FCC ID:K6630483X3D / IC:511B-30483X3S 12.8.2 Setting up a Position Request Ringer The GX1600 has the capability to turn off the Position Request ringer. 1. Press and hold down the key until “Setup Setup Menu Menu” appears. DSC / key to select “DSC 2. Press the SETUP SETUP” menu. DSC 3. Press the [SELECT] soft key, then select “DSC BEEP BEEP” with the / key. POS 4. Press the [SELECT] soft key, then select “POS Request Request” with the / key. Off 5. Press the [ENT] soft key, then select “Off Off” with / key.
FCC ID:K6630483X3D / IC:511B-30483X3S Manual Request This feature allows you to request the position of vessel by manually entering the MMSI of the ship you want to send your position to. DSC Menu 1. Press the [CALL(MENU)] key. The “DSC Menu” will appear. POS REQUEST 2. Press the / key to select “POS REQUEST”. 3. Press the [SELECT] soft key to show the “Last Individual Call”. 4. Press the / key to select the MANUAL “MANUAL MANUAL,” then press the [SELECT] soft key. / key to select the first 5.
FCC ID:K6630483X3D / IC:511B-30483X3S Manually reply: 1. When a position request call is received from another vessel, the display will be as shown in the illustration at the right. 2. A ringing alarm sounds 4 times. To send your vessels position to the requesting vessel, press the [REPLY] soft key. Or to exit from position request display, press the [QUIT] soft key. GX1600 Page 61 Vertex Standard Co., Ltd.
FCC ID:K6630483X3D / IC:511B-30483X3S 12.9 POSITION REPORT The feature is similar to Position Request, however instead of requesting a position of another vessel this function allows you to send your position to another vessel. Your vessel must have an operating GPS receiver connected for the GX1600 to send the position. NOTE To transmit a Position Report Call, a GPS must be connected to the radio and the GX1600 Individual directory must be programmed with stations you wish to send your position to.
FCC ID:K6630483X3D / IC:511B-30483X3S 6. Press the [QUIT] key to return to radio operation. Manual Calling This feature allows you to send your position to another vessel by manually entering the MMSI of the ship you want to send your position to. key. The “DSC Menu” will appear. 1. Press the DSC Menu POS RE2. Press the / key to select “POS PORT PORT”. (To cancel, press the [QUIT] soft key.) 3. Press the [SELECT] soft key. The transceiver will beep, and the “Position Report Call” menu will appear.
FCC ID:K6630483X3D / IC:511B-30483X3S 12.9.3 Receiving a DSC Position Report Call When another vessel transmits their vessels location to the GX1600 the following will happen: 1. A ringing sound will be produced when the call is received and NMEA sentences DSC, DSE are outputted so the position can be shown on a chart plotter or a computer. 2. Press the any key to stop ringing. 3. Press the / key to see position information of the station. 4. To exit to radio mode, press the [QUIT] soft key. 12.9.
FCC ID:K6630483X3D / IC:511B-30483X3S Saving a Position Report as a Waypoint The GX1600 can save a Position Report call in the radios memory as a waypoint. 1. After the Position Report call has been received: Press the [SAVE] soft key. 2. Press the / key to change the first letter in the name of the waypoint and press the [ENT] soft key. 3. Repeat step 2 until the WPT Name is entered. 4. Press and hold the [ ENT ] soft key to save the waypoint into memory. Navigating to a saved waypoint Setup 1.
FCC ID:K6630483X3D / IC:511B-30483X3S 12.10 MANUAL INPUTTING OF THE GPS LOCATION (LAT/LON) You may send the Latitude/Longitude of your vessel manually even if the GX1600 is not connected the GPS receiver unit. After the position is entered, transmitting a DSC Distress, Position Request, or Position Report will contain the manually entered position. 1. Press and hold down the key until “Setup Setup Menu Menu” appears. DSC 2. Press the / key to select “DSC SETUP SETUP” menu. PO3.
