User Manual

ManualsBrandsYaesu Musen ManualsAudio EquipmentBluetooth Headset

Controls & Connections

Microphone

POWER switch

VOLUME

(

–

)

switch

Pressing this switch decrease the receiver volume level.

Press this switch while pressing and holding the PTT

switch, to decreases the microphone gain.

VOLUME

(

)

switch

Pressing this switch increase the receiver volume level.

Press this switch while pressing and holding the PTT

switch, to increases the microphone gain.

LED Indicator

Blinking Blue: When the BH-2 Bluetooth

Headset is

correctly recognized by the transceiver.

Blinking Red: When the BH-2 Bluetooth

Headset is

not correctly recognized by the trans-

ceiver.

Blinking Red/Blue: Battery Voltage is Low.

PTT switch

Press this key to transmit. Release this key to return to

receive (Depends on transceiver settings).

SPEAKER

Earhook

You can wear the BH-2 on your left or right ear.

“BH-2” Bluetooth

Head Set

When the optional BU-1 Bluetooth

Adapter Unit is installed in the Transceiver*, you may use the BH-2 Bluetooth

Headset as a wireless link to send and receive audio to the Transceiver*.

* Check with your Vertex Standard Dealer or Catalog for applicable models.

Wearing the BH-2

1. Open the earhook.

2. Loop the earhook over your ear.

3. Press the BH-2 to your ear.

4. Adjust the flexible boom microphone

by bending the boom towards your

mouth.

The BH-2 comes ready to fit the left ear. You may change

the BH-2 to fit the right ear in the following procedure.

1. Remove the Earhook by pushing it out with a pointed

object.

2. Insert the Earhook from the other side.

Pairing

Before you can use your BH-2 for the first time, the BH-2

and the transceiver must be paired.

Refer to the Transceiver’s Operating Manual for Pairing in-

structions.

P Please bring the BH-2 and the Transceiver close together

when doing Pairing.

1. Make sure that the BH-2 is off.

2. Press and hold the POWER switch for five seconds, until

the LED indicator blinks red/blue alternately.

When the BH-2 is correctly recognized (Requires a 20 to 30

seconds) by the transceiver, the LED indicator will blink

blue.

Effective Communications Range

The communications range between the BH-2 and the

Transceiver is around 10m (33 ft).

Obstacles between the BH-2 and the Transceiver may

decreas the communications distance.

When you move out of range, the beeper sounds a low

pitch tone. When you move back into range, the beeper

sounds a high pitch tone.

Turning ON and OFF

o turn the o turn the

o turn the BH-2

ON ON

Press and hold the POWER switch for three seconds, un-

til the BH-2’s LED indicator glows red, and the beeper

sounds a high pitch tone.

When the BH-2 is correctly recognized by the transceiver,

the LED indicator will blink blue.

PWhen the BH-2 is not correctly recognized by the trans-

ceiver, the LED indicator will blink red.

o turn the o turn the

o turn the BH-2

OFF OFF

OFF

Press and hold the POWER switch for five seconds, until

the BH-2’s red LED indicator blinks rapidly, the beeper

sounds two brief tones, and the BH-2 turns off.

LED indicator

POWER Switch

For more comfort when wearing the BH-2, affix the sup-

plied sponge on the speaker and press the supplied sponge

ball onto the earhook, and adjust as necessary.

Operation

ransmissionransmission

ransmission

Press the PTT switch to transmit, and release the switch

to return to receive (Depends on transceiver settings).

Adjusting the VAdjusting the V

Adjusting the V

olume levelolume level

olume level

Adjust the receiver audio level, using the VOLUME (

–

) or

(+) switch.When the audio level reaches the maximum

or minimun, the beeper sounds two brief tones.

VOLUME (

): Adjusts the receiver audio level upward.

VOLUME (

–

): Adjusts the receiver audio level downward.

