HF/50 MHz Transceiver FT DX 3000 Operating Manual YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress, CA 90630, U.S.A. YAESU UK Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K.
About This Manual . . . The FTDX3000 is a leading-edge transceiver with a number of new and exciting features, some of which may be unfamiliar to you. In order to gain the most enjoyment and operating efficiency from your FTDX3000, we recommend that you read this manual in its entirety, and keep it handy for reference as you explore the many capabilities of your new transceiver. Before using your FTDX3000, be sure to read and follow the instructions in the “Before You Begin” section of this manual.
General Description Congratulations on the purchase of your Yaesu amateur transceiver! If this is your first rig, or if Yaesu equipment is already the backbone of your station, rest assured your transceiver will provide many hours of operating pleasure for years to come. The FTDX3000 is an elite-class HF transceiver providing exceptional performance both on transmit and receive.
Table of Contents General Description...................................................... 1 Accessories & Options.................................................. 4 Supplied Accessories................................................. 4 Available Options...................................................... 5 Before You Begin........................................................... 6 Extending the Front Feet........................................... 6 Adjusting the Main Tuning Dial Torque.............
Table of Contents CW Mode Operation.................................................. 76 Setup for Straight Key (and Straight Key emulation) Operation........... 76 Using the Built-in Electronic Keyer........................ 77 Full Break-in (QSK) Operation......................... 78 Setting the Keyer Weight (Dot/Dash) Ratio....... 78 Selecting the Keyer Operating Mode................ 79 CW Convenience Features......................................... 80 Audio Peak Filter...................................
Accessories & Options Hand Microphone (MH-31B8) 1 pc Remote Control Keypad (FH-2) 1 pc DC Power Cord 1 pc Spare Fuse (25A) 1 pc RCA Plug 2 pcs Operating Manual 1 pc Warranty Card 1 pc Page 4 Supplied Accessories A07890001 AAF22X001 T9025225 Q0000074 P0091365 FT DX 3000 Operating Manual
Accessories & Options MD-200A8X MD-100A8X YH-77STA VL-1000/VP-1000 RF µTuning Kit A RF µTuning Kit B RF µTuning Kit C FC-40 DVS-6 XF-127CN CT-178 CT Cable (MDIN6P - MDIN6P 2m) Available Options Ultra-High-Fidelity Desktop Microphone Desktop Microphone Lightweight Stereo Headphone Linear Amplifier/AC Power Supply For 160 m Band For 80/40 m Bands For 30/20 m Bands External Automatic Antenna Tuner Voice Memory Unit CW Narrow Filter (C/F: 9 MHz, B/W: 300 Hz) VL-1000 Linear Amplifier Connection Cable Antenna R
Before You Begin Extending the Front Feet To elevate the front panel for easy viewing, the front left and right feet on the case bottom may be extended. Pull the front legs outward from the bottom panel. Rotate the legs counter-clockwise to lock them in the extended position. Be sure the legs have locked securely in place, because the transceiver is quite heavy and an unlocked leg could result in damage, should the transceiver move suddenly.
Before You Begin Resetting the Microprocessor Resetting Memories (Only) Use this procedure to reset (clear) the previously stored Memory channels, without affecting any configuration changes you may have made to the Menu settings. 1. Press the front panel’s [POWER] switch to turn the transceiver off. 2. While holding the [AM] button in, press and hold in the front panel [POWER] switch to turn the transceiver on. Once the transceiver comes on, you may release the buttons.
Installation and Interconnections Antenna Considerations The FTDX3000 is designed for use with any antenna system providing a 50 Ohm resistive impedance at the desired operating frequency. While minor excursions from the 50-Ohm specification are of no consequence, if the Standing Wave Ratio (SWR) present at the Antenna jack is greater than 3:1, the transceiver’s Automatic Antenna Tuner may not be able to reduce the impedance mismatch to an acceptable value.
Installation and Interconnections Grounding The FTDX3000 transceiver, like any other HF communications apparatus, requires an effective ground system for maximum electrical safety and best communications effectiveness. A good ground system can contribute to station efficiency in a number of ways: It can minimize the possibility of electrical shock to the operator. It can minimize RF currents flowing on the shield of the coaxial cable and the chassis of the transceiver.
Installation and Interconnections Connection of Antenna and Power Cables Please follow the outline in the illustration regarding the proper connection of antenna coaxial cables, as well as the DC power cable. The DC power connector for the FTDX3000 must only be connected to a DC source providing 13.8 Volts DC (±10 %), and capable of at least 23 Amperes of current. Always observe proper polarity when making DC connection: The RED DC power lead connects to the Positive (+) DC terminal.
Installation and Interconnections Connection of Microphone and Headphone FT DX 3000 Operating Manual Page 11
Installation and Interconnections Key, Keyer, and Computer-Driven Keying Interconnections The FTDX3000 includes many features for the CW operator. These functions will be detailed in the “Operation” section later. Besides the built-in Electronic Keyer, two key jacks are provided, one on the front and one on the rear panel, for convenient connection to keying devices. The Menu selections allow you to configure the front and rear panel KEY jacks according to the device you wish to connect.
Installation and Interconnections VL-1000 Linear Amplifier Interconnections Be sure that both the FTDX3000 and VL-1000 are turned off, and then follow the installation recommendations contained in the illustration. Note: Please refer to the VL-1000 Operating Manual for details regarding amplifier operation. Please do not attempt to connect or disconnect coaxial cables when your hands are wet. Set the front panel’s INPUT switch to the “INPUT2”.
Installation and Interconnections Interfacing to Other Linear Amplifiers GND EXT ALC TX GND Note The TX GND OUT pin (pin 2) of the LINEAR jack is a transistor “open collector” circuit. It is capable of handling positive relay coil voltages up to +60VDC at 200 mA or +30 VDC at 1 A. If you plan to use multiple linear amplifiers for different bands, you must provide external band switching of the “Linear Tx” relay control line from the “TX GND OUT” line at the LINEAR jack.
Plug /Connector Pinout Diagrams FT DX 3000 Operating Manual Page 15
Front Panel Controls & Switches [POWER] Switch Press and hold in this switch for one second to turn the transceiver on. Similarly, press and hold in this switch for one second to turn the transceiver off. [TUNE] Switch This is the on/off switch for the FTDX3000’s Automatic Antenna Tuner. Pressing this button momentarily places the antenna tuner in line between the transmitter final amplifier and the antenna jack (The “TUNER” icon will appear in the display). Reception is not affected.
Front Panel Controls & Switches PHONES Jack A 1/4-inch, 3-contact jack accepts either monaural or stereo headphones with 2- or 3-contact plugs. When a plug is inserted, the loudspeaker is disabled. Note: When wearing headphones, we recommend that you turn the AF Gain levels down to their lowest settings before turning power on, to minimize the impact on your hearing caused by audio “pops” during switchon.
Front Panel Controls & Switches [MIC/SPEED] Knob MIC This knob adjusts the microphone input level for (non-processed) SSB transmission. The display will show the relative microphone gain level for 3 seconds whenever this knob is turned. Advice: Adjust the [MIC/SPEED] knob while speaking in a somewhat louder than normal voice level, watch the ALC level and adjust the [MIC/SPEED] knob so that the ALC level indication just reaches the right edge of the ALC scale.
