Specifications

ManualsBrandsYale ManualsHome building and DecorHSA3000

Easy Fit Siren-Based Alarm

system (EF-BX)

Installation · Programming · Operating

Keep this manual safe for reference and future maintenance

Introduction Contents

Thank you for choosing the Yale Wireless Alarm System.

This simple to install system has been designed with the

user in mind.

All the components are self contained and no connections

are needed between the units. There is no need to

damage the home decor, lift carpets or run cables.

You can install up to 20 devices in this system. As well as

extra door/window contacts, PIRs and smoke detectors,

you can add keyfob remote controls and keypads for

added control convenience.

There is no need to wire into the mains supply or seek

the services of a qualiﬁed electrician. All components are

Batteries will operate for 2 years or more before they need

changing. Regular testing and battery changes (when

notiﬁed by the system) will ensure reliability and peace of

mind.

Each part of the system is ‘tamper’ protected. Any

unauthorised tampering with the system will result in an

alarm. This feature can be turned off by the user when a

battery change is required.

The system has a ﬁxed 20 second entry/exit time when

use with a Keypad. This feature allows you time to leave

the home when arming the system. Upon entering, the

feature allows time to disarm the system without causing

an alarm. Please note there are no countdown when using

a Keyfob to arm or disarm. When the siren is triggered, it

will sounds for 10 minutes.

Display extreme caution when using ladders or steps,

please follow manufacturer instructions. Be careful when

using hand and power tools and follow the manufacturers’

guidelines when using them. Take care that the correct

tools are used. Wear goggles or protective clothing where

required.

The external Siren is extremely loud, please ensure you

replace the cover and retreat to a safe distance before

testing.

Special Notes on Compatibility:

This alarm system is NOT compatible with SmartHome

Alarm, HSA6000 series and HSA3000 series accessories.

Please note the preﬁx “EF-” on the front of the part

number to indicate compatibility.

Contents

1 Location planning 2

2 Unpacking the system 3

3 Programming the system 5

4 Mounting alarm devices 6

5 Using the system 8

Adding accessories 10

Changing the batteries 11

Speciﬁcations 13

Trouble shooting 14

Recommended Installation Sequence

We recommend you follow the easy start sequence,

headings numbered 1-5.

Information and illustrations are subject to change within this

document. Yale reserves the right to alter the speciﬁcation and

product design at anytime without notice. Yale® is a registered

Summary of content (16 pages)