FCC ID:K6630483X3D / IC:511B-30483X3S 12.11 AUTO DSC POLLING The GX1600 has the capability to automatically track four stations programmed into the Indvidual directory. The following procedure allows the time interval between position requests to be setup. Setup 1. Press and hold down the key until “Setup Menu Menu” appears. DSC 2. Press the / key to select “DSC SETUP SETUP” menu. 3. Press the [ SELECT ] soft key, then select AUTO DSC INTERVAL “AUTO INTERVAL” with the / key. 4.
FCC ID:K6630483X3D / IC:511B-30483X3S 7. When finished, press the [QUIT] soft key numerous times to exit to the radio mode. 12.11.2 Enable/Disable Auto DSC Polling DSC Menu 1. Press the key. The “DSC Menu” will appear. AUTO POS 2. Press the / key to select “AUTO [ POLLING POLLING”, then press the SELECT] soft key. ACTIVATION / key to select the “ACTIVATION ACTIVATION”, 3. Press the then press the [SELECT] soft key. START 4.
FCC ID:K6630483X3D / IC:511B-30483X3S 12.12 DSC TEST This function is used to contact another DSC equipped vessel to ensure the DSC functions of the radio are operating. NOTE To use this feature, the radio you will be transmitting the test call to needs to have the DSC Test feature. To perform the DSC test you will need to enter a MMSI of another vessel into the Individual directory or manually enter in the MMSI using the procedure below. 12.12.
FCC ID:K6630483X3D / IC:511B-30483X3S 12.12.3 DSC Test Call by Manually Entering MMSI 1. Press the key. The “DSC Menu” will apDSC Menu pear. DSC TEST 2. Press the / key to select “DSC TEST”, then press the [SELECT] soft key. MANUAL / key to select “MANUAL MANUAL” and 3. Press the press the [SELECT] soft key. / key to select the first 4. Press the digit in the MMSI and press the [SELECT] soft key. 5. Repeat step 4 until all the numbers of the MMSI are shown on the display. 6.
FCC ID:K6630483X3D / IC:511B-30483X3S MEMO GX1600 Page 71 Vertex Standard Co., Ltd.
FCC ID:K6630483X3D / IC:511B-30483X3S 13 GENERAL SETUP The optional CMP30 (RAM3) Remote Station Microphone can also change the SETUP menu using the following procedure. 13.1 DISPLAY The GX1600 can select additional screens other than the default normal (Radio) display by using the procedure below. Setup Menu 1. Press and hold down the key until “Setup Menu” GENERAL SETUP appears, then select “GENERAL SETUP” with the / key. 2.
FCC ID:K6630483X3D / IC:511B-30483X3S 13.2 LAMP ADJUSTING This menu selection adjusts the backlight intensity. Setup Menu 1. Press and hold down the key until “Setup Menu” GENERAL SETUP appears, then select “GENERAL SETUP” with the / key. 2. Press the [SELECT] soft key, then press the / DIMMER key to select “DIMMER DIMMER”. 4. Press the / key to select the desired level HIGH OFF (“HIGH HIGH” is default). When “OFF OFF” is selected, the lamp is turned off. 5.
FCC ID:K6630483X3D / IC:511B-30483X3S 13.4 TIME OFFSET Sets the time offset between local time (with inputted offset) and UTC (without time offset) shown on the display. Time is displayed only when an optional GPS Chart Plotter is connected. Setup Menu 1. Press and hold down the key until “Setup Menu” GENERAL SETUP appears, then select “GENERAL SETUP” with the / key. 2. Press the [SELECT] soft key, then press the / TIME OFFSET key to select “TIME OFFSET”. 3.