Front Panel Controls & Switches [NOTCH] Switch Pressing this button allows you to adjust the center frequency of the IF Notch filter using the [NOTCH] knob. While activated, the LED inside this button glows orange. Press the [NOTCH] knob briefly to toggle the IF Notch filter on/off. [NOTCH] Knob Press the [NOTCH] switch to turn the IF NOTCH filter on or off. Rotate the inner [NOTCH] knob to adjust the center frequency of the IF NOTCH filter.
Front Panel Controls & Switches [SCOPE] Switch Press this button momentarily to switch between the MENU, the Scope, the Scope + AF-FFT, and the Scope Memory (when there is memory) screens. Press and hold this button for more than one second to operate the decode function (when operating CW, RTTY, PSK). [SELECT] Switch This button is used to select the Menu system. [] Switch These buttons permit selection of the Menu items and settings.
Front Panel Controls & Switches [(VFO-A)RX] Indicator/Switch Press this button to activate receive on the VFO-A frequency. The LED inside the button will glow green when the transceiver is receiving on the VFOA frequency. When the transceiver receives the VFO-A frequency, pressing this button momentarily will mute the receiver, and the indicator will blink. Pressing the button once more will restore receiver operation, and the indicator will glow green steadily.
Front Panel Controls & Switches [(VFO-B)RX] Indicator/Switch This button switches the receiving frequency to VFO-B, the green LED imbedded within the button will light. When the transceiver is receiving the VFO-B frequency, pressing this button momentarily will mute the receiver and the indicator will blink. Pressing the button once more will restore receiver operation, and the indicator will glow green steadily.
Front Panel Controls & Switches [AB] Switch Press this button momentarily to transfer the frequency or memory channel data, from VFO-A to VFO-B, overwriting any previous contents in VFOB. Use this key to set both VFO-A and VFO-B to the same frequency and mode. [AB] Switch Pressing this button momentarily, exchanges the frequency or memory channel data, of VFO-A and VFO-B. [V/M] Switch This button toggles frequency control between VFOA and the memory system.
Front Panel Controls & Switches [BAND] Keys These keys allow one-touch selection of the desired Amateur band (1.8 ~ 50 MHz). The keys may also be used for direct entry of a desired operating frequency during VFO operation. [RX CLAR] Switch Pressing this button activates the RX Clarifier. This will allow you to temporarily adjust the receive frequency up to ±9.995 kHz with the [CLAR/VFOB] knob.
Front Panel Controls & Switches [CLAR/VFO-B] Knob This knob usually tunes the Clarifier offset frequency up to ±9.995 kHz. Additionally, it is used to adjust the functions selected with three buttons located around the knob. Function Switch Effect [(VFO-B)RX] Rotate the [CLAR/VFO-B] knob to adjust the VFO-B frequency, in the same step as the Main Tuning Dial knob. Rotate the [CLAR/VFO-B] knob to select the memory group. Rotate the [CLAR/VFO-B] knob to tune the VFO frequency in 1 MHz step.
Display Indications S/PO On receive, this indicates the received signal strength from S-0 to S-9+60dB. On transmit, it indicates the RF Power Output, from 0 to 150 Watts. Advice: The S and PO meter types can be changed to ANALOG or BAR type via Menu item “011 METER TYPE SELECT”. The S and PO meters can be set to the Peak-hold function (BAR type only) via Menu item “012 BAR MTR PEAK HOLD”. Block Diagram Display ANT (1, 2, 3): Indicates which antenna is selected by the front panel [ANT] button.
Display Indications [VOX] (see page 72) This is the ON or OFF indicator for the automatic voice-actuated transmitter switching in the SSB, AM, and FM modes. The controls affecting VOX operation are the Menu items “181 VOX GAIN”, “182 VOX DELAY”, and “183 ANTI VOX GAIN”. By proper adjustment of these controls, hands-free voice-actuated operation is possible. [METER] This indicator determines the function of the meter during transmission.
Display Indications [FAST] Indicator This indicator appears when the Main Tuning Dial knob’s tuning rate is set to “fast”. [LOCK] Indicator This indicator appears when the Main Tuning Dial knob is locked. Frequency Display This is the frequency display. LSB, USB, CW, AM, FM, RTTY, DATA Displays the current operating mode. Press and hold in the [MODE] button in the individual operating modes for approx.
Rear Panel ANT 1/2/3 Jacks Connect your main antenna(s) here, using type-M (PL-259) connectors and coaxial feed lines. The internal antenna tuner affects only the antenna(s) connected here, and only during transmission. Warning! The 100V RF voltage (@100 W/50 ) is applied to the TX RF section of the transceiver while transmitting. Do not touch the TX RF section while transmitting.
Rear Panel ROTATOR Jack This covered 6-pin MINI-DIN Jack accepts a cable to connect to a YAESU G-800DXA/-1000DXA/ -2800DXA Antenna Rotator (listed models are current as of early 2012). You may control the antenna azimuth rotation (and rotation speed) using the Function buttons on the front panel. TUNER Jack This 8-pin output jack is used for connection to the FC-40 External Automatic Antenna Tuner.
FH-2 Switches The supplied Remote Control Keypad FH-2 can be used to control the voice memory capability for the SSB/AM/FM modes, and the contest memory keyer for the CW mode, and the text memory for the RTTY/DATA modes. You can also play-back up to 15 seconds of incoming received audio, for verification of a missed callsign or other purposes.
Basic Operation:Receiving on Amateur Bands Before turning on the main power, please verify the following items once more. Have you made all ground connections securely? See page 9 for details. Do you have your antenna(s) connected to the rear-panel Antenna jack(s)? See page 10 for details. Is your microphone (and/or key or paddle) connected? See page 11, 12 for details. If using a linear amplifier, have all interconnections been successfully completed? See page 13, 14 for details.
Basic Operation:Receiving on Amateur Bands Here is the typical start-up procedure for normal operation: [POWER] Switch [ANT] Switch [VFO-A(RX)] Button [AF GAIN] Knob 1. Turn on the external DC power supply. 2. Press and hold in the front-panel [ON/OFF] switch until the transceiver turns on. After about five seconds (ten seconds if the optional µ-Tuning Kit is connected), the transceiver is ready for full operation. 3. The transceiver will start up on 7.000.
Basic Operation:Receiving on Amateur Bands 8. Press the [MODE] button to select the desired operating mode. Repeated presses of the [ MODE ] button step through the available selections. Pressing and holding the [ MODE ] button will toggle to the alternate mode. For example, In the LSB or USB modes, pressing and holding the [MODE ] button toggles between “LSB” and “USB” mode.
Basic Operation:Receiving on Amateur Bands Operation on 60-Meter (5 MHz) Band (U.S. and U.K. version only) The recently-released 60-meter band is covered, in the FTDX3000, by fixed memory channels. These channels are set to USB or CW, and they appear between the “last” PMS channel (“P9U”) and the first “regular” memory channel (Channel 1): 1. Press the [V/M] button once to enter the “Memory” mode; the “MCH” icon will appear in the display and a memory channel number will appear on the display.
