User Manual

Effect Par ameter List
258 Appendix • A5000/A4000                                                               
Effect Par ameter List
This section explains the meaning of each parameter in each effect.
The tables give the parameter number, the range of settings (or selections), and the explanation.
(“@” marked parameters have no effect even if a program controller is assigned to the function)
1: DIGITAL SCRATCH
1 Input Level 0 — 127 Scratch depth
2 Initial Delay 0.1 — 460.0ms Delay time
3 Scratch Speed 1 — 127 Scratch modulation frequency
4 Scratch Depth 0 — 127 Scratch modulation depth
5 Auto Pan Speed 0.00Hz — 39.7Hz Autopan frequency
6 Auto Pan Depth 0 — 127 Autopan depth
7 EQ Frequency 100Hz — 10.0kHz Frequency at which the EQ will boost/cut the mid range
8 EQ Gain -12 — +12dB Gain by which the EQ will boost/cut the mid range
9 EQ Width 1.0 — 12.0 Width of the mid range area boosted/cut by the EQ
10 HPF Frequency thru, 20Hz — 8.0kHz Frequency at which the high pass filter will cut the low range
11 Dry/Wet Balance D63>W — D=W — D<W63 Balance between dry sound and effect sound
2: AUTO SYNTH
1 Mod Speed 0 — 127 Modulation speed
2 Mod Wave Type TypeA,TypeB,TypeC,TypeD Modulation type
3 Mod Depth 0 — 127 Modulation depth
4 Mod Depth Ofst R -64 — +63 R ch offset relative to modulation depth
5 LPF Frequency 1.0kHz — 18.0kHz,thru Frequency at which the low pass filter will cut the high range
6 HPF Frequency thru,22Hz — 8.0kHz Frequency at which the high pass filter will cut the low range
7 Dry Mix Level 0 — 127 Add dry sound before the delay input
8 Delay Time 0.1 — 370.0ms Delay time
9 Delay Time Ofst R 0 — -884 Delay time offset for the R ch offset
10 Feedback Level -63 — +63 Feedback amount
11 FB Level Ofst R -63 — +63 Feedback offset for the R ch
12 Delay Level 0 — 127 Delay level
13 AM Speed 0 — 127 Modulation frequency
14 AM Wave tri,sine,saw up,saw down Select modulation waveform
15 AM Depth 0 — 127 Amplitude modulation depth
16 AM Inverse R normal,inverse Left/right phase reversal of the amplitude modulation signal
3: TECH MODULATION
1 Mod Speed 0 — 127 Modulation speed
2 Mod Depth 0 — 127 Modulation depth
3 Pre Mod HPF Freq thru, 20Hz — 8.0kHz Frequency at which the high pass filter will cut the low range
4 Mod Gain -12 — +12dB Gain of the modulation signal
5 Mod LPF Frequency 1.0kHz — 18.0kHz, thru Frequency at which the low pass filter will cut the high range
6 Mod LPF Resonance 1.0 — 12.0 Resonance of the low pass filter
7 Mod Mix Balance D63>W — D=W — D<W63 Balance between the effect sound and the dry sound before the delay input
8 Delay Time 0.1 — 740.0ms Delay time
9 Delay Time Ofst R 0 — -884 Delay time offset for the R ch
10 Feedback Level -64 — +63 Feedback amount
11 FB Level Ofst R -64 — +63 Feedback offset for the R ch
12 Feedback High Damp 0.1 — 1.0 Adjust the high range attenuation (lower values will cause the high range to decay faster)
13 FB Hi Damp Ofst R -0.9 — +0.9 High Damp offset for the R ch
14 Dry/Wet Balance D63>W — D=W — D<W63 Balance between the dry sound and effect sound
4: NOISY MOD DELAY
1 Dry/Wet Balance D63>W — D=W — D<W63 Balance between the dry sound and the effect sound
2 Mod Speed 0 — 127 Delay modulation frequency
3 Mod Wave Type Type-A, Type-B, Type-C, Type-D Modulation type
4 Mod Depth 0 — 127 Modulation depth
5 Delay Time 0.1ms — 650.0ms Delay time
6 Feedback Level -63 — +63 Feedback amount
7 Mod Mix Balance 1 — 127 Balance between delay sound and delay bypass sound
8 EQ High Gain -12dB — +12dB Gain by which the EQ will boost/cut the high range
9 HPF Frequency thru, 20Hz — 8.0kHz Frequency at which the high pass filter will cut the low range
5: NOISE AMBIENT
1 Dry/Wet Balance D63>W — D=W — D<W63 Balance between dry sound and effect sound
2 Mod Speed 0 — 127 Modulation speed
3 Mod Depth 0 — 127 Modulation depth
4 Noise Level 0 — 127 Level of noise component
5 LPF Frequency 1.0kHz — 18.0kHz,thru Frequency at which the low pass filter will cut the high range
6 Dry Mix Level 0 — 127 Pre-delay dry level
7 Delay Time 0.1 — 370.0ms Delay time
8 Delay Time Ofst R 0 — -884 Delay time offset for the R ch
9 Feedback Level -63 — +63 Feedback amount
10 Dry Level 0 — 127 Delay level
11 AM Speed 0.0Hz — 39.70Hz Modulation frequency
12 AM Wave tri,sine,saw up,saw down Modulation waveform selection
13 AM Depth 0 — 127 Depth of amplitude modulation
14 AM Inverse R normal,inverse Invert left/right phase of amplitude modulation signal