Assure Lock 2 Touch Key-Free YRD450-F Download Yale Access App Create an account if you don’t already have one, and tap “Set Up a Device”. Note: If you have an account with the August App, use the same username and password for the Yale Access App. Install and Set Up Your Lock Follow the step-by-step Installation and Setup Guide in this manual, or refer to the app installation guide with helpful videos.
All key-free locks should only be installed on homes with more than one point of entry.
Contents 3 In the Box 4 Set Up HomeKit (Optional, iOS Only) 24 Door Checker 5 Set Up Fingerprints and Entry Codes 25 Marking Templates 7 Installation and Setup Guide 9 Remove Existing Deadbolt 10 Using Your Lock 26 Check Door Measurements 11 Connecting to Your Lock 27 Make or Adjust Holes 12 LED Alerts 28 Install Deadbolt Latch 13 Resetting Your Lock to Factory Defaults 29 Install Exterior Keypad 14 Features 30 Install Mounting Plate 15 App Settings 31 A
In the Box 4 Lock 1. Exterior Keypad Hardware 2 1 3 2. Interior Lock 4 3. Strike Plate UP 4. Adjustable Deadbolt 5. Manual 6. Reset Pin 5 6 7 7. Mounting Plate 8. AA Batteries 8 AA 9. Screws a. b. c. d. e. X4 Add-Ons 10 a. d. b. e. c. 11 X2 9 a. b. c. X4 Strike Plate and Deadbolt Screws Teal Screw Set B Black Screw Set C Silver Screw Set D Optional Security Strike Plate Screws 10. DoorSense a. b. c. d. e. X2 X2 X2 d. e.
1/8 3/8 5/8 1/4 7/8 1/8 3/4 3/8 1/2 0 5/8 1/4 7/8 1/8 3/4 1/2 5/8 7/8 1/8 3/4 3/8 1 1/8 3/8 5/8 1/4 7/8 4 5 F If printed from electronic file, Measure ruler to check scale. Set print scale to 1:1.
1/8 3/8 5/8 1/4 7/8 1/8 3/4 3/8 5/8 1/4 1/2 7/8 1/8 3/4 1/2 0 1 I 3/8 5/8 1/4 7/8 3/8 5/8 1/4 1/2 2 G 1/8 3/4 7/8 1/8 3/4 3/8 1/2 Less than G (Adjust diameter to G or H) Greater than H (Your door is not a match) 6 1/2 3 4 5 If printed from electronic file, Measure ruler to check scale. Set print scale to 1:1.
Marking Template for 2-1/8” (54mm) Face Bore C 1-3/4” (44.5mm) F Door Thickness 2-3/4” (70mm) 7 Center of Backset 2-1/8” (54mm) Face Bore Edge Bore I 2-1/8” Tear Along the Dotted Line Center of 1” (25mm) H Centerline Center of 1” (25mm) Edge Bore Center of B 1-3/8” (35mm) Door Thickness E 2-3/8” (60mm) 2-1/8” (54mm) Face Bore Backset If printed from electronic file, Measure ruler to check scale. Set print scale to 1:1.
Marking Template for 1-1/2” (38mm) Face Bore C 1-3/4” (44.5mm) F Door Thickness 8 2-3/4” (70mm) Backset Center of 1-1/2” (38mm) Center of Face Bore I 1-1/2” Edge Bore G Centerline Center of 1” (25mm) Center of Edge Bore 1-1/2” (38mm) Face Bore B 1-3/8” (35mm) Door Thickness E 2-3/8” (60mm) Backset If printed from electronic file, Measure ruler to check scale. Set print scale to 1:1.
Installation and Setup Guide Required Tools 1 You Might Also Need 3 9 1. Phillips Head Screwdriver 2. Door Checker 4 (tear off pages 5-6 of this manual) 3. Tape Measure 6 4. Drill 2 0 5 1 2 3 C B v A 4 5 5. Marking Template 7 (tear off pages 7-8 of this manual) 6. Pencil 6 E D Door Checker Part 1 8 9 7. Wood Mortise Chisel 8. Utility Knife 9.
1a 10 Remove Existing Deadbolt If you have a new door, please proceed to step 1b. If you have a deadbolt on your door, use the diagram to help you remove it. Frame Door Keep your old deadbolt until your new lock has been successfully installed.
1b 11 Check Door Measurements If your door doesn’t have holes, please proceed to step 1c. Tear off the Door Checker (pages 5-6) and follow the guidelines on both sides to If you need to make adjustments, go to measure each aspect of your door and frame. There are some cases when existing step 1c and find the closest match to each holes cannot be adjusted to be compatible. aspect of your door on the Marking Template.
1c 12 Make or Adjust Holes Skip this step if you have confirmed that the existing holes are compatible (step 1b). 1. Tear off the Marking Template (pages 7-8), and choose the 6. On the door frame, align the center of the strike plate with the preferred face bore diameter (2- 1/8” or 1-1/2”) on either side center of the edge bore. Trace the strike plate, then chisel to the of the template. depth of the strike plate so it sits flush with your door frame.