Basic Operation:Receiving on Amateur Bands CLAR (Clarifier) Operation The [RX CLAR], [TX CLAR], [CLEAR] buttons and [CLAR/VFO-B] knob are used to offset the receive frequency, the transmit frequency, or both, from their settings on the VFO-A frequency. Four small numbers on the Multi-Display Window show the current Clarifier offset. The Clarifier controls on the FTDX3000 are designed to allow you to preset an offset (up to ±9.
Basic Operation:Receiving on Amateur Bands LOCK You may lock the setting of the Main Tuning Dial knob (for VFO-A frequency tuning) and the [CLAR/VFO-B] knob (for VFO-B frequency tuning), to prevent accidental frequency change. Main Tuning Dial knob Lock [TX CLAR(LOCK)] Button To lock the Main Tuning Dial knob, press the [(VFO-A) RX] Indicator/Switch to illuminate the imbedded green LED, then press the [LOCK] button that is located to the right of the Main Tuning Dial knob.
Convenience Features Using the VFO-B VFO-B operates similar to VFO-A. However, the [CLAR/VFO-B] knob selects the frequency for VFO-B (See box below for tuning rate). The two VFOs make simple transmit/receive split frequency operation possible. Use various combinations of the four VFO red and green transmit and receive switches to set up split frequency operation. The [SPLIT] button also sets up split frequency operation. See page 75 for details about SplitFrequency Operation.
Convenience Features Band Stack Operation The FTDX3000 utilizes a triple band-stack VFO selection technique, that permits you to store up to three favorite frequencies and modes onto each band’s VFO register. For example, you may store one frequency each on 14 MHz CW, RTTY, and USB, then recall these VFOs by successive, momentary presses of the [14] MHz band button. Each Amateur band key may similarly have up to three frequency/mode settings applied.
Convenience Features SCOPE This function displays a convenient spectrum scope for monitoring the band conditions in real time. Both strong and weak signals can be displayed in an easy-to-understand manner on the TFT screen. You can switch the spectrum scope information between VFO-B and VFO-A in an instant.
Convenience Features SCOPE FIX mode 1. Switch the operation mode to “FIX mode”. See “Switching Between CENTER/FIX Modes” on the previous page. 2. Press the [SCOPE] button momentarily to display the scope. The frequency set in Menu Mode is displayed at the leftmost start point on the screen. Width of scope display can be set in Menu Mode by individual band (See below). 130 132 134 136 138 140 142 144 146 148 150 Menu Mode FIX 1.8MHz SPAN FIX 3.5MHz SPAN FIX 5.0MHz SPAN FIX 7.
Convenience Features Rotator Control Functions When using a YAESU model G-800DXA, G-1000DXA, G-2800DXA Antenna Rotator (not supplied), it is possible to control it from the front panel of the FTDX3000. 1. Press and hold in the [ ENT ] button (one of the [BAND] key switches) for one second. The VFO-B Frequency Display area will change to the “Rotator Control” configuration. 2. Press either the [3.5(2)] button or the [7(3)] button to rotate the antenna. Pressing the [3.
Convenience Features More Frequency Navigation Techniques Keyboard Frequency Entry The Operating frequency may be entered directly into the current VFO, using the front panel [BAND] key buttons. Example: Enter 14.250.00 MHz 1. Press the [ ENT ] button to begin the direct frequency entry process. Now, beginning with the first digit of the frequency (the leftmost digit), we will enter the required digits of the frequency. 2.
Interference Rejection P.BACK (Audio Playback) from VFO-A Receiver When Audio Playback is engaged by the operator, the FTDX3000 begins automatically recording the last 15 seconds of incoming receiver audio on VFO-A. Recording is controlled with the supplied FH-2 Remote Control Keypad, plugged into the rear panel REMOTE jack. This capability is especially useful for confirming a callsign that may have been difficult to copy due to noise or QRM, etc.
Interference Rejection Receiver Operation (Front End Block Diagram) The FTDX3000 includes a wide range of special features to suppress the many types of interference that may be encountered on the HF bands. However, real world interference conditions are constantly changing, so optimum setting of the controls is somewhat of an art, requiring familiarity with the types of interference and the subtle effects of some of the controls.
Interference Rejection ATT When extremely strong local signals or high noise degrades reception, you can use the [ATT] button to insert 6, 12, or 18-dB of RF attenuation in front of the RF amplifier. [ATT] Button 1. Press the [ATT] button several times to set the desired attenuation level, per the chart below.
Interference Rejection µ-Tune Filter (Requires the optional RF µ Tuning Kit) The RF µTuning Kit provides ultra-sharp RF selectivity for the front end of the transceiver. Very high Q is made possible by the narrow-band design. Three RF µTuning Kits are available. The MTU-160 covers the 1.8 MHz band. The MTU-80/40 covers the 3.5 and 7 MHz bands. The MTU-30/20 covers 10.1 and 14 MHz bands.
Interference Rejection µ-Tune Filter (Requires the optional RF µ Tuning Kit) As you tune around on an amateur band with μ-Tune engaged, the microprocessor automatically commands the stepper motor driving the toroid core to center the filter on the current operating frequency. However, you may use the [CLAR/VFO-B] knob to skew the filter response to one side or the other of the operating frequency, to deal with heavy interference on one side.
Interference Rejection IPO (Intercept Point Optimization) The IPO feature allows the operator to optimize the characteristics of the receiver front end, depending on the current noise level and the strength of incoming signals. Press the [IPO ] button repeatedly, to set the desired characteristic of the receiver front end, according to the chart below. [IPO] Button AMP1: Amplifies the incoming signals, using a low distortion RF preamplifier (gain: approx. 10 dB).
Interference Rejection R.FLT (Roofing Filters) Narrow-band Roofing Filters of 15 kHz, 6 kHz, 3 kHz, 600 Hz, and 300 Hz (requires optional XF-127CN CW Narrow Filter) bandwidths are provided in the first IF, right after the first mixer. These filters provide protection for the 2nd mixer, DSP, and other circuitry that follow and can dramatically improve reception on a very crowded band (during a contest, etc.).
Interference Rejection IF Noise Blanker (NB) Operation The FTDX3000 includes an effective IF Noise Blanker, which can significantly reduce noise caused by automotive ignition systems. 1. Press the [NB] button briefly to reduce short duration pulse noise such as from switching transients, automobile ignitions and power lines. The “NB ON” will appear in the display to confirm that the NarrowNB is operating. 2. Press the [NB] button again to reduce longer-duration man-made pulse noise.
Interference Rejection CONTOUR Control Operation The Contour filter system provides a gentle perturbation of the IF filter passband. The Contour is set to either suppress, or boost specific frequency components, and thus enhances the sound and readability of a received signal. 1. Press the [CONT/APF] button to activate the Contour filter. The LED inside the [CONT/APF] button glows orange and the current “null” (or “peak”) position of the Contour filter will appear in the CONTOUR indicator on the display.
