Digital Mixing Console Owner's Manual

ManualsBrandsYamaha ManualsMusical Instrument02R96

DIGITAL MIXING CONSOLE

Owner’s ManualOwner’s Manual

Owner’s Manual

Keep This Manual For Future Reference.

Summary of content (315 pages)

PAGE 1
DIGITAL MIXING CONSOLE Owner’s Manual Keep This Manual For Future Reference.
PAGE 2
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PAGE 3
i Important Information Warnings • • • • • • • • • • • • • • • Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Manual or as marked on the unit. Failure to do so is a fire and electrical shock hazard. Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock may result. Do not place heavy objects, including this unit, on top of the power cord. A damaged power cord is a fire and electrical shock hazard.
PAGE 4
ii • • • • • • • • This unit has ventilation holes along the front underside and at the rear to prevent the internal temperature from rising too high. Do not block them. Blocked ventilation holes are a fire hazard. In particular, do not operate the unit while it’s on its side, is upside down, or while it’s covered with a cloth or dust sheet. If you are using the optional MB02R96 Peak Meter Bridge, do not hold only the MB02R96 when moving the 02R96.
PAGE 5
iii 02R96 Exclusion of Certain Responsibility Manufacturer, importer, or dealer shall not be liable for any incidental damages including personal injury or any other damages caused by improper use or operation of the 02R96. Trademarks ADAT MultiChannel Optical Digital Interface is a trademark and ADAT and Alesis are registered trademarks of Alesis Corporation. Apogee is a trademark of Apogee Electronics, Inc.
PAGE 6
iv Stereo Out chapters contain cross-references to the relevant sections of the “Common Channel Functions” chapter. Conventions Used in this Manual The 02R96 features two types of button: physical buttons that you can press (e.g., ENTER and DISPLAY) and buttons that appear on the display pages. References to physical buttons are enclosed in square brackets, for example, “press the [ENTER] button.” References to display page buttons are not emphasized, for example, “press the ENTER button.
PAGE 7
v Contents 1 Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Control Surface & Rear Panel . . . . . . . . . . . . . . . . . 4 Control Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3 Operating Basics . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
vi 7 Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Patching Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Metering Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reversing the Signal Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gating Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 9
vii 9 Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Patching Bus Outs to Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Routing Input Channels to Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Metering Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monitoring Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 10
viii 11 Common Channel Functions . . . . . . . . . . . . . . . . . 87 Metering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Attenuating Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using EQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grouping Output Channel EQs . . . . . . . . . . . . . . . . . . . . . .
PAGE 11
ix 16 Automix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 About Automix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 What’s Recorded in an Automix? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Automix Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Channel Strip [AUTO] Buttons . . . . . . . . . . . . . . . . . . . . . .
PAGE 12
x 19 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 189 About the Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Assigning a Target to the Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the User Defined Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the User Defined Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 13
xi Appendix C: MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 Scene Memory to Program Change Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 Initial Parameter to Control Change Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Format Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 14
Welcome 1 1 Welcome Thank you for choosing the Yamaha 02R96 Digital Mixing Console. The 02R96 Digital Mixing Console offers 24-bit/96 kHz digital audio processing without compromise, comprehensive surround mixing and monitoring, including bass management, and hands-on control of popular DAW (Digital Audio Workstation) systems. Sonic Spec • • • • • Linear 24-bit, 128-times oversampling A/D converters Linear 24-bit, 128-times oversampling D/A converters 20 Hz–40 kHz (0.5, –1.
PAGE 15
2 Chapter 1—Welcome I/O Patching • • • • Any available input port can be patched to the Input Channels, Insert Ins, or Effects inputs Direct Outs, Insert Outs, Bus Outs, Aux Sends, and the Stereo Out can be patched to any output port Input and output ports can be named for easy identification Patches can be stored in the Input and Output Patch libraries EQ • • 4-band parametric EQ on all Input and Output Channels EQ library with 40 presets, 160 user memories Groups & Pairs • • • • • • Horizontal and
PAGE 16
Welcome 3 Surround Sound • • • • • • 3-1 and 5.
PAGE 17
02R96—Owner’s Manual EFFECTS/PLUG-INS (p. 9) FADER MODE (p. 7) ENCODER MODE (p. 6) AUX SELECT (p. 6) DISPLAY ACCESS (p. 7) AD Input Section (p.
PAGE 18
Control Surface 5 AD Input Section AD Input #1 is shown at the top; AD Inputs #17 and #18 below. + 48V 1 2 3 4 5 6 ON OFF PAD 26dB A +48V ON/OFF switches (AD 1–16) These switches turn on and off the +48 V phantom power feed to each INPUT A (XLR-type connector). Phantom power is typically used to power condenser-type microphones or direct boxes. See “Phantom Power (AD 1–16)” on page 39 for more information.
PAGE 19
6 Chapter 2—Control Surface & Rear Panel D SOLO buttons These buttons are used to solo Channels. The [SOLO] button indicators of channels that are soloed light up. See “Soloing Channels” on page 102 for more information. E ON buttons These buttons are used to mute Input and Output Channels. Their exact operation depends on the currently selected Layer. The [ON] button indicators of channels that are on light up.
PAGE 20
Control Surface 7 C AUX button This button is used to select the Aux Encoder mode. Its indicator lights up when this mode is selected. In this mode, the Encoders function as Aux Send level controls when an Input Channel Layer is selected. While the Master Layer is selected, Encoders 1–8 function as Input Channel 49–56 Aux Send controls, and Encoders 9–24 are inactive. See “Selecting Encoder Modes” on page 36. D ASSIGN 1 & 2 buttons These buttons are used to select the assignable Encoder modes.
PAGE 21
8 Chapter 2—Control Surface & Rear Panel D UTILITY button This button is used to select the following pages: Oscillator, Channel Status Monitor, and Battery Check. E REMOTE button This button is used to select the Remote page. See “About the Remote Layer” on page 189 for more information. F MIDI button This button is used to select the following pages: MIDI Setup, Program Change Assign Table, Control Change Assign Table, and Bulk Dump. See “MIDI” on page 163 for more information.
PAGE 22
Control Surface 9 EFFECTS/PLUG-INS 2 3 4 EFFECTS / PLUG INS 1 DISPLAY INTERNAL EFFECTS PLUG INS CHANNEL INSERTS 1 2 3 4 5 6 7 A EFFECTS/PLUG-INS DISPLAY button This button is used to select the following pages: Effects Edit, Effects Library, Plug-In Setup, and Plug-In Edit. See “Internal Effects & Plug-Ins” on page 131 for more information. B INTERNAL EFFECTS button This button is used to select the internal effects processors in conjunction with the EFFECTS/PLUG-INS [1–4] buttons.
PAGE 23
10 Chapter 2—Control Surface & Rear Panel Display Section 1 2 3 4 5 A Display This 320 x 240 dot display with fluorescent backlight displays pages, information on the currently selected Scene and channel, the sampling rate, and more. See “About the Display” on page 29 for more information. B Contrast control This control is used to adjust the contrast of the display. C F1–F4 buttons These buttons are used to select the pages whose tabs are currently visible.
PAGE 24
Control Surface 11 SELECTED CHANNEL Section SELECTED CHANNEL ROUTING DISPLAY ACCESS DISPLAY 1 2 3 4 5 6 7 8 STEREO DIRECT PHASE / INSERT DELAY PAN / SURROUND DISPLAY FOLLOW PAN L R L R ODD EVEN LINK GRAB EFFECT DYNAMICS DISPLAY GATE ON COMP ON GATE / COMP GATE THRESHOLD RANGE ATTACK DECAY HOLD COMP THRESHOLD RATIO ATTACK RELEASE GAIN EQUALIZER LOW LOW MID HIGH MID HIGH DISPLAY FREQUENCY Q FREQUENCY GAIN Q 125 EQ ON Q GAIN FREQUENCY GAIN 1.00 4.
PAGE 25
12 Chapter 2—Control Surface & Rear Panel DISPLAY ACCESS DISPLAY ACCESS PHASE / INSERT DELAY 1 2 A PHASE/INSERT button This button is used to select the Input Channel Phase and Insert pages. See “Reversing the Signal Phase” on page 59 and “Using Inserts” on page 95 for more information. B DELAY button This button is used to select the Delay pages. See “Delaying Channel Signals” on page 101 for more information.
PAGE 26
Control Surface 13 they’re set to control a Compressor. See “Gating Input Channels” on page 60 and “Compressing Channels” on page 97 for more information. PAN/SURROUND 8 PAN / SURROUND 1 DISPLAY L R L R ODD EVEN 2 3 LINK 4 GRAB EFFECT 5 67 A PAN/SURROUND DISPLAY button This button is used to select the Input Channel Pan pages, the Surround Mode page, and the Surround Edit pages. See “Panning Input Channels” on page 67 and “Using Surround Pan” on page 69.
PAGE 27
14 Chapter 2—Control Surface & Rear Panel G EFFECT button This button is used to select the Joystick for parameter control of the Reverb 5.1 effect. Its indicator lights up when Reverb 5.1 effect control is on, and the Joystick cannot be used for surround panning. See “REVERB 5.1” on page 245 for more information. H Joystick This control can be used for surround panning, normal panning, or parameter control of the Reverb 5.1 effect.
PAGE 28
Control Surface 15 LAYER LAYER 1 1 24 REMOTE 25 48 MASTER 2 3 A 1–24 & 25–48 buttons These buttons select the Input Channel Layers, which determine which Input Channels are controlled by the channel strips. The LAYER button indicator for the currently selected Layer lights up. See “Selecting Layers” on page 33 for more information. B REMOTE button This button selects the Remote Layer, which can be used to control external devices, including DAWs.
PAGE 29
16 Chapter 2—Control Surface & Rear Panel SCENE MEMORY SCENE MEMORY 1 DISPLAY 00 STORE RECALL 23 4 5 6 A SCENE MEMORY DISPLAY button This button is used to select the following pages: Scene Memory, Input Channel Fade Time, Output Fade Time, Recall Safe, and Scene Memory Sort. See “Scene Memories” on page 138 for more information. B Scene memory display This displays the number of the currently selected Scene memory. See “Scene Memories” on page 138 for more information.
