STAGEPAS 1K Owner’s Manual 1
ATTENTION RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the rear of the unit. ATTENTION : POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION, FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PA_en_11 1/2 PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe place for future reference. This device is designed for use at musical or other live events. Do not use for any purposes other than the one intended. Those who are unfamiliar with handling or those who can not handle according to this manual such as children, should be supervised by responsible persons to ensure safety. • Be sure to connect to an appropriate outlet with a protective grounding connection.
PA_en_11 2/2 • To ensure proper heat dissipation of the product, when installing it: - Do not cover it with any cloth. - Make sure the top surface faces up; do not install on its sides or upside down. - Do not use the product in a confined, poorly-ventilated location. Inadequate ventilation can result in overheating, possibly causing damage to the product(s), or even fire. Make sure that there is adequate space around the product: at least 30 cm above, 30 cm at the sides and 30 cm behind.
Table of Contents PRECAUTIONS ....................................... 4 Playing Bluetooth® Audio ...................15 NOTICE ................................................... 5 Registering (pairing) a Bluetooth® device ................................................. 15 Connecting a Bluetooth® device......... 15 Information ............................................. 5 Introduction ............................................ 7 Playing audio files stored in a Bluetooth® device....................
Introduction Introduction Thank you for purchasing the Yamaha STAGEPAS 1K portable PA System! The STAGEPAS 1K is an all-in-one portable PA system that is designed for use at musical or other live events. This owner’s manual is intended for sound crew at live performances or other events. It explains the steps required to set up the STAGEPAS 1K throughout installation and connection of the PA system. It also explains how to operate the STAGEPAS 1K for sound amplification.
Controls and Functions Controls and Functions Top panel Mixer section Line array speaker socket Handle 0 A B 1 2 C 3 E 4 F D 5 G 6 7 Mixer section 1 [PROTECT] LED Lights red when the protection circuit is activated. The protection circuit will be activated in the following cases, and the speaker output will be muted. • Amplifier overheat is detected • A current surge is detected • The power to the unit is turned on: The protection circuit will be activated for a few seconds to avoid noise.
Controls and Functions 8 [Hi-Z] switches (channel 2-3) This switch is used when connecting a device directly to the mixer without a DI (direct box)—for example, instruments with passive pickups, such as an acoustic-electric guitar or electric bass without a battery. This function is effective only for the phone jack input. 9 [BLUETOOTH PAIRING] switch/LED This switch turns the Bluetooth audio connection on or off. It is also used to pair (register) a Bluetooth device (page 15).
Controls and Functions Rear panel H L I M J K N N O H Mic/Line input jacks (channels 1-3) Connect microphones, guitars, electronic musical instruments or audio equipment. These are combo jacks that support both XLR and phone plugs. Channels 2 and 3 support Hi-Z. XLR 10 Phone STAGEPAS 1K Owner’s Manual P I [LINK] input jack This jack supports an XLR-type plug.
Controls and Functions J [REVERB FOOT SW] jack This connects to an unlatched-type footswitch, such as the Yamaha FC5. This can be useful for solo performers, since you can toggle the reverb on and off as needed with your foot. K [ST] input jacks These jacks support phone-type plugs. Connect line-level devices such as electronic musical instruments, acoustic-electric guitars, CD players, and portable audio players. For monaural input, connect a cable to the L/MONO jack.
Quick Start Guide Quick Start Guide Attaching the line array speaker and spacers Use the included spacers to install the line array speaker at approximately the same height as the ears of the audience. The line array speaker features a grille. Connecting microphones, musical instruments, or audio devices to the mixer Before making connections, lower the volume level to the minimum by rotating the [LEVEL] controls counterclockwise.
Quick Start Guide 4. Insert the other end of the power cord into a power outlet. 8. Turn on the power to the connected musical instrument or audio device, then to this unit. The [POWER] LED lights up. Warning • The STAGEPAS 1K has been designed for grounded use. To avoid electrical shock and damage to connected devices, be sure to ground the unit using the included power cord. If you have any questions regarding proper connections, please contact your nearest Yamaha dealer.
Combining Two STAGEPAS 1K Units Combining Two STAGEPAS 1K Units Playing sound in stereo Expanding the number of STAGEPAS 1K input channels You can use two STAGEPAS 1K units to play sound in stereo. You can double the number of input channels by connecting two STAGEPAS 1K to each other. Each STAGEPAS 1K will operate as monaural. 1. Connect the [LINK] output jack of the 1. Connect the [LINK] input jack and the [LINK] L-channel STAGEPAS 1K to the [LINK] input jack of the R-channel STAGEPAS 1K.
