User Manual

Effect Par ameter List
260 Appendix • A5000/A4000                                                               
13: RADIO
1 Noise Level 0 — 127 Degree of noise modulation
2 Tone 0 — 127 Tone of noise modulation
3 Mod LPF Frequency 1.0kHz — 18.0kHz, thru Frequency at which the low pass filter will cut the high range
4 Mod LPF Resonance 1.0 — 12.0 Resonance of low pass filter
5 HPF Frequency thru,22Hz — 8.0kHz Frequency at which the high pass filter will cut the low range
6 LPF Frequency 1.0kHz — 18.0kHz, thru Frequency at which the low pass filter will cut the high range
7 Dry/Wet Balance D63>W — D=W — D<W63 Balance between dry sound and effect sound
14: DIGITAL TURNTABLE
1 Click Density 0 — 5 Frequency with which the click sounds will occur
2 Click Level 0 — 127 Level of the click sounds
@3 Noise Tone 0 — 6 Tone of noise
4 Noise Mod Speed 0.00Hz — 39.7Hz Amplitude modulation frequency of the noise
5 Noise Mod Depth 0 — 127 Amplitude modulation depth of the noise
6 Dry Send to Noise 0 — 127 Mixture of dry signal into the noise
7 Noise LPF Freq 1.0kHz — 18.0kHz, thru Frequency at which the low pass filter will cut the high range
8 Noise LPF Q 1.0 — 12.0 Low pass filter resonance
9 Noise Level 0 — 127 Noise level
10 Dry LPF Frequency 1.0kHz — 18.0kHz, thru Frequency at which the low pass filter will cut the high range
11 Dry Level 0 — 127 Level of the dry sound
15: LOFI
1 SamplingFreq Ctrl 44.1kHz — 344Hz Selects the sampling frequency
2 Word Length 1 — 127 Sets the sound’s “roughness”
3 Output Gain -6dB — +36dB Output gain
@4 Filter Type thru,PowerBass,Radio,Telephone,Clean,Low Selects the type of sound
5 PreLPF CutoffFreq 63Hz — 18.0kHz, thru Frequency at which the low pass filter will cut the high range
6 PreLPF Resonance 1 — 12.0 Adds character to the input low-pass filter
7 Emphasis off/on Changes the high-frequency characteristics
8 Bit Assign 0 — 6 Adjusts the effect of the Word Length
9 Input Mode mono/stereo Mono/stereo input mode selection
10 Dry/Wet Balance D63>W — D=W — D<W63 Balance between dry sound and effect sound
16: LOW PASS FILTER, 17: HIGH PASS FILTER
1 Cutoff Freq 32Hz — 18.0kHz Specifies the filter cutoff frequency
2 Q 0 — 113 Sets the Q
@3 Filter Type -48dB, -24dB Selects the filter type
4 Q Type x1, x2 Selects the Q type
5 Output Gain -12dB — +12dB Output level
Noise may be produced with some voices when the “1. Cutoff Freq” is varied rapidly.
18: BAND PASS FILTER
1 Cutoff Freq 32Hz — 18.0kHz Specifies the filter cutoff frequency
2 Band Width 1 — 32 Sets the filter bandwidth
3 Q 0 — 113 Sets the Q
4 Output Gain -12dB — +12dB Output level
Noise may be produced with some voices when the “1. Cutoff Freq” is varied rapidly.
19: AUTO WAH + DIST, 20: AUTO WAH + OVERDRIVE
1 LFO Frequency 0.0Hz — 39.70Hz Frequency at which the wah filter will be controlled
2 LFO Depth 0 — 127 Depth at which the wah filter will be controlled
3 Cutoff Freq Offset 0 — 127 Offset value for the wah filter control frequency
4 Resonance 1 — 12.0 Bandwidth of the wah filter
5 Drive 0 — 127 (Distortion) Degree of distortion
6 PostDrive EQ Low -12dB — +12dB (Distortion) Gain by which the EQ will boost/cut the low range
7 PostDrive EQ Mid -12dB — +12dB (Distortion) Gain by which the EQ will boost/cut the mid range
8 PostDrive LPF Freq 1.0kHz — 18.0kHz, thru (Distortion) Frequency at which the filter will cut the high range
9 Drive Output Level 0 — 127 (Distortion) Output level
10 EQ Low Frequency 32Hz — 2.0kHz Frequency at which the EQ will boost/cut the low range
11 EQ Low Gain -12dB — +12dB Amount of gain by which the EQ will boost/cut the low range
12 EQ High Frequency 500Hz — 16.0kHz Frequency at which the EQ will boost/cut the high range
13 EQ High Gain -12dB — +12dB Amount of gain by which the EQ will boost/cut the high range
14 Dry/Wet Balance D63>W — D=W — D<W63 Balance between the dry sound and effect sound
21: TOUCH WAH + DIST, 22: TOUCH WAH + OVERDRIVE
1 Sensitive 0 — 127 Sensitivity at which the wah filter will change in response to the input level
2 Cutoff Freq Offset 0 — 127 Offset value for the wah filter control frequency
3 Resonance 1 — 12.0 Bandwidth of the wah filter
4 Drive 0 — 127 (Distortion) Degree of distortion
5 PostDrive EQ Low -12dB — +12dB (Distortion) Gain by which the EQ will boost/cut the low range
6 PostDrive EQ Mid -12dB — +12dB (Distortion) Gain by which the EQ will boost/cut the mid range
7 PostDrive LPF Freq 1.0kHz — 18.0kHz, thru (Distortion) Frequency at which the filter will cut the high range
8 Drive Output Level 0 — 127 (Distortion) Output leve
9 EQ Low Frequency 32Hz — 2.0kHz Frequency at which the EQ will boost/cut the low range
10 EQ Low Gain -12dB — +12dB Amount of gain by which the EQ will boost/cut the low range
11 EQ High Frequency 500Hz — 16.0kHz Frequency at which the EQ will boost/cut the high range
12 EQ High Gain -12dB — +12dB Amount of gain by which the EQ will boost/cut the high range
13 Dry/Wet Balance D63>W — D=W — D<W63 Balance between the dry sound and effect sound