PAGE 30
Control Surface 17 MACHINE CONTROL 1 2 3 MACHINE CONTROL LOCATE MEMORY DISPLAY SET 1 2 3 4 5 6 7 8 4 5 REW FF STOP PLAY REC 6 7 8 A MACHINE CONTROL DISPLAY button This button is used to select the Locate Memory and Machine Configuration pages. See “Setting the Locate Memories” on page 194 and “Configuring Machines” on page 192 respectively for more information.
PAGE 31
18 Chapter 2—Control Surface & Rear Panel Data Entry & Transport 5 DEC 1 SHUTTLE INC 6 2 SCRUB 3 4 ENTER A SHUTTLE button This button is used to set the Parameter wheel to Shuttle mode for machine control (DAW, MMC). Its indicator lights up when Shuttle mode is on. See “Using Shuttle & Scrub” on page 193 for more information. B SCRUB button This button is used to set the Parameter wheel to Scrub mode for machine control (DAW, MMC). Its indicator lights up when Scrub mode is on.
PAGE 32
Control Surface 19 Monitor, Phones & Talkback Section 5 0 10 TALKBACK LEVEL 4 3 PHONES 0 10 0 10 STUDIO LEVEL PHONES LEVEL 1 2 A STUDIO LEVEL control This control is used to set the level of the STUDIO MONITOR OUT. See “Studio Monitoring” on page 115 for more information. B PHONES LEVEL control This control is used to set the level of the PHONES. See “Control Room Monitoring” on page 114 for more information.
PAGE 33
20 Chapter 2—Control Surface & Rear Panel MONITOR Section MONITOR The various subsections of the MONITOR section are explained below.
PAGE 34
Control Surface 21 CONTROL ROOM CONTROL ROOM 1 2 3 7 2TR D1 2TR A1 2TR D2 2TR A2 2TR D3 STEREO 4 5 6 8 ASSIGN2 ASSIGN1 SURROUND 9 BUS SLOT J K L 0 10 CONTROL ROOM LEVEL N DIMMER TALKBACK B STEREO 2TR D2 button This button selects the 2TR IN DIGITAL COAXIAL 2 as the Control Room Monitor signal source. Its indicator lights up when this source is selected. See “Control Room Monitoring” on page 114 for more information.
PAGE 35
22 Chapter 2—Control Surface & Rear Panel M DIMMER button This button is used to dim the Control Room Monitor and Surround Monitor signals. Its indicator lights up when these signals are dimmed. See “Control Room Monitoring” on page 114 for more information. N TALKBACK button This button turns on the Talkback function, which distributes the Talkback mic signal to the Studio Monitor Outs and any Slot or Omni Outputs specified on the Talkback Setup page.
PAGE 36
Power Section (p. 28) Analog Master I/O Section (p. 24) OMNI OUTs, Digital I/O & Control Section (p. 26) AD Input Section (p. 24) SLOT Section (p.
PAGE 37
24 Chapter 2—Control Surface & Rear Panel AD Input Section AD Input #1 is shown at the top; AD Inputs #17 and #18 below 1 2 A INPUT A & B (BAL) connectors AD Inputs 1 through 16 feature balanced XLR-3-31-type connectors and balanced 1/4-inch phone jacks, both with a nominal input range of –60 dB to +10 dB. Phantom powering (+48 V) is supplied to the XLR-type connectors, with individual ON/OFF switches on each input.
PAGE 38
25 Rear Panel level is controlled by the STUDIO LEVEL control. See “Studio Monitoring” on page 115 for more information. B STEREO OUT +4 dB (BAL) These balanced XLR-3-32-type connectors, nominal Female XLR plug output level +4 dB, output the analog Stereo Out signal and are typically connected the stereo inputs of a 2-track recorder. They are wired pin 1–ground, pin 2–hot (+), and pin 3–cold (–). See “Stereo Out Connectors” on page 73.
PAGE 39
26 Chapter 2—Control Surface & Rear Panel OMNI OUTs, Digital I/O & Control Section 2 3 4 56 7 8 9 J K L 1 M N O P A OMNI OUT +4dB (BAL) These balanced 1/4-inch TRS phone jacks, nominal output level +4 dB, provide eight analog outputs that can be patched to the following: Bus Outs, Aux Sends, the Stereo Out, Insert Outs, Direct Outs, or Surround Monitor Channels. See “Omni Outs” on page 40.
PAGE 40
Rear Panel 27 H 2TR IN DIGITAL COAXIAL 2 & 3 These phono connectors accept consumer format (IEC-60958) digital audio, and are typically used to connect the digital stereo outputs of 2-track recorders. Signals connected here can be monitored via the CONTROL ROOM MONITOR OUT by pressing the CONTROL ROOM [2TR D2] or [2TR D3] button. In addition, these inputs can be patched to Input Channels or Insert Ins. Unsynchronized digital audio signals can be converted by the internal sampling rate converters.
PAGE 41
28 Chapter 2—Control Surface & Rear Panel Power Section 1 4 2 3 A POWER ON/OFF switch This switch is used to turn on the power to the 02R96. See “Turning On & Off the 02R96” on page 29 for more information. B Grounding screw For electrical safety reasons, and correct operation of the touch-sensitive faders, it’s important that the 02R96 is grounded properly.
PAGE 42
Operating Basics 29 3 Operating Basics Connecting the Power Cord Warning: Turn off all equipment connected to the 02R96 before making any power connections. Connect the socket-end of the supplied power cord to the AC IN on the rear panel of the 02R96. Connect the plug-end to a suitable AC wall outlet, one that conforms to the power supply requirements stated on the 02R96’s rear panel.
PAGE 43
30 Chapter 3—Operating Basics EDIT indicator: This indicator appears when the current mix settings no longer match those of the Scene that was recalled last. It works in unison with the Edit indicator dot on the SCENE MEMORY display. See “Edit Buffer & Edit Indicator” on page 138 for more information. Selected DISPLAY: This indicates the currently selected display page group, for example, AUX, EQ, or AUTOMIX. Display page groups are selected by using the [DISPLAY] buttons.
PAGE 44
Selecting Display Pages 31 Selecting Display Pages • • • • Display pages are grouped by function, and each group of pages can be selected by using the following [DISPLAY] buttons: AUX SELECT, ENCODER MODE, DISPLAY EFFECTS/PLUG-INS, ROUTING, DYNAMICS, PAN/SURROUND, EQUALIZER, SCENE MEMORY, USER DEFINED KEYS, MACHINE CONTROL, MONITOR. Further page groups can be selected by using the DISPLAY ACCESS buttons. The next page in the group can be selected by pressing the [DISPLAY] button.
PAGE 45
32 Chapter 3—Operating Basics Confirmation Messages For certain functions, the 02R96 prompts you for confirmation before executing them, as shown here. Press YES to execute the function, or press NO to cancel. If no action is taken for awhile, the confirmation window closes automatically and the function is not executed. Title Edit Window The Title Edit window is used to enter titles for Scene and library memories, automixes, and so on.
PAGE 46
Selecting Layers 33 Selecting Layers Input and Output Channels are arranged into Layers, as illustrated below. There are four Layers altogether: two Input Channel Layers, a Master Layer (or Output Layer), and a Remote Layer.
PAGE 47
34 Chapter 3—Operating Basics Selecting Channels 1 2 To select Input and Output Channels for editing with the SELECTED CHANNEL controls, you use the LAYER buttons to select a Layer, and the [SEL] buttons to select a channel on that Layer. Select a Layer, as explained on page 33. Use the [SEL] buttons to select an Input or Output Channel. The [SEL] button indicator for the currently selected channel lights up.
PAGE 48
Selecting Fader Modes 35 Selecting Fader Modes 1 The exact function of each fader depends on the selected Layer and Fader mode. Select a Layer, as explained on page 33. 2 Use the FADER MODE buttons to select a Fader mode. FADER MODE FADER AUX [FADER]: Channel faders control Input Channel levels or Output Channel master levels, depending on the selected Layer. [AUX]: Channel faders control Aux Send levels, depending on the selected Layer.
PAGE 49
36 Chapter 3—Operating Basics Selecting Encoder Modes 1 The exact function of each Encoder depends on the selected Layer and Encoder mode. There are two preset Encoder modes, Pan and Aux, and two assignable modes, for which you can choose from over 40 parameters. Select a Layer, as explained in page 33. 2 Use the ENCODER MODE buttons to select an Encoder mode. ENCODER MODE DISPLAY PAN AUX ASSIGN 1 ASSIGN 2 [PAN]: Encoders function as Pan controls.
PAGE 50
Assigning Parameters to the ENCODER MODE Assign Buttons 37 Assigning Parameters to the ENCODER MODE Assign Buttons 1 Up to two parameters can be assigned to the two ENCODER MODE ASSIGN buttons. Initially, the following parameters are assigned to the ASSIGN buttons: [ASSIGN 1]: Input Patch [ASSIGN 2]: Direct Out Use the ENCODER MODE [DISPLAY] button to select the Encoder Mode Assign page. The names of the parameters currently assigned to each ASSIGN button are displayed in the left-hand box.
PAGE 51
38 Chapter 3—Operating Basics Assignable Encoder Mode Parameter List 02R96—Owner’s Manual # Parameter 1 No Assign Encoder Operation 2 Attenuator 3 Input Patch Input Channel patch Confirm patch selection 4 Insert In Patch Insert In patch Confirm patch selection 5 Insert Out Patch Insert Out patch Confirm patch selection 6 Direct Out Direct Out patch Confirm patch selection 7 Phase Phase: normal/reverse — — Attenuator Push Switch Operation — — 8 Insert On Insert on/off — 9
PAGE 52
Analog I/O & the AD Input Section 39 4 Analog I/O & the AD Input Section AD Input Section The 02R96 features 24 AD Inputs for connecting microphone and line-level sources. AD Inputs can be patched to Input Channels or Input Channel Insert Ins (see page 52). They can also be patched to Output Channel Insert Ins (see page 55). AD Input Connectors (AD 1–16) AD Inputs 1 through 16 feature balanced XLR-3-31-type connectors and balanced 1/4-inch phone jacks, both with a nominal input range of –60 dB to +10 dB.