Playing Bluetooth® Audio Playing Bluetooth® Audio You can set up the STAGEPAS 1K so it will play audio files stored in Bluetooth devices, such as a mobile device. Connecting a Bluetooth® device 1. Press and hold down the [BLUETOOTH PAIRING] switch for one second. Registering (pairing) a device Bluetooth® Before you can connect a Bluetooth device for the first time, you need to “pair” the device. “Pairing” refers to registering one Bluetooth device with another Bluetooth device.
Controlling the unit from STAGEPAS Editor Controlling the unit from STAGEPAS Editor You can control the parameters and view the meters and clipping information of the STAGEPAS 1K from your Bluetooth device, such as a mobile device. Disconnecting STAGEPAS Editor To view information on how to use STAGEPAS Editor, tap the [User Guide] button on SETTINGS screen in STAGEPAS Editor. 1.
Initializing the STAGEPAS 1K Initializing the STAGEPAS 1K Storing the Unit 1. Install the included, dedicated cover over the If you want to reset the parameters that were programmed from STAGEPAS Editor, or reset the Bluetooth pairing (registering) information to the factory default settings, follow the steps below: STAGEPAS 1K. 1. Turn the power switch off. 2.
Troubleshooting Troubleshooting Power does not turn on. Did you firmly and securely connect the power cord? Power shuts down suddenly. Are the vents of the mixer blocked? Since inadequate ventilation can result in overheating the mixer, the power may be turned off automatically to protect the system from overheating. Arrange the ventilation for better cooling, then turn on the power again. No sound is heard.
Troubleshooting MEMO STAGEPAS 1K Owner’s Manual 19
General Specifications General Specifications Main specifications System Type Powered subwoofer with a line array speaker Frequency Response (–10 dB) 37 Hz - 20 kHz Coverage Angle (Horizontal x Vertical) 170° x 30° Crossover Frequency 240 Hz Maximum Output Level (Measured peak, IEC noise@1m) 119 dB SPL Power Requirements 110-120V 60Hz, 220-240V 50/60Hz Power Consumption 25W (idle), 85W (1/8 power) Dimensions (W x H x D) System (maximum) 334 x 2,000 x 418 mm Weight 23.
General Specifications Input Characteristics Input Level*1 Input Terminals Connector Type XLR CH IN1 XLR Combo Phone XLR CH IN2-3 XLR Combo Hi-Z SW MIC/LINE SW – MIC – LINE – MIC – LINE – MIC – LINE MIC OFF LINE Phone MIC ON ST IN Source Impedance 3 kΩ (Balance) 150Ω Mics/Lines 10 kΩ (Balance) 150Ω Mics/Lines 3 kΩ (Balance) 150Ω Mics/Lines 10 kΩ (Balance) 150Ω Mics/Lines 1 MΩ (Unbalance) 10 kΩ Lines Sensitivity*2 Nominal*3 Max.
General Specifications Dimensions Subwoofer 280 418 1051 550 1526 2000 334 Line array speaker 67 86 86 555 582 67 Spacer Unit: mm STAGEPAS 1K Owner’s Manual 53
54 LINK-IN STAGEPAS 1K Owner’s Manual R Rch Lch REVERB FOOT SW BA BA HA Dif HiZ Hi-Z HiZ Hi-Z MIC/LINE PHONE (Unbal) ● BLUETOOTH PAIRING Bluetooth AUDIO (ST) (Unbal) MINI ST PHONE (Unbal) L/MONO ST CH3 (MIC / LINE / Hi-Z) COMBO (Balance) CH2 (MIC / LINE / Hi-Z) COMBO (Balance) CH1 (MIC / LINE) COMBO (Balance) XLR (Balance) CH LEVEL (Panel) (ͤ1) CH LEVEL (Panel) (ͤ1) ST LEVEL (ͤ1) REVERB ON BA BA MIC/LINE HA MIC/LINE CH LEVEL (Panel) (ͤ1) ● CLIP HA ● CLIP ● CLIP AD
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
EN SIMPLIFIED EU DECLARATION OF CONFORMITY Hereby, Yamaha Music Europe GmbH declares that the radio equipment type STAGEPAS 1K is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://europe.yamaha.com/en/support/compliance/doc.
LT SUPAPRASTINTA ES ATITIKTIES DEKLARACIJA Aš, Yamaha Music Europe GmbH, patvirtinu, kad radijo įrenginių tipas STAGEPAS 1K atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: https://europe.yamaha.com/en/support/compliance/doc.html HU EGYSZERŰSÍTETT EU-MEGFELELŐSÉGI NYILATKOZAT Yamaha Music Europe GmbH igazolja, hogy a STAGEPAS 1K típusú rádióberendezés megfelel a 2014/53/EU irányelvnek.
Informations concernant la collecte et le traitement des déchets d’équipements électriques et électroniques Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.
