FCC ID: K6630173X3D/IC ID: 511B-30173X3D QUEST-X GX1500S 25 Watt VHF/FM ITU Class D DSC Marine Transceiver Owner's Manual Oversized alphanumeric LCD, knobs and keys Direct keypad entry of a channel using the keypad Removable ClearVoice speaker microphone with 16/9 key and channel selection Display shows channel names, and repeats GPS information8 Capable of connecting a optional enhanced RAM+ second station remote microphone or VH-310 Handset DSC distress call automatically broadcasts lat/long
FCC ID: K6630173X3D/IC ID: 511B-30173X3D TABLE OF CONTENTS 1 2 3 4 5 6 7 GENERAL INFORMATION ..................................................................................................... 4 PACKING LIST ....................................................................................................................... 4 OPTIONS ................................................................................................................................ 4 SAFETY / WARNING INFORMATION ..........
FCC ID: K6630173X3D/IC ID: 511B-30173X3D TABLE OF CONTENTS 12 13 14 15 16 17 18 11.5 INDIVIDUAL CALL ...................................................................................................... 36 11.5.1 Setting up the Individual / Position Call Directory ......................................... 36 11.5.2 Setting up Individual Ringer ............................................................................. 37 11.5.3 Setting up Individual / Group Call Ringer ............................
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 1 GENERAL INFORMATION The Vertex Standard GX1500S is a VHF/FM transceiver designed for use in the frequency range of 156.025 to 163.275 MHz. The GX1500S can be operated from 11 to 16 VDC and has a switchable RF output power of 1 watt or 25 watts. The GX1500S is capable of DSC (Digital Selective Calling) Class D operation and an Enhanced second station RAM+ mic (CMP25 remote-control speaker/ microphone with display) or VH-310 Handset.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 4 SAFETY / WARNING INFORMATION This radio is restricted to occupational use, work related operations only where the radio operator must have the knowledge to control the exposure conditions of its passengers and bystanders by maintaining the minimum separation distance of 0.6 m (2 feet). Failure to observe these restrictions will result in exceeding the FCC RF exposure limits. Antenna Installation: The antenna must be located at least 0.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 5 FCC RADIO LICENSE INFORMATION Vertex Standard radios comply with the Federal Communication Commission (FCC) requirements that regulate the Maritime Radio Service. STATION LICENSE An FCC ship station license is no longer required for any vessel traveling in U.S. waters (except Hawaii) which is under 20 meters in length.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 6 FCC NOTICE NOTICE Unauthorized changes or modifications to this equipment may void compliance with FCC Rules. Any change or modification must be approved in writing by Marine Division of Vertex Standard. NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 7 GETTING STARTED 7.1 ABOUT VHF RADIO The radio frequencies used in the VHF marine band lie between 156 and 158 MHz with some shore stations available between 161 and 163 MHz. The marine VHF band provides communications over distances that are essentially “line of sight” (VHF signals do not travel well through objects such as buildings, hills or trees).
