, the file should be transmitted from the software “XYZprint AMUV”. Refer to Chapter 5 for starting a new print. Using the touch screen on the printer, you can initial the production with the last 10 print jobs from the print history. Tap on [PRINT] in the top menu to launch the printing history.
Version 1.0 PartPro150 xP Operation Manual Start printing from the history 1. From the main menu, go to [PRINT], tap a history entry from the list view or thumbnail view. [List View] [Thumbnail View] Tap to enlarge the thumbview. Model_01 2. Review the printing settings. Tap [PRINT] to initial the production. [PRINT] button is disabled while the system is reading the slicing information from the history. Allow a few second before tapping the [PRINT] icon.
Version 1.0 PartPro150 xP Operation Manual RESIN MENU Resin menu provides detailed information on the resin cartridge, including the material type and resin model and the switch of auto-filling function. When the material level is running low, a warning sign will be shown on the RESIN icon. Tap on [RESIN] in the top menu to launch the information and settings related to the printing material.
Version 1.0 PartPro150 xP Operation Manual SETTINGS MENU The menu provides the control of platform movement, brightness and timeout of the screen, sound volume, display language, connectivity settings, and show the system information. Tap on [SETTINGS] in the top menu to go to system settings.
Version 1.0 PartPro150 xP Operation Manual Moving the platform The system controls the movement of the platform in normal operating. In the case that you will need to move the platform to the top or the bottom, follow the procedures below. 1. From the main menu, go to [SETTINGS] > [Platform]. 2. Select [Go Top] to move the platform to the top or select [Go Bottom] to move the plate to the bottom. 3. 4. Wait while the platform is moving. Press to exit the function.
Version 1.0 PartPro150 xP Operation Manual Adjusting the audio volume The embedded speaker alerts your operation on the screen and the status of production. You may adjust the audio volume or even mute the speaker. 1. From the main menu, go to [SETTINGS] > [General]. 2. Select [Sound]. 3. Tap the adjustment buttons on 2 sides or tap on the volume bar to adjust the audio volume. To mute the speaker, keep tapping until the speaker icon change to the mute sign or tap the speaker icon directly. 4.
Version 1.0 PartPro150 xP Operation Manual Structure of the Wireless icon A B Item Ethernet A Description Tap on this icon to switch on/off the Wireless connectivity. The icon displays in different color for showing current status. Switch of Wireless connectivity Wireless configuration enabled. Wireless configuration disabled. B When Wireless configuration is enabled with the icon shown in green, you can press this button to set up the Wireless connection.
Version 1.0 PartPro150 xP Operation Manual Connecting to a hidden Wi-Fi network 1. From the main menu, go to [SETTINGS] > [General]. 2. Tap the wireless connection icon to enable the function. Skip this step if the icon is shown in green. 3. Tap [Wireless] to enter the setting. 4. Swipe to the bottom of the list of available Wi-Fi connections, and tap [Add Network]. 5. Enter the exact name of the network in the [Network Name] field and tap to go back to the setting page. X| None 6.
Version 1.0 PartPro150 xP Operation Manual Structure of the Ethernet icon A Item B A Switch of Wireless connectivity Description Tap on this icon to switch on/off the Ethernet connectivity. The icon displays in different color for showing current status. Ethernet configuration enabled. Ethernet configuration disabled. B Ethernet Setup When Ethernet configuration is enabled with the icon shown in green, you can press this button to view the auto-assigned IP address or set up the Ethernet connection.
Version 1.0 PartPro150 xP Operation Manual Manually configuring Ethernet network The printer is set to obtain an IP address automatically by default. However, if you are using the printer on a network without DHCP, or want to prevent the printer's IP address from changing, you may specify IP address for the printer. Check the corresponding settings with your network administrator. Proceed to the following procedures after plugging the Ethernet cable to the Ethernet port at the back of the printer. 1.
Version 1.0 PartPro150 xP Operation Manual Viewing the IP address In the network configuration with several printers, you may identify the printer with its serial number and IP address. The printer is assigned an IP address when connected to the wireless and Ethernet network. When on the wireless network: 1. From the main menu, go to [SETTINGS] > [General] > [Wireless]. 2. Tap the connected network in the list of available network. 3. Find the IP address in the right section. XYZ-00001 192.168.2.
Version 1.0 PartPro150 xP Operation Manual PRINTING CONTROLS When the printing has begun, you can use the printer screen to check the printing progress and the information of the file in production, and control the printing. Tap << or >> to switch between different pages. Monitoring the progress Through the printer screen, you will find the information of printing progress, elapsed time, slicing settings and the estimated total print time. Tap << or >> to switch between different pages.