Important Notice: Guarantee Information for customers in European Economic Area (EEA) and Switzerland English Important Notice: Guarantee Information for customers in EEA* and Switzerland For detailed guarantee information about this Yamaha product, and Pan-EEA* and Switzerland warranty service, please either visit the website address below (Printable file is available at our website) or contact the Yamaha representative office for your country.
ADDRESS LIST NETHERLANDS/BELGIUM/ LUXEMBOURG NORTH AMERICA CANADA Yamaha Music Europe Branch Benelux Clarissenhof 5b, 4133 AB Vianen, The Netherlands Tel: +31-347-358040 Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario, M1S 3R1, Canada Tel: +1-416-298-1311 FRANCE U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A. Tel: +1-714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México, S.A. de C.V. Av. Insurgentes Sur 1647 Piso 9, Col.
VCF2340 SPEAKER ACCESSORY DL-SP1K Owner’s Manual EN Bedienungsanleitung DE Mode d’emploi FR Manual de instrucciones ES Manual do Proprietário PT Manuale di istruzioni IT Руководство пользователя RU ֵ⭞䈪᱄Ҝ ZH ࡅۉ۳ֵۭ KO 取扱説明書 JA
Specifications / ࣙࢆ Casters / 㝐䖤 : ∅50 mm ×4 Buckles for the cover / ཌ㖟ᑜᢙ : Plastic buckles / ງᯏᑜᢙ ×4 Dimensions (W × H × D) / ተሮδᇳ h 儎 h ε : 390 × 135 × 475 mm Weight / 䠃䠅 : 2.
English PRECAUTIONS PA_en_11 PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe place for future reference. This product is a convenient dolly that is designed for use with the STAGEPAS 1K. Do not use for any purposes other than the one intended. Those who are unfamiliar with handling or those who can not handle according to this manual such as children, should be supervised by responsible persons to ensure safety.
ру ц 1 2
3 --------------------I I I I I I I I I I I I I \ ----------~'• \ I I I I I I I I I I - ' , ~ - ,' , ~ , ________ \ -\<8;1tj1ef ,.1..-------- ::..,_ \ / I \/I~ \ / I --------,, I \ I I ~,~/ ,:,@ / \ I \ I \ / I \ / I ,., I \ ~ .;. • --------------------;,--I \ I I -------------------- –2–
(A) (B)
LPA696 P.O.BOX1, Hamamatsu Japan http://www.yamahaproaudio.com/ *All specifications are subject to change without notice. *All trademark and registered trademarks are property of their respective owners.
STUNNINGLY SIMPLE. IMPRESSIVELY PROFESSIONAL. What is it that makes one portable PA system stand out amongst the rest? Sound quality and output power? Flexible yet simple operation? Portability? Definitely all of the above and MORE. With the new STAGEPAS 1K our primary focus was to design a complete sound system that delivers professional quality sound despite a very simple setup and operation process that allows users to focus on what matters most — their performance.
J-Curve Slim Line Array The high-frequency speaker array is comprised of 10 small-diameter 1.5" speakers. By adopting a J-curve array configuration, the high-frequency unit achieves vertical coverage of 30 ° across a span of 170 °. With such a long, 10-driver array design the STAGEPAS can deliver clear, high quality sound consistently over longer distances, projecting uniform, high-quality sound from the front to the rear of the audience.
Digital mixer with versatile input With outstanding flexibility for a PA system of this size, the 5-channel digital mixer features three channels of mono microphone/line inputs and stereo inputs, with two of the mono input channels equipped with Hi-Z connectivity for direct input of acoustic-electric guitars and other instruments.
Simple setup Simply affix the 2 spacers and speaker unit into the subwoofer and setup is essentially done, with no cables, speaker stand, or additional gear required beyond the main unit. All you need is in the package. Expandable STAGEPAS systems Linking two STAGEPAS 1K’s provides wider coverage area and higher output power for larger scale performances. Both stereo and mono playback are supported, and when set to mono, both STAGEAPAS 1K inputs can still be used (up to 6 mono inputs plus 2 stereo inputs).
Application Examples Mobile DJ Specifications Guitar and vocals Main Specifications System Type Powered subwoofer with a line array speaker Frequency Response (-10 dB) 37 Hz - 20 kHz Coverage Angle (Horizontal x Vertical) 170° x 30° Crossover Frequency 240 Hz Maximum Output Level (Measured peak,IEC noise@1m) Power Requirements 119 dB SPL Depending on area of purchase; 100V 50Hz/60Hz, 110V-120V 60Hz, 220-240V 50/60Hz Power Consumption 25 W (Idle), 85 W (1/8 power) Dimensions (W x H x D) System