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 7.3 COAXIAL CABLE VHF antennas are connected to the transceiver by means of a coaxial cable – a shielded transmission line. Coaxial cable is specified by it’s diameter and construction. For runs less than 20 feet, RG-58/U, about 1/4 inch in diameter is a good choice. For runs over 20 feet but less than 50 feet, the larger RG-8X or RG-213/U should be used for cable runs over 50 feet RG-8X should be used.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 8 INSTALLATION 8.1 LOCATION The radio can be mounted at any angle.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 2. Connect the red power wire to a 13.8 VDC ±20% power source. Connect the black power wire to a negative ground. 3. If an optional remote extension speaker is to be used, refer to next section for connections. 4. It is advisable to have a Certified Marine Technician check the power output and the standing wave ratio of the antenna after installation. 8.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 8.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 8.6 CHANGING THE GPS TIME From the Factory the GX1500S shows GPS satellite time or UTC time. A time offset is needed to show the local time in your area. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Time Set” with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select time offset from UTC. See illustration below to find your offset time from UTC.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 8.7 CHANGING THE TIME LOCATION You may select the time display between local time and UTC (time GPS sends to radio). Time is displayed when GPS position (LAT/LON) is displayed by pressing the [F] key followed by the [6(NAV)] key. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Time Disp” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 8.9 OPTIONAL MMB-84 FLUSH MOUNT INSTALLATION 1. To assist in flush mounting, a template has been included. Use this template to find the mounting location. 2. Use the template to mark the location where the rectangular hole is to be cut. Confirm the space behind the dash or panel is deep enough to accommodate the transceiver (at least 6 inches or 15 cm deep). There should be at least 1/2 inch (1.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 8.10 OPTIONAL ENHANCED RAM+ SECOND STATION MIC AND/OR VH-310 HANDSET INSTALLATION The GX1500S is capable of using a Enhanced RAM+ mic (or VH-310 Handset) to remotely control the Radio, DSC, and Distress functions. In addition the GX1500S can operate as a full function intercom system. 1. Connect the Routing Cable to the one of the Remote Mic six pin connectors on the rear panel, then tighten the Cable Nut (See Figure 3). 2. Referring to Figure 4, make a 1.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D Remote Mic or External Speaker Selection By default the RAM+ (or VH-310 Handset) internal speaker is turned on, however using the RAM+ mic (or VH-310 Handset) this speaker can be turned off so the external speaker can be used. RAM+ mic procedure 1. Press and hold the [CALL/SET] key. 2. Press the [ ] or [ ] key to select “RADIO SETUP.” 3. Press the [CALL/SET] key. 4. Press the [ ] key to until “EXT SPK” is shown and press the [CALL/SET] key. 5.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 9 CONTROLS AND INDICATORS NOTE This section defines each control of the transceiver. See Figure 4 for location of controls. For detailed operating instructions refer to section “10 BASIC OPERATION.” CHANNEL SELECTOR KNOB Rotary knob used to select channels and to choose menu items (such as the DSC menu, radio setup menu, and DSC setup menu). The [UP( )] / [DOWN( )] keys on the microphone can also be used to select channels and menu items.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D Figure 4. Controls and Connectors GX1500S Page 19 Vertex Standard Co., Ltd.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D KEYPAD [SCAN(MEM)] Key Press this key to start and stop the scanning of programmed channels. Refer to section “10.12 SCANNING” for details. Secondary use Press and hold this key, memorize the selected channel into the transceiver scan memory for scanning. When repeat the same procedures (press and hold this key), DELETES the channel from the scan memory. Refer to section “10.12 SCANNING” for details.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D [ENT] Key Press the [ENT] Key to determine the menu selection and/or keypad entry. [CLR] Key Press the [CLR] Key to cancel the menu selection and/or keypad entry. [DISTRESS] Key Used to send a DSC Distress Call. To send the distress call refer to section “11.3.1 (Transmitting A DSC Distress Call).” ACCESSORY CONNECTION CABLE Connects the GX1500S to a GPS, a PA speaker, and an external speaker.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 10 BASIC OPERATION 10.1 RECEPTION 1. After the transceiver has been installed, ensure that the power supply and antenna are properly connected. 2. Press and hold the VOL/PWR knob until the radio turns on. 3. Turn the SQL knob fully counterclockwise. This state is known as “squelch off”. 4. Turn up the VOL knob until noise or audio from the speaker is at a comfortable level. 5. Turn the SQL knob clockwise until the random noise disappears.