PAGE 53
40 Chapter 4—Analog I/O & the AD Input Section AD Inserts (AD 1–16) AD Inputs 1 through 16 feature switchable analog inserts on 1/4-inch TRS phone jacks for the send and return signals. They are wired: sleeve–ground, ring–return, tip–send. The nominal signal level is +4 dB. OFF ON INSERT AD Input inserts can be turned on and off individually by using the INSERT ON/OFF switches, so you don’t have to disconnect your external equipment in order to remove an insert.
PAGE 54
Digital I/O & Cascading 41 5 Digital I/O & Cascading Wordclocks Unlike analog audio equipment, digital audio equipment must be synchronized when digital audio signals are transferred from one device to another, otherwise, signals may not be received correctly and audible noise, glitches, or clicks may occur. Synchronization is achieved using what’s called a wordclock, which is a clock signal for synchronizing all the digital audio signals in a system.
PAGE 55
42 Chapter 5—Digital I/O & Cascading Selecting the Wordclock Source The wordclock source can be selected as follows. Note: When you change the wordclock settings on any device in your digital audio system, some devices may output noise, so turn down your power amps beforehand, otherwise your speakers may be damaged. 1 Use the DISPLAY ACCESS [DIO] button to locate the Word Clock Select page. 2 Use the cursor buttons to select the sources, and press [ENTER] to set.
PAGE 56
2TR Digital Outs 43 Terminating External Wordclocks Wordclock signals distributed via BNC cables must be terminated correctly, otherwise, jitter and synchronization errors may result. Ideally, you should make a separate wordclock connection to each device and terminate it. The following examples show two ways in which wordclock signals can be distributed and how termination should be applied in each case. Normally the WORD CLOCK 75Ω ON/OFF switch should be set to ON.
PAGE 57
44 Chapter 5—Digital I/O & Cascading 2TR Digital Ins The 02R96 features three sets of 2-track digital inputs: 2TR IN DIGITAL AES/EBU 1 uses an XLR-3-31-type connector and accepts AES/EBU format digital audio. 2TR IN DIGITAL COAXIAL 2 and 3 use phono connectors and accept consumer format (IEC-60958) digital audio. These inputs can be monitored via the Control Room monitors by using the CONTROL ROOM [2TR D1], [2TR D2], and [2TR D3] buttons.
PAGE 58
Slot I/O 45 Slot I/O The 02R96 features four Slots for installing optional mini-YGDAI (Yamaha General Digital Audio Interface) I/O Cards, which offer various analog I/O options and digital I/O interfaces in all the popular digital audio interconnect formats, including AES/EBU, ADAT, and Tascam. Slot Inputs can be assigned to Input Channels or Input Channel Insert Ins (see page 52), or to Output Channel Insert Ins (see page 55).
PAGE 59
46 Chapter 5—Digital I/O & Cascading Installing I/O Cards 1 This section explains how to install I/O Cards. Turn off the 02R96. 2 Undo the two fixing screws and remove the slot cover, as shown below. Keep the cover and fixing screws in a safe place for future use. 3 Insert the card between the guide rails and slide it all the way into the slot, as shown below. You may have to push firmly to plug the card into the internal connector. 4 Secure the card using the attached thumbscrews.
PAGE 60
Slot I/O 47 Setting the Transfer Format for Higher Sampling Rates 1 2 The data transfer format for the higher sampling rates can be set as follows. Use the DISPLAY ACCESS [DIO] button to locate the Higher Sample Rate Data Transfer Format page. Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, or [ENTER] button to set them. The SLOT TYPE column displays the names of any installed I/O Cards.
PAGE 61
48 Chapter 5—Digital I/O & Cascading Dithering Digital Outputs 1 2 For digital audio transfer to lower-resolution systems, the 2TR Digital Outputs and Slot Outputs can be dithered to 16-bit, 20-bit, or 24-bit. Use the DISPLAY ACCESS [DIO] button to locate the Dither page. Use the cursor buttons to select the Dither parameters, and use the Parameter wheel or INC/DEC buttons to set them. The SLOT column displays the names of any installed I/O Cards.
PAGE 62
Cascading Consoles 49 Cascading Consoles Up to four 02R96s can be cascaded, offering a maximum of 224 Input Channels. Several functions are linked between all cascaded consoles, including Solo, Scene Recall and Store, so that all consoles work just like one big console. A single Yamaha 02R Digital Recording Console can be included in the cascade system. The CASCADE IN and CASCADE OUT ports are used to transmit and receive Cascade and control signals.
PAGE 63
50 Chapter 5—Digital I/O & Cascading Cascade Hookup Examples Cascading Two 02R96s Master: Off Bi-directional: - Master: On Bi-directional: On CASCADE OUT CASCADE IN 02R96 #1 02R96 #2 CASCADE IN CASCADE OUT Final signals can be output by the Slot Outputs or Omni Outs. Final signals can be output by the Slot Outputs or Omni Outs.
PAGE 64
Cascading Consoles 51 Attenuating Cascade Inputs 1 2 Cascade Inputs can be attenuated, and the Cascade mode and Cascade source can be specified on the Cascade In page. Use the DISPLAY ACCESS [DIO] button to locate the Cascade In page. Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, or [ENTER] button to set them. CASCADE MODE: When you want to output the same signals from two 02R96s, turn on the BI-DIRECTIONAL button.
PAGE 65
52 Chapter 6—Input & Output Patching 6 Input & Output Patching Input Patching Signal sources for the Input Channels, Input Channel Insert Ins, and internal effects processors are selected on the Input Patch pages, which are selected by using the DISPLAY ACCESS [INPUT PATCH] button. Use the cursor buttons to select the patch parameters, use the Parameter wheel or INC/DEC buttons to select a source, and press [ENTER] to set. Patch parameters display Short Port names.
PAGE 66
Input Patching 53 Patching Input Channel Insert Ins AD Inputs, Slot Inputs, internal effects processor outputs, Digital or Analog 2TR Inputs can be patched to the Input Channel Insert Ins. The Input Channel Insert In Patch parameters for the 56 Input Channels are divided between two pages. The Input Channel 1–48 Insert In Patch page is shown below. The layout of the other page is the same.
PAGE 67
54 Chapter 6—Input & Output Patching Output Patching Signal sources for the Slot Outputs, Omni Outs, Output Channel Inserts Ins, Direct Outs, and 2TR Digital Outputs are selected on the Output Patch pages, which are selected by using the DISPLAY ACCESS [OUTPUT PATCH] button. Use the cursor buttons to select the patch parameters, use the Parameter wheel or INC/DEC buttons to select a source, and press [ENTER] to set.
PAGE 68
Output Patching 55 Patching Omni Outs Bus Outs, Aux Sends, the Stereo Out, Input or Output Channel Insert Outs, or Surround Monitor Channels can be patched to the Omni Outs. Omni Outs can be patched to Direct Outs on the Direct Out Destination pages (see page 56). When an Omni Out is patched to a Direct out (see page 56), and that Direct Out is assigned on an Input Channel Routing page, the Omni Out patch cannot be changed here.
PAGE 69
56 Chapter 6—Input & Output Patching Patching Direct Outs Direct Outs can be patched to the Slot Outputs, Omni Outs, or 2TR Digital Outputs. The Direct Out Destination parameters for the 56 Input Channels are divided between two pages. The Input Channel 1–48 Direct Out Destination page is shown below. The layout of the other page is the same. In addition to using the cursor buttons, Patch parameters can also be selected by using the LAYER and [SEL] buttons.
PAGE 70
Naming Input & Output Ports 57 Naming Input & Output Ports 1 You can specify Long and Short names for the Input and Output Ports as follows. These names appear on the Input and Output Patch pages. See page 215 for a list of the initial Input Port names; page 216 for Output Port names. Use the DISPLAY ACCESS [SETUP] button to locate the Input Port or Output Port Name page. 2 Use the Parameter wheel or INC/DEC buttons to select the ports.
PAGE 71
58 Chapter 6—Input & Output Patching Patching with the Encoders 1 The following patches can be made by using the Encoders: Input Channel Inputs, Insert Outs, Insert Ins, and Direct Outs. Assign one of the above parameters to an Encoder ASSIGN button, as explained on page 37. 2 Press the ASSIGN button to which you assigned the patch parameter. 3 Use the Encoders to select ports, and press the Encoder push switches to set them. The coresponding Patch page appears when an Encoder is operated.
PAGE 72
Input Channels 59 7 Input Channels Patching Input Channels AD Inputs, Slot Inputs, internal effects processor outputs, Digital or Analog 2TR Inputs, Bus Outs, or Aux Sends can be patched to the Input Channel Inputs. See “Patching Input Channels” on page 52 for more information. Metering Input Channels Input Channel signal levels can be metered on the Meter pages. See “Metering” on page 87 for more information.
PAGE 73
60 Chapter 7—Input Channels Gating Input Channels Each Input Channel features a noise Gate for automatically shutting out unwanted noise. Gate settings can be stored in the Gate library, which contains 4 preset memories and 88 user memories. See “Gate Library” on page 127 for more information. Preset Gates & Types The following table lists the preset Gates and types. See page 255 for detailed parameter information.
PAGE 74
Attenuating Input Channels 61 3 Use the SELECTED CHANNEL DYNAMICS [DISPLAY] button to locate the Gate Edit page. 4 Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] button to set them. KEYIN SOURCE: This determines the trigger source for the currently selected Input Channel’s Gate. Trigger sources include SELF (the Gate’s own input signal), CHANNEL (another Input Channel), or AUX (an Aux Send from 1–8).
PAGE 75
62 Chapter 7—Input Channels Grouping Input Channel EQs 1 Input Channel EQs can be grouped, allowing you to control the EQ of several Input Channels simultaneously. There are four Input Channel EQ groups: a, b, c, and d. Use the DISPLAY ACCESS [GROUP] button to locate the Input Equalizer Link page. 2 Use the LAYER buttons to select the Layers. The corresponding group row is selected as each Layer is selected. 3 Use the Up/Down cursor buttons to select EQ groups a–d.
PAGE 76
Grouping Input Channel Compressors 63 Grouping Input Channel Compressors 1 Input Channel Compressors can be grouped, allowing you to control the compression of several Input Channels simultaneously by operating any Compressor control in the group. There are four Input Channel Compressor groups: i, j, k, and l. Use the DISPLAY ACCESS [GROUP] button to locate the Input Comp Link page. 2 Use the LAYER buttons to select the Layers. The corresponding group row is selected as each Layer is selected.
