Operation Manual

DR-2X / DR-2XE Operating Manual 29
12. Actual remote control procedure
Remote Control for C4FM Digital
When controlling remotely with the FTM-400D
1 Please confirm that the FTM-400D DP-ID is registered on the DR-2X/DR-2XE repeater.
2 Tune the transmit frequency of the FTM-400D to the uplink frequency of the CH-B side of the DR-2X/DR-2XE.
3 Set the FTM-400D to the digital mode, then press and hold the “” key on the microphone (MH-48A6JA).
4 “REMOTE REC/PLY” is displayed on the top of the FTM-400D screen, the remote-control is available.
• To cancel the remote-control, press the “” key on the microphone (MH-48A6JA).
5 Input the 4-digits remote command by using the numeric keys (MH-48A6JA).
• Press the “” key on the microphone (MH-48A6JA) to cancel the input command at any point in the process.
6 Press the “#” key on the microphone (MH-48A6JA) to transmit the input command.
7 After transmitting the command, press the “” key on the microphone (MH-48A6JA) to return to the normal
operation.
z If the FTM-400D firmware is not compatible with the DP-ID function, update to the latest firmware to use the DP-ID
function.
z The latest firmware is available on the YAESU website.
When controlling remotely with the FTM-100D
1 Please confirm that the FTM-100D DP-ID is registered on DR-2X/DR-2XE repeater.
2 Tune the transmit frequency of the FTM-100D to the uplink frequency of the CH-B side of the DR-2X/DR-2XE.
3 Set the FTM-100D to the digital mode, then press and hold the “” key on the microphone (MH-48A6JA).
4 “REC/PLY” is displayed on the top of the screen of the FTM-100D, the remote-control is available.
• Cancelling the remote-control, press the “” key on the microphone (MH-48A6JA).
5 Input the 4-digits remote command by using the numeric key (MH-48A6JA).
• Press the “” key on the microphone (MH-48A6JA) to cancel the input command at any point in the process.
6 Press the “#” key on the microphone (MH-48A6JA) to transmit the input command.
7 After transmitting the command, press the “” key on the microphone (MH-48A6JA) to return to the normal
operation.
z If the FTM-100D firmware is not compatible with the DP-ID function, update to the latest firmware to use the DP-ID
function.
z The latest firmware is available on the YAESU website.
When controlling remotely with the FTM-3200D
1 Please confirm that the FTM-3200D DP-ID is registered on DR-2X/DR-2XE repeater.
2 Tune the transmit frequency of the FTM-3200D to the uplink frequency of the CH-B side of the DR-2X/DR-2XE.
3 Set the FTM-3200D to the digital mode, then press and hold the “” key on the microphone (MH-48A6JA).
4 “REMOTE” is displayed on the screen of the FTM-3200D, the remote-control is available.
• Cancelling the remote-control, press the “” key on the microphone (MH-48A6JA).
5 Input the 4-digits remote command by using the numeric key (MH-48A6JA).
• Press the “” key on the microphone (MH-48A6JA) to cancel the input command at any point in the process.
6 Press the “#” key on the microphone (MH-48A6JA) to transmit the input command.
7 After transmitting the command, press the “” key on the microphone (MH-48A6JA) to return to the normal
operation.
z If the FTM-3200D firmware is not compatible with the DP-ID function, update to the latest firmware to use the DP-ID
function.
z The latest firmware is available on the YAESU website.
Remote Control for Analog FM
Transmit the 4-digit DTMF codes from the transceiver to perform remote control.
1 Tune the transmit frequency to the uplink frequency of the CH-B side of the DR-2X/DR-2XE.
2 Set the transceiver to the analog FM mode.
3 While transmitting, press the “” key on the microphone, and then use the numeric keys to input the preset
4-digit remote command.