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 10.4 SIMPLEX/DUPLEX CHANNEL USE Refer to the VHF MARINE CHANNEL CHART (page 81) for instructions on use of simplex and duplex channels. NOTE All channels are factory-programmed in accordance with International, Industry Canada (Canada), and FCC (USA) regulations. Mode of operation cannot be altered from simplex to duplex or vice-versa. 10.5 INTERNATIONAL, USA, AND CANADA MODE 1. To change the modes, hold the [16/9] key and press the [WX] key.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 3. The programmed NOAA weather channels will be scanned along with the regular-programmed channels. However, scanning will not stop on a normal weather broadcast unless a NOAA alert is received. 4. When an alert is received on a NOAA weather channel, scanning will stop and the transceiver will emit a loud beep to alert the user of a NOAA broadcast. 5. Press the [WX] key to stop the alert tone and receive the weather report.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 10.8 CALLING ANOTHER VESSEL (CHANNEL 16 OR 9) Channel 16 may be used for initial contact (hailing) with another vessel. However, its most important use is for emergency messages. This channel must be monitored at all times except when actually using another channel. It is monitored by the U.S. and Canadian Coast Guards and by other vessels. Use of channel 16 for hailing must be limited to initial contact only.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D the marine operator and identify yourself by your vessel’s name, The marine operator will then ask you how you will pay for the call (telephone credit card, collect, etc.) and then link your radio transmission to the telephone lines. The marine telephone company managing the VHF channel you are using may charge a link-up fee in addition to the cost of the call. 10.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 10.12 SCANNING Allows the user to select the scan type from Memory scan or Priority scan. “Memory scan” scans the channels that were programmed into memory. “Priority scan” scans the channels programmed in memory with the priority channel. 10.12.1 Selecting the Scan Type 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “SCAN Type” in the “Radio Setup” menu with the CHANNEL selector knob. 3.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 10.12.3 Priority Scanning (P-SCAN) In the default setting, Channel 16 is set as the priority channel. You may change the priority channel to the desired channel from the Channel 16 by the Radio Setup Mode, refer to section “12.6 PRIORITY CHANNEL SET.” 1. Adjust the SQL knob until background noise disappears. 2. Select a desired channel to be scanned using the CHANNEL selector knob.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 10.14 INTERCOM OPERATION If the RAM+ Mic is connected to the GX1500S, you may communicate between the GX1500S and CMP25 RAM+ Microphones or VH-310 Handset. (Refer to section “13.2 INTERCOM OPERATION” for CMP25 RAM+ Microphone, “14.2 INTERCOM OPERATION” for CMP25 RAM+ Microphone). 10.14.1 Communication 1. Press and hold the [H/L(IC)] key, the mode is changed to “INTERCOM” mode. 2.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11 DIGITAL SELECTIVE CALLING 11.1 GENERAL WARNING This radio is designed to generate a digital maritime distress and safety call to facilitate search and rescue. To be effective as a safety device, this equipment must be used only within communication range of a shorebased VHF marine channel 70 distress and safety watch system. The range of signal may vary but under normal conditions should be approximately 20 nautical miles.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.2 MARITIME MOBILE SERVICE IDENTITY (MMSI) 11.2.1 What is an MMSI? An MMSI is a nine digit number used on Marine Transceivers capable of using Digital Selective Calling (DSC). This number is used like a telephone number to selectively call other vessels. THIS NUMBER MUST BE PROGRAMMED INTO THE RADIO TO OPERATE THE GX1500S DSC FUCTIONS. How can I obtain an MMSI assignment? Boat US offers online registration of a MMSI. Visit www.boatus.com/mmsi 11.2.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.3 DSC DISTRESS CALL The GX1500S is capable of transmitting and receiving DSC Distress messages to all DSC radios. The GX1500S may be connected to a GPS to also transmit the Latitude, Longitude of the vessel. 11.3.1 Transmitting a DSC Distress Call NOTE To be able to transmit a DSC distress call an MMSI number must be programmed, refer to section “11.2.2 Programming the MMSI.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D Transmitting a DSC Distress Call with Nature of Distress The GX1500S is capable of transmitting a DSC Distress Call with the following “Nature of Distress” categories: Undesignated, Fire, Flooding, Collision, Grounding, Capsizing, Sinking, Adrift, Abandoning, Piracy, Mob 1. Lift the red spring loaded DISTRESS cover and press the [DISTRESS] key. The “DISTRESS” menu will appear on the LCD. 2.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.3.2 Receiving a DSC Distress Call 1. When a DSC Distress call is received, an emergency alarm sounds. Then channel 16 is automatically selected. 2. Press any key to stop the alarm. 