FCC ID:K6630483X3D / IC:511B-30483X3S 13.5 TIME AREA This menu selection allows the radio to show UTC time or local time with the offset. Setup Menu 1. Press and hold down the key until “Setup Menu” GENERAL SETUP appears, then select “GENERAL SETUP” with the / key. 2. Press the [SELECT] soft key, then press the / TIME AREA key to “TIME AREA”. 3. Press the [SELECT] soft key. UTC LO4. Rotate the CHANNEL knob to select “UTC UTC” or “LOCAL CAL”. 5. Press the [ENT] soft key to store the selected setting. 6.
FCC ID:K6630483X3D / IC:511B-30483X3S 13.7 UNIT OF MEASURE Allows Navigation and AIS displays to be shown in “Knot”, “Mile/Hour” or “KiloMeter/Hour” (for speed) and “Nautical Mile” or “Kilo-Meter” (for distance). NOTE A GPS must be connected to the radio to be able to show SPEED and DISTANCE. Setup Menu 1. Press and hold down the key until “Setup Menu” GENERAL SETUP appears, then select “GENERAL SETUP” with the / key. 2.
FCC ID:K6630483X3D / IC:511B-30483X3S 13.8 MAGNETIC This selection allows customizing the GPS COG (Course Over Ground) displayed in True or Magnetic. NOTE A GPS must be connected to the radio to be able to show COG. Setup Menu 1. Press and hold down the key until “Setup Menu” GENERAL SETUP appears, then select “GENERAL SETUP” with the / key. 2. Press the [SELECT] soft key, then press the / MAGNETIC key to select “MAGNETIC MAGNETIC”. 3. Press the [SELECT] soft key. TRUE MAG4.
FCC ID:K6630483X3D / IC:511B-30483X3S 13.10 SOFT KEYS This menu item allows selection of the number of soft keys, soft key selection and how long the display will show the soft key icon after a soft key is pressed. 1. Press and hold down the key until “Setup Setup Menu GENERAL SETUP Menu” appears, then select “GENERAL SETUP” with the / key. 2. Press the [SELECT] soft key, then press the SOFT KEY / key to “SOFT KEY”. [ ] 3. Press the SELECT soft key, then press the NUMBER OF SOFT KEYS / key to “NUMBER KEYS”.
FCC ID:K6630483X3D / IC:511B-30483X3S 14 CHANNEL FUNCTION SETUP 14.1 CHANNEL GROUP This section selects a channel group from USA, Canada, and International. 1. Press and hold down the key until “Setup Setup Menu Menu” appears. CH FUNC2. Press the / key to select “CH TION SETUP SETUP”. 3. Press the [SELECT] soft key, then press the CH GROUP / key to select “CH GROUP”. 4. Press the [SELECT] soft key. 5.
FCC ID:K6630483X3D / IC:511B-30483X3S 14.3 SCAN TYPE This selection is used to select the scan mode between “Memory Scan” and “Priority Scan”. The default setting is Priority Scan. Setup Menu 1. Press and hold down the key until “Setup Menu” appears. CH FUNCTION 2. Press the / key to select “CH SETUP SETUP”. SCAN 3. Press the [SELECT] soft key, then select “SCAN TYPE TYPE” with the / key. 4. Press the [SELECT] soft key. PRIORITY SCAN / key to select “PRIORITY SCAN” 5. Press the MEMORY SCAN or “MEMORY SCAN”.
FCC ID:K6630483X3D / IC:511B-30483X3S 14.5 PRIORITY CHANNEL By default the radio priority channel is set to channel 16. This procedure allows the radio to use a different priority channel used when priority scanning. Setup Menu 1. Press and hold down the key until “Setup Menu” appears. CH FUNCTION 2. Press the / key to select “CH SETUP SETUP”. PRIORITY 3. Press the [SELECT] soft key, then select “PRIORITY CH CH” with the / key. 4. Press the [SELECT] soft key. / key to select the desired chan5.
