Specifications

ManualsBrandsYale ManualsHome building and DecorSmartHome Alarm series

Easy Fit Touch Screen

alarm system (EF-Panel)

Installation · Programming · Operating

Keep this manual safe for reference and future maintenance

Introduction Contents

Thank you for choosing the Yale Wireless Alarm System.

This simple to install system has been designed with the

user in mind.

All the components are self contained and no connections

are needed between the units. There is no need to

damage the home decor, lift carpets or run cables.

You can install up to 20 devices in this system. As well as

extra door/window contacts, PIRs and smoke detectors,

you can add keyfob remote controls and keypads for

added control convenience.

There is no need to wire into the mains supply or seek

the services of a qualiﬁed electrician. The control unit is

are powered by battery (all batteries included).

Batteries will operate for 2 years or more before they need

changing. Regular testing and battery changes (when

notiﬁed by the system) will ensure reliability and peace of

mind.

The security detectors, control panel and external siren

are ‘tamper’ protected. Any unauthorised tampering with

these items will result in an alarm. This feature can be

turned off by the user when a battery change is required.

Display extreme caution when using ladders or steps,

please follow manufacturer’s instructions.

Be careful when using hand and power tools and follow

the manufacturer’s guidelines when using them. Take care

that the correct tools are used. Wear goggles or protective

clothing where required.

The external Siren is extremely loud, please ensure you

replace the cover and retreat to a safe distance before

testing.

The dialling facilities must only be used with persons who

have consented to being contacted by the system.

The system is not to be used to make 999 emergency

calls directly. Yale do not hold responsibility for any actions

taken by emergency services for incorrect use of the

dialling facility.

Special Notes on Compatibility:

This alarm system is NOT compatible with SmartHome

Alarm, HSA6000 series and HSA3000 series accessories.

Please note the preﬁx “EF-” on the front of the part

number to indicate compatibility.

Information and illustrations are subject to change within this

document. Yale reserves the right to alter the speciﬁcation and

product design at anytime without notice. Yale® is a registered

Contents

1 Location planning 2

2 Unpack all the parts 4

3 First Time Easy Install 6

4 Mounting alarm devices 8

5 Control Panel Menu System in Detail 11

6 Using the System 17

Adding and using Accessories 20

Changing the batteries 22

Troubleshooting 24

Sensor response table 27

Speciﬁcations 28

Recommended Installation Sequence

We recommend you follow the simple install

sequence, headings numbered 1-6.

Summary of content (32 pages)