3. Turn the CHANNEL selector knob to change the display to show the position of the vessel in distress. 4 If the position of the vessel distress data does not include position, the LCD will show the display on the left.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.4.1 Transmitting an All Ships Call 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear. 2. Turn the CHANNEL selector knob to select “All Ships.” 3. Press the [ENT] key. (To cancel, turn the CHANNEL selector knob to select “Exit.”) 4. Turn the CHANNEL selector knob to select the call (“Urgency” or “Safety”). 5. Press the [ENT] key to transmit the selected type of all ships DSC call. 6.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.5 INDIVIDUAL CALL This feature allows the GX1500S to contact another vessel with a DSC VHF radio and automatically switch the receiving radio to a desired communications channel. This feature is similar to calling a vessel on CH16 and requesting to go to another channel (switching to the channel is private between the two stations). 11.5.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D pressing the [H/L(NAV)] key until the wrong character is selected, then move the channel knob to correct the entry. 12. To store the data entered, press and hold the [ENT] key. 13. To enter another individual address, repeat steps 4 through 12. 14. To exit this menu and return to radio operation mode press the [16/9] key. NOTE Selecting “Next” or “Exit” will automatically save the name and MMSI number into memory. 11.5.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D Ringer When a Individual Call or Group Call is received the radio will produce a ringing tone for 3 minutes. This selection allows the Individual Call ringer time to be changed. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appear. 2. Turn the CHANNEL selector knob to select “DSC Setup” menu. 3. Press the [ENT] key, then select “INDIV Ring” with the CHANNEL selector knob. 4. Press the [ENT] key. 5.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.5.4 Transmitting an Individual Call This feature allows the user to contact another vessel with a DSC radio. This feature is similar to calling a vessel on CH16 and requesting to go to another channel. Pre-Programmable Calling 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear. 2. Turn the CHANNEL selector knob to select “Individual.” (To cancel, select “Exit” with the CHANNEL selector knob or press the [16/9] key.) 3. Press the [ENT] key.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D Manual Calling You may enter an MMSI number manually to contact without the Setting up the Individual Directory. 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear. 2. Turn the CHANNEL selector knob to select “Individual.” (To cancel, select “Exit” with the CHANNEL selector knob or press the [16/9] key.) 3. Press the [ENT] key. The transceiver will beep, and the “Individual directory” will appear. 4.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 13. Press any key to listen to the channel to make sure it is not busy, then key the microphone and call the other vessel you desire to communicate with. 11.5.5 Receiving an Individual Call When receiving an individual call, an acknowledgment must be sent back to the calling station. The GX1500S default setting is Automatic, but has a selection that allows you to manually send a reply before the radio will switch to the requested calling channel.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.6 GROUP CALL This feature allows the user to contact a group of specific vessels (example members of a yacht club) using DSC radios with Group call function to automatically switch to a desired channel for voice communications. 11.6.1 Setting up a Group Call For this function to operate the same Group MMSI must be programmed into all the DSC VHF radios within the group of vessels that will be using this feature.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11. If a mistake was made entering in the name or the MMSI number repeat pressing the [H/L(NAV)] key until the wrong character is selected, then move the channel knob to correct the entry. 12. To store the data entered, press and hold the [ENT] key. 13. To enter another individual address, repeat steps 4 through 12. 14. To exit this menu and return to radio operation mode press the [16/9] key. 11.6.2 Transmitting a Group Call Pre-Programmable Calling 1.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D Manual Calling You may enter an MMSI number manually to contact without the Setting up the Group call number. 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear. 2. Turn the CHANNEL selector knob to select “Group.” (To cancel, select “Exit” with the CHANNEL selector knob or press [16/9] key.) 3. Press the [ENT] key. The transceiver will beep, and the “Group Directory” will appear. 4.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.6.3 Receiving a Group Call 1. When a group call is received, the GX1500S will produce a ringing alarm sound. 2. The radio automatically switches to the requested channel. 3. Press any key to stop the alarm. 4. Monitor the channel for the person calling the Group for a message. 5. If you want to respond, monitor the channel to make sure it is clear, then press the PTT on the mic and talk to the calling ship(s).