FCC ID:K6630483X3D / IC:511B-30483X3S 14.7 CHANNEL NAME When radio mode (NORMAL) is selected, the display will show a name under the channel number. This name describes the use of the channel. The radio has the capability to customize the name by the procedure below. Example: CH69 PLEASURE to HOOKUP Setup Menu 1. Press and hold down the key until “Setup Menu” appears. CH FUNCTION / key to select “CH 2. Press the SETUP SETUP”. CH NAME 3. Press the [SELECT] soft key, then select “CH NAME” with the / key. 4.
FCC ID:K6630483X3D / IC:511B-30483X3S 14.8 STATION NAME This function allows you to change the name of the radio or second station microphone. Example: “Radio - Cabin”, “RAM1 - Flybridge”. Setup Menu 1. Press and hold down the key until “Setup Menu” appears. CH FUNCTION 2. Press the / key to select “CH SETUP SETUP”. STATION 3. Press the [SELECT] soft key, then select “STATION NAME NAME” with the / key. 4. Press the [SELECT] soft key. 5.
FCC ID:K6630483X3D / IC:511B-30483X3S 15 DSC SETUP 15.1 INDIVIDUAL DIRECTORY The GX2000/GX2100 has a DSC directory that allows you to store a vessel or person’s name and the MMSI number associated with vessels you wish to transmit Individual calls, Position Requests and Position Send transmissions. To transmit an Individual call you must program this directory with information of the persons you wish to call, similar to a cellular phones telephone directory. Setup 1.
FCC ID:K6630483X3D / IC:511B-30483X3S NEL knob to correct the entry. 12. To store the data entered, press and hold the [ENT] soft key. 13. To enter another individual address, repeat steps 5 through 12. 14. Press the [QUIT] soft key several times to return to radio operation. 15.2 INDIVIDUAL REPLY This menu item sets up the radio to automatically (default setting) or manually respond to a DSC Individual call requesting you to switch to a working channel for voice communications.
FCC ID:K6630483X3D / IC:511B-30483X3S 15.4 INDIVIDUAL RINGER The radio can be setup to ring like a telephone to alert you the radio received a DSC Individual call. The default setting is 2 minutes, however this can be changed to 15, 10 or 5 seconds with the procedure below. 1. Press and hold down the key until “Setup Setup Menu Menu” appears. DSC 2. Press the / key to select “DSC SETUP SETUP” menu. IN3. Press the [SELECT] soft key, then select “INDIVIDUAL RING RING” with the / key. 4.
FCC ID:K6630483X3D / IC:511B-30483X3S another group of vessels may program in the same Group MMSI. If this happens, simply change one or more of the last 5 digits of the Group MMSI. Setup Menu key until “Setup Menu” 1. Press and hold down the appears. DSC SETUP 2. Press the / key to select “DSC SETUP” menu. GROUP 3. Press the [SELECT] soft key, then select “GROUP DIRECTORY DIRECTORY” with the / key. ADD 4. Press the [SELECT] soft key, then select “ADD ADD” with the / key. 5. Press the [SELECT] soft key. 6.
FCC ID:K6630483X3D / IC:511B-30483X3S 15.6 POSITION REPLY The GX1600 can be set up to automatically (default setting) or manually send your position when requested by another vessel. This selection is important if you are concerned about someone polling the position of your vessel that you may not want to. In the manual mode you will see the MMSI or persons name shown on the display allowing you to choose to send your position to the requesting vessel. 1.
FCC ID:K6630483X3D / IC:511B-30483X3S 15.7 DSC BEEP This feature allows the alarm beeps to be turned on (default setting) or off when a DSC call is received. The DSC calls that can be customized are: Individual, Group, All Ships, Position Request, Position Report, Geographic Call using the procedure below: 1. Press and hold down the key until “Setup Menu” Setup Menu appears. DSC SETUP / key to select “DSC SETUP” 2. Press the menu. DSC BEEP 3.