Version 1.0 PartPro150 xP Operation Manual Resuming the paused task Before resuming the paused task, make sure the resin bottle is installed correctly and the front and the side covers are closed securely. Tap the [RESUME] button and wait while the system resuming the printing. Canceling the printing You can cancel the printing anytime if necessary. To cancel the printing: 1. Tap [CANCEL]. 2. Tap [CONFIRM] on the next page. 3.
Version 1.0 PartPro150 xP Operation Manual Display language The following languages are available on the software interface: German, English, Spanish, French, Italian, Korean, Japanese, Simplified Chinese, and Traditional Chinese. To change the display language, select the preferred language from the drop-down list in the [General] tab. Display unit The software can display the models in millimeters or inch.
Version 1.0 PartPro150 xP Operation Manual 4. OPERATING XYZprint AMUV Launch XYZprint AMUV by double-clicking on the desktop icon AMUV from the list of program on your computer. on the Windows desktop or select XYZprint SOFTWARE INTERFACE The software illustrates the printing environment on the printer. An empty workspace is presented with grids for showing the display unit in centimeter or inch. All models loaded to the software will be placed on the workspace.
Version 1.0 PartPro150 xP Operation Manual Function 2 Import Import models in .stl/.3ws/.3wn format to the workspace. A Export Slice the models on the workspace and export to .3wn format. B Save Save the models on the workspace as .stl or .3ws file. B Print Setup printing preference and send the objects for printing B About 4 When Enabled Top Bar Setting 3 Description Set up interface language, display unit, printer model, finetuning printout dimensions, and enable/disable autoposition.
Version 1.0 PartPro150 xP Operation Manual KEYBOARD SHORTCUTS AND MOUSE CONTROLS To work more efficiently in the software, you can use the following keyboard shortcuts and mouse controls: Ctrl + A: Select all objects on the workspace Alt + drag the right or left button: Move the object on X/Y axis Delete: Delete the selected objects from the platform.
Version 1.0 PartPro150 xP Operation Manual COLOR DISPLAY OF OBJECTS The color of the printed parts is depending on the material installed, and is not related to the display color in the software. The color displayed in the software allows for easy distinguish of the status of objects on the workspace. The indication of different colors is explained as following: Color White Shaded pink Red Description The models within the printing area. Overhang area on the models.
Version 1.0 PartPro150 xP Operation Manual Display language The following languages are available on the software interface: German, English, Spanish, French, Italian, Korean, Japanese, Simplified Chinese, and Traditional Chinese. To change the display language, select the preferred language from the drop-down list in the [General] tab. Display unit The software can display the models in millimeters or inch.
Version 1.0 PartPro150 xP Operation Manual PREPARING THE FILES Importing Models to the Workspace Models to be printed should be loaded on the workspace for preparation. To load .stl, .3ws, or .3wn file to the workspace for printing: 1. Click [Import] icon. 2. Browse to the target folder, select the file type to be imported from the file-format drop-down list in the [Import File] window. Navigate to your file and click [Open]. You can import only one file at a time.
Version 1.0 PartPro150 xP Operation Manual Rotating the models The orientation of models may impact the printing quality, successful rate and printing time. To ensure a successful print, you may need to rotate the models and add supports to overhangs based on the features of each model. Key consideration for orientation: Top-heavy structure may fall off the platform, and may require more supports to hold it on the platform.
Version 1.0 PartPro150 xP Operation Manual Adding supports automatically Support structure is required under overhangs. It prevents the falling for gravity and the deforming due to the peeling force during printing, and increases adhesion of the model to the platform. The software is able to analyze the features of the model and add support structure to where necessary. You may add or delete support structure based on the features of the print manually.
Version 1.0 PartPro150 xP Operation Manual Editing supports manually You can build the supports from scratch with the manual mode, or use it to adjust the supports generated in the Auto mode. In Auto Mode, all supports are in the same size at the contact points. However, the size of the contact can be set to different based on the features of the object. Larger contact may be required for heavy part. Smaller contact is good enough for holding lighter structure. Also it is easier for post-processing.
Version 1.0 PartPro150 xP Operation Manual Cone support also provides better adhesion to the platform, making it helpful for holding the base of heavy objects on the platform. When the cone support is added to the object, it’s recommended to sand it away for better surface finish. Structure of Cone Supports Item Description A Contact Area A larger contact area may be required for heavy objects. B Top Diameter Minimum diameter: 2mm. C Base Diameter Minimum diameter: 3mm.