PAGE 77
64 Chapter 7—Input Channels Grouping Input Channel Mutes (ON/OFF) 1 Input Channel Mutes can be grouped, allowing you to mute several Input Channels simultaneously. There are eight Input Channel Mute groups: I, J, K, L, M, N, O, and P. Use the DISPLAY ACCESS [GROUP] button to locate the Input Channel Mute Group pages. The Mute group parameters for the 56 Input Channels are divided between two pages. The Input Channel 1–48 Mute Group page is shown below. The layout of the other page is the same.
PAGE 78
65 Setting Input Channel Levels Setting Input Channel Levels 1 Input Channel levels can be set as follows. Use the LAYER buttons to select the Layers. 2 Press the FADER MODE [FADER] button to select Fader mode. 3 Use the faders to set the Input Channel levels. Refer to the legend on the left side of the faders when setting Input Channel levels. Fader positions can be viewed on the Fader View pages. See “Viewing Channel Fader Settings” on page 109 for more information.
PAGE 79
66 Chapter 7—Input Channels Routing Input Channels Each Input Channel can be routed to the Bus Outs, Stereo Out, or its own Direct Out. Using the SELECTED CHANNEL ROUTING Controls 1 Use the LAYER buttons to select the Layers, and use the [SEL] buttons to select the Input Channels. ROUTING DISPLAY 1 2 2 Use the [1–8], [STEREO], and [DIRECT] buttons to route the currently selected Input Channel. [1–8]: These buttons route the currently selected Input Channel to the Bus Outs.
PAGE 80
67 Panning Input Channels The currently selected Surround mode is displayed in the lower-left corner. When Stereo mode is selected, the Bus Out routing buttons display numbers from 1 through 8. When a Surround Pan mode is selected, they display abbreviations of the Surround Channel names, as shown in the following table. See “Using Surround Pan” on page 69 for more information. Surround Mode Bus Outs 1 2 3 4 5 6 7 8 Stereo 1 2 3 4 5 6 7 8 3-1 L R C S 5 6 7 8 C E1 7 8 5.
PAGE 81
68 Chapter 7—Input Channels Pan Pages 1 2 Pan settings can be viewed and set on the Pan pages. If the Auto PAN/SURROUND Display preference is on, these pages appear automatically when a control in the SELECTED CHANNEL PAN/SURROUND section is operated. If both the [LINK] and [GRAB] button indicators are on, these pages will also appear when the Joystick is operated. See “Auto PAN/SURROUND Display” on page 197. Use the SELECTED CHANNEL PAN/SURROUND [DISPLAY] button to select the Input Channel Pan pages.
PAGE 82
69 Using Surround Pan Using Surround Pan The 02R96 supports 3-1 and 5.1 Surround modes. Surround pan is independent of normal panning. Normal panning determines how an Input Channel signal is panned between the left and right channels of the Stereo out, whereas surround panning determines how an Input Channel signal is panned among the Surround channels (i.e., the Bus Outs). The following table shows how Surround channels are handled by the Bus Outs.
PAGE 83
70 Chapter 7—Input Channels Using the Joystick 1 Use the LAYER buttons to select the Layers, and use the [SEL] buttons to select the Input Channels. PAN / SURROUND DISPLAY L 2 R L R ODD EVEN LINK GRAB EFFECT Press the [GRAB] button to grab the current Joystick position, and then use the Joystick to set the surround pan.
PAGE 84
Using Surround Pan 71 You can move the surround pan directly to one of the speaker icons, including the box icons without speakers, by selecting its icon, and then pressing [ENTER]. 3 Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] button to set them. LFE: This sets the level of the LFE (Low Frequency Effects) Channel (5.1 mode only). DIV (divergence): This determines how the Center signal is fed to the Left, Right, and Center channels.
PAGE 85
72 Chapter 7—Input Channels L/R: These parameters are used to set the left/right surround position. While selected, they can quickly be set to center by pressing [ENTER]. F/R: These parameters are used to set the front/rear surround position. While selected, they can quickly be set to center by pressing [ENTER]. You can jump to the more detailed Surround Edit page by pressing [ENTER] while an Input Channel’s surround graph is selected.
PAGE 86
Stereo Out 73 8 Stereo Out Stereo Out Connectors The Stereo Out is output by the STEREO OUT +4 dB (BAL) balanced XLR-3-32-type connectors and the STEREO OUT –10 dBV (UNBAL) unbalanced phono connectors. Patching the Stereo Out to Outputs The left and right channels of the Stereo Out can be patched to the Slot Outputs, Omni Outs, or the 2TR Digital Outputs. See “Output Patching” on page 54 for more information.
PAGE 87
74 Chapter 8—Stereo Out Stereo Out Inserts Internal effects processors and external signal processors can be patched into the Stereo Out by using the Inserts. See “Using Inserts” on page 95 for more information. Compressing the Stereo Out Signal dynamics can be controlled by using the Stereo Out Compressor. See “Compressing Channels” on page 97 for more information. Grouping Master Compressors The Stereo Out Compressor can be grouped with the Compressors of other Output Channels.
PAGE 88
Balancing the Stereo Out 75 Balancing the Stereo Out 1 The left and right channels of the Stereo Out can be balanced as follows. Press the STEREO [SEL] button to select the Stereo Out. PAN / SURROUND DISPLAY L 2 R L R ODD EVEN Use the Pan control to set the balance. The pan display indicates the balance. When the balance is set to center, the center two segments light up. The balance can be set to center by pressing [ENTER]. The Stereo Out balance can also be set on the Stereo Fader View page.
PAGE 89
76 Chapter 9—Bus Outs 9 Bus Outs Patching Bus Outs to Outputs Bus Outs can be patched to the Slot Outputs, Omni Outs, or the 2TR Digital Outputs. See “Output Patching” on page 54 for more information. Routing Input Channels to Bus Outs Input Channels can be routed to the Bus Outs. See “Routing Input Channels” on page 66 for more information. Metering Bus Outs Bus Out signal levels can be metered on the Meter pages. See “Metering” on page 87 for more information.
PAGE 90
77 Muting Bus Outs (ON/OFF) Muting Bus Outs (ON/OFF) 1 2 Bus Outs can be muted by using the channel strip [ON] buttons. Press the LAYER [MASTER] button to select the Master Layer. Use channel strip [ON] buttons 17–24 to mute the Bus Outs. The [ON] button indicators of Bus Outs that are on light up. ON Grouping Master Mutes (ON/OFF) Bus Out Mutes can be grouped with the Mutes of other Output Channels. See “Grouping Output Channel Mutes (ON/OFF)” on page 107 for more information.
PAGE 91
78 Chapter 9—Bus Outs Sending Bus Outs to the Stereo Out 1 2 Bus Outs can be routed to the Stereo Out buses as follows. Bus Out to Stereo Out settings can be stored in the Bus to Stereo library, which contains 1 preset memory and 32 user memories. See “Bus to Stereo Library” on page 126 for more information. Use the SELECTED CHANNEL ROUTING [DISPLAY] button to locate the Bus to Stereo page.
PAGE 92
Aux Sends 79 10 Aux Sends Patching Aux Send Masters to Outputs Aux Send Masters can be patched to the Slot Outputs, Omni Outs, or the 2TR Digital Outputs. See “Output Patching” on page 54 for more information. Setting the Aux Send Mode 1 Aux Sends have two operating modes—Variable and Fixed—which can be set individually for each of the eight Aux Sends. In Variable mode, Aux Send levels are variable and the signal source point can be either pre-fader or post-fader.
PAGE 93
80 Chapter 10—Aux Sends Setting Aux Send Levels Aux Send levels can be set by using the faders or Encoders. Using the Faders 1 Use the LAYER buttons to select the Layers. 2 Press the FADER MODE [AUX] button to select the Aux Fader mode. 3 Use the AUX SELECT [1–8] buttons to select Aux Sends 1–8. 4 Use the faders to set the Aux Send levels. Refer to the legend on the left side of the faders when setting Aux Send levels.
PAGE 94
Aux Send Pages 81 4 To turn Aux Sends on and off, select the rotary controls, and press [ENTER]. The rotary controls of Aux Sends that are turned off, appear gray, and “OFF” appears in place of the level value. Aux Send levels can still be changed even when they’re off. 5 To set Aux Send levels, select the rotary controls, and use the Parameter wheel or INC/DEC buttons. 6 To set the Pre/Post parameters, select the PRE/POST buttons, and use the [ENTER] button or INC/DEC buttons.
PAGE 95
82 Chapter 10—Aux Sends Viewing Aux Send Settings You can view and set settings of all Aux Sends on the Aux View pages. Level and Pre/Post parameters are displayed separately. Level Parameters 1 In Level mode, the Aux View pages display Aux Send Level and On/Off parameters. Fixed mode Aux Sends can be turned on and off only. Use the AUX SELECT [DISPLAY] button to select the Aux View pages. 2 Select the DISPLAY LEVEL button, and press [ENTER].
PAGE 96
Viewing Aux Send Settings 83 Pre/Post Parameters 1 In Pre/Post mode, the Aux View pages display Aux Send Pre/Post parameters. Fixed mode Aux Sends can be turned on and off only. Use the AUX SELECT [DISPLAY] button to select the Aux View pages. 2 Select the DISPLAY PRE/POST button, and press [ENTER]. The Input Channel 1–24 Aux View page is shown below in Pre/Post mode. The layout of the other two Aux View pages in Pre/Post mode is the same.
PAGE 97
84 Chapter 10—Aux Sends Panning Aux Sends 1 When Aux Sends are paired, Aux Sends can be panned between the paired Aux buses. See “Pairing Channels” on page 104 for more information. If the selected Aux Send is not paired, the message “AUXx–x are not paired” appears.
PAGE 98
Metering Aux Send Masters 85 Metering Aux Send Masters Aux Send Master levels can be metered on the Meter pages. See “Metering” on page 87 for more information. Monitoring Aux Send Masters Aux Send Masters can be assigned to the CONTROL ROOM [ASSIGN 1] or [ASSIGN 2] button for monitoring. See “Control Room Monitoring” on page 114 for more information. Aux 11 and Aux 12 can be monitored via the STUDIO MONITOR OUT (see page 115).