2 13 Install Deadbolt Latch 1. Correct deadbolt length is based on the backset. Refer to measurements Minimum strike pocket depth is 1”. E and F on the Door Checker (page 5) to verify backset. E 2-3/8” Backset (Out of box) 2-3/4 2-3/8 F 2-3/4” Backset (To adjust, twist neck by holding the body stable) UP 2-3/4 2-3/8 x 2 for Deadbolt Latch x 2 for Strike Plate (Actual size) UP 3 2. Align strike plate with deadbolt latch. 2a.
3 14 Install Exterior Keypad 1. Refer to measurements G and H on the Door Checker (page 6) to measure face bore hole. If the hole is less than 2-1/8” (H), remove adapter by 1 twisting it off the body of the lock. Note: Removing the adapter might also help if your face bore and edge bore are of irregular shape or are not properly aligned. Install your lock with the door open. Do not close your door until all the steps are completed. 2. Remove the plastic cover from the keypad. 3.
4 15 Install Mounting Plate 1. Refer to measurements B, C, and D on the Door Checker (page 5) to select screws. B C D x 2 Teal Screws (1-3/8” door thickness) x 2 Black Screws (1-3/8” - 1-3/4” door thickness) x 2 Silver Screws (1-3/4” - 2-1/4” door thickness) 2. Route the wire cable into the designated slot in the mounting plate. You may have to squeeze the cable slightly in order for it to pass through. 3. Guide posts of the mounting plate into the holes on the exterior keypad. 4.
5 16 Attach Wire Cable to Interior Lock 1. Remove battery cover by pulling it upwards off the body of the interior lock. 3 1 2 2. Make sure the side of the cable end with the ridges and the marked line faces outward. 3. Push cable into the designated slot until you hear a click.
6 17 Install Interior Lock 1. Make sure the tailpiece is in horizontal position. Use the thumbturn to adjust if needed. 2. Slide the tailpiece through the deadbolt latch slot. 3. Press the lock against the mounting plate, adjusting its position until it clicks into place and the bottom of the lock is held in place. 4. Tighten the one pre-installed screw. 2 4 1 3 When fully tightened, lock should be flush to door.
7 18 Test Thumbturn If deadbolt latch does not lock or unlock with the thumbturn (from the inside): • Ensure that the deadbolt latch is centered in the face bore hole; • Ensure that the tailpiece is positioned horizontally and inserted through deadbolt latch slot (step 6, point 2). Smooth deadbolt latch operation will enhance your battery life.
8 19 Install Yale Smart Module (Optional) If your lock model does not include a Smart Module, please proceed to step 9a. Insert Yale Smart Module into the designated slot at the top of the body of the lock. Note: If you purchased your module separately, check compatibility with your Assure 2 Touch. See table below for the list of compatible modules. AYR-MOD-ZWV-USA Z-Wave 500 series Module AYR-MOD-WF1-USA Wi-Fi Module Batteries must not be installed when inserting or removing Yale Smart Module.
9a 20 Install DoorSense (Optional) If you do not wish to install DoorSense, please proceed to step 10. DoorSense is a magnetic sensor installed on your door frame that can keep track of when the door is opened and closed. For surface mount instructions, please proceed to step 9b. For flush mount instructions, please proceed to step 9c. Surface mount is a quick and easy option to secure DoorSense on the inside of your door frame. Flush mount is installing DoorSense into the edge of the door frame.
9b 21 DoorSense Surface Mount 1. Remove one side of the backing from the adhesive. 1 4 1-1/2” 2. Attach tape to the back of the DoorSense, ensuring it is aligned with the 5 edges of the device and the screw holes. 3. Remove the remaining backing from the adhesive. 2 4. Determine mounting location. For optimal performance, DoorSense should be mounted within 1-1/2” from the edge of your door frame.
9c 22 DoorSense Flush Mount 1. Take off DoorSense cover. 1 2 2. Push the magnet out of the housing. 3. Expose the adhesive on the magnet cap by removing the blue backing. 4. Press the magnet onto the cap so that the notches interlock. 5. Determine mounting location on the door frame. The distance from the Frame 3 center of the strike plate to the center of the DoorSense should be 2”, 7 making the DoorSense in line with the logo on the battery cover of the lock. 5 6.
10 Install Batteries and Set Up with App 23 Make sure you have Yale Access App downloaded and an account created. Once batteries are inserted, lock is ready to be set up with the app. 3 2 1. Before installing batteries, make sure the deadbolt latch is unlocked. 2. Place ribbon behind batteries for easy battery removal. 3. Install 4 batteries. 1 4. Once batteries are inserted, the entire keypad will light up in a clockwise pattern. Once this happens, the lock is in pairing mode.