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.7 POSITION REQUEST Advancements in DSC have made it possible to poll the location of another vessel and show the position of that vessel on the display of the GX1500S. Standard Horizon has taken this feature one step further, if any Standard Horizon GPS is connected to the GX1500S, the polled position of the vessel is shown on the display of the GPS chart plotter making it easy to navigate to the location of the polled vessel.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D The GX1500S has the capability to turn off the Position Request ringer. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appear. 2. Turn the CHANNEL selector knob to select “DSC Setup” menu. 3. Press the [ENT] key, then select “DSC Beep” with the CHANNEL selector knob. 4. Press the [ENT] key. 5. Turn the CHANNEL selector knob to select “POS Request.” 6. Turn the CHANNEL selector knob to select “Off.” 7.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D NOTE If the GX1500S does not receive position data from the polled vessel, the LCD will show “NO POSITION DATA.” Manual Request You may enter an MMSI number manually to contact without the Setting up the Individual / Position Call Directory. 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear in the display. 2. Turn the CHANNEL selector knob to select “POS Request.” 3. Press [ENT] key to show the Position request directory.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.7.3 Receiving a Position Request When a position request call is received from another vessel, a ringing alarm will sound and POS REQUEST will be show in the LCD. Operation and transceiver function differs depending on “POS Reply” in the “DSC Setup” menu setting. Automatically reply: 1. When a position request call is received, a calling alarm sounds 4 times.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.8 POSITION SEND The feature is similar to Position Request, however instead of requesting a position of another vessel this function allows you to send your position to another vessel. Your vessel must have an operating GPS receiver connected for the GX1500S to send the position. 11.8.1 Setting up a Position Send Ringer The GX1500S has the capability to turn off the Position Send ringer. 1.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.8.2 Transmitting a DSC Position Send Call Pre-Programmable Calling 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear in the display. 2. Turn the CHANNEL selector knob to select the “POS Send.” 3. Press the [ENT] key to select the Individual directory. 4. Turn the CHANNEL selector knob to select a name in the directory, then press the [ENT] key. 5. Press the [ENT] key to send your position to the selected vessel.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.8.3 Receiving a DSC Position Send Call When another vessel transmits their vessels location to the GX1500S the following will happen: 1. A ringing sound will be produced when the call is received. 2. Press the [16/9] key to stop ringing 3. The position from the vessel sending it's position will be shown on the display of the radio and also transferred to any Standard Horizon GPS Chart plotter if connected. Page 52 GX1500S Vertex Standard Co., Ltd.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 11.9 MANUAL INPUTTING OF THE GPS LOCATION (LAT/LON) You may send the Latitude/Longitude of your vessel manually even if the GX1500S is not connected the GPS receiver unit. After the position is entered, transmitting a DSC Distress, Position Request, or Position Send will contain the manually entered position. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Turn the CHANNEL selector knob to select “DSC Setup” menu. 3.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 12 RADIO SETUP NOTE The optional CMP25 RAM+ mic and VH-310 Handset can also change the RADIO SETUP menu. Refer to page 74 (RAM+ mic) and page 81 (VH-310) for details. 12.1 LAMP ADJUSTING Allows setting up the backlight intensity or to turn it off. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [CALL(MENU)] key, then select “Dimmer” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [CALL(MENU)] key. 4.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 12.3 TIME OFFSET This selection sets the time offset between local time and UTC (time GPS sends to radio). Time is displayed when GPS position (LAT/LON) is displayed by pressing the [F] key followed by the [6(NAV)] key. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Time Set” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 12.4 TIME LOCATION This selection selects the time display between local time and UTC (time GPS sends to radio). Time is displayed when GPS position (LAT/LON) is displayed by pressing the [F] key followed by the [6(NAV)] key. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Time Disp.” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 12.6 PRIORITY CHANNEL SET Allows selection of the priority channel. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Priority CH” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select the channel to be a priority. 5. Press the [ENT] key to store the selected setting. 6.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 12.8 SCAN RESUME TIME This selection is used to select the time the GX1500S waits after a transmission ends before starting scanning. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “SCAN Resume” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select the desired resume time.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 12.10 WX ALERT This selection allows the radios NOAA Weather alert to be turned off. Default setting is ON. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “WX Alert” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select the desired WX alert mode. The WX alert mode can be set to “On WX,” “On SCAN,” “On SCAN/WX,” or “Off.” 5.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 12.11 CHANNEL NAME CHANGE This selection allows you to customize the name of a channel from the default name. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “CH Name” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select the channel to be named, then press the [ENT] key. 5.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 12.12 NAMING THE RADIO OR RAM+ STATIONS This selection allows you to provide the name to the radio and optional RAM+ Mic’s when connected. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Unit Name” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select the Unit (“Radio” or “RAM1”) to be named, then press the [ENT] key. 5.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 13 ENHANCED RAM+ MIC OPERATION When the RAM+ microphone is connected to the GX1500S, most VHF, DSC, setup menus and PA modes can be remotely operated. The RAM+ Mic is supplied with 23 feet (7 m) of routing cable and can be extended up to 70 feet (21 m) using three 23 feet extension cables model CT-100. The intercom operation can be used between the RAM+ Mic and the transceiver. 13.1 RAM+ MIC CONTROLS IC DW CALL SET NAV MENU WX U.I.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D POWER SWITCH (PWR) Press and hold down this key to turn to the transceiver and RAM+ Mic on and off. PTT (Push-To-Talk) SWITCH Activates transmission. [H/L] KEY Toggles between high and low power. When the [H/L] key is pressed while the transceiver is on channel 13 or 67, the power will temporarily switch from LO to HI power until the PTT is released. The [H/L] key does not function on transmit inhibited and low power only channels.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D [DW] Key Watches for a transmission on CH16 and another selected channel until either signal is received. (Dual watch) Secondary use Press and hold [DW] key, intercom operation will operate between radio and RAM+ Mic. [NAV] Key Press this key, when connected to the GPS receiver, the LCD displays Position Data and Time from the GPS. [WX] Key Immediately recalls the previously selected US NOAA weather channel from any channel location.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 13.2 INTERCOM OPERATION 13.2.1 Communication 1. Press and hold the [DW] key while in the “RADIO” mode, the mode is changed to “INTERCOM” mode. When the “INTERCOM” operation is activated, “IC” is displayed on the RAM+ Mic (and VH-310 Handset) and “INTERCOM” is displayed on the GX1500S. 2. Press the PTT switch, “TALK” is displayed. NOTE: A warning beep is emitted when the RAM+ Mic PTT switch is pressed while the transceiver microphone’s PTT switch is pressed.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 13.3 DSC/RADIO SETUP MODE The RAM+ can access the DSC / RADIO setup menu (refer to section “11 DIGITAL SELECTIVE CALLING” and section “12 RADIO SETUP MODE” for details). The LAMP, CONTRAST, and KEY BEEP menu item accessed from the RAM+ only controls the RAM+’s display and speaker. DSC/RADIO Setup mode from the RAM+: 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appears. 2. Press the [ ]/[ ] key to select “RADIO SETUP” or “DSC SETUP” menu. 3.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D MEMO GX1500S Page 67 Vertex Standard Co., Ltd.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 14 VH-310 HANDSET OPERATION When the VH-310 HANDSET is connected to the GX1500S, most VHF, DSC, setup menus and PA modes can be remotely operated as the same manner due to the front panel’s keypad of the transceiver. The VH-310 HANDSET is supplied with 23 feet (7 m) of routing cable and can be extended up to 70 feet (21 m) using three 23 feet extension cables model CT-100. The intercom operation can be used between the VH-310 HANDSET and RAM+ Mic or the GX1500S.