PAGE 99
86 Chapter 10—Aux Sends Settings Aux Send Master Levels 1 Aux Send Master levels can be set as follows. Press the LAYER [MASTER] button to select the Master Layer. 2 Press the FADER MODE [FADER] button to select the Fader mode. 3 Use faders 9–16 to set the Aux Send Master levels. Refer to the legend on the right side of the faders when setting Aux Send Master levels.
PAGE 100
Common Channel Functions 87 11 Common Channel Functions Metering Input Channels, Bus Outs, Aux Sends, the Stereo Out, and the effects processors can be metered on the various Meter pages, which are located by using the DISPLAY ACCESS [METER] button. Input and Output Channel Meter pages also display fader positions numerically. The Peak Hold function, which applies to all level meters, can be turned on or off on any of the Meter pages.
PAGE 101
88 Chapter 11—Common Channel Functions There are two 48-channel Meter pages. The Input Channel 1–48 Meter page is shown below. The layout of the other page is the same. Metering Output Channels Bus Outs, Aux Sends, and the Stereo Out can all be metered on the Master Meter page. Metering Effects Effects inputs and outputs are metered on the Effect 1–4 page. There are eight input and output meters for effect #1, and 2 input and output meters for effects 2 through 4.
PAGE 102
Metering 89 Metering the Stereo out The Stereo Out can be metered on the Stereo Meter page. Peak signal levels for the left and right channels are displayed numerically.
PAGE 103
90 Chapter 11—Common Channel Functions Attenuating Signals 1 Input Channels, Bus Outs, Aux Sends, and the Stereo Out all feature pre-EQ attenuation, which is useful for attenuating “hot” signals before EQ’ing. Use the EQUALIZER [DISPLAY] button to select the Attenuator pages. The Attenuator parameters for the 56 Input Channels are arranged into three pages. The Input Channel 1–24 Attenuator/Shifter page is shown below. The layout of the other two pages is the same.
PAGE 104
Using EQ 91 Using EQ Input Channels, Bus Outs, Aux Sends, and the Stereo Out all feature 4-band parametric EQ. The LOW-MID and HIGH-MID bands are peaking type. The LOW and HIGH bands can be set to shelving, peaking, or HPF and LPF respectively. EQ settings can be stored in the EQ library, which contains 40 preset memories and 160 user memories. See “EQ Library” on page 129 for more information. Preset EQs The following table lists the preset EQs. See page 251 for detailed parameter information.
PAGE 105
92 Chapter 11—Common Channel Functions # Preset Name 33 Bass Drum 3 Description A variation on preset 1, with low and mid range reduced. 34 Snare Drum 3 A variation on preset 3, creating a thicker sound. 35 Tom-tom 2 A variation on preset 5, emphasizing the mid and high ranges. 36 Piano 3 A variation on preset 13. 37 Piano Low Emphasizes the low range of pianos recorded in stereo. 38 Piano High Emphasizes the high range of pianos recorded in stereo.
PAGE 106
Using EQ 93 EQ Edit Pages 1 EQ parameters can also be set on the EQ Edit page. If the Auto EQUALIZER Display preference is on, this page appears automatically when a control in the SELECTED CHANNEL EQUALIZER section is operated. See “Auto EQUALIZER Display” on page 197. Use the EQUALIZER [DISPLAY] button to select the EQ Edit page. 2 Use the LAYER buttons to select Layers, and use the [SEL] buttons to select channels.
PAGE 107
94 Chapter 11—Common Channel Functions Grouping Output Channel EQs 1 The Bus Out, Aux Send, and Stereo Out EQs can be grouped, allowing you to control the EQ of several Output Channels simultaneously. There are four Output Channel EQ groups: e, f, g, and h. Use the DISPLAY ACCESS [GROUP] button to locate the Output Equalizer Link page. 2 Press the LAYER [MASTER] button. 3 Use the Up/Down cursor buttons to select EQ groups e–h. The selected group is highlighted by a flashing cursor box.
PAGE 108
Using Inserts 95 Using Inserts 1 Input Channels, Bus Outs, Aux Sends, and the Stereo Out all feature assignable Inserts. Use the SELECTED CHANNEL DISPLAY ACCESS [PHASE/INSERT] button to select the Insert page. The Insert page for Input Channels is shown below. The Insert page for Bus Outs, Aux Sends, and the Stereo out is shown below. 2 Use the LAYER buttons to select Layers, and use the [SEL] buttons to select channels.
PAGE 109
96 Chapter 11—Common Channel Functions selected channel’s Long name in the upper-right corner of the page. The source port can also be selected by using the Patch Select window (see page 57), which is accessed by pressing [ENTER] while this parameter is selected. Insert Ins can also be patched on the Input Channel Insert In Patch pages. See “Patching Input Channel Insert Ins” on page 53 for more information. COMP ON/OFF: This turns the currently selected channel’s Compressor on and off.
PAGE 110
Compressing Channels 97 Compressing Channels Input Channels, Bus Outs, Aux Sends, and the Stereo Out all feature a Compressor. Settings can be stored in the Comp library, which contains 36 preset memories and 88 user memories. See “Comp Library” on page 128 for more information. Preset Comps & Types The following table lists the preset Comps and types. See page 255 for detailed parameter information. # Preset Name Type Description 1 Comp COMP Compressor intended to reduce the overall volume level.
PAGE 111
98 Chapter 11—Common Channel Functions # Preset Name Type Description 27 Hip Comp COMPAND-S A variation on preset 26, intended for sampled loops and phrases. 28 Solo Vocal1 COMP Compressor for use with main vocals. 29 Solo Vocal2 COMP A variation on preset 28. 30 Chorus COMP A variation on preset 28, intended for choruses. 31 Click Erase EXPAND Expander for removing a click track that may bleed through from a musicians headphones.
PAGE 112
Compressing Channels 99 3 Use the SELECTED CHANNEL DYNAMICS [DISPLAY] button to locate the Comp Edit page. 4 Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] button to set them. POSITION: This determines the position of the Compressor within the channel, and can be set to pre-EQ, pre-fader, or post-fader. It works in unison with the COMP POSITION parameter on the Insert page. See “Using Inserts” on page 95 for more information.
PAGE 113
100 Chapter 11—Common Channel Functions Grouping Output Channel Compressors 1 The Bus Out, Aux Send, and Stereo Out Compressors can be grouped, allowing you to control the compression of several Output Channels simultaneously. There are four Output Channel Compressor groups: m, n, o, and p. Use the DISPLAY ACCESS [GROUP] button to locate the Output Comp Link page. 2 Press the LAYER [MASTER] button. 3 Use the Up/Down cursor buttons to select Comp groups m–p.
PAGE 114
Delaying Channel Signals 101 Delaying Channel Signals 1 Input Channels, Bus Outs, Aux Sends, and the Stereo Out all feature independent Delay functions. Input Channel Delays feature feedback, with independent Mix and Gain parameters. Use the SELECTED CHANNEL DISPLAY ACCESS [DELAY] button to select the Delay pages. The Delay parameters for the 56 Input Channels are arranged into three pages. The Input Channel 1–24 Delay page is shown below. The layout of the other two pages is the same.
PAGE 115
102 Chapter 11—Common Channel Functions MIX: This parameter, available only on the Input Channel Delay pages, sets the mix of dry and wet signals. FB.GAIN: This parameter, available only on the Input Channel Delay pages, sets the amount of feedback. Soloing Channels 1 2 Input Channels, Bus Outs, and Aux Sends can be soloed as follows. Use the LAYER buttons to select the Input Channel Layers if you want to solo Input Channels, or select the Master Layer if you want to solo Output Channels.
PAGE 116
Soloing Channels 103 that are routed to the Stereo Out can be soloed in this mode. Input Channels that are off are temporarily turned on when they are soloed. SEL MODE: This determines the Solo Select mode: Mix Solo or Last Solo. In Mix Solo mode, any number of channels can be soloed simultaneously. In Last Solo mode, only one channel can be soloed at a time. LISTEN: This determines the source of the Input Channel Solo signal: Pre Fader or After Pan. It does not affect Mixdown Solo mode.
PAGE 117
104 Chapter 11—Common Channel Functions Pairing Channels Input Channels, Bus Outs, and Aux Sends can be paired for stereo operation. Input Channels can be paired either horizontally, that is, adjacent odd-even channels on the same Layer (e.g., 1-2, 3-4, 5-6, etc) or vertically, that is, counterpart channels on adjacent Layers (e.g., 1-25, 2-26, 49-73, 50-74, etc). Bus Outs and Aux Sends can be paired only horizontally.
PAGE 118
Pairing Channels 2 105 To set the pair mode, select the PAIR MODE HORIZONTAL or VERTICAL buttons, and press [ENTER]. The Pair mode can be set independently for Input Channels 1–48 and Input Channels 49–56. The Input Channel 1–48 Pair page in Vertical mode is shown below. Pair parameters for the Bus Outs and Aux Sends appear on the Output Pair page. 3 Use the cursor buttons or Parameter wheel to select the channel pair buttons, and press [ENTER] to make or break pairs.
PAGE 119
106 Chapter 11—Common Channel Functions When a Surround mode other than Stereo is selected, Aux Sends can be set to follow the same Input Channel Surround Pan that applies to the Bus Outs, which is useful for feeding Surround channel signals to external effects processors. This is turned on and off by using the F.S buttons that appear below the Aux Send Pair buttons.
PAGE 120
Grouping Output Channel Mutes (ON/OFF) 107 Grouping Output Channel Mutes (ON/OFF) 1 The Bus Out, Aux Send, and Stereo Out mutes can be grouped, allowing you to mute several Output Channels simultaneously. There are four Output Channel Mute groups: U, V, W, and X. Use the DISPLAY ACCESS [GROUP] button to locate the Output Mute Group page. 2 Press the LAYER [MASTER] button. 3 Use the Up/Down cursor buttons to select Mute groups U–X. The selected group is highlighted by a flashing cursor box.
PAGE 121
108 Chapter 11—Common Channel Functions Viewing Channel Parameter Settings 1 The parameter setting of the currently selected Input Channel, Bus Out, Aux Send, or the Stereo Out can be viewed and set on the Parameter View pages. Use the DISPLAY ACCESS [VIEW] button to select the Parameter View page. 2 Use the LAYER buttons to select Layers, and use the [SEL] buttons to select channels.