Interference Rejection IF SHIFT Operation (SSB/CW/RTTY/PKT/AM Modes) IF SHIFT allows you to move the DSP filter passband higher or lower, without changing the pitch of the incoming signal, and thus reduces or eliminates interference. Because the carrier tuning frequency is not varied, there is no need to re-tune the operating frequency to eliminate the interference. The total passband tuning range for the IF SHIFT system is ±1 kHz. 1. Rotate the [SHIFT] knob to the left or right to reduce the interference.
Interference Rejection WIDTH (IF DSP Bandwidth) Tuning (SSB/CW/RTTY/PKT Modes) The IF WIDTH tuning system allows you to vary the width of the DSP IF passband, to reduce or eliminate interference. Moreover, the bandwidth may actually be expanded from its default setting, should you wish to enhance incoming signal fidelity when interference on the band is low. 1. Rotate the [WIDTH] knob to the left or right to reduce the interference.
Interference Rejection NARROW (NAR) One-Touch IF Filter Selection Pressing the [NAR] button provides one-touch, mode-specific, selection of a narrow IF DSP filter setting that does not require resetting the [WIDTH] knob. Pressing the [NAR] button once more returns the bandwidth control to the WITDH/SHIFT system. The factory default bandwidths are: Operating Mode SSB CW RTTY/DATA AM FM (28/50 MHz Bands) [NAR] Switch “ON” “OFF” 200 Hz ~ 1.8 kHz 1.8 ~ 4.0 kHz (1.5 kHz) (2.4 kHz) 50 ~ 500 Hz 500 Hz ~ 2.
Interference Rejection IF NOTCH Filter Operation (SSB/CW/RTTY/DATA/AM Modes) The IF NOTCH filter is a highly effective system that allows you to slice out an interfering beat note or other carrier signal from inside the receiver passband. 1. Press the [NOTCH] button to activate the Notch filter. The LED inside the [NOTCH] button glows orange and the current “null” position of the NOTCH filter will appear in the NOTCH indicator on the display. The [NOTCH] knob functions as the Notch adjustment knob. 2.
Interference Rejection Digital NOTCH Filter (DNF) Operation The Digital NOTCH Filter (DNF) is an effective beat-canceling filter that can null out a number of interfering beat notes inside the receiver passband. Because this is an Auto-Notch feature, there is no adjustment knob associated with this filter. Advice: If a very strong interfering carrier is encountered, we recommend you first use the IF NOTCH filter, as it is the most effective notching tool in the receiver section. 1.
Interference Rejection RF Gain (SSB/CW/AM Modes) The RF Gain control provides manual adjustment of the gain levels for the receiver RF and IF stages, to account for noise and signal strength conditions at the moment. 1. The [ RF/SQL ] knob should, initially, be rotated to the fully clockwise position. This is the point of maximum sensitivity. 2. Counter-clockwise rotation of the [RF/SQL] knob will gradually reduce the system gain.
Tools for Comfortable and Effective Reception Audio Pitch Control (SSB mode) The FTDX3000 permits adjustment of the receiver audio response by shifting the carrier point during SSB operation. 1. Press the [MENU] button to enter the Menu mode. 2. Rotate the [CLAR/VFO-B] knob (or press the p/ q button) to select Menu item “105 LSB RX CARRIER” or “106 SSB USB RX CARRIER”. 3. Press the [SELECT] button. 4. Rotate the [CLAR/VFO-B] knob (or press the p/ q button) to adjust the receiver audio response as desired.
Tools for Comfortable and Effective Reception AGC (Automatic Gain Control) The AGC system is designed to help compensate for fading and other propagation effects. The AGC characteristics can be individually set for each operating mode. The basic objective of AGC is to maintain a constant audio output level once a certain minimum threshold of signal strength is achieved. Press the [AGC] button repeatedly to select the desired receiver-recovery time constant.
Tools for Comfortable and Effective Reception Adjustable Receiver Audio Filter The FTDX3000 includes an adjustable receiver audio filter, that provides precise, independent control of the low; and upper audio ranges. 1. Press the [MENU] button to enter the Menu mode. 2.
SSB/AM Mode Transmission [POWER] Switch [VFO-A(RX)] Button [MIC] Knob Main Tuning Dial Knob 1. Press the [BAND] button corresponding to the Amateur band on which you wish to operate. 2. Press the [ MODE ] button to select the operating mode. Press and hold in this button to toggle to the alternate mode. For example, In the LSB or USB modes, pressing and holding in this button toggles between “LSB” and “USB” mode.
SSB/AM Mode Transmission Advice: ALC meter deflection may be caused by excessive drive power, but also by reflected power detected in the antenna system. If the impedance presented to the transceiver is other than 50 Ohms, ALC meter action may be observed that is not related to the proper setting of the [MIC/SPEED] knob. Therefore, we recommend that you make the [MIC/SPEED] knob adjustments into a dummy load or antenna system presenting impedance very close to 50 Ohms.
Using the Automatic Antenna Tuner The Automatic Antenna Tuner (hereinafter referred to as the “ATU”) built into each FTDX3000 is designed to ensure a 50-Ohm load for the final amplifier stage of the transmitter. We recommend that the ATU be used whenever you operate on the FTDX3000. Advice: Because the ATU of the FTDX3000 is located inside the station, it only adjusts the impedance presented to the transceiver at the station end of your coaxial cable feedline.
Using the Automatic Antenna Tuner About ATU Operation Figure 1 depicts a situation where normal tuning via the ATU has been successfully completed, and the tuning data has been stored in the ATU memory. The antenna system as seen by the transmitter is shown. In Figure 2, the operator has changed frequency, and the “HI-SWR” icon has appeared. The operator presses and holds in the [TUNE] button for two seconds to begin impedance matching using the ATU.
Enhancing Transmit Signal Quality Parametric Microphone Equalizer (SSB/AM/FM mode) The FTDX3000 includes a unique Three-Band Parametric Microphone Equalizer that provides precise, independent control over the low, mid and treble ranges in your voice waveform. You may utilize one group of settings when the speech processor is off and an alternate group of settings when the speech processor is on. The speech processor feature is described in the next chapter.
Enhancing Transmit Signal Quality Parametric Microphone Equalizer (SSB/AM/FM mode) Activating the Parametric Microphone Equalizer 1. Adjust the [ MIC/SPEED ] knob, as described on page 62. 2. Press the [p/q/t/u ] button to select the “MIC EQ”, then press the [SELECT] button to select “ON”. If you use the Parametric Microphone Equalizer with the speech processor engaged, press the [p/q/t/u] buttons to select the “PROC”, then press the [SELECT] button to select “ON”.
Enhancing Transmit Signal Quality Using the Speech Processor (SSB Mode) The FTDX3000 Speech Processor is designed to increase “talk power” by increasing the average power output (via a sophisticated compression technique) and adjusting the audio quality to the menu settings (“166 P-PRMTRC EQ1 FREQ”, “169 P-PRMTRC EQ2 FREQ”, “172 P-PRMTRC EQ3 FREQ”). The result is improved intelligibility when conditions are difficult. 1. Adjust the [ MIC/SPEED ] knob, as described on [SELECT] Button page 62. 2.