PAGE 1
Easy Fit Siren-Based Alarm system (EF-BX) Installation · Programming · Operating Keep this manual safe for reference and future maintenance Introduction Contents Thank you for choosing the Yale Wireless Alarm System. This simple to install system has been designed with the user in mind. Contents All the components are self contained and no connections are needed between the units. There is no need to damage the home decor, lift carpets or run cables. You can install up to 20 devices in this system.
PAGE 2
1 Location planning Work out the best places to locate the devices for maximum protection. Having chosen the locations do not mount at this stage. Operating range All devices must be within 30 metres of the siren unit and must not be mounted on or near large metal objects. Avoid obvious sources of electrical interference such as fridges and microwave ovens. Tamper switches Siren Choose a position on an external wall where the siren would be most prominent. Mount as high as possible, out of easy reach.
PAGE 3
The easiest way to get to know the system and get it up and running quickly is to get all the devices and accessories programmed on a table top before locating and mounting them. Yale Status LED Learn/Test Button Siren Cover screw PIR movement detectors 1 Remove the cover by unscrewing the single screw located on the lid. 2 Ensure the dip switches position are as shown in the diagram. If the switches are in the wrong position, please change accordingly.
PAGE 4
Keyfob remote control accessory 1 Open the battery compartment using a coin by turning the cover in the direction of the big Keyfob remote control accessory arrow so the cover small arrow is next to round dot. Slide off the battery cover, insert the battery as shown, and replace 223A/MN21 Insert CR2032 battery and replace cover. battery cover. Switch to ‘on’. kaline iefly ating move) On/Off switch / Smoke detector accessory 1 Remove the cover and insert three AA batteries.
PAGE 5
3 Programming the Siren-based system (without control panel) The siren is the heart of the system. All components must be recognised by the siren. WARNING The siren is very loud, be prepared! Take care not to activate the siren tamper switch unnecessarily. SETTING 2 1 Switch the siren’s power switch to ON • Set Dip switch 2 for interference detection. Switch On to enable and Off to disable (recommended default). (The LEDs will now flash with one short beep.
PAGE 6
4 Mounting alarm devices Before mounting the keypad and siren ensure that the siren tamper is disabled. Mounting the siren Mounting the Keypad: Ensure the tamper switch is fully depressed when the siren is mounted. If there is a gap, pack with a suitable spacing material. 1 Knock out the fixing holes. Drill holes into the wall using the fixing holes as a template. 2 Fit wall plugs into the wall and fix back cover with the screws provided. Fix front of the keypad onto the back plate.
PAGE 7
Mounting the door/window contact Frame Door/Window Sensor Yale Magnet Sensor Gap no more than 10mm 1 Find a location where the door/window contact is to be mounted. It should be mounted between the door/window frame and the door/window as shown at the top of the opening. The magnet is to go on the door/window while the sensor is to be placed on the frame. Windows can be protected in a similar way to doors. Make sure the tamper switch spring is fully depressed.
PAGE 8
5 Using the system Arm and disarm the system and practice using it. Trigger the alarm by arming the system and opening protected doors/windows and walking past PIRs. Now’s the time to set your pin code and show the rest of the family how simple it is to use. The PIRs have a built-in sleep timer to save Changing your keypad PIN code of the PIRs for 1 minute, the PIRs will become ‘ready to signal’ and movement will now be reported. The PIRs will sleep for 1 minute after reporting.
PAGE 9
Using the help button Panic alarm using keypad Activate: Press and hold panic button for 3 seconds, the LED will light briefly and the siren will be activated. Activate: Press and hold Panic button A & Panic button B together. Silence: Press disarm follows by pincode. Silence: Press and hold panic button for 10 seconds, the LED will light briefly and the siren will be silenced. i Panic alarm using keyfob Activate: Press and hold Panic button.
PAGE 10
Adding accessories to an existing system To provide additional protection you can add extra door/window contacts, PIRs, keyfob remote controls, keypad remote controls, help buttons and smoke detectors. These are available separately from your local stockist. Adding devices to an already installed system The installed system will be controlled by either a keyfob(s) or a keypad(s). Keypad 1 Enter Setting mode: Press Panic button A followed by the pincode (Indicated by a continuously flashing LED.
PAGE 11
Changing the batteries Always use alkaline batteries or the correct type of coin cells as replacements because any other battery can cause problems with the operation of the system. Typical life of batteries is two years. Ensure the correct steps are taken when changing batteries in tamper protected devices. Siren The siren will produce a series of pips and flashes when arming and disarming the system when the batteries start getting low.
PAGE 12
ASSA ABLOY Ltd. School Street, Willenhall West Midlands England, WV13 3PW ASSA ABLOY Ltd. School Street Willenhall West Midlands England WV13 3PW Model: Model: HSA3400 EF-KIT1 HSA6010 HSA3400 EF-KIT2 HSA3020 HSA6020 EF-KIT3 HSA3020 HSA3060 EF-PC HSA6021 HSA3060 HSA3010 EF-DC HSA6050 HSA3010 EF-PIR HSA3050 HSA6060 EF-PETPIR HSA3050 HSA3045 HSA6080 EF-KF HSA3045 EF-KP HSA6090 HSA3080 HSA3080 EF-BX HSA6091 HSA3030 EF-SD HSA3030 HSA3045 HSA3070 EF-PB HSA3070 EF-PANEL EN 300 220-1 / V2.3.
PAGE 13
Specifications All devices Environmental conditions -10°C to 40°C, relative humidity 70% non-condensing for all units except the external siren. Siren: -20°C to 50°C, relative humidity 95% non-condensing Radio operational range 30m in a typical domestic installation, range can vary depending on building construction, device positions and RF environment Housings ABS/polycarbonate Siren Siren output 104dBA sound pressure @ 1m minimum Radio 868MHz FM Power supply 6V, 4 x D alkaline cells. 2.
PAGE 14
Troubleshooting For online assistance, please visit: Siren Siren does not respond to keypad • Keypad low battery or bad connection. Check battery connections and polarity, if OK replace battery. • Siren batteries are completely exhausted. Check siren batteries by removing siren cover, if there is no tamper alarm when removed, replace batteries with new alkaline equivalents. • Keypad not learnt-in. If siren produces a tamper alarm when the cover is removed, and keypad is OK, learn-in the keypad.
PAGE 15
opening after test/learn button has been pressed • Batteries are completely exhausted. Change batteries with new alkaline replacements • The magnet is too far away from the door contact. Check that the gap between door contact and magnet is not greater than 10mm. Siren reset procedure • Switch the power switch to Off position. Press the learn buttons a few times to drain any residual power. • Switch DipSwitch 1 to On position • Switch the power switch to On position. Wait 5 seconds.
PAGE 16
All devices EMC Power supply 3 x AAA alkaline cells. 3 Passive infra red (PIR) detector years typical domestic service life All devices Passive infra red (PIR) detector Alarm processing Microprocessor dual edge sequential pulse EMC controlled Tested to ETS 300 683 count with pulse length discrimination Radio Components tested to EN Tested to433.92MHz ETS 300 683 Radio AM transmitter 300 220-1 Radio Components EN Power supply 4.5V,tested 3 x AAtoalkaline cells.