Installation Sheet

ManualsBrandsYale ManualsHandlesetWando Interior Trim Lever for Single Cylinder Handlesets with Round Rose from the Edge Series

P/N - Rev AYE HLINSTL

Yale Edge Series

Handleset Lock

Installation Instructions

For use on doors 1-3/8" to 1-3/4" (35mm - 45mm)

Backset is distance from door edge to center of hole on door face.

Select Proper Backset

To adjust backset of latch

from 2-3/8" to 2-3/4"

To adjust backset of latch

from 2-3/4" to 2-3/8"

Push latch tail.

Pull latch tail.

Cylinder

Exterior Handle

Interior Knob

Upper Deadbolt Lower Latch

Upper

Strike Plate

Lower

Strike Plate

2x M5x70mm Machine Screw

M4x31.7mm Machine Screw2x

M4x20mm Machine Screw1x

M4x18mm Wood Screw8x

Thumbturn

Latch Tail

Notch

Latch Faceplate

Backset

2-3/8" or 2-3/4"

(60mm - 70mm)

To adjust backset of deadbolt from 2-3/8" to 2-3/4"

To adjust backset of deadbolt from 2-3/4" to 2-3/8"

Retract latchbolt. Hold latch tail and

rotate faceplate

clockwise.

Once notch is in

groove, push latch

faceplate towards

latch tail.

Rotate latch faceplate

counter clockwise and

check that notch is at

2-3/8" mark.

Retract latchbolt. Hold latch tail and

rotate faceplate

clockwise.

Once notch is in

groove, pull latch

faceplate away

from latch tail.

Rotate latch faceplate

counter clockwise and

check that notch is at

2-3/4" mark.

2-3/4" (70mm)

2-3/8" (60mm)

Latch Tail

Summary of content (4 pages)

PAGE 1
Yale Edge Series Handleset Lock Installation Instructions ® Cylinder Thumbturn Upper Deadbolt Lower Latch 2x M5x70mm Machine Screw 2x M4x31.7mm Machine Screw 1x M4x20mm Machine Screw Interior Knob Exterior Handle Upper Strike Plate 8x M4x18mm Wood Screw Lower Strike Plate Select Proper Backset For use on doors 1-3/8" to 1-3/4" (35mm - 45mm) Backset is distance from door edge to center of hole on door face.
PAGE 2
1 Mark Door 2" (51mm) Use template enclosed to mark installation holes on both sides of door. 5-1/2" (140mm) Make mark for 1" (25mm) holes on door edge. Note: Recommended height from floor 36"-38" (914mm - 965mm). 2 Drill Holes Drill 2-1/8" (54mm) holes about halfway through door face, then finish drilling from other side to prevent splintering. Drill 1" (25mm) holes in center of door edge through to 2-1/8" (54mm) holes for deadbolt and latch.
PAGE 3
4 Install Exterior Handle & Interior Knob M4x31.7mm Place exterior handle with stems and square spindle into latch as shown. Press tightly against door face. Square Spindle Interior Knob After exterior handle is in position, install interior knob and tighten screws. On knob side of door install screw through washer and into bottom hole and tighten firmly. 5 Stems M4x20mm Install Cylinder and Thumbturn If necessary, turn cylinder tailpiece to horizontal position.
PAGE 4
6 Mark Jamb Close door until latchbolt touches door jamb. Mark latch and deadbolt top and bottom edges as shown. Using strike plates as templates, center plates within the marks. Trace outlines, inner holes, and screw holes of strikes. Note: Make sure strikes are aligned vertically. Vertical Centerline of Jamb Make sure strikes are aligned on latchbolt and deadbolt. 7 Drill Holes and Install Strikes Drill 1" (25mm) deep holes in door jamb for bolts. Chisel outline of strike plates 1/16" (1.