Enhancing Transmit Signal Quality Adjusting the SSB Transmitted Bandwidth (SSB Mode) For transmission on SSB, a default bandwidth of 2.4 kHz is provided. This bandwidth provides reasonable fidelity along with good talk power, and is typical of the bandwidth used for decades for SSB transmission. The bandwidth may be varied by the operator, to provide different levels of fidelity or talk power, according to your preferences. Here are the steps to adjust the SSB transmit bandwidth: 1.
Transmitter Convenience Features Voice Memory (SSB/AM/FM modes: Requires optional DVS-6 Voice Memory Unit) You may utilize the Voice Memory capability of the FTDX3000 for repetitive messages. The Voice Memory system includes five memories capable of storing up to 20 seconds of voice audio each. The maximum that any memory can hold is 20 seconds.
Transmitter Convenience Features Voice Memory (SSB/AM/FM modes: Requires optional DVS-6 Voice Memory Unit) Transmitting the Recorded Message 1. Select the LSB, USB, AM, or FM mode using the front panel [MODE] buttons. 2. Press the front panel [BK-IN] button. 3. Press the FH-2 [1] ~ [5] key (whichever one you just recorded in). A “PLAY” icon will appear in the display and the message will be transmitted. Advice: You may adjust the transmit (audio) level of the recording via Menu item “016 TX OUT LEVEL”.
Transmitter Convenience Features VOX (SSB/AM/FM Modes: Automatic TX/RX Switching using Voice Control) Instead of using the microphone’s PTT switch or the front panel [MOX] switch to activate the transmitter, the VOX (Voice Operated TX/RX Control) system provides hands-free, automatic activation of the transmitter, based on voice input into the microphone. 1. Press the [p/q/t/u] button to select the “VOX”, then press the [ SELECT ] button to select “ON”.
Transmitter Convenience Features MONITOR (SSB/AM/FM modes) You may listen to the quality of your transmitted signal using the Monitor feature. 1. Press the [MONI] button. The LED inside the [MONI] button glows orange. 2. During transmission, rotate the [ MONI ] knob to adjust the audio level in the Headphones or speaker. Clockwise rotation of this knob will increase the volume level. 3. To switch the Monitor off again, press the [MONI] button once more. Confirming that the Monitor is now disengaged.
Transmitter Convenience Features Split Operation Using the TX Clarifier For split TX/RX operation in “casual” pile-ups, where the split is less than 10 kHz, the TX Clarifier (Offset Tuning) feature may be utilized. 1. Press the [TX CLAR] button. The “TX” icon will appear in the TFT display. Quick Point: The Clarifier is frequently used for receiver offset tuning.
Transmitter Convenience Features Split-Frequency Operation A powerful capability of the FTDX3000 is its flexibility in Split Frequency operation using the VFO-A and VFO-B frequency registers. This makes the FTDX3000 especially useful for high-level DX-peditions. The Split operation capability is very advanced and easy to use. 1. Press the [VFO-B(RX)] Indicator/Switch, then rotate the [CLAR/VFO-B] knob to set the desired VFO-B frequency. 2.
CW Mode Operation The powerful CW operating capabilities of the FTDX3000 permit operation using an electronic keyer paddle, a “straight key”, or a computer-based keying device. Setup for Straight Key (and Straight Key emulation) Operation Before starting, connect your key line(s) to the front and/or rear panel KEY jack(s). Be sure the [BK-IN] button is turned off for now. 1. Press the [MODE] button to engage CW operation. The “CW” and “USB” icons will appear in the display.
CW Mode Operation Using the Built-in Electronic Keyer Connect the cable from your keyer paddle to the front or rear panel KEY jack. 1. Press the [ MODE ] button to engage CW operation. The “CW” and “USB” icons will appear in the display. The LED inside the [MONI] button glows orange; and the CW monitor is activated. Advice: If you press the “CW” mode, you will engage the “CW Reverse” mode, whereby the “opposite” sideband injection is used, compared to the “normal” sideband.
CW Mode Operation Using the Built-in Electronic Keyer Full Break-in (QSK) Operation As shipped from the factory, the FTDX3000 TX/RX system for CW is configured for “Semi-break-in” operation. However, this setup may be changed to full break-in (QSK) operation using Menu item “061 CW BK-IN”. With full break-in QSK, the TX/RX switching is quick enough to hear incoming signals in the spaces between the dots and dashes of your transmission. 1. Press the [MENU] button to engage the Menu. 2.
CW Mode Operation Using the Built-in Electronic Keyer Selecting the Keyer Operating Mode The configuration of the Electronic Keyer may be customized independently for the front and rear KEY jacks of the FT DX 3000. This permits utilization of Automatic Character Spacing (ACS), if desired. This permits the use of an electronic keyer via the front jack and a straight key or computer-driven keying line via the rear panel jack. 1. Press the [MENU] button to engage the Menu. 2.
CW Convenience Features Audio Peak Filter 1. Press the [CONT/APF] button to activate the APF (Audio Peak Filter) which provides a very narrow audio bandwidth. The LED inside the [CONT/APF] button glows orange. Advice: When APF is engaged, the peak position of the APF is depicted graphically in the NOTCH indicator on the display. 2. Press the [CONT/AFP] button to disable the APF. Advice: The APF may only be activated while the transceiver is in CW mode.
CW Convenience Features CW Spotting (Zero-Beating) “Spotting” (zeroing in on another CW station) is a handy technique to ensure you and the other station are precisely on the same frequency. The Tuning Offset Indicator in the display may also be moved so you can adjust your receiver frequency to center the incoming station on the pitch corresponding to that of your transmitted signal. Using the Auto Zeroing System Press the [ p /q /t /u ] button to select the “ZIN/ SPOT”.
CW Convenience Features Using CW Reverse If you experience a difficult interference situation, where an interfering station cannot readily be eliminated, you may wish to try receiving using the opposite sideband. This may move the interfering station’s frequency in a direction that may lend itself more readily to rejection. 1. To start, let’s use a typical example where you have set the CW mode (using the default “USB” injection). 2.
CW Convenience Features CW Delay Time Setting During semi-break-in (not QSK) operation, the hang time of the transmitter, after you have finished sending, may be adjusted to a comfortable value consistent with your sending speed. This is the functional equivalent of the “VOX Delay” adjustment used on voice modes, and the delay may be varied anywhere between 30 msec and 3 seconds via Menu item “062 CW BK-IN DELAY”. 1.
CW Convenience Features Contest Memory Keyer (Using the FH-2 Remote Control Keypad) You may also utilize the CW message capability of the FTDX3000 from the FH-2 Remote Control Keypad, which plugs into the rear panel REM jack. Message Memory Five memory channels capable of retaining 50 characters each are provided (using the PARIS standard for characters and word length).
CW Convenience Features Contest Memory Keyer (Using the FH-2 Remote Control Keypad) Message Memory Programming (Using your Paddle) 1. Set the operating mode to CW. 2. Set the [BK-IN] button to “Off”. 3. Turn the internal Electronic Keyer “On”. 4. Press the [MEM] key on the FH-2. A blinking “REC” icon will appear in the display. 5. Press any of the FH-2 keys numbered [1] through [5] to begin the memory storage process, and the “REC” icon will glow steadily. 6.