FCC ID:K6630483X3D / IC:511B-30483X3S 16 WAYPOINTS The GX1600 is capable of storing up to 100 waypoint and navigating to them using the compass page. In addition DSC distress calls with position or a position received from a another DSC radio using DSC polling can be navigated to. 16.1 MARKING A POSITION This feature allows the radio to mark the current position of the vessel. 1. Press and hold down the key until “Setup Setup Menu Menu” appears. WAYPOINT 2.
FCC ID:K6630483X3D / IC:511B-30483X3S 16.2 ADDING A WAYPOINT Setup 1. Press and hold down the key until “Setup Menu Menu” appears. WAYPOINT 2. Press the / key to select “WAYPOINT SETUP SETUP”. WAYPOINT 3. Press the [SELECT] soft key, then select “WAYPOINT DIRECTORY DIRECTORY” with the / key. 4. Press the [ SELECT ] soft key, then select ADD “ADD ADD” with the / key. [ ] 5. Press the SELECT soft key. 6. Enter the Waypoint Name, by pressing the / key to select the first letter. 7.
FCC ID:K6630483X3D / IC:511B-30483X3S 16.3 EDITING A WAYPOINT This function allows a previously entered waypoint to be edited. 1. Press and hold down the key until “Setup Setup Menu Menu” appears. WAYPOINT 2. Press the / key to select “WAYPOINT SETUP SETUP”. WAYPOINT 3. Press the [SELECT] soft key, then select “WAYPOINT DIRECTORY DIRECTORY” with the / key. 4. Press the [ SELECT ] soft key, then select EDIT “EDIT EDIT” with the / key. 5. Press the / key to select the waypoint to be edited. 6.
FCC ID:K6630483X3D / IC:511B-30483X3S 16.5 SAVING A DSC POSITION CALL AS A WAYPOINT When a position is received from a another DSC radio the GX2000/GX2100 allows the position to be saved as a waypoint. 1. After a position has been received, press the [SAVE] soft key two times. 2. The first digit in the WPT Name will be flashing, press the / key to the first letter of the name you want to input. 3. Press the [ENT] soft key, then press the / key to select the second letter in the name. 4.
FCC ID:K6630483X3D / IC:511B-30483X3S 16.7 STOP NAVIGATING TO A WAYPOINT To stop navigating to a waypoint, press the one of the Soft keys, then press the [STOP] soft key. The radio is switched to Normal Mode. Page 94 GX1600 Vertex Standard Co., Ltd.
FCC ID:K6630483X3D / IC:511B-30483X3S MEMO GX1600 Page 95 Vertex Standard Co., Ltd.
FCC ID:K6630483X3D / IC:511B-30483X3S 17 CMP30 (RAM3) REMOTE MIC OPERATION When the Remote MIC is connected to the GX1600, all VHF, DSC, setup menus, AIS, Waypoint, Compass functions and PA/Fog modes can be remotely operated. The CMP30’s operation is same as GX1600 except the receiver audio volume setting and squelch level setting. The reason for the same operation is to make the operation of the radio and CMP30 mic easy. For specific operation of the CMP30 mic review sections in the radio manual.
FCC ID:K6630483X3D / IC:511B-30483X3S PTT (Push-To-Talk) Key Push this key to enable the transmitter. POWER ( ) Key Press and hold down this key to turn the transceiver and Remote MIC on or off. MICROPHONE The internal ClearVoice Noise Canceling mic is located here.. When transmitting, position your mouth about 1/2 to 1 inch (1.2 ~ 2.5 cm) away from the small mic hole. Speak slowly and clearly into the microphone. DISPLAY Full dot matrix display.
FCC ID:K6630483X3D / IC:511B-30483X3S [CLR/WX] Key Press to CLEAR a function or menu selection. Press and hold to select NOAA Weather channels. Press and hold again to exit Weather mode and revert to radio mode. Secondary use Hold down the [16/9] key while pressing the [WX] key to change the mode from USA to International or Canadian. [ENT] Key This key functions as the enter key. SPEAKER The internal speaker is located here. [DISTRESS] KEY Used to send a DSC Distress call.