PAGE 122
Viewing Channel Fader Settings 109 Output Channels This is the Parameter View page for the Bus Outs, Aux Sends, and the Stereo Out. Parameters are the same as for the Input Channel Parameter View page, minus the GATE and Phase sections and the DELAY MIX and FB GAIN parameters. The parameter settings of the left and right channels of the Stereo Out can be viewed individually. Use the [SEL] buttons to toggle between the left and right channels.
PAGE 123
110 Chapter 11—Common Channel Functions numerically below the fader. See “Setting Input Channel Levels” on page 65 for more information. SURROUND PAN: The Surround pan parameters for the currently selected Input Channel are displayed only when a Surround mode other than Stereo is selected. See “Using Surround Pan” on page 69 for more information. BUS ROUTING: This section contains Routing and Follow Pan buttons for the currently selected Input Channel.
PAGE 124
Viewing Channel Fader Settings 111 Aux Sends Below is the Fader View page for the Aux Sends. ON/OFF: This is the On/Off parameter of the currently selected Aux Send. See “Aux Send Pages” on page 80 for more information. Fader: This indicates the fader position of the currently selected Aux Send. The fader knob appears highlighted when the fader is set to 0.0 dB. The fader position is displayed numerically below the fader. See “Settings Aux Send Master Levels” on page 86.
PAGE 125
112 Chapter 11—Common Channel Functions Naming Channels You can specify Long and Short names for the Input Channels, Bus Outs, Aux Sends, and the Stereo Out as follows. See page 214 for a list of initial Input Channel names; page 214 for Output Channel names. Input Channels 1 Use the DISPLAY ACCESS [INPUT PATCH] button to locate the Input Channel Name page. 2 Use the Parameter wheel, INC/DEC buttons, or the LAYER and [SEL] buttons to select the Input Channels.
PAGE 126
Naming Channels 113 2 Use the Parameter wheel, INC/DEC buttons, or the Master Layer and [SEL] buttons to select the Output Channels. 3 Use the cursor buttons to select the Output Channel’s Long or Short name, and then press [ENTER]. When the Title Edit window appears, edit the Output Channel name, and press OK when you’ve finished. See “Title Edit Window” on page 32 for more information. You can reset all Output Channel names back to their initial values by pressing the INITIALIZE button.
PAGE 127
114 Chapter 12—Monitoring & Talkback 12 Monitoring & Talkback Control Room Monitoring The CONTROL ROOM MONITOR OUT uses balanced 1/4-inch phone jacks, nominal level +4 dB. Typically it’s used to feed the control room’s main monitors. The Control Room Monitor signal source is selected by using the CONCONTROL ROOM TROL ROOM buttons. [2TR D1]: Selects the 2TR IN DIGITAL AES/EBU 1. [2TR D2]: Selects the 2TR IN DIGITAL COAXIAL 2. [2TR D3]: Selects the 2TR IN DIGITAL COAXIAL 3.
PAGE 128
Studio Monitoring 115 Control Room Setup 1 Control room monitoring is configured on the Control Room Setup page. Use the MONITOR [DISPLAY] button to locate the Control Room Setup page. 2 Use the cursor buttons to select the ASSIGN buttons in the left-hand box, and use the Parameter wheel to select an Output Channel in the right-hand box. Bus Outs or Aux Sends can be assigned to the [ASSIGN 1] and [ASSIGN 2] buttons. 3 Press [ENTER] to assign the selected Output Channel.
PAGE 129
116 Chapter 12—Monitoring & Talkback Surround Monitoring The 02R96 features comprehensive surround monitoring functions, including a pink noise generator for speaker setup, Bass Management, and down mixing. The Surround pages explained in this section are available only when a Surround mode other than Stereo is selected (see page 69). The Surround Monitor signal source is selected by using the SURROUND buttons. The [BUS] button selects the Bus Outs as the source.
PAGE 130
Surround Monitoring 117 When the MONITOR L/R to C-R button is on, the Left and Right Surround Monitor Channels are fed to the Control Room Monitors. This is useful when you want to use the same speakers for Left and Right Surround Monitors and Control Room Monitors. STATUS: SURROUND MODE indicates the currently selected Surround mode, which is set on the Surround Mode page (see page 69).
PAGE 131
118 Chapter 12—Monitoring & Talkback MONITOR MATRIX: This is used to select the Surround Monitor Matrix. In 5.1 Surround mode, you can select 5.1, 3-1, or ST. In 3-1 Surround mode, you can select 3-1 or ST. The ATT parameters can be used to attenuate individual Surround Channel signals. The following diagrams, which show the Monitor Matrixes available in each Surround mode, are displayed when this parameter is selected. 3-1 to 3-1 3-1 to ST 5.1 to 5.1 5.1 to 3-1 5.
PAGE 132
Surround Monitoring 119 The following diagrams show the Bass Management configuration for each monitor matrix setting, with Bass Management turned on and off. 5.1 ON 3-1 ON ST ON 5.1 OFF 3-1 OFF ST OFF MONITOR ALIGNMENT ATT & DLY ON/OFF: These buttons are used to turn on and off the Monitor Alignment Attenuator and Delay parameters of all Surround speakers.
PAGE 133
120 Chapter 12—Monitoring & Talkback Patching Slot Inputs to Surround Channels 1 2 Individual Slot Inputs can be patched to Surround Monitor Channels as follows. Use the MONITOR [DISPLAY] button to locate the Surround Monitor Patch page. Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] button to set them. SLOT/CH: This patching matrix is used to patch Inputs 1–8 from each of the four Slots to Surround Monitor Channels 1–8.
PAGE 134
Using Talkback 121 Using Talkback The Talkback function distributes the Talkback mic signal to the Studio Monitor Outs and any Slot or Omni Outputs specified on the Talkback Setup page. The TALKBACK LEVEL control sets the level of the built-in talkback microphone. 0 10 TALKBACK LEVEL TALKBACK The [TALKBACK] button has two modes of operation: If it’s pressed once (i.e., for less than 300 ms), the Talkback function is turned on and remains on when the button is released.
PAGE 135
122 Chapter 13—Libraries 13 Libraries About the Libraries The 02R96 features 10 libraries for storing Automix, Effects, Channel, Input Patch, Output Patch, Bus to Stereo, Gate, Comp, EQ, and Surround Monitor data. Library data can be stored to an external MIDI device, such as a MIDI data filer, by using MIDI Bulk Dump (see page 168). General Library Operation 1 Since most library functions are the same for each library, rather than explain them several times, they’re explained only here for conciseness.
PAGE 136
Channel Library 123 Channel Library 1 2 Input Channel, Bus Out, Aux Send, and Stereo Out channel settings can be stored in the Channel library, which contains 2 preset memories and 127 user memories. Use the DISPLAY ACCESS [VIEW] button to select the Channel Library page. Use the LAYER buttons to select Layers, and the [SEL] buttons to select channels. When storing, the settings of the currently selected channel are stored to the selected memory.
PAGE 137
124 Chapter 13—Libraries Input Patch Library 1 Input Patch settings can be stored in the Input Patch library, which contains 1 preset memory and 32 user memories. See page 52 for information on Input Patch settings. Use the DISPLAY ACCESS [INPUT PATCH] button to select the Input Patch Library page. When storing, the current Input Patch settings are stored to the selected memory. For details on the Store, Recall, Title Edit, and Clear functions, see “General Library Operation” on page 122.
PAGE 138
Effects Library 125 Effects Library 1 2 Effects settings can be stored in the Effects library, which contains 52 preset memories and 76 user memories. See page 131 for information on using the Effects. Use the EFFECTS/PLUG-INS [DISPLAY] button to select the Effect Library page. Press the EFFECTS/PLUG-INS [INTERNAL EFFECTS] button, and use the EFFECTS/PLUG-INS [1–4] buttons to select the internal effects processors.
PAGE 139
126 Chapter 13—Libraries Bus to Stereo Library 1 Bus to Stereo settings can be stored in the Bus to Stereo library, which contains 1 preset memory and 32 user memories. See page 78 for information on Bus to Stereo routing. Use the ROUTING [DISPLAY] button to select the Bus to Stereo Library page. When storing, the current Bus Out to Stereo Out settings are stored to the selected memory. CURRENT CONFIGURATION: Bus Out pairing information for the current configuration is displayed here.
PAGE 140
Gate Library 127 Gate Library 1 2 Input Channel Gate settings can be stored in the Gate library, which contains 4 preset memories and 124 user memories. See page 60 for information on gating Input Channels. Use the DYNAMICS [DISPLAY] button to select the Gate Library page. Use the LAYER buttons to select the Layers, and the [SEL] buttons to select Input Channels.
PAGE 141
128 Chapter 13—Libraries Comp Library 1 2 Comp settings can be stored in the Comp library, which contains 36 preset memories and 92 user memories. See page 97 for information on the Comps. Use the DYNAMICS [DISPLAY] button to select the Comp Library page. Use the LAYER buttons to select Layers, and the [SEL] buttons to select channels. When storing, the Comp settings of the currently selected channel, indicated in the upper-right corner, are stored to the selected memory.
PAGE 142
EQ Library 129 EQ Library 1 2 Input Channel, Bus Out, Aux Send, and Stereo Out EQ settings can be stored in the EQ library, which contains 40 preset memories and 160 user memories. See page 91 for information on EQ’ing. Use the EQUALIZER [DISPLAY] button to select the EQ Library page. Use the LAYER buttons to select Layers, and the [SEL] buttons to select channels.
PAGE 143
130 Chapter 13—Libraries Automix Library 1 Up to 16 Automixes can be stored in the Automix library. See page 145 for information on using Automix. Use the AUTOMIX [DISPLAY] button to select the Automix Memory page. When storing, the current Automix is stored to the selected memory. TITLE: This is the title of the current Automix. CURRENT: This is the size of the current Automix. FREE: This is the amount of free memory for storing the current Automix.
PAGE 144
Internal Effects & Plug-Ins 131 14 Internal Effects & Plug-Ins About the Effects The 02R96 features four internal multi-effects processors, offering a whole host of effects types, including reverbs, delays, modulation-based effects, combination effects, and multichannel effects designed especially for use with surround sound. Effects processors 2–4 feature assignable stereo inputs and outputs.