Version 1.0 PartPro150 xP Operation Manual 4. Adjust the contact area of the cone support if necessary. To adjust the contact area of the cone support, go back to the function menu “Support” > “Cone”, and select the button “Contact Area”. Click on the targeted cone (selected cone will change to blue) and drag the slider to adjust the contact area. Click “Done” once you have adjusted the contact area of all cones. Cone support is only available when the overhang is at least 6mm above the platform.
Version 1.0 PartPro150 xP Operation Manual Tree Supports Tree supports connect to your 3D objects with very small contact. It is suitable for holding the details on jewelry designs. Structure of Tree Supports Item Description A Contact Area The area where the tree support connect to the objects. A larger contact area may be required for heavy objects. B Branch The thin support which contacts the objects directly. C Trunk The base of the tree support. To add tree supports 1.
Version 1.0 PartPro150 xP Operation Manual 4. Set up the branches. Switch to “Branch” setup. Click on the targeted trunk with a click on it. Click on the overhangs on the model to add branches to the selected trunk. To delete a branch, click on the thin stick to delete it. 5. Click “Generate” after setting up all marks 6. Adjust the contact area of the branches if necessary. To adjust the contact area of the branches, go back to the function menu “Support” > “Tree”, and select the button “Contact Area”.
Version 1.0 PartPro150 xP Operation Manual CONVERTING TO THE PRODUCTION FILES Exporting the files When finishing editing the files and the supports, click on [Export] to save the model to a sliced .3wn file. Once the file is sliced, you may skip repeating settings in the future. To export the file: 1. Click [Export] icon. Material: Printing setup varies based on the color and material of the resin. Please set the option based on the resin bottle to be used.
Version 1.0 PartPro150 xP Operation Manual Starting a printing task New files can be sent to the printer via USB connection, wireless connection or Ethernet connection. To start a new printing task: 1. Initial the connection through [Printer Monitor]. Refer to P.35. 3. Printout setting window (options are the same as the [Export] function) will pop up. Set your printing preference based on the features of the objects and hit [Print] to proceed. 2. Press [Print] icon on the top bar.
Version 1.0 PartPro150 xP Operation Manual SWITCHING THE VIEW OF THE WORKSPACE The view angel of the workspace can be changed anytime by dragging the right or left button on the mouse. Or to view the workspace from the standard views, you can use the [View] tool. To switch between standard view angles: 1. Click [View] icon. 2. 48 Select one of the icons and the software will turn the specified side of the workspace to your front view.
Version 1.0 PartPro150 xP Operation Manual VIEWING THE INFORMATION OF THE MODELS You may want to check the information of the models imported to the workspace. The software provides the information on file name, file format and the position and dimensions of each selected model. To view the information on the models: 1. Select an object on the workspace and click [Info] icon. 2. Read the information of the selected object. To close the information window, hit [Close] button.
Version 1.0 PartPro150 xP Operation Manual 5. POST-PROCESSING CLEANING UP THE MODELS FROM THE PLATFORM Wear protective gloves while cleaning up the platform and the printed models. 1. The printer screen displays below message when the printing is completed. Tap [CONFIRM]. 2. Release the bolt handle over the platform and pull out the platform. Recess resin may drip from the platform. It is advised to hold a tray or absorbent cloth under the platform while removing it. 3.
Version 1.0 PartPro150 xP Operation Manual POST-PROCESSING Resin printed models should go through the following post-processing steps to ensure it is ready for final application: Alcohol bath Support removal Sanding Post-curing Protective gloves should be worn before handling printed models. Alcohol bath Support removal Rinse part in Alcohol (≧95% Alcohol). Pour alcohol into the rinse bucket, shake the print for a few minutes, and then rub it with your fingers thoroughly.
Version 1.0 PartPro150 xP Operation Manual MAINTENANCE Filtering resin in the tank Uncured resin in the tank can be left for the next print if you are not change to other material. However, cured debris may be left in the resin. To ensure the printing quality, be sure to filter the resin and pour it back to the tank before the next print. Preservation of the Uncured Resin Avoid exposing uncured resin to the air for long periods of time.
Version 1.0 PartPro150 xP Operation Manual APPENDIX APPENDIX 1 TROUBLE SHOOTING The printer and the software alert any abnormal status with an error code and relevant error message. Check the following charts for the standard procedures for troubleshooting. If any issue persists, please contact your service representative.
Version 1.0 PartPro150 xP Operation Manual of the cartridge. If the ID tag is missing, please contact the service center for help. 2002 Laser module not calibrated Contact the service center for help. 2003 Resin bottle ID tag voided The ID tag is void when the resin bottle is empty. Please replace the resin cartridge. 2004 Covers opened Close the covers securely. 2005 Invalid resin tag detected Install XYZprinting resin bottle and try again.
Version 1.0 PartPro150 xP Operation Manual This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