FCC ID:K6630483X3D / IC:511B-30483X3S program the other soft keys. 7. Press the [QUIT] soft key, then press the [] KEY TIMER or [] key to select “KEY TIMER” (selects how long the soft key icon will be shown on the display after a soft key is pressed, default is 5 seconds). Then, press the [SELECT] soft key. 8. Press the [] or [] key to select the time. 9. Press the [ENT] soft key to store the selected setting. 10. Press the [QUIT] soft key several times to return to radio operation.
FCC ID:K6630483X3D / IC:511B-30483X3S 18 MAINTENANCE The inherent quality of the solid-state components used in this transceiver will provide many years of continuous use. Taking the following precautions will prevent damage to the transceiver. • • • • Keep the microphone connected or the jack covered at all times to prevent corrosion of electrical contacts; Never key the microphone unless an antenna or suitable dummy load is connected to the transceiver.
FCC ID:K6630483X3D / IC:511B-30483X3S An “RA” Return Authorization number is not necessary to send a product in for service. Include a brief note describing the problem along with your name, return address, phone number, and proof of purchase. 18.3 TROUBLESHOOTING CHART SYMPTOM PROBABLE CAUSE REMEDY Transceiver fails to power up. No DC voltage to the a. Check the 12VDC battery connections and transceiver, or blown the fuse. fuse. b. The key needs to be pressed and held to turn the radio on.
FCC ID:K6630483X3D / IC:511B-30483X3S 19 CHANNEL ASSIGNMENTS Tables on the following columns list the VHF Marine Channel assignments for U.S.A. and International use. Below are listed some data about the charts. 1. VTS. Where indicated, these channels are part of the U.S. Coast Guard’s Vessel Traffic System. 2. Alpha channel numbers, that is, channel numbers followed by the letter A (such as Channel 07A) are simplex channels on the U.S.A.
FCC ID:K6630483X3D / IC:511B-30483X3S 6. Marine vessels equipped with VHF radios are required to monitor Channel 16. 7. 156.050 MHz and 156.175 MHz are available for port operations and commercial communications purposes when used only within the U.S. Coast Guard designated Vessel Traffic Services (VTS) area of New Orleans, on the lower Mississippi River from the various pass entrances in the Gulf of Mexico to Devil’s Swamp Light at River Mile 242.4 above head of passes near Baton Rouge. 8. 156.
FCC ID:K6630483X3D / IC:511B-30483X3S 12. Use of 156.375 MHz is available for navigational communications only in the Mississippi River from South Pass Lighted Whistle Buoy “2” and Southwest Pass entrance Mid channel Lighted Whistle Buoy to mile 242.
FCC ID:K6630483X3D / IC:511B-30483X3S CH 01 01A 02 03 03A 04 U C X X X X X 04A X 05 05A 06 07 X X X X 07A 08 09 X X X X X X 10 11 12 13 14 15 15 16 17 18 18A 19 19A 19A 20 X X X X X X X X X X X 20A 21 21A 22 22A 23 23A 24 25 26 27 28 X X X X X X X X X X X X X X X X X X X X X X X GX1600 X X X X X VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 156.050 160.650 Public Correspondence (Marine Operator) S 156.050 Port Operation and Commercial. VTS in selected areas X D 156.
FCC ID:K6630483X3D / IC:511B-30483X3S CH 60 61 U C X 61A X X 62 62A X 63 63A X 64 64A X X X X 65A 66 X X 66A 67 X X X X 68 69 X X X X 70 X X 71 X X 72 73 X X X X 74 X X 75 76 77 77 78 X X X X X X 78A 79 79A X X X X 65 Page 106 VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 156.025 160.625 Public Correspondence (Marine Operator) X D 156.075 160.675 Public Correspondence (Marine Operator), Port operation, ship movement S 156.