PAGE 145
132 Chapter 14—Internal Effects & Plug-Ins Modulation-based Effects # Preset Name Type Description 13 Chorus CHORUS Chorus 14 Flange FLANGE Flanger 15 Symphonic SYMPHONIC Proprietary Yamaha effect that produces a richer and more complex modulation than normal chorus 16 Phaser PHASER 16-stage stereo phase shifter 17 Auto Pan AUTO PAN Auto-panner 18 Tremolo TREMOLO Tremolo 19 HQ.Pitch HQ.
PAGE 146
Editing Effects 133 Others # Preset Name 41 Multi.Filter Type MULTI.FILTER Description 3-band parallel filter (24 dB/octave) 42 Freeze FREEZE Simple sampler 43 Stereo Reverb ST REVERB Stereo reverb 441 Reverb 5.1 REVERB 5.12 6-channel reverb for 5.1 surround 451 Octa Reverb OCTA 461 Auto Pan 5.1 AUTO PAN 5.1 6-channel auto pan for 5.1 surround 471 Chorus 5.1 CHORUS 5.1 6-channel chorus for 5.1 surround 481 Flange 5.1 FLANGE 5.1 6-channel flanger for 5.1 surround 491 Sympho. 5.
PAGE 147
134 Chapter 14—Internal Effects & Plug-Ins TYPE: This is the effects type used in the previously recalled Effects memory. Its I/O configuration is shown below this. MIX BALANCE: This is used to set the balance between the wet and dry signals. When set to 0%, only the dry signal is heard. When set to 100%, only the wet signal is heard. BYPASS: This button is used to bypass the currently selected effects processor.
PAGE 148
About Plug-Ins 135 About Plug-Ins There are two types of Plug-Ins: Waves Plug-Ins and User Defined Plug-Ins. Waves Plug-Ins are available on Y56K cards, which need to be installed in the 02R96’s mini YGDAI Slots (Slots 3 and 4 only). See your Yamaha dealer for details. User Defined Plug-Ins can be used to control up to 32 user definable parameters via MIDI Control Change or Parameter Change messages on an external MIDI device, such as an external effects processor.
PAGE 149
136 Chapter 14—Internal Effects & Plug-Ins Editing Plug-Ins 1 Plug-Ins can be edited as follows. The settings of Waves Plug-Ins and User Defined Plug-In banks can be stored to an external MIDI device, such as a MIDI data filer, by using MIDI Bulk Dump (see page 168). If you’ve installed a Y56K card into one of the Slots, display pages especially for the Waves card are displayed when the corresponding Plug-In is selected. See the Waves documentation for more information.
PAGE 150
Editing Plug-Ins 137 MIN/MAX: These parameters determine the minimum and maximum values of the MIDI data transmitted when each parameter control is adjusted. Use the PARAMETER ID/NAME parameter to select a Parameter ID from 1–4, and then edit as necessary. VAL: This is used to select the format for converting parameter control values to the DATA parameter’s VAL setting. It applies to the currently selected bank. The available options are listed in the following table.
PAGE 151
138 Chapter 15—Scene Memories 15 Scene Memories About Scene Memories Scene memories allow you to store a snapshot of virtually every 02R96 mix setting in a Scene. There are 99 Scene memories, and they can be titled for easy identification. Scenes can be linked to Input and Output Patch library memories, so that input and output patches are recalled along with Scenes. A fade time of up to 30 seconds can be set individually for each Input and Output Channel fader.
PAGE 152
Auto Scene Memory Update 139 Scene Memories #0 & #U Scene memory #0 is a special read-only memory that contains the initial settings of all mix parameters. It can be recalled, but not stored. When you want to reset all mix parameters to their initial, or default values, recall Scene memory #0. Input Channel faders are set to either –∞dB or nominal, depending on the Initial Data Nominal preference (see page 198).
PAGE 153
140 Chapter 15—Scene Memories Storing & Recalling Scenes with the SCENE MEMORY Buttons As each Scene memory is selected, its number flashes on the SCENE MEMORY display, and its number and title flash in the Scene memory section of the display. These stop flashing when the selected Scene memory is either stored or recalled. Empty Scene memories have the title “No Data!” and cannot be recalled. You cannot store to Scene memories that are write-protected.
PAGE 154
Using the Scene Memory Page 141 Using the Scene Memory Page 1 On the Scene Memory page you can store, recall, write-protect, delete, and edit the titles of Scenes. Use the SCENE MEMORY [DISPLAY] button to locate the Scene Memory page. 2 Use the Parameter wheel or INC/DEC buttons to select the Scene memories. A Scene memory is selected when it appears inside the dotted box. 3 Use the cursor buttons to select the following buttons.
PAGE 155
142 Chapter 15—Scene Memories Fading Scenes 1 Fade times can be specified for individual Input Channels, Bus Outs, Aux Sends, and the Stereo Out. The fade time determines the time it takes the Input and Output Channel faders to move to their new positions when a Scene is recalled. You must store these settings in a Scene beforehand in order for them to take effect. Fade time settings can be specified for each Scene individually. Use the SCENE MEMORY [DISPLAY] button to locate a Fade Time page.
PAGE 156
Recalling Scenes Safely 143 Recalling Scenes Safely 1 When a Scene is recalled, all mix parameters are set accordingly. In some situations, you may want to retain the settings of certain parameters on certain channels, and this can be achieved by using the Recall Safe function. Recall Safe can be set individually for Input Channels, Bus Outs, Aux Sends, and the Stereo Out. Use the SCENE MEMORY [DISPLAY] button to locate the Recall Safe page.
PAGE 157
144 Chapter 15—Scene Memories Sorting Scenes 1 Scene can be sorted by using the Scene Memory Sort function. Use the SCENE MEMORY [DISPLAY] button to locate the Scene Memory Sort page. 2 Use the cursor button to the select the SOURCE list, and use the Parameter wheel or the INC/DEC buttons to select the Scene memory you want to move.
PAGE 158
Automix 145 16 Automix About Automix The 02R96’s Automix function allows dynamic automation of virtually all mix parameters, including Levels, Mutes, Pan, Surround Pan, Aux Sends, Aux Send Mutes, EQ, effects, and Plug-Ins. You can specify which of these parameters will be recorded, and punch channels in and out of recording on-the-fly. User Defined Remote Layer operations, and scene and library recall operations can also be automated, combining snap shot and dynamic mix automation.
PAGE 159
146 Chapter 16—Automix Automix Main Page 1 2 This section explains the Automix Main page. Use the DISPLAY ACCESS [AUTOMIX] button to locate the Automix Main page. Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] button to set them. TITLE: This is the title of the current Automix. DISABLED/ENABLED: This button is used to enable and disable the Automix function. TIME CODE: This counter displays the current timecode position.
PAGE 160
Automix Main Page TO END 147 Return Takeover or Off At the point at which recording is stopped, the fader returns to the position specified by the existing fader data, at the speed specified by the Time parameter on the Fader Edit pages. At the point at which recording is stopped, the fader remains at the same position until the next Fader event in the existing data occurs.
PAGE 161
148 Chapter 16—Automix FADER EDIT: These buttons are used to set the Fader Edit mode: Absolute or Relative. The Fader Edit mode determines how fader moves are rerecorded. It has no effect during the first recording pass. In Absolute mode, fader moves are rerecorded as absolute values and existing fader data is erased. In Relative mode, fader moves are rerecorded relative to the existing fader data.
PAGE 162
Channel Strip [AUTO] Buttons 149 AUTO REC: This button works the same as the REC button except that it remains on when Automix recording is stopped. It appears highlighted while Auto Record mode is on. REC: This button is used to engage Record-Ready mode, in which Automix recording starts automatically as soon as the specified timecode source starts. Unlike the AUTO REC button, however, it’s turned off when recording is stopped. It flashes in Record-Ready mode, and is highlighted during recording.
PAGE 163
150 Chapter 16—Automix Automix Memory Page 1 2 Automixes can be stored and recalled on the Automix Memory page. The lower half of this page is identical to the Automix Main page. Use the DISPLAY ACCESS [AUTOMIX] button to locate the Automix Memory page. Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] button to set them. The Automix library functions are explained in “Automix Library” on page 130.
PAGE 164
Fader Edit Pages 151 Fader Edit Pages 1 2 During playback, fader positions are displayed graphically as black bars on the Fader Edit page, of which there are two. The Fader Edit 1 page displays Faders positions for Input Channel 1 through 56, the Bus Outs, and Stereo Out. The Fader Edit 2 page displays faders positions for Input Channel 1 through 56, the Bus Outs, and Aux Sends. When the Fader mode is set to Fader, Input and Output Channel levels are displayed.
PAGE 165
152 Chapter 16—Automix Selecting the Timecode Source & Frame Rate 1 2 The timecode source and frame rate for Automix can be set as follows. Use the DISPLAY ACCESS [SETUP] button to select the Time Reference page. Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] button to set them. TIME REFERENCE: The following timecode sources can be selected.
PAGE 166
Creating a Time Signature Map 153 Creating a Time Signature Map 1 2 When using the MIDI CLOCK timecode source, you’ll also need to specify the initial time signature and any time signature changes that follow. Use the DISPLAY ACCESS [SETUP] button to select the Time Signature page. Use the cursor buttons to select the parameters, and use the Parameter wheel or INC/DEC buttons to specify the measure and time signature.
PAGE 167
154 Chapter 16—Automix Recording an Automix 1 This section provides a general procedure for Automix recording. Connect a timecode source. 2 Select the timecode source and frame rate. See “Selecting the Timecode Source & Frame Rate” on page 152 for more information. 3 Use the DISPLAY ACCESS [AUTOMIX] button to locate the Automix Main page. 4 On the Automix Main page, use the ENABLED/DISABLED button to enable the Automix function.
PAGE 168
Parameter Recording 155 Parameter Recording The following table summarizes parameter recording operation for each parameter. Parameter adjustments made on the respective display pages are also recorded.
PAGE 169
156 Chapter 16—Automix Punching In & Out Individual Parameters During Automix rerecording, channels can be punched in and out by pressing the channel strip [AUTO] buttons. Individual parameters can be punched in and out as follows.