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D [SQL] key Activates the squelch adjusting mode. Press this key to activate the squelch adjusting mode. Press the [ ] or [ ] key to adjust the squelch. [CALL(MENU)] key The [CALL(MENU)] key functions as the enter key. Secondary use Press the [CALL(MENU)] key to access the DSC OPERATION menu. The “INDIVIDUAL CALL,” “GROUP CALL,” “ALL SHIP CALL,” “POSITION REQUEST,” POSITION SEND,” STANDBY MODE,” and “CALL WAITING” functions can be accessed from the DSC OPERATION menu.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D KEYPAD [1(DIM)] key When in radio mode, this key is used to directly select channel digit “1” in a channel number. Secondary use Press the [F] key first then press the [1(DIM)] key to access the LCD Dimmer menu. Refer to section “12.1 LAMP ADJUSTING” for details. [2(MEM)] Key When in radio mode, this key is used to directly select channel digit “2” in a channel number.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D [6(NAV)] Key When in radio mode, this key is used to directly select channel digit “6” in a channel number. Secondary use Press the [F] key first then press the [6(NAV)] key, the LCD will display NAV GPS Data, Time, SOG (Speed Over Ground), and COG (Course Over Ground) when a GPS is connected to the accessory cable of the GX1500S. See section “8.4 CONNECTION OF GPS WITH NMEA OUTPUT” for details.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 14.2 INTERCOM OPERATION 14.2.1 Communication 1. Press the [F] key followed by the [5(IC)] key, the mode is changed to “INTERCOM” mode. 2. If your GX1500S is equipped with two VH-310 Handsets (or RAM+ Mics), select the station you wish to communicate (RADIO, RAM, or ALL) with the [ ]/[ ] key, then press the [ENT] key. 3.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 14.3 MANUAL INPUTTING OF THE GPS LOCATION (LAT/LON) You may send the Latitude/Longitude of your vessel manually from the VH-310 Handset even if the GX1500S is not connected the GPS receiver unit. After the position is entered, transmitting a DSC Distress, Position Request, or Position Send will contain the manually entered position. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ ] key to select “DSC SETUP” menu. 3.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 14.4 DSC/RADIO SETUP MODE The VH-310 Handset can access the DSC / RADIO setup menu (refer to section “11 DIGITAL SELECTIVE CALLING” and section “12 RADIO SETUP MODE” for details). The CONTRAST, NAV DISPLAY, KEY BEEP, and AF SELECT menu item accessed from the VH-310 Handset only controls the VH-310 Handset’s display and speaker. DSC/RADIO Setup mode from the VH-310 Handset: 1. Press and hold down the [CALL(MENU)] key until “RADIO SETUP” menu appears. 2.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 14.4.1 Changing GPS Information to Vessel position or COG Allows customizing the NAV data showing GPS Information. Factory default is “Your Vessel’s Current Position,” however, following the steps below the GPS Information can be changed to “Course Over Ground (COG).” 1. Press and hold down the [CALL(MENU)] key until “RADIO SETUP” menu appears. 2. Press the [ENT] key, then select “NAV DISPLAY” with the [ ]/[ ] key. 3. Press the [CALL(SET)MENU] key. 4.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 15 MAINTENANCE The inherent quality of the solid-state components used in this transceiver will provide many years of continuous use. Taking the following precautions will prevent damage to the transceiver. • • • • Keep the microphone connected or the jack covered at all times to prevent corrosion of electrical contacts; Never key the microphone unless an antenna or suitable dummy load is connected to the transceiver.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 15.2 FACTORY SERVICE In the unlikely event that the radio fails to perform or needs servicing, please contact the following: Standard Horizon Attention Marine Repair Department 10900 Walker Street, Cypress, CA 90630 Telephone (800) 366-4566 An “RA” Return Authorization number is not necessary to send a product in for service. Include a brief note describing the problem along with your name, return address, phone number, and proof of purchase.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 15.3 TROUBLESHOOTING CHART SYMPTOM PROBABLE CAUSE REMEDY Transceiver fails to power up. No DC voltage to the a. Check the 12VDC battery connections and transceiver, or blown the fuse. fuse. b. The PWR key needs to be pressed and held to turn the radio on. Transceiver blows fuse when connected to power supply. Reversed power wires. Check the power cable for DC voltage, or replace the fuse (6A 250V).
