User Manual

仕様 55
01V96i―取扱説明書
仕様
仕様
一般仕様
シーンメモリー数
99
サンプリング周波数
内部クロック
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
外部クロック
USB audio Normal Rate 44.1 kHz ±0.1%
48 kHz ±0.1%
Double Rate 88.2 kHz ±0.1%
96 kHz ±0.1%
The others Normal rate: 44.1 kHz-10% to 48 kHz+6%
Double rate: 88.2 kHz-10% to 96 kHz+6%
シグナルディレイ
fs=48 kHz
Less than 1.6 ms CH INPUT to STEREO OUT
fs=96 kHz
Less than 0.8 ms CH INPUT to STEREO OUT
フェーダー
100 mm motorized  17
フェーダー解像度
+10 ~ –138, – dB input faders
0 ~ –138, – dB master faders, stereo fader
全高調波歪率
*1
(CH INPUT to STEREO OUT)
(Input Gain=Min.)
fs=48 kHz
Less than 0.05% 20 Hz ~ 20 kHz @ +14 dB into 600 Ω
Less than 0.01% 1 kHz @ +24 dB into 600 Ω
fs=96 kHz
Less than 0.05% 20 Hz ~ 40 kHz @ +14 dB into 600 Ω
Less than 0.01% 1 kHz @ +24 dB into 600 Ω
周波数範囲
(CH INPUT to STEREO OUT)
fs=48 kHz
20 Hz~20 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω
fs=96 kHz
20 Hz~40 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω
ダイナミックレンジ
(maximum level to noise level)
110 dB typ. DA Converter (STEREO OUT)
105 dB typ. AD+DA (to STEREO OUT) @ fs=48 kHz
105 dB typ. AD+DA (to STEREO OUT) @ fs=96 kHz
ハム＆ノイズ
*2
(20 Hz~20 kHz)
Rs=150 Ω
–128 dB Equivalent Input Noise
–86 dB residual output noise. STEREO OUT (STEREO OUT off)
Input Gain=Max.
Input Pad =0 dB
–86dB (90dB S/N) STEREO OUT
(STEREO fader at nominal level and all CH INPUT faders at minimum level)
Input Pad =0 dB
Input Sensitivity
=–60 dB
–64dB (68dB S/N) STEREO OUT
(STEREO fader at nominal level and one CH INPUT fader at nominal level)
最大電圧ゲイン
74 dB CH INPUT (CH1~12) to STEREO OUT/OMNI (BUS) OUT
40 dB CH INPUT (CH13~16) to STEREO OUT
74 dB CH INPUT (CH1~12) to OMNI (AUX) OUT (via pre input fader)
74 dB CH INPUT (CH1~12) to MONITOR OUT (via STEREO BUS)
クロストーク
(@ 1 kHz)
Input Gain=Min.
80 dB adjacent input channels (CH1~12)
80 dB adjacent input channels (CH13~16)
80 dB input to output
AD Input (1~12)
Phantom switch
+48 V DC (each 4ch)
Pad switch
0/20 dB attenuation
Gain control
44 dB (–60 ~ –16), detented
Peak indicator
LED (red) turns on when post HA level reaches 3 dB below clipping at dig-
ital domain
Signal indicator
LED (green) turns on when post HA level reaches 20 dB below nominal at
digital domain
AD converter
24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over-
sampling (fs=88.2, 96 kHz)