11 Set Up HomeKit (Optional, iOS Only) 24 If you do not wish to set up HomeKit, please replace battery cover and proceed to step 12. Enabling the HomeKit integration allows you to connect your lock and control it from your iPhone with the Apple Home app. 2 2. To begin setup, you’ll need access to the 8-digit HomeKit accessory code located on the side of the lock under the battery cover. Follow the instructions in the Yale Access app to set up HomeKit.
12 Set Up Fingerprints and Entry Codes You can register and manage fingerprints or entry codes from the Guest List tab of the Yale Access app. You must have Bluetooth connection with the lock to create or manage fingerprints. You must have Bluetooth or Wi-Fi connection with the lock to create or manage entry codes. 1. To create a credential for a new user, tap on “Invite”, then select whether they should also have app access or only fingerprint/entry code access.
Using Your Lock Exterior Keypad 26 Interior Lock 6 1 2 1. Exterior LED Indicator To lock your door 2. Wake / One-Touch Locking / Press Fingerprint Scanner 3. Warnings / Menu 4. Submit Entry Code To unlock your door 5. 9-Volt Battery Backup (See page 33 for instructions • With fingerprint* for if batteries are drained) Touch 6. Thumbturn 7. Passage Button • With entry code 3 4 5 8.
Connecting to Your Lock 27 There are two possible ways to connect to your lock with your Yale Access app. When you’re near your lock you can connect through Bluetooth, and if you have an optional module you can connect remotely through Wi-Fi.
LED Alerts 28 Exterior Keypad Alerts Interior Lock Alerts Gear flashes amber Low battery level 1 LED indicator flashes blue Low battery levels 1, 2, and 3 Gear flashes red Low battery level 2 LED indicator flashes red Locked state Gear flashes red, then stays red Low battery level 3 LED indicator flashes green Unlocked state Checkmark flashes Pairing success Pairing success Any key, then gear flash red Jammed lock LED indicator turns green for 3 seconds Gear flashes white Pairing LED
Resetting Your Lock to Factory Defaults If you have set up your lock with Yale Access App, you should reset it using the app. Go to your lock’s settings and choose “Factory Reset”. 1. Remove one battery. 2. Insert reset pin into the designated reset hole. 3. Press and hold the reset pin. 4. While holding the reset pin, reinsert battery. 5. Keep holding the reset pin for 5 more seconds. 6. Take out the reset pin.
Features 30 DoorSense · DoorSense keeps track of when your door is closed or open. Fingerprint · Unlock your door by scanning your fingerprint. Entry Codes · · · · Entry codes are used to unlock your door. Create entry codes from the “Guest List” tab in the Yale Access App. You can set permanent, recurring, and temporary entry codes. An unlimited number of entry codes can be created or deleted as long as you have Bluetooth or Wi-Fi connection to the lock.
App Settings 31 You can find these and other settings in the Yale Access App. Security Hide Entry Codes If turned on, all entry codes within the app will be hidden from view. Verified Access If turned on, biometric/passcode authentication is required to operate the lock using the app. Notifications Smart Alerts Create alerts you wish to receive from the app. Automation Auto-Lock Door will automatically lock, either when door is closed (with DoorSense), or on a timer.
App Settings 32 You can find these and other settings in the Yale Access App. Advanced Device Settings Device Settings Volume You can turn the lock volume on or off, and set it to high or low. Inside Indicator Light When turned on, it will show the active status (e.g. locked) of the lock. This light will also inform you when the batteries are low, passage mode is enabled, and pairing is successful. One-Touch Locking Lock the keypad by touching the Yale logo.
Lock Operations Troubleshooting 33 Lock does not respond. · · · · · Lock is on for a while then shows no reaction. Lights dim. · Batteries do not have enough power. Replace batteries*. Lock chimes indicating code acceptance but door will not open. · Check for any foreign objects between door and frame. · Check that the wire is firmly connected to the interior lock. Lock operates to allow access but will not automatically unlock. · Check to see if Auto-Lock is enabled.
Lock Operations Troubleshooting Lock does not unlock with fingerprint. Entry code will not register. 34 · Verify that you’re using a registered finger. · Make sure the finger you’re using is clean and dry. · · · · If low battery indicator is lit, replace batteries*. Verify that your entry code consists of 4 to 8 digits. Make sure you are using different entry codes for different users.
Hardware Troubleshooting 35 Deadbolt grinds and will not extend to lock when using an entry code but thumbturn locks and unlocks smoothly. · Lock was not handed properly. Find the setting called “Lock Handing” to fix this issue. Deadbolt is hitting the strike plate. · Reposition the strike plate to align with deadbolt. Deadbolt is not fully extending. · Increase depth of the deadbolt strike pocket in the frame. Adjust your existing knob, lever, or handleset strike plate.
Use: FCC: Warning: Use of the Works with Apple badge means that an accessory has FCC ID: 2ABFG-YRD450-F Changes or modifications to this device, not expressly approved by been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple Yale Home could void the user’s authority to operate the equipment. IC ID: 11626A-YRD450-F performance standards.
