SPOT 250 USER MANUAL www.yagang.
1.Open the box and checking Congratulations on choosing our products! Please carefully read this instruction manual in its entirety and keep it well for using reference. This manual contained about the installation and the relative using information of this products. Please according to this manual's relative speaking when using this equipment. This equipment was made of new style, high intensity plastic . It fully shows the modem times light characteristic with beauty structure.
¾ by the plug. Never pull out the plug by tugging the power-cord. ¾ This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth. ¾ The electric connection, repairs and servicing must be carried out by a qualified employee. ¾ Do not connect this device to a dimmer pack. ¾ Do not switch the fixture on and off in short intervals as this would reduce the lamp' s life. ¾ During the initial start-up some smoke or smell may arise.
.Description of the device 1 - Moving head 2 - Yoke 3- Carry handles 4 - Base Rear panel: 5 -Power switch 6 -DMX output 7 - DMX input 8- Power cord 9 - Fuse holder LAM P:M SD 25 0/2 MSD 250 SERIAL DATA LI NK 1= GND 2= SIG.3= SIG.+ P OW ER S WI TCH FUS E LIGHTING CO NTRO L PROTOCOL:DMX51 2 S eria l n u m b er: POW ER SUP PLY T 3 .1 5A@2 30 V T 6 .
.Installion 5.1 Fitting the lamp To insert the lamp MSD 250 or MSD 250/2 open the top cover of the projector-head (see the drawing to identify which cover is top) by loosening the 3 screws on the cover. Then open the small lamp cover by loosening 2 fastening screws (see the drawing). If changing the lamp, remove the old lamp from the socket. Insert the lamp to the socket. Do not install a lamp with a higher wattage! A lamp like this generates temperatures the device is not designed for.
5.2 Lamp adjust The lamp holder is aligned at the factory. Due to differences between lamps , fine adjustment may improve light performance. Strike the lamp, open the shutter and the iris, set the dimmer intensity onto 100% and focus the light on a flat surface (wall).
5.4 Rigging the fixture DANGER TO LIFE:Please consider the respective national norms during the installation!The installation must only be carried out by an authorized dealer! ¾ The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation. ¾ The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
5.5 Connection to the mains Verify the power supply settings before applying power! If you wish to change the power supply settings,see the chapter Appendix. Connect the fixture to the mains with the enclosed power cable and plug. The earth has to be connected! The occupation of the connection-cables is as follows: Cable (EU) Brown Light blue Y ellow/Green Cable (US) Black White Green Pin International L N Live Neutral Earth 5.
6. Control Board Operation Function Table: Mode Function Condition YES--negative direction Vertical movement in positive or negative direction YES--negative direction Address code set Reset YES--reset Rainbow color wheel change color linear or stepping YES--linear DMX512 mode Automatic Slave mode Lamp on Lamp off Working mode Lamp switch Software version Lamp hot Lamp error Control board operation way: LED 1.Select working mode by pressing MODE. 2.Press ENTER to confirm the selection. 3.
7.
CHANNEL 2: TILT Value Effect 255 100 0 0 Anti-clockwise 280° rotate CHANNEL 3: PAN FINE (proportio n al) Value Effect 255 100 0 0 Fine control of tilt movement
CHANNEL 4: TILT FINE (proportional) Value Effect 255 100 0 0 Fine control of tilt movement CHANNEL 5: Speed of PAN/TILT movement Value Slow Fast Effect 255 100 0 0 Slow fast
CHANNEL 6: Lamp on/off & reset Value Effect 240-255 95-100 No function 230-239 91-94 Lamp off after 3 140-229 55-90 No function 50-54 Lamp on after 3 0-127 0-49 No function 128-255 50-100 112-127 44-49 Pink 96-111 37-43 Blue 80-95 31-36 Orange 64-79 25-30 Green 48-63 19-24 Magenta 32-47 12-18 Yellow 16-31 6-11 Red 0-15 0-5 Open/white 128-139 CHANNEL 7: Color Forwards rainbow effect from slow to fast
CHANNEL 8: Prism Value Effect Backwards rotation from slow to fast 133-255 53-100 128-132 51-52 5-127 3-50 Forwards rotation from fast to slow 0-4 0-2 No rotation No rotation CHANNEL 9: Rotating gobos Value Effect 224-255 88-100 Rotate gobo wheel continue rotation from slow to fast 160-223 63-87 Rotate gobo 5 128-159 50-62 Rotate gobo 4 96-127 37-49 Rotate gobo 3 64-95 25-36 Rotate gobo 2 32-63 12-24 Rotate gobo 1 0-31 0-11 Open/hole
CHANNEL 10:Rotating gobo index, rotating gobo rotation Value 159-255 Effect 62-100 Backwards gobo rotation from slow to fast 61-158 24-61 Forwards gobo rotation from slow to fast 0-60 0-23 Gobo indexing (0-540°) CHANNEL 11: Focus(proportional) Near Far Value Effect 255 100 0 0 close distance far distance
CHANNEL 12:Shutter, strobe Value Effect 224-255 87-100 Shutter Open 192-223 75-86 Random strobeeffect from slow to fast 160-191 62-74 Shutter Open 128-159 50-61 Pulse-effect in sequences from slow to fast 96-127 37-49 Shutter Open 64-95 25-36 Strobe-effect from slow to fast (max 10flashes/s) 32-63 12-24 Shutter Open 0-31 0-11 Shutter closed CHANNEL 13: Dimmer intensity(proportional) Value Brightest Black Effect 255 100 0 0 Brightest Black
8. Technical specifications US-model: Voltage............................AC100/110/120V , 50/60Hz Fuse................................ T 6.3 A@120V EU-model: Voltage............................AC 220/230/240V ,50/60Hz Fuse ................................
Beampath: 9. Maintenance and cleaning It is absolutely essential that the fixture is kept clean and that dust, dir t and smoke-fluid residues must not buildup on or within the fixture. Otherwise, the fixtures light-output will be significantly reduced. Regular cleaning willnot only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life.
