FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Accessories & Options Supplied Accessories Mobile Mounting Bracket DC Power Cord W/Fuse Spare Fuse 15 A Angle Sub Panel Hex Wrench Operating Manual Warranty Card Optional Accessories DTMF Microphone MH-68A6J Normal Microphone MH-68B6J Panel Separation Kit YSK-M10 Bluetooth Head Set BH-1 Bluetooth Adapter Unit BU-1 Head Set Charger Sleeve CAB-1 Microphone Jack MEK-M10 Ear Phone for BH-1 FEP-4 High-Power External Speaker MLS-2
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Installation This chapter describes the installation procedure for integrating the FTM-10R into a typical amateur radio station. It is presumed that you possess technical knowledge and conceptual understanding consistent with your status as a licensed radio amateur. Please take some extra time to make certain that the important safety and technical requirements detailed in this chapter are followed closely.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual antenna installation. (!) Be certain to wrap any wire or cable splices thoroughly with insulating electrical tape, to prevent short circuits. (!) Do not route cables or wires through door jambs or other locations where, through wear and tear, they may become frayed and shorted to ground or to each other. (!) Do not stand in front of a directional antenna while you are transmitting into that antenna.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual the vertical sides of the driven element (or at a side corner, in the case of a diamond-shaped Cubical Quad). Note that this transceiver is designed with wide frequency coverage in the VHF/UHF spectrum. For general listening, you may wish to have a broadband antenna such as a discone available, as a directional antenna such as a Yagi will have degraded performance outside the Amateur band for which it is designed.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual How to use the supplied Angle Sub Panel FTM-10R can tilt the front panel by using supplied Angle Sub Panel. Remove the four screws affixing the Front Panel, then remove the Front Panel from the transceiver’s body. Disconnect the 8-pin modular plug from the transceiver’s body. Remove a screw affixing the Straight Sub Panel, then remove the Straight Sub Panel from the Front Panel.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual The optional MLS-200-M10 High-Power External Speaker includes its own swivel-type mounting bracket, and is available from your Yaesu dealer. Other external speakers may be used with the FTM-10R, if they present the specified 8-Ohm impedance and are capable of handling the 8 Watts of audio output supplied by the FTM-10R. Base Station Installation The FTM-10R is ideal for base station use as well as in mobile installations.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 3. LCD Display The main digits on the display may show the operating frequency, memory name, or any of many parameters during Menu setup. 4. [BANDS] Key Press this key to switch the operating band as follows: 2 m Amateur Band 430 MHz Amateur Band Band Home Channel Audio Line FM BC Band AM BC Band WX 2 m Amateur Band … 5. [X] Key This key function is different by setting of [SELECT] key.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Clock Stop Watch Timer (Sum) Current transceiver’s body Stop Watch Timer temperature inside the Clock … *: The Clock/Timer mode is disabled at the factory default. To enable this mode, see page ??. Top Panel Controls & Switches 1. PTT Key Press this key activate the internal microphone. 2. [TOPT] Key Press this key momentarily to select the functions of the top panel’s [F].