CW Convenience Features Contest Memory Keyer (Using the FH-2 Remote Control Keypad) TEXT Memory The five channels of CW message memory (up to 50 characters each) may also be programmed using a text-entry technique. This technique is somewhat slower than when you send the message directly from your keyer paddle, but accuracy of character spacing is ensured. Example 1: CQ CQ CQ DE W6DXC K (20 characters) The sequential Contest Number (“Count up”) feature is another powerful feature of the CW Memory Keyer.
CW Convenience Features Contest Memory Keyer (Using the FH-2 Remote Control Keypad) Text Message Programming 1. Press the [MODE] button to set the operating mode to CW. 2. Be sure that Break-in is “Off” by pressing the [BKIN] button, if necessary. 3. Press the FH-2 [MEM] key. A blinking “REC” icon will appear in the display. 6. When the message is complete, add the “}” character at the end to signify the termination of the message. 7.
CW Convenience Features Contest Memory Keyer (Using the FH-2 Remote Control Keypad) Note: If you subsequently decide to use the “Message Memory” technique for memory storage, please note that the contents of a message stored using text input will not be transferred over when you set entry to “Message Memory technique” on a particular memory register (the Menu Mode Setting is set to “MESSAGE”).
CW Convenience Features CW Decode Alphanumeric Morse code can be decoded and displayed as text on the TFT display. 1. Press the [MODE] button to set the operating mode to CW. 2. Tune the receiver to a CW signal, then press and hold the [SCOPE] switch for one second or longer. Advice: The CW DECODE screen is displayed, and the decoded message is displayed on the screen. Note: Interfering signals, noise, phasing, code accuracy, and the like may prevent accurate message copy.
FM Mode Operation Basic Operation 1. Press the [MODE] button repeatedly, until the “FM” icon appears in the display, to select the FM operating mode. 2. Rotate the Main Tuning Dial knob to select the desired operating frequency. Pressing the microphone [UP] or [DWN] buttons will cause frequency change in 5 kHz steps. 3. Press the microphone PTT switch (or press the front panel [MOX] button) to transmit. Speak into the microphone in a normal voice level. Release the PTT or [MOX] switch to return to receive.
FM Mode Operation Repeater Operation The FTDX3000 may be utilized on 29 MHz and 50 MHz repeaters. 1. Rotate the Main Tuning Dial knob to the output frequency (downlink) from the repeater. 2. If CTCSS Tone operation is desired/needed, press the p/q/t/u button to select “TONE”, then press the [SELECT] button to engage the CTCSS mode. 3. Press the [SELECT ] button to select the desired CTCSS mode. If you just need to send the uplink encoding tone, select “ENC.” For encode/decode operation, choose “T.
FM Mode Operation Tone Squelch Operation You may also use “Tone Squelch” whereby your receiver will be kept silent until an incoming signal modulated with a matching CTCSS tone is received. The receiver squelch will then open in response to the reception of the required tone. 1. Rotate the Main tuning Dial to the output frequency (downlink) from the repeater. 2. If CTCSS Tone operation is desired/needed, press the p/q/t/u button to select “TONE”, then press the [SELECT] button to engage the CTCSS mode.
Memory Operation Convenient Memory functions The FTDX3000 contains ninety-nine regular memories, labeled “01” through “99”, nine special programmed limit memory pairs, labeled “P-1L/P-1U” through “P-9L/P-9U”, and five QMB (Quick Memory Bank) memories, labeled “C-1” through “C-5”. Each stores various settings, in addition to the VFO-A frequency and mode (See below). By default, the 99 regular memories are contained in one group; however, they can be arranged in up to six separate groups, if desired.
Memory Operation Standard Memory Operation The Standard Memory of the FTDX3000 allows storage and recall of up to 99 memories, each storing frequency, mode, and a wide variety of status information, detailed previously. Memories may be grouped into as many as six Memory Groups, and additionally you get nine pairs of band-limit (PMS) memories along with five QMB (Quick Memory Bank) memories. Memory Storage 1. Set VFO-A up with the frequency, mode, and status, the way you want to have it stored. 2.
Memory Operation Standard Memory Operation Labeling Memories You may wish to append an Alphanumeric “Tag” (label) to a memory or memories, to aid in recollection of the channel’s use (such as a club name, etc.). To do this: 1. Press the [ V/M ] button, if necessary, to enter the “Memory Mode”. A memory channel number will appear in the VFO-B frequency display. 2. Press and hold in the [V/M] button. The data stored in the currently selected memory channel will be displayed on the TFT. 3.
Memory Operation Standard Memory Operation Erasing Memory Channel Data 1. Press the [ V/M ] button, if necessary, to enter the VFO mode. 2. Press the [AM] button. The data stored in the currently selected memory channel will be displayed in the frequency field. 3. Rotate the [CLAR/VFO-B] knob to select the memory channel that you would like to erase. The memory channel number appears in the VFO-B frequency display. 4. Press the [LOCK] button to erase the contents of the selected memory channel.
Memory Operation Standard Memory Operation Memory Tune Operation You may freely tune off from any memory channel in a “Memory Tune” mode, this is similar to VFO operation. So long as you do not over-write the contents of the current memory, Memory Tune operation will not alter the contents of the memory channel. 1. Press the [V/M] button to recall any memory channel.
Memory Operation Memory Groups Memory channels may be grouped into as many as six convenient batches, for easy identification and selection. For example, you might want to designate memory groups for AM BC stations, short-wave broadcast stations, contest frequencies, repeater frequencies and PMS limits, or any other groupings you like. Each memory group is capable of holding up to 20 memory channels (except Memory Group 01: it is 19 memory channels, and the Group size is fixed).
Operation on Alaska Emergency Frequency: 5167.5 kh (U.S. Version Only) z Section 97.401(d) of the regulations governing amateur radio in the United States permit emergency amateur communications on the spot frequency of 5167.5 kHz by stations in (or within 92.6 km of) the state of Alaska. This frequency is only to be used when the immediate safety of human life and/or property are threatened, and is never to be used for routine communications.
VFO and Memory Scanning You may scan either the VFO or the memories of the FTDX3000, and the radio will halt scanning on any frequency with a signal strong enough to open the receiver squelch. VFO Scanning 1. Set the VFO-A to the frequency on which you would like to begin scanning. 2. Rotate the [RF/SQL] knob so that the background noise is just silenced. 3. Press and hold in the microphone [UP] or [DWN] key for one second to start scanning in the specified direction on the VFO frequency.
VFO and Memory Scanning Memory Scan 1. Set the transceiver up in the “Memory” mode by pressing the [V/M] button, if necessary. Advice: If you can not enter the “Memory” mode, check to see if the transceiver is in VFO-B mode (the green [VFO-B(RX)] Indicator/Switch is illuminated). If so, press the [VFO-A(RX)] Indicator/Switch to return operation to VFO-A. Now, press the [V/M] button to enter the “Memory” mode. 2. Rotate the [RF/SQL] knob so that the background noise is just silenced. 3.
PMS (Programmable Memory Scanning) To limit scanning (and manual tuning) within a particular frequency range, you can use the Programmable Memory Scanning (PMS) feature, which utilizes nine special-purpose memory pairs (“P-1L/P-1U” through “P-9L/P-9U”). The PMS feature is especially useful in helping you to observe any operating sub-band limits, which apply to your Amateur license class. 1.