FCC ID: K6630173X3D/IC ID: 511B-30173X3D MEMO GX1500S Page 79 Vertex Standard Co., Ltd.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 16 CHANNEL ASSIGNMENTS Tables on the following columns list the VHF Marine Channel assignments for U.S.A. and International use. Below are listed some data about the charts. 1. VTS. Where indicated, these channels are part of the U.S. Coast Guard’s Vessel Traffic System. 2. Alpha channel numbers, that is, channel numbers followed by the letter A (such as Channel 07A) are simplex channels on the U.S.A.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 6. Marine vessels equipped with VHF radios are required to monitor Channel 16. CH 01 01A 02 03 03A 04 U C X X X X X 04A X 05 05A 06 07 X X X X 07A 08 09 X X X X X X 10 11 12 13 14 15 15 16 17 18 18A 19 19A 19A 20 X X X X X X X X X X X 20A 21 21A 22 22A X X X X X X X X X X X X X X X X GX1500S VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 156.050 160.650 Public Correspondence (Marine Operator) S 156.050 Port Operation and Commercial.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D CH 23 23A 24 25 26 27 28 60 61 U 61A X X X X X X X C X X X X X X X X 62 62A X 63 63A X 64 64A X X X 65A 66 X X 66A 67 X X X X 68 69 X X X X 70 X X 71 X X 72 73 X X X X 74 X X 65 Page 82 VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 157.150 161.750 Public Correspondence (Marine Operator) S 157.150 U.S. Government Only X D 157.200 161.800 Public Correspondence (Marine Operator) X D 157.250 161.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D CH 75 76 77 77 78 U X X X C 78A 79 79A 80 80A 81 81A X X X X X X X X 82A X X 83 83A X X X 83 84 85 86 87 88 88A WX01 WX02 WX03 WX04 WX05 WX06 WX07 WX08 WX09 WX10 X X X X X X X X X X X X X X X X X 82 X X X X X X X X X X X X X X X X VHF MARINE CHANNEL CHART S/D TX RX CHANNEL USE S 156.775 Port Operations (Inter-ship only) (1W) S 156.825 Port Operations (Inter-ship only) (1W) S 156.875 Port Operations (Inter-ship only) (1W) X S 156.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D Points of communication (Intership and between coast and ship Coast u n l e s s o t h e r w i s e Ship transmit transmit iandicated) Port Operations 01A1 156.050 156.050 63A1 156.175 156.175 052 156.250 156.250 65A 156.275 156.275 66A 156.325 156.325 123 156.600 156.600 73 156.675 156.675 3 14 156.700 156.700 74 156.725 156.725 156.875 Intership only. 774 20A12 157.000 Intership only. Navigational (Bridge-to-Bridge)5 136 156.650 156.650 677 156.375 156.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 4: Use of 156.875 MHz is limited to communications with pilots regarding the movement and docking of ships. Normal output power must not exceed 1 watt. 5: 156.375 MHz and 156.650 MHz are available primarily for intership navigational communications. These frequencies are available between coast and ship on a secondary basis when used on or in the vicinity of locks or drawbridges. Normal output power must not exceed 1 watt.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 17 WARRANTY Marine Products Limited Warranty STANDARD HORIZON (a division of Vertex Standard) warrants, to the original purchaser only, each new Marine Communications Product (“Product”) manufactured and/or supplied by STANDARD HORIZON against defects in materials and workmanship under normal use and service for a period of time from the date of purchase as follows: Fixed Mount and Portable Transceivers 1 year - if purchased before 01/01/91 3 years - if purchased be
FCC ID: K6630173X3D/IC ID: 511B-30173X3D STANDARD HORIZON will not warrant installation, maintenance or service of the Products. In all instances, STANDARD HORIZON’s liability for damages shall not exceed the purchase price of the defective Product. This warranty only extends to Products sold within the 50 States of the United States of America and the District of Columbia.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D ONLY PRODUCTS SOLD ON OR AFTER JANUARY 1, 1991 ARE COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY. ON-LINE WARRANTY REGISTRATION THANK YOU for buying Marine Division of Vertex Standard products! We are confident your new radio will serve your needs for many years! Please visit www.standardhorizon.com to register the GX1500S Marine VHF.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D 18 SPECIFICATIONS Performance specifications are nominal, unless otherwise indicated, and are subject to change without notice. 18.1 GENERAL Channels ............................................................. All USA, International and Canadian Input Voltage ....................................................................................... 13.8 VDC ±20% Current Drain Standby ....................................................................................
FCC ID: K6630173X3D/IC ID: 511B-30173X3D MEMO Page 90 GX1500S Vertex Standard Co., Ltd.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D MEMO GX1500S Page 91 Vertex Standard Co., Ltd.
FCC ID: K6630173X3D/IC ID: 511B-30173X3D Marine Division of VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. www.standardhorizon.com E M 0 Page 92 1 7 N 1 0 0 Copyright 2005 VERTEX STANDARD CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of VERTEX STANDARD CO., LTD. 0511?-?? GX1500S Vertex Standard Co., Ltd.