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Rear Panel Connectors 1. ANT Jack Connect your antenna hear, using a type-M (PL-259) plug and coaxial cable. 2. DC 13.8 V Cable Pigtail w/Fuse This is the power supply connection for the transceiver. Use the supplied DC cable to connect this pigtail to the car battery or other DC power supply capable of at least 10 Amperes (continuous duty). Make certain that the red lead connects to the positive side of the supply. The fuse is 15-A. 3.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 4. Keypad These 16 keys generate DTMF tones during transmission. In the receive mode, these 16 keys can be used for direct frequency entry. The [A], [B], [C], and [D] keys replicate the functions of the front panel keys ([BANDS], [X], [BANDT], and [SELECT]), and also the [*] and [#] keys replicate the functions of the top panel keys ([TOPT] and [F]). Basic Operation Turning the Transceiver On and Off 1.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual squelch threshold level is appeared on the LCD. 4. Rotate the DIAL knob just to the point where the noise is silenced and the front panel’s green “BUSY” indicator turns off. If the SQL control is set further clockwise, sensitivity to weak signals is reduced. 5. Press the [SELECT] key momentarily to save your new setting and resume normal operation.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual turned off. Now, the DIAL knob becomes dial knob. 2. Rotating the DIAL knob allows tuning in the pre-programmed steps. Clockwise rotation of the DIAL knob causes the transceiver to be tuned toward a higher frequency, while counter-clockwise rotation will lower the operating frequency. 3.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Transmission To transmit, simply close the PTT (Push To Talk) key on the microphone when the frequency is clear. Hold the microphone approximately 1” (25 mm) from your mouth, and speak into the microphone in a normal voice level. When your transmission is complete, release the PTT switch; the transceiver will revert to the receive mode. During transmission, the red “TX” indicator at front panel will appear.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Advanced Feature: You may also lock out the PTT key when the LOCK mode is activated via the Menu Item “F24 PTT LOCK.” See page ??. Advanced Operation Display Brightness The FTM-10R display illumination has been specially engineered to provide high visibility with minimal disruption of your “night vision” while you are driving. The brightness of the display is manually adjustable, using the following procedure: 1.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 2. Rotate the DIAL knob to select Menu Item “F39 STEP.” 3. Press the [X] key to enable selection of this Menu Item. 4. Rotate the DIAL knob to select desired step size (5.00/6.25/8.33/10.00/12.50/15.00/20.00/25.00/50.00/100.00/200.00 kHz or AUTO). 5. Press the [SELECT] key momentarily to save the new setting and exit to normal operation. Note: 1) AM BC band only choose 9 kHz and 10 kHz.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual press the PTT key to sound the voice/sound from the external speaker. 4. On the PA mode, when speak into the microphone while pressing the PTT key, outputs your amplified voice from the external speaker. 5. Rotate the DIAL knob control the AF output level. Note: You may exclude the five functions which is listed above from a list which is by a Menu Item “F17 FNC KEY” individually.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 7. Repeat above step regarding the “DAY,” “DAY OF WEEK,” “CLOCK,” “MINUTE,” and “SECOND.” 8. When adjust of “SECOND” is finish, press the [BANDS] key. If you want to alarm which sound every “00” minute, rotate the DIAL knob to change “OF” into “ON.” 9. Now, press the [BANDS] key to save the new setting and exit to Clock/Timer mode. Note: 1) You may adjust the “CLOCK” and “MINUTE” via Menu Item “T2 TIME ADJ” as well.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual programmed by the beep sound and (white) flushing the LED. 1. Press the [SELECT] key repeatedly to recall the Clock/Timer mode. 2. Press and hold the [SELECT] key for one second to activate the Clock/Timer Customization mode. 3. Rotate the DIAL knob to select Menu Item “T6 UP TIMER.” 4. Press the [X] key momentarily to enable selection of this Menu Item. 5. Rotate the DIAL knob to select desired interval. 6.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual will shut down the radio automatically. Repeater Operation The FTM-10R includes a host of convenience features which makes operation on amateur repeaters both efficient and enjoyable.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Automatic Repeater Shift The ARS (Automatic Repeater Shift) feature in this transceiver allows easy and convenient repeater operation by automatically activating the repeater shift function whenever you tune to a standard repeater subband. The ARS function is preset at the factory to conform to the standards for the country to which it is exported. The ARS function is enabled at the factory. To disable it: 1.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual receives a call from another radio sending out a matching CTCSS tone. This can help keep your radio quiet until a specific call is received, which may be helpful while operating in congested areas.