Note FT DX 3000 Operating Manual Page 103
RTTY (Radio Teletype) Operation The FTDX3000 is equipped with a RTTY decode function. You can easily synchronize by aligning the marker displayed on the AF-FFT screen, together with the decode screen while receiving a signal. Mark frequency (2125 Hz), SHIFT width (170 Hz), and baudot code (US) can be changed in Menu Mode. RTTY Decode 1. Before operating, set the Menu items in the chart to the right. 2. Press the [MODE] switch, set the operating mode to “RTTY LSB”.
RTTY (Radio Teletype) Operation RTTY Text Memory Phrases (up to 50 characters) frequently used in RTTY transmission can be memorized by connecting the supplied “FH2” Remote Control Keypad to the rear panel REM jack. 5 channels can be memorized, and memorized content can be transmitted by operations on the FH-2. Text Message Programming 1. Press the [MODE] button to set the operating mode to RTTY. 2. Press the FH-2 [MEM] key. A blinking “REC” icon will appear in the display. 3.
DATA (PSK) Operation The FTDX3000 is equipped with a PSK decode function. You can easily synchronize by aligning the marker on the AFFFT screen display, together with the decode screen while receiving a signal. Decoding with this transceiver supports both general BPSK and QPSK that have error correction functions. PSK Decode 1. Press the [MODE] switch, set the operating mode to “DATA USB”.
DATA (PSK) Operation PSK Text Memory Phrases (up to 50 characters) frequently used in PSK transmissions can be recorded by connecting the supplied “FH-2” Remote Control Keypad to the rear panel REM jack. 5 memory channels may be recorded, and the memorized content can be transmitted by operations on the FH-2. Text Message Programming 1. Press the [MODE] button to set the operating mode to DATA. 2. Press the FH-2 [MEM] key. A blinking “REC” icon will appear in the display. 3.
Menu Mode The Menu system of the FTDX3000 provides extensive customization capability, so you can set up your transceiver just the way you want to operate it. The Menu items are grouped by general utilization category, and are numbered from “001 AGC” to “196 E/D PSK”. Using the Menu 1. Press the [MENU] button to engage the Menu mode. The display will show the Menu Number, the Menu Group Name and the Menu Item. 2.
Menu Mode Group AGC AGC AGC AGC DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY ※１ DISPLAY ※１ DVS ※２ DVS ※２ KEYER KEYER KEYER KEYER KEYER KEYER KEYER KEYER KEYER KEYER KEYER KEYER KEYER KEYER GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL ※３ GENERAL GENERAL GENERAL MODE-AM MODE-AM MODE-AM MODE-AM MODE-AM No.
Menu Mode Group No.
Menu Mode Group RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE TUNING TUNING TUNING TUNING TUNING TUNING TUNING TUNING TX AUDIO TX AUDIO TX AUDIO No.
Menu Mode Group No.
Menu Mode AGC Group 001 FAST DELAY Function: Sets the delay time for the AGC FAST mode. Available Values: 20 ~ 4000 msec (20 msec/step) Default Setting: 500 msec 002 MID DELAY Function: Sets the delay time for the AGC MID mode. Available Values: 20 ~ 4000 msec (20 msec/step) Default Setting: 1000 msec 003 SLOW DELAY Function: Sets the delay time for the AGC SLOW mode.
Menu Mode DVS Group 015 RX OUT LEVEL Function: Sets the audio output level from the optional DVS-6 Voice Memory Unit. Available Values: 0 ~ 100 Default: 50 Advice: If the optional DVS-6 Voice Memory Unit is not connected, this adjustment has no effect. 016 TX OUT LVL Function: Sets the microphone input level to the optional DVS-6 Voice Memory Unit Available Values: 0 ~ 100 Default: 50 Advice: If the optional DVS-6 Voice Memory Unit is not connected, this adjustment has no effect.
Menu Mode 024 NUMBER STYLE 029 CW MEMORY 4 Function: Selects the Contest Number “Cut” format for an imbedded contest number. Av a i l a b l e Va l u e s : 1 2 9 0 / A U N O / A U N T / A 2 N O / A2NT/12NO/12NT Default Setting: 1290 1290: Does not abbreviate the Contest Number AUNO: Abbreviates to “A” for “One”, “U” for “Two”, “N” for “Nine”, and “O” for “Zero”. Aunt: Abbreviates to “A” for “One”, “U” for “Two”, “N” for “Nine”, and “T” for “Zero”.
Menu Mode 036 RF SQL VR 044 uTUNE DIAL STEP Function: Selects the operation mode of the RF/SQL knob. Available Values: RF/SQL Default Setting: RF Function: Sets the transceiver computer-interface circuitry for the CAT baud rate to be used. Available Values: 4800/9600/19200/38400 bps Default Setting: 4800 bps Function: Selects the µ-TUNE mode.
Menu Mode MODE-AM Group MODE-CW Group 048 AM LCUT FREQ 054 CW PITCH Function: Selects the cutoff frequency of the lower side of the RX audio filter in the AM mode. Available Values: OFF/100 ~ 1000 Hz (50 Hz/step) Default Setting: OFF Function: Adjusts your preferred CW tone pitch. Available Values: 300 ~ 1050 Hz (50 Hz/step) Default Setting: 700 Hz 049 AM LCUT SLOPE Function: Selects the filter slope of the lower side of the RX audio filter in the AM mode.
Menu Mode 061 CW BK-IN Function: Sets the CW “break-in” mode. Available Values: SEMI/FULL Default Setting: SEMI SEMI: The transceiver will operate in the semi break-in mode. The delay (receiver recovery) time is set via the Menu item “062 CW BK-IN DELAY”. FULL: The transceiver will operate in the full break-in (QSK) mode. 062 CW BK-IN DELAY Function: Adjusts the Keying Delay (receiver recovery) time on the CW mode.
Menu Mode 075 DATA IN SELECT Function: Selects the input data to be used in the DATA mode. Available Values: DATA/USB Default Setting: DATA Selects the input data to be used in the DATA mode. DATA: Inputs the transmission data from the DATA IN (pin 1) terminal of the PACKET Jack on the rear panel while using the DATA mode. USB: Inputs the transmission data from the USB Jack on the rear panel while using the DATA mode. 076 DATA MIC GAIN Function: Sets the data input level from the TNC to the AFSK modulator.
Menu Mode 088 TONE FREQ 097 RTTY SHIFT Function: Select the desired CTCSS Tone. A total of 50 standard CTCSS tones are provided (see the CTCSS Tone Chart on Page 91). Available Values: 67.0 ~ 254.1 Hz Default Setting: 67.0 Hz Function: Selects the frequency shift for RTTY (AFSK) operation. Available Values:170/200/425/850 Hz Default Setting: 170 Hz MODE-RTTY Group 089 RTTY LCUT FREQ Function: Selects the cutoff frequency of the lower side of the RX audio filter in the RTTY mode.