FCC ID:K6630483X3D / IC:511B-30483X3S CH 80 80A 81 81A 81A 82 82A 83 83 83A 84 85 86 87 87A 88 88A WX01 WX02 WX03 WX04 WX05 WX06 WX07 WX08 WX09 WX10 NOTE: VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 157.025 161.625 Port operation, ship movement X X S 157.025 Commercial X D 157.075 161.675 Port operation, ship movement X S 157.075 U.S. Government Only Environmental protection operations. X S 157.075 Canadian Coast Guard Only X D 157.125 161.
FCC ID:K6630483X3D / IC:511B-30483X3S 20 WARRANTY Marine Products Limited Warranty PLEASE NOTE The following “Limited Warranty” is for valid for products that have been purchased in the United States and Canada. For limited Warranty details outside the United States, contact the dealer in your country.
FCC ID:K6630483X3D / IC:511B-30483X3S appear to be defective or not up to factory specifications. STANDARD HORIZON may, at its option, repair or replace parts or subassemblies with new or reconditioned parts and subassemblies. Parts thus repaired or replaced are warranted for the balance of the original applicable warranty. STANDARD HORIZON will not warrant installation, maintenance or service of the Products.
FCC ID:K6630483X3D / IC:511B-30483X3S Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty lasts, so the above limitations or exclusions may not apply. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. ONLY PRODUCTS SOLD ON OR AFTER JANUARY 1, 1991 ARE COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY.
FCC ID:K6630483X3D / IC:511B-30483X3S 21 RESET PROCEDURES 21.1 MEMORY CLEAR To clear the Scan memory and Preset memory: 1. Turn the radio off. 2. Press and hold in the three [Programmable] keys while turning the radio on. 21.2 MICROPROCESSOR RESETTING To clear all memories and other settings to factory defaults (except the Channel Group, MMSI number, and DSC directory information): 1. Turn the radio off. 2. Press and hold in the GX1600 and keys while turning the radio on. Page 111 Vertex Standard Co.
FCC ID:K6630483X3D / IC:511B-30483X3S 22 SPECIFICATIONS Performance specifications are nominal, unless otherwise indicated, and are subject to change without notice. 22.1 GENERAL Channels ............................................... All USA, International and Canadian Normal Input Voltage ..................................................................... 13.8 V DC Operating Voltage Range ......................................................... 11 V to 16.5 V Current Drain Standby ..................
FCC ID:K6630483X3D / IC:511B-30483X3S 22.3 RECEIVER (for Voice and DSC) Frequency Range ............................................ 156.050 MHz to 163.275 MHz Sensitivity 20 dB Quieting .............................................................................. 0.35 μV 12 dB SINAD ................................................................................. 0.25 μV Squelch Sensitivity (Threshold) ..................................................... 0.13 μV Modulation Acceptance Bandwidth ..........
FCC ID:K6630483X3D / IC:511B-30483X3S 22.6 DIMENSIONS Page 114 GX1600 Vertex Standard Co., Ltd.
FCC ID:K6630483X3D / IC:511B-30483X3S MEMO GX1600 Page 115 Vertex Standard Co., Ltd.
FCC ID:K6630483X3D / IC:511B-30483X3S MEMO Page 116 GX1600 Vertex Standard Co., Ltd.
FCC ID:K6630483X3D / IC:511B-30483X3S This device complies with part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference. Part 15.21: Changes or modifications to this device not expressly approved by Vertex Standard could void the User’s authorization to operate this device. GX1600 Page 117 Vertex Standard Co., Ltd.
FCC ID:K6630483X3D / IC:511B-30483X3S Marine Division of VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. www.standardhorizon.com E M 0 Page 118 4 4 N 1 0 Copyright 2010 VERTEX STANDARD CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of VERTEX STANDARD CO., LTD. 2 GX1600 Vertex Standard Co., Ltd.