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 3. Press the [X] key to enable selection of this Menu Item. 4. Rotate the DIAL knob so that “DCS” appears on the display; this means that the DCS Encoder/Decoder is active, which mutes your FTM-10R’s receiver until it receives a call from another radio sending out a matching DCS tone. 5.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Tone Pair. 5. Rotate the DIAL knob to set the CTCSS Tone number which corresponds to the first tone of the Receiving CTCSS Tone Pair. 6. Press the [BANDS] key, then rotate the DIAL knob to set the CTCSS Tone number which corresponds to the second tone of the Receiving CTCSS Tone Pair. 7. Repeat step 6 for setting the Transmitting CTCSS Tone Pair. 8.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual operation. When you are called by a station whose transceiver is sending a CTCSS tone, DCS code, or CTCSS code pair which matches that set into your Decoder, the Bell will ring in accordance with this programming. Split Tone Operation The FTM-10R can be operated in a “Split Tone” configuration, to enable operation on repeaters using a mix of both CTCSS and DCS control via the Menu (Set) mode. 1.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual momentarily, to store the displayed data into the memory channel slot. The “MIN” notation will disappear (since you are still operating in the VFO mode). 4. To store other frequencies, repeat steps 1 through 3, remembering to set the repeater shift, CTCSS/DCS tone, and TX power level, as appropriate. Note: The above procedure will be used for virtually all memory storage circumstances.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Group Memory In the FTM-10R, the memory channel data is assigned to the Memory Group automatically. The GRP bank can be recalled by pressing the front panel’s [BANDT]/[BANDS] key. You may observe the Memory Group between the Audio Line and 2 m Amateur Band. You may assign/delete the memory channel to/from the Memory Group. 1. Recall the memory channel on which you wish to assign to or delete from the Memory Group. 2.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 3. Rotate the DIAL knob to select Menu Item “M3 MEM SORT.” 4. Press the [X] key momentarily, to appear the confirmation message (“SORT ?”) on the LCD. 5. Press and hold the [X] key to appear the message (“SORTING”) on the LCD, then the FTM-10R is reset automatically and sorting is complete.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual See page ?? for details. Squelch Level The FTM-10R enables to set the squelch threshold level every memory channel individually. 1. Recall the memory channel on which you wish to set the squelch threshold level. 2. Press and hold the [X] key to enter the Memory Channel Customization mode. 3. Rotate the DIAL knob to select Menu Item “M7 SQL.LEVEL.” 4.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 4. Rotate the DIAL knob to select Menu Item “M11 TX FREQ.” 5. Press the [X] key momentarily, then rotate the DIAL knob to select “S-DUPLEX”). You may notice a “RPTR –” and “RPTR +” indication on the display while you rotate the DIAL knob still more, these are Standard Repeater Shift operation which was discussed on page ??. 6. Press the [SELECT] momentarily to save the new setting and return to the memory recall mode.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual The FTM-10R allows you to scan the VFO frequency and memory channel. It will halt on signals encountered, so you can talk to the station(s) on that frequency, if you like. Scanning operation is basically the same in above both modes. Before you begin, take a moment to select the way in which you would like the scanner to resume scanning after it halts on a signal.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual previous section. 6. To cancel scanning, press the [F] key momentarily again. Note: 1) In the factory default, the scanner initiates upward scanning. You may change the scan start direction to downward scanning by Menu Item “F31 SCN.UP/DN.” 2) In the factory default, the FTM-10R considers the 144 MHz Amateur Band and 430 MHz Amateur Band to be an independent band while the scanner is activated.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 1. Set the FTM-10R to the Memory Recall mode by pressing the [X] key, if necessary, “M” notation appears on the right side of the display. 2. Rotate the DIAL knob to select the Memory Channel to be skipped during scanning. 3. Press and hold the [X] key to enter the Memory Channel Customization mode. 4. Rotate the DIAL knob to select Menu Item “M6 SKIPONLY.” 5.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 5. Press the [SELECT] key momentarily to save the new setting and exit to normal operation. 6. Now, initiate the scanner (press the [TOPT]/[TOPS] key repetitively, until the “SCAN” notation appears on the display, then press the [F] key). Only 7. To cannel the Preferential Memory Scanning, select “ALL MEM” in step 4 above.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual the message slot, (2) store the same member list into the member box, and (3) store the desired coordination frequency into the CLUB channel. Preparations Programming a Message (requires all members set the same message into the same message slot with the same order.) The FTM-10R has 20 message slots, including 11 factory-programmed messages for convenient recall, as shown below.