Menu Mode 105 LSB RX CARRIER 114 6M CW SHAPE Function: Adjusts the receiver carrier point for the LSB mode. Available Values: -200 Hz ~ 0 ~ +200 Hz (10 Hz steps) Default Setting: 0 Function: Selects the passband characteristics of the DSP filter for the CW mode on the 50 MHz band. Available Values: SOFT / SHARP Default Setting: SOFT SOFT: Primary importance is attached to the phase of the filter factor. SHARP: Primary importance is attached to the amplitude of the filter factor.
Menu Mode 121 HF SSB SLOPE Function: Selects the shape factor of the DSP filter for the SSB mode on the HF band. Available Values: STEEP / MEDIUM / GENTLE Default Setting: MEDIUM 122 6M SSB SHAPE Function: Selects the passband characteristics of the DSP filter for the SSB mode on the 50 MHz band. Available Values: SOFT / SHARP Default Setting: SOFT SOFT: Primary importance is attached to the phase of the filter factor. SHARP: Primary importance is attached to the amplitude of the filter factor.
Menu Mode 132 FIX 3.5MHz SPAN 140 FIX 14MHz SPAN Function: Selects the desired frequency span of the FIX mode Spectrum Scope while monitoring on the 80 m amateur band. Available Values: 20 / 50 / 100 / 200 / 500 / 1000 kHz Default Setting: 500 kHz Function: Selects the desired frequency span of the FIX mode Spectrum Scope while monitoring on the 20 m amateur band. Available Values: 20 / 50 / 100 / 200 / 500 / 1000 kHz Default Setting: 500 kHz 133 FIX 5.
Menu Mode 148 FIX 28MHz SPAN 155 SSB DIAL STEP Function: Selects the desired frequency span of the FIX mode Spectrum Scope while monitoring on the 10 m amateur band. Available Values: 20 / 50 / 100 / 200 / 500 / 1000 kHz Default Setting: 1000 kHz Function: Setting of the Main Tuning Dial knob and the [CLAR/VFO-B] knob tuning speed in the SSB mode. Available Values: 1/5/10 Hz Default Setting: 10 Hz 149 FIX 50MHz Function: Selects the tuning steps for the microphone’s [UP]/[DWN] keys in the AM mode.
Menu Mode 163 PRMTRC EQ2 LEVEL 171 P-PRMTRC EQ2 FREQ Function: Adjusts the equalizer gain of the middle range of the parametric microphone equalizer. Available Values: -20 ~ 0 ~ +10 Default Setting: 0 Function: Selects the center frequency of the middle range for the parametric microphone equalizer when the speech processor is activated.
Menu Mode TX GNRL Group 177 TX MAX POWER Function: Sets a transmitter output level. Available Values: 5 ~ 100 Default Setting: 100 178 EXT AMP TUNING PWR Function: Selects a maximum output power limit for driving the input circuit of an external linear RF amplifier while tuning (while using the Remote Control function of the linear RF amplifier). Available Values: 10/20/50/100 Default Setting: 100 184 EMERGENCY FREQ TX Function: Enables Tx/Rx operation on the Alaska Emergency Channel, 5167.5 kHz.
Menu Mode 191 TX AUTO CR+LF Function: Enables/Disables the sending of the Carriage Return (CR+LF) Code while transmitting in RTTY. Available Values: ENABLE/DISABLE Default Setting: ENABLE 192 TX DIDDLE Function: Selects the transmission code when there is not a character to be transmitted. Available Values: OFF/BLANK/LTRS Default Setting: BLANK 193 BAUDOT CODE Function: Selects the Baudot Code used for the RTTY mode.
Installation of Optional Accessories CW Narrow Filter (XF-127CN) 1. Turn the FTDX3000’s [POWER] switch “OFF”, and turn off the external DC power supply. 2. Disconnect all the cables from the FTDX3000. 3. Referring to Figure 1, remove the 18 screws attaching the bottom case, then remove the bottom case. 4. Refer to Figure 2 for the mounting location for the XF-127CN. 5. Push the XF-127CN onto the holes corresponding to its assigned mounting location on the transceiver. 6.
Installation of Optional Accessories Voice Memory Unit (DVS-6) 1. Turn the FTDX3000’s [POWER] switch “OFF”, and turn off the external DC power supply. 2. Disconnect all the cables from the FTDX3000. 3. Referring to Figure 1, remove the 18 screws attaching the bottom case, then remove the bottom case. 4. Refer to Figure 2 for the mounting location for the DVS-6. 5. Push the DVS-6 onto the pins corresponding to its assigned mounting location on the transceiver.
Installation of Optional Accessories FC-40 External Automatic Antenna Tuner (for Wire Antenna) The FC-40 makes use of the control circuitry built into the transceiver, which allows the operator to control and monitor automatic operation of the FC-40, which mounts near the antenna feedpoint. The FC-40 uses specially selected, thermally stable components, and is housed in a waterproof case to withstand severe environmental conditions with high reliability.
Installation of Optional Accessories FC-40 External Automatic Antenna Tuner (for Wire Antenna) Setup the FTDX3000 The optional FC-40 Automatic Antenna Tuner provides automatic tuning of a coaxial line to present nominal 50-ohm impedance to the FTDX3000’s ANT jack. Before operation can begin, you must instruct the FTDX3000 microprocessor that the FC-40 is being used. This is done using the Menu Mode: 1. Press the [MENU] button to enter the Menu mode. 2.
Installation of Optional Accessories RF µTuning Kit The RF µTuning Kits provide ultra-sharp RF selectivity for the front end of the transceiver. Very high Q is made possible by the narrow-band design. Three RF µTuning Kits are available. The MTU-160 covers the 1.8 MHz band. The MTU-80/40 covers the 3.5 and 7 MHz bands. The MTU-30/20 covers 10.1 and 14 MHz bands.
Note FT DX 3000 Operating Manual Page 133
Specifications General Rx Frequency Range: 30 kHz - 56 MHz (operating) 1.8 MHz - 54 MHz (specified performance, Amateur bands only) Tx Frequency Ranges: 1.8 MHz - 54 MHz (Amateur bands only) Frequency Stability: ±0.
Specifications Receiver Circuit Type: Double-conversion Superheterodyne Intermediate Frequencies: 9.000 MHz/30 kHz (24 kHz for AM/FM) Sensitivity: SSB (BW: 2.4 kHz, 10 dB S+N/N) 4 µV (0.5 - 1.8 MHz) (IPO “ON”) 0.16 µV (1.8 - 30 MHz) (RF AMP 2 “ON”) 0.125 µV (50 - 54 MHz) (RF AMP 2 “ON”) AM (BW: 6 kHz, 10 dB S+N/N, 30 % modulation @400 Hz) 28 µV (0.5 - 1.8 MHz) (IPO “ON”) 2 µV (1.
Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Declaration of Conformity We, Yaesu UK Ltd. declare under our sole responsibility that the following equipment complies with the essential requirements of the Directive 1999/5/EC. Type of Equipment: Brand Name: Model Number: Manufacturer: Address of Manufacturer: HF Transceiver YAESU FTDX3000 YAESU MUSEN CO., LTD.
Copyright 2013 YAESU MUSEN CO., LTD. All rights reserved No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD.
