Datasheet

YAGEO CORPORATION ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SY
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
DESCRIPTION
Features: Low ESR, high permissible ripple current
at high frequency and long life than SC
Recommended Applications: Used switching
requlator applications in computers. Especially for
high frequency.
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 50V
Rate Capacitance Range : 1~18000µF
Capacitance Tolerance : -20 ~ +20%
Leakage Current (Max) (20°C): I=0.01CV or 3µA, whichever is greater. (After rated voltage applied
for 2 minutes)
I=Leakate Current (µA) C=nOMINAL cAPACITANCE (µF) V=Rated Voltage (V)
Dissipation Factor : at 120 Hz, 20°C
WV (V) : 6.3 10 16 25 35 50
tan
δ
: 0.22 0.19 0.16 0.14 0.12 0.10
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
WV (V) : Rated Voltage (V) 6.3 10 16 25 35 50
Impedance : Z - 25°C / Z + 20°C 4 3 2 2 2 2
Impedance : Z - 40°C / Z + 20°C 8 6 4 3 3 3
Load Life
Dø : 5ø~6.3ø 8ø~10øx12.5 10øx15~12ø 13ø~18ø
Life : 3000hrs 4000hrs 5000hrs 6000hrs
After applying rated voltage with rated ripple current for 6000 horus at 105°C, the capacitors shall
meet the following requirements.
(a) Capacitance Change : Within 25% of Initial Value
(b) Dissipation Factor : Not more than 200% of spedied value
(c) Leakage Current : Not more than the specied value
Shelf Life : After placed at 105°C without voltage applied for 1000 hours, the capacitors shall meet
the same requirement as Endurance.
[
For Low Impedance and Low E.S.R
Suitable for Output of Mother Board
]
DIAGRAM OF DIMENSIONS
Dø F dø
5.0 2.0 0.5
6.3 2.5
8.0 3.5
10.0 5.0 0.6
12.0
13.0
16.0 7.5 0.8
18.0
Dimensions : mm
Frequency coefcient
Frequency(Hz) 120 1K 10K 100K
22~180µF 0.40 0.75 0.90 1.00
220~560µF 0.50 0.85 0.94 1.00
680~1800µF 0.60 0.87 0.95 1.00
2200~3900µF 0.75 0.90 0.95 1.00
4700µF Higher 0.85 0.95 0.98 1.00
Dø <20 : Dø+0.5
Dø ≥20 : Dø+1
L ≤16 : L+1.5max
L >16 : L+2max
Dø =8&10 : L+2.5
D+0.5
Dimensions[mm]
L ≤ 12 L + 1.5Max.
13 ≤ L ≤ 15 L
L ≥ 16 L + 2.0Max.
+1.0
-0.5