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 6. Rotate the DIAL knob to select the first character of the personal ID you wish to store, then press the [BANDS] key momentarily to save the first character of the personal ID and move on to the next place. 7. Repeat previous step to complete the personal ID. If you a mistake, press the [BANDT] key to move back to the incorrect character, then re-enter the correct character. 8.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Before sending a message, you must change the setting of top panel’s keys ([TOPT], [TOPS], and [F] keys) to enable the selection of the transmit message. 1. Press and hold the [SELECT] key for one second to activate the Menu (SET) mode. 2. Rotate the DIAL knob to select Menu Item “F42 TOP KEY.” 3. Press the [X] key to enable selection of this Menu Item. 4.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 4. Rotate the DIAL knob to until “CODE” appears on the display; this activates the WIRESTM with the SRG mode. The “%” icon will appear on the display. 5.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 7. Press the [BANDS] key momentarily to accept the first digit and move to the second digit of the DTMF string. 8. Repeat the previous steps until you have completed the access code (“#(F)1101D”). 9. If you make a mistake, press the [BANDT] key to back-digit the cursor, then re-enter the correct number. 10. Press and hold the [X] key for one second to save the new setting. 11.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual are stored into a special Smart Search memory band, consisting of 31 memories (15 above the current frequency, 15 below the current frequency, plus the current frequency itself). All channels where activity is present will be loaded into the Smart Search memories; whether or not all 31 memories are filled, the search will stop after one sweep in each direction. Storing Smart Search Memories 1.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Whenever you push the PTT switch, or every 25 seconds after ARTS is activated, your radio will transmit a signal which includes a (subaudible) DCS signal for about 1 second. If the other radio is in range, the beeper will sound (if enabled) and the display will show “IN.RNG” as opposed to the out of range display “OUT.RNG” in which ARTS operation begins.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Manual DTMF Tone Generation You can generate DTMF tones during transmission manually. Press and hold the [X] key while transmitting, if necessary. The “DT CODE” indication will appear in the display for a moment (thus enabling the Manual DTMF Tone Generation). Note: The “DT MEM” indication is DTMF Autodialer mode, described later. While transmitting, press the desired numbers on the keypad. When you have sent all digits, release the PTT key.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual will appear in the display for a moment (thus enabling the DTMF Autodialer). While the DTMF Autodialer is activated, the “TELEPHONE” icon will appear on the LCD. Note: The “DT CODE” indication is Manual DTMF Tone Generation mode, described previously. In the Autodialer mode, which you just engaged, first press the PTT key, then press the microphone’s numeric key ([1] through [9]) corresponding to the DTMF memory string you wish to send.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual ARTS: Engages the ARTS™ operation. TAG: Switches the display between indication of the frequency and the channel’s Alpha/Numeric label while receiving on the memory channel. 5. MHz: Allows to 1-MHz tuning step while receiving on the VFO mode. SCAN: Engages the Scan operation CLUB: Recall the CLUB channel. WX: Switches operation to the Weather channels bank.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual operation. Volume Setting Alert feature The FTM-10R provide the Volume Setting Alert feature which is . 1. Press and hold the [SELECT] key for one second to activate the Menu (SET) mode. 2. Rotate the DIAL knob to select Menu Item “F46 VOL.PRESET.” 3. Press the [X] key to enable selection of this Menu item. 4. Rotate the DIAL knob to select the desired effect level. ON-SET: Activates the Volume Setting Alert feature.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual SF5 RESET: Clears all memories and other settings to factory defaults. SF6 RBT PAIR: Set up the Bluetooth device which is connected to the transceiver. This is not reset operation. SF7 FBT PAIR: Set up the Bluetooth device which is connected to the front panel of the transceiver. This is not reset operation. 4.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Function: Select the Tone Pitch control for the received audio. Available Values: BASS-3/BASS-2/BASS-1/NORMAL/TREBLE-1/TREBLE-2 Default: NORMAL Set Mode Item [F3 ARS] Function: Enables/Disables the Automatic Repeater Shift function. Available Values: ON/OFF Default: ON Set Mode Item [F4 BAND] Function: Enables/Disable the band expansion.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Function: Enables/Disables the Bluetooth function (requires the optional BU-1 Bluetooth Unit). Available Values: OFF/ON VOX.OF/ON VOX.HI/ON VOX LO Default: OFF OFF: Disable the Bluetooth function. ON VOX.OF: Activate Bluetooth function without the VOX feature. ON VOX.HI: Activate Bluetooth function with the VOX feature (VOX gain: High). ON VOX.LO: Activate Bluetooth function with the VOX feature (VOX gain: Low).