Microphone Gain SettingMicrophone Gain Setting

Microphone Gain Setting

Press and hold the PTT switch, while using the VOLUME

(+) or (

–

) switch to select a comfortable Microphone gain

level (Five steps). When the microphone gain reaches the

maximum or minimun, the beeper sounds a high pitch tone.

VOLUME (

): Sets the MIC gain upward.

VOLUME (

–

): Sets the MIC gain downward.

Battery

When the battery voltage becomes low, the BH-2’s LED indi-

cator will blink red/blue alternately, and the beeper sounds

a low pitch tone.

If the battery has never been used, or its charge is depleted,

it may be charged by connecting to the Charger Sleeve* or

Charger Cradle*, as shown in the illustration.

Please refer to the transceiver’s manual for installation of

the Charger Sleeve.

* Check with your Vertex Standard Dealer or Catalog for appli-

cable models.

1. Insert the BH-2 into the Charger Sleeve or Charger Cradle.

NoteNote

Note

: If the BH-2 is inserted into the Charger Sleeve or

Charger Cradle while the BH-2 power supply is

“ON”, it is automatically set to “sleep” mode.

When it is disconnected from the Charger Sleeve

or Charger Cradle, the BH-2 will be active again.

2. If the BH-2 is inserted correctly, the LED indicator will

glow Red. A fully discharged battery will be charged com-

pletely in 3 hours. When charging is finished, the LED

indicator will glow blue.

BH-2 is not designed to attach to a motorcycle helmet.

Specifications are subject to change without notice.

VOLUME (+) Switch

VOLUME (–) Switch

PTT Switch

Battery saverBattery saver

Battery saver

If there has been no signal or key button activity for 20 sec-

onds, the Battery Save automatically puts the BH-2 in “sleep”

mode, to conserve battery life.

When a signal is received or the PTT key is pressed the

BH-2 will be active again.

Refer to the Transceiver’s Manual for Battery saver instructions.

Specifications

Bluetooth specification Ver1.2

Bluetooth profiles HSP

Radio Frequency 2402 MHz - 2480 MHz

Modulation method GFSK

Transmitter output power 0 dBm Class 2

Receiver sensitivity <-80 dBm

Distance (open area) 32 ft (10 meters)

Audio format SBC

Audio frequency range 100 Hz - 20 kHz

Power supply Rechargeable Lithium-Polymer

Battery life 6 hours

Button/Switch Power On/Off, Volume Up/Down, PTT

LED indicators Power on: Flash blue twice

Unlink: Flash red

Link: Flash blue

Pairing: Red and Blue blinking

Battery low: Flash red and blue

Power off: Flash red 3 times

Operating temperature 32 °F to 104 °F (0 °C to 40 °C)

Operating humidity 5 - 90 %

Certification FCC, CE, BQB

Replacement Parts

Example:Use the “CAB-1” Example:Use the “CD-40”

Ear hook ................. S8002323

Ear hook sponge ..... S8002325

Speaker sponge ....... S8002324

Wind Screen ........... S8002322

EAF44U760

Summary of content (3 pages)

PAGE 1
“BH-2” Bluetooth® Head Set When the optional BU-1 Bluetooth® Adapter Unit is installed in the Transceiver*, you may use the BH-2 Bluetooth® Headset as a wireless link to send and receive audio to the Transceiver*. * Check with your Vertex Standard Dealer or Catalog for applicable models. Controls & Connections Microphone POWER switch VOLUME (–) switch Wearing the BH-2 Battery 1. 2. 3. 4.
PAGE 2
“BH-2” Bluetooth® Head Set The “BH-2” is a Bluetooth® Head Set for Vertex Standard Transceivers*. When the Bluetooth® Head Set “BH-2” is used with the “BU-1” Adapter, you can enjoy comfortable hands free operation. Declaration of Conformity *: Please refer to the Vertex Standard catalog for the correct “BH-2” Head Set for the radio you are using. This device complies with Part 15 of the FCC Rules.
PAGE 3
ýesky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zaĜízení] je ve shodČ se základními požadavky a dalšími pĜíslušnými ustanoveními smČrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.