PAGE 1
Easy Fit Touch Screen alarm system (EF-Panel) Installation · Programming · Operating Keep this manual safe for reference and future maintenance Introduction Contents Thank you for choosing the Yale Wireless Alarm System. This simple to install system has been designed with the user in mind. Contents All the components are self contained and no connections are needed between the units. There is no need to damage the home decor, lift carpets or run cables. You can install up to 20 devices in this system.
PAGE 2
1 Location planning Work out the best places to locate the devices for maximum protection. Having chosen the locations do not mount at this stage. Home and Away Mode Planning The home arming mode allows the premises to be part armed so that no one can get inside without warning the occupier, yet the person already inside the house can move freely without triggering the alarm.
PAGE 3
Smoke detector • Mount in the middle of the ceiling at the top of a stairwell, or on the centre of hallway ceilings where smoke would most likely be detected. • Do not mount in corners or above cooking appliances and heaters. • Install additional detectors if there are closed doors preventing smoke from reaching detectors. Siren Choose a position on an external wall where the siren would be most prominent. Mount as high as possible, out of easy reach.
PAGE 4
2 Unpack all the parts Backspace/Return Up Down Siren OK WARNING Siren The siren is very loud, be prepared! Take care not to activate the siren tamper switch unnecessarily. Text Display 1 Remove the cover by unscrewing the single screw located on the lid. Power LED 2 Power switch to ON position. Fault LED Microphone Menu Arm Home Arm Disarm Numeric keys Control unit Unpack the kit content on a table. Remove the mounting plate (if fitted) from the control unit by sliding plate downwards.
PAGE 5
Keyfob remote control accessory Door/window contacts 1 Pull out the battery saver tab on the side to activate Keypad remote control the battery. Yale Remove the cover and insert the 3 AAA alkaline batteries as shown. The ‘Tx’ LED will flash briefly while components initialise. Please note, the HomeLED button on the operating panel and the jumper switch inside (do not move) Learn/Test have no function on this model.
PAGE 6
3 First Time Easy Set-up The installation guide will provide you with prompts to easily set-up the system. • Any omissions or mistakes can be rectified i later. Once the first time install has been successfully completed it will not be shown again. • More advanced programming can be done at a later stage including adding and naming sensors and changing various settings. Connect the mains power adaptor to the control panel (in the intended location).
PAGE 7
Next, the screen will display: .Exit setup Repeat Setup Upon selecting “Exit Setup”, you will now be prompted with: mount devices, see Manual Error Condition (Upon selecting Exit setup) If there are no device/accessory (accidentally deleted) in the system and you selected “Exit Setup”, you will be prompt with “Please add at least one device”. i Please add at least one device Please leave it on this screen and proceed to mount all your devices (see Chapter 4).
PAGE 8
4 Post Installation/Mounting Devices Note: Tamper is disabled during initial set-up. For details on disabling tamper see Section 6 Control Unit Mounting Wall Mounting Using the two holes on the mounting back plate, mark the position of the holes. Drill two holes and fix with the screws and plugs provided. Hook the control panel onto the plate. Ensure that the control unit is fitted at approximately chest height where the display can be easily seen and the keypad convenient to operate.
PAGE 9
1 Find a location on the door/window where you would like the device to be mounted. The sensor should be on the frame while the magnet should be on the door/window. Once mounted make sure the tamper switch spring is fully depressed. gap between the magnet and sensor should i The be no more than 10mm when closed (maybe Battery tab Wall fixing knockouts x2 Corner fixing knockouts x4 2 Drill holes into the wall using the knockout holes on the base as a template.
PAGE 10
About your alarm system (default settings) All accessories were pre-set to “entry” attributes. i To change the property of individual sensor (i.e. Burglar attribute where the individual sensor will instantly alarm when triggered), see Chapter 5, Devices, Edit Devices. When the system is first armed, user will have 30 seconds to exit the building. System will ignore any sensors triggering in this duration. Home arming is disabled by default. If you need Home arming function, see Chapter 5, Homearm set.
PAGE 11
5 Control Panel Menu System in Detail System Test Entering Programming Mode The programming mode is for you to configure the system, and make any changes to the pre-set functions. If the system is in Disarmed (Alarm off) mode, follow the steps below to enter the programming mode. 1 Press ‘menu’ key on the control panel. The screen will prompt you to enter the PIN code. P - M o d e P - C o d e e n . . t . e . r 2 Key in your PIN code within 30 seconds. Note • Press P to clear the entered PIN.
PAGE 12
If you press any test/learn button on any learnt-in sensor (confirm by pressing 3), these sensors will be ignored during the Home Arm mode. Repeat this step to ignore additional sensors. Devices Select ‘Devices’ in the main programming menu to add or remove a device. From here you will be able to view a list of all the devices being installed and you can add or delete devices. The following items can be selected.
PAGE 13
• A 24 Hour door contact is active all of the time and does not have to be armed or disarmed, if triggered a burglar alarm will be activated immediately. Emergency • An emergency device is active all of the time does not have to be armed or disarmed, if triggered an emergency alarm will be activated immediately. Edit Devices To edit all of the devices that has already been installed, choose ‘edit devices’ in the device +/menu. All of the devices included in the system will be displayed.
PAGE 14
Log The alarm log memorises the last 30 system events including: · All alarm events with device names and type · All fault warning events · All arming and disarming events • The logged events are displayed in reversed chronological order (most recent event first). • The log is marked with a ‘start’ label before the most recent entry and ‘end’ after the oldest entry. To view log: 1 Select the Log menu and press 3.
PAGE 15
second increments. • 30 seconds is the factory default. Entry Sound The control unit will beep during the entry delay period as an entry warning, you can switch the sound on and off with this setting. • Entry sound on is the factory default. Exit Sound The control unit will beep during the exit delay period as an exit warning, you can switch the sound on and off with this setting. • Exit sound on is the factory default.