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Set Mode Item [F13 DC VOLT] Function: Indicates the DC Supply Voltage. Set Mode Item [F14 DIMMER] Function: Setting of the display’s illumination level. Available Values: MIN/LOW/NOR/HIGH/MAX Default: MAX Set Mode Item [F15 DTMF] Function: Programming of the DTMF Autodialer. See page ?? for details. Set Mode Item [F16 DUAL MIX] Function: Select the Priority Channel Scanning (Dual Watch) Resume mode.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Set Mode Item [F20 MEMBER] Function: Programming a Member List for the Message feature. See page ?? for details. Set Mode Item [F21 MESSAGE] Function: Programming a Message for the Message feature. See page ?? for details.. Set Mode Item [F22 PAGER] Function: Enables/Disables the Enhanced CTCSS Paging & Code Squelch function and setting the Receiving/Transmitting Pager Code for the Enhanced CTCSS Paging & Code Squelch function.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual HOLD: The scanner will stop when a signal is received, and will not restart. TIME 3S/5S/10S: The scanner will hold for selected resume time, then resume whether or not the other station is still transmitting. Set Mode Item [F27 RPT MOD] Function: Sets the Repeater Shift Direction. Available Values: RPTR OFF/RPTR -/RPTR + Default: Depends on the transceiver version, as well as the setting of Set Mode Item [F3 ARS].
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Set Mode Item [F31 SCN.UP/DN] Function: Select the scan start direction which initiates the scanner using scan command by pressing the [F] key. Available Values: UP START/DWN.START Default: UP START Set Mode Item [F32 SHIFT] Function: Sets the magnitude of the repeater Shift. Available Values: 0.00 - 99.95 MHz (50 kHz increments) Default: Depends on the operating band and transceiver version.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Function: Setting of the DCS code. Available Values: 104 standard DCS codes Default: DCS(023) Set Mode Item [F37 SQL.EXPND] Function: Enables/Disables split CTCSS/DCS coding. Available OFF/ON Default: OFF When this Set Mode Item is set to “ON,” you will see the following additional parameters after the “DCS” parameter while configuring Set Mode Item [F37 SQL TYPE]. DCS ENC: DCS Encode only.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Default: MONO Set Mode Item [F41 SUB BAND] Function: Enables/Disable the Sub Band operation. Available Values: OFF/AM MIX/AM MUTE/FM MIX/FM MUTE/LIN MIX/LINE MUTE Default: OFF OFF: Disable the Sub Band operation. AM MIX: You may receive the amateur band frequency while listen the AM Broadcast band.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Default: FNC Set Mode Item [F43 TOT] Function: Setting of the TOT time Available Values: 1MIN - 30MIN or OFF Default: 6MIN (minutes) The time-out timer shuts off the transmitter after continuous transmission of the programmed time. Set Mode Item [F44 TX POWER] Function: Selects the transmit power output level. Available Values: LOW/MID/HIGH Default: HIGH Set Mode Item [F45 VFO-VOL] Function: Enables/Disables the .
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual F-HAND: Enable the VOX operation for the optional MH-68A6J which is connected to the front panel’s MIC Jack. FRONT: Enable the VOX operation for the front panel microphone. Set Mode Item [F49 VOX SENS] Function: Sets the VOX sensitivity. Available Values: MIN/1/2/3/4/5/6/7/8/MAX Default: 5 Set Mode Item [F50 WIRES] Function: Enable/Disable the Internet Connection feature.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual Channel Steps: 5, 6.25, 8.33, (9), 10, 12.5, 15, 20, 25, 50, 100, 200 kHz (9): AM Only Frequency Stability: ±5 ppm (–10 °C to +60 °C) Repeater Shift: ±600 kHz (144 MHz) ±1.6 / 5.0 / 7.6 MHz (MHz) Emission Type: F1, F2, F3 Antenna Impedance: 50 Ω Supply Voltage: Nominal: 13.8 V DC, Negative Ground Operating: 11.7 ~ 15.8 V, Negative Ground Current Consumption: 0.5 A (Receive) 8.3 A / 6 A / 2A (TX, 144 MHz 50W / 20 W / 5 W) 8.
FCC ID: K6620275X40 IC ID: 511B-20275X40 FTM-10R Operating Manual 0.25 µV for 12 dB SINAD (150-174 MHz, FM) 1 µV TYP for 12 dB SINAD (174-222 MHz, WFM) 0.8 µV TYP for 10 dB SN (300-336 MHz, AM) 0.25 µV TYP for 12 dB SINAD (336-420 MHz, FM) 0.2 µV for 12 dB SINAD (420-470 MHz, FM) 5 µV TYP for 12 dB SINAD (470-540 MHz, WFM) 5 µV TYP for 12 dB SINAD (540-800 MHz, WFM) 0.4 µV TYP for 12 dB SINAD (800-899.99 MHz, FM) 0.8 µV TYP for 12 dB SINAD (900 - 999.