PAGE 16
• Warning on is the factory default. Time The control unit uses a 24 hour clock. The time is set by using the pq keys and confirmed by pressing the 3 key. Date The day and month are set by using the pq keys and confirmed by pressing the 3 key. Supervision Enable or disable supervision detection on the control panel. PIR, Door Contact, Smoke Detector and Siren can be monitored for outage using this feature.
PAGE 17
6 Using the System Arm and disarm the system and practice using it. Trigger the alarm by arming the system and opening protected door/windows and walking past PIRs. Now is the time to show the rest of the family how simple it is to use. PIRs have a built-in sleep timer to save i The battery power. If there is no movement in front of the PIRs for 1 minute, the PIRs will become ‘ready to signal’ and movement will now be reported. The PIRs will sleep for 1 minute after reporting.
PAGE 18
or away entry are triggered, the alarm will be activated immediately. Stop the Alarm and Alarm Display During an alarm, the control panel and outside siren will sound and dial the emergency phone number. The control unit will display “ALARM! ALARM!” to notify the user. Stopping the Alarm 1 Press the disarm key and enter a user code on the control unit or keypad. The control unit will sound a long beep and display the device that caused the alarm.
PAGE 19
i Disabling the system tamper Before mounting it is important to disable the siren and system tamper to avoid the siren sounding an alarm. 1 Press the Menu key and enter a user PIN code followed by 3. 2 The control unit is now in programming mode, Select Devices, then Program Siren and Siren Tamp. Off using the pq3 keys. 3 Press 3 when in the Siren Tamp. Off menu and the control unit will beep followed by an acknowledgement pip from the siren.
PAGE 20
Adding and using Accessories To provide additional protection you can add extra door/window contacts, PIRs, keyfob remote controls, keypad remote controls, help buttons and smoke detectors. These are available separately from your local stockist. Preparation Keypad See section 2 for battery insertion, activation and part identification. See also section 1 and section 4 for installation details and suggestions.
PAGE 21
Using your keypad • The keypad can be used to Away Arm and Home Arm the system using the buttons as shown. • The system is disarmed by pressing the disarm button followed by any user code, similar to using the control unit keypad. • An emergency alarm can be activated by pressing the panic A and B buttons simultaneously. Deactivate you panic event by pressing disarm button followed by any user code. • The keypad uses the same user pincodes programmed into the control unit for disarming.
PAGE 22
Changing the Batteries Always use alkaline batteries or the correct type of coin cells as replacements because any other battery can cause problems with the operation of the system. Typical life of batteries is two years or more. Ensure the correct steps are taken when changing batteries in tamper protected devices. Control unit low battery Indication The control unit will display all device low battery conditions with the exception of the siren.
PAGE 23
Help button battery change Keyfob battery change When the battery is low the LED will glow dimly when any key is pressed. The battery is changed as follows: 1 Using a coin turn the battery cover anticlockwise to the unlocked position and remove cover and battery. 2 Insert new CR2032 coin cell with the + side uppermost. 3 Replace battery cover. When the battery is low the LED will glow dimly when the button is pressed.
PAGE 24
Troubleshooting For online assistance, please visit: Siren Siren does not respond to arming or disarming • Siren batteries are completely exhausted. Check siren batteries by removing siren cover, if there is no tamper alarm when removed, replace batteries with new alkaline equivalents. • Siren not learnt-in. If siren produces a tamper alarm when the cover is removed and siren is OK, learn-in the siren. • Siren out of range.
PAGE 25
_____________________________________________ RED triangle LED illuminates and warning beeps (every 30 seconds if enabled) • There is a fault condition in your alarm system. Note: this may a simple fault that can easily be rectified, for example replacing low batteries in an internal PIR (movement) sensor. • Please view the ‘fault log’ in the control panel to determine what the issue is. This is the first option in the programming menu.
PAGE 26
5 Press the P key. 6 All programmed parameters are reset to factory default setting. All learnt sensors will be kept. 7 If more than 17 incorrect keys are entered, then the unit will revert to normal Alarm On mode. _____________________________________________ Jamming/Interference detection User can enable Jamming/interference detection should they feel it is a risk. Detection via control panel From the panel’s menu system, select: Adv. Setting -> Jamming Det, Enable.
PAGE 27
Alarm sensor response table Disarm Away Arm Home Arm Exit Away Arm Entry Home Arm Entry Burglar No action Instant Burglar alarm Instant Burglar alarm No action No action No action Home Omit No action Instant Burglar alarm No action No action No action No action Entry Door Chime Start Entry Timer Start Entry Timer No action No action No action Away Entry Door Chime Start Entry Time No action No action No action No action 24 Hour Instant Burglar Alarm Instant Burglar Alarm
PAGE 28
Specifications All devices Environmental conditions -10°C to 40°C, relative humidity 70% non-condensing for all units except the external siren.
PAGE 29
ASSA ABLOY Ltd. School Street, Willenhall West Midlands England, WV13 3PW ASSA ABLOY Ltd. School Street Willenhall West Midlands England WV13 3PW Model: Model: HSA3400 EF-KIT1 HSA3400 HSA3020 EF-KIT2 HSA3020 EF-DC HSA3060 HSA3060 EF-PIR HSA3010 HSA3010 EF-PETPIR HSA3050 EF-KF HSA3050 HSA3045 EF-KP HSA3045 HSA3080 EF-BX HSA3080 HSA3030 EF-SD HSA3030 HSA3070 EF-PB HSA3070 EF-PANEL EN 300 220-1 / V2.3.1 (2010) EN 300 220-2 / V2.3.1 (2010) EN 301 489 -1 / V1.8.1 (2008) EN 301 489-3 / V 1.4.
PAGE 30
Installation Notes: 30
PAGE 31
PAGE 32
All devices EMC Power supply 3 x AAA alkaline cells. 3 Passive infra red (PIR) detector years typical domestic service life All devices Passive infra red (PIR) detector 2 Year Guarantee Statement Alarm processing Microprocessor dual edge sequential pulse EMC controlled Tested to ETS 300 683 count with pulse length discrimination Radio Components tested to EN Tested to433.92MHz ETS 300 683 Radio AM transmitter 300 220-1 Radio Components EN Power supply 4.5V,tested 3 x AAtoalkaline cells.