PAGE 170
Playing Back an Automix 157 Playing Back an Automix So long as the Automix function is enabled, the Automix function will chase the incoming timecode and play and stop the current Automix accordingly. Playback stops automatically when the end of the Automix data is reached. Playback can be stopped manually by pressing the STOP or ABORT button on the Automix Main or Memory page.
PAGE 171
158 Chapter 16—Automix Editing Events Offline Automix events can be edited offline on the Event Copy and Event Edit pages. Offline editing can be performed only while the Automix function is stopped. Event Copy Page 1 2 On the Event Copy page, specified events on specified channels between specified in and out points can be erased, copied, moved/merged, or trimmed. Use the DISPLAY ACCESS [AUTOMIX] button to locate the Event Copy page.
PAGE 172
Editing Events Offline 159 TRIM EDIT: These parameters are used to specify the TRIM IN and TRIM OUT times and the trim level, which can be set in 0.5 dB steps. The TRIM IN parameter determines the time in which the fader level must achieve the specified trim amount. The TIME SETTING IN point determines the point at which trimming starts. The TRIM OUT time determines the time from which the Fader level can start returning to the previous level.
PAGE 173
160 Chapter 16—Automix COPY button: This button is used to copy the specified Automix data. Use the channel buttons to select the source channels. Use the IN and OUT parameters to specify the region to be copied. Use the TO parameter to specify the point to which the specified data is to be copied. Use the DESTINATION parameter to specify the channels to which the specified data is to be copied. Use the PARAMETERS window to specify which Automix events are to be copied.
PAGE 174
Editing Events Offline 161 Event Edit Page 1 2 On the Event Edit page, you can edit, duplicate, delete, and insert new events. Use the DISPLAY ACCESS [AUTOMIX] button to locate the Event Edit page. Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] button to set them. Event list: Automix events are listed in chronological order. The type of events listed depends on the Event select buttons. Use the cursor buttons to select event parameters.
PAGE 175
162 Chapter 16—Automix CAPTURE button: This button is used to capture the current timecode position. Up to eight timecode values can be captured and stored in the eight Capture memories. Use the cursor buttons to select the Capture memory number, and use the Parameter wheel or the INC/DEC buttons to select the Capture memories. Capture memories can be selected even while the CAPTURE, LOCATE, or INSERT button is selected.
PAGE 176
MIDI 163 17 MIDI MIDI & the 02R96 • • • • • • • • • • The 02R96 supports the following MIDI messages: Program Changes for recalling Scenes (see page 166) Control Changes for real-time parameter control (see page 167) System Exclusive Parameter Changes for real-time parameter control (see page 167) MIDI Note On/Off for Freeze effect (see page 244) Bulk Dump for transmitting Scene, library, and setup data (see page 168) MTC and MIDI Clock for Automix synchronization (see page 152) MMC for external machine
PAGE 177
164 Chapter 17—MIDI MIDI Port Setup 1 2 MIDI ports are configured as follows. Use the DISPLAY ACCESS [SETUP] button to locate the MIDI/TO HOST Setup page. Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] button to set them. TO HOST SERIAL: These buttons are used to configure the TO HOST SERIAL port for use with either a Mac or PC. Caution: When a PC is connected to the TO HOST SERIAL port, do not set this to Mac because your PC may crash.
PAGE 178
MIDI Channel Setup 165 MIDI Channel Setup 1 2 MIDI Channels for reception and transmission are specified as follows. Use the DISPLAY ACCESS [MIDI] button to locate the MIDI Setup page. Use the cursor buttons or Parameter wheel to select the parameters, and use the INC/DEC buttons or [ENTER] button to set them. RECEIVE: The Channel buttons are used to select a MIDI Channel for MIDI message reception.
PAGE 179
166 Chapter 17—MIDI Assigning Scenes to Program Changes 02R96 Scenes can be assigned to MIDI Program Changes for remote recall. When a Scene is recalled on the 02R96, the assigned Program Change number is transmitted. If that Scene is assigned to more than one Program Change, the lowest Program Change is transmitted. Likewise, when a Program Change message is received, the assigned Scene is recalled.
PAGE 180
Assigning Parameters to Control Changes 167 Assigning Parameters to Control Changes 1 02R96 parameters can be assigned to MIDI Control Changes for real-time control. When a parameter is adjusted on the 02R96, the assigned Control Change message is transmitted. Likewise, when a Control Change message is received, the assigned 02R96 parameter is set. You must set the MIDI Setup parameters in order to transmit and receive Control Change messages (see page 165).
PAGE 181
168 Chapter 17—MIDI Using Bulk Dump 1 02R96 data can be stored to an external MIDI device, such as a MIDI data filer, by using MIDI Bulk Dump. Use the DISPLAY ACCESS [MIDI] button to locate the Bulk Dump page. 2 To transmit data, use the CATEGORY parameters to select the type of data you want to transmit, select the TRANSMIT button, and then press [ENTER]. 3 To receive data, use the CATEGORY parameters to select the type of data you want to receive, select the REQUEST button, and then press [ENTER].
PAGE 182
Pro Tools Remote Layer 169 18 Pro Tools Remote Layer The 02R96 features a Remote Layer target especially designed for controlling Pro Tools. If an optional MB02R96 Peak Meter Bridge is installed, Pro Tools channel levels are displayed on its meters. Configuring Windows Computers 1 Connect your PC. The 02R96 can be connected to your Windows PC by connecting the TO HOST SERIAL port to a suitable RS232 serial port on your PC, or by connecting the TO HOST USB port to a USB port on your PC.
PAGE 183
170 Chapter 18—Pro Tools Remote Layer Configuring Pro Tools 1 Pro Tools needs to be configured as follows. For more information, see your Pro Tools documentation. Launch Pro Tools. 2 Choose OMS Studio Setup from the Setups menu, and configure OMS as necessary. This screen shot shows the Yamaha USB MIDI driver with eight ports. An OMS-compatible device profile for the 02R96 is included on the 02R96 CD-ROM. See the included documentation for more information. 3 Choose Peripherals from the Setups menu.
PAGE 184
Control Surface Operation with the Pro Tools Remote Layer 171 Control Surface Operation with the Pro Tools Remote Layer This section explains the operation of the 02R96 control surface when the Pro Tools Remote Layer is selected. 02R96 buttons and controls are referred to by the names printed on the 02R96 with the name of the corresponding Pro Tools function in parenthesis. For example, “Press the AUX SELECT [AUX 1] (SEND A) button.
PAGE 185
172 Chapter 18—Pro Tools Remote Layer INSERT ASSIGN/EDIT Display Mode Press the [F2] button to select this mode. ASSIGN: This indicator flashes when the EFFECTS/PLUG-INS [1] (ASSIGN) button is pressed. See “Assigning Inserts/Plug-ins” on page 182 for more information. COMPARE: This indicator appears highlighted when the EFFECTS/PLUG-INS [2] (COMPARE) button is pressed. See “Editing Plug-ins” on page 183 for more information.
PAGE 186
Control Surface Operation with the Pro Tools Remote Layer 173 Meter Display Mode Press the [F4] button to select this display mode. In this display mode, stereo meters for each channel are displayed. The name of each channel is displayed below the meters. Automation mode settings, aux send destinations, and aux send pre/post settings can also be displayed here.
PAGE 187
174 Chapter 18—Pro Tools Remote Layer Faders The faders are used to set channel levels (see page 179), or to set send levels in Flip mode (see page 181). 10 5 0 5 10 15 20 30 40 50 AUX SELECT Section AUX SELECT DISPLAY AUX 1 (SEND A) AUX 2 (SEND B) AUX 3 (SEND C) AUX 4 (SEND D) AUX 5 (SEND E) AUX SELECT [AUX 1–5] buttons are used to select sends A–E. The button indicator of the currently selected send lights up.
PAGE 188
Control Surface Operation with the Pro Tools Remote Layer 175 EFFECTS/PLUG-INS Section EFFECTS / PLUG INS ( SCROLL) DISPLAY (SHOW INSERT) PLUG INS (DEFAULT) CHANNEL INSERTS 1 2 3 4 (ASSIGN) (COMPARE) (BYPASS) (INSERT/PARAM) (SCROLL ) [DISPLAY] (SHOW INSERT) button This button is used to open and close plug-in windows. [PLUG-INS] (DEFAULT) button This button is used in conjunction with other controls to reset faders, panpots, and sends to their default values.
PAGE 189
176 Chapter 18—Pro Tools Remote Layer USER DEFINED KEYS Section USER DEFINED KEYS DISPLAY (AUTO STATUS) 1 2 3 (MIX/EDIT) (SUSPEND) (WRITE) 9 10 ( BANK) (BANK ) 4 5 6 7 8 (TOUCH) (LATCH) (READ) (TRIM) (OFF) 14 15 16 11 12 13 (FADER) (MUTE) (PAN) (SEND) (SEND MUTE) (PLUG-IN) [DISPLAY] (AUTO STATUS) button This button is used to display the Automation mode settings of all channels. See “Viewing the Automation Mode” on page 187 for more information.
PAGE 190
Control Surface Operation with the Pro Tools Remote Layer 177 MACHINE CONTROL Section MACHINE CONTROL LOCATE MEMORY DISPLAY (MEM-LOC) SET 1 2 3 4 5 6 7 8 REW FF STOP PLAY REC [DISPLAY] (MEM-LOC) button This button is used to open and close the Memory Locations window. LOCATE MEMORY [1–8] buttons These buttons perform the same transport-related functions as the 1–8 number keys on a Macintosh keyboard.
PAGE 191
178 Chapter 18—Pro Tools Remote Layer Data Entry Section DEC (ESC) INC (CURSOR MODE) SHUTTLE SCRUB ENTER Parameter Wheel The Parameter wheel is used for shuttling and scrubbing (see page 186). It’s also used for making fine adjustments to the selected region (see page 185). [SHUTTLE] & [SCRUB] buttons These buttons are used to select the Shuttle and Scrub modes. See “Scrub & Shuttle” on page 186 for more information.
PAGE 192
Selecting Channels 179 Selecting Channels 1 2 Channels can be selected as follows. (Make sure the EFFECTS/PLUG-INS [CHANNEL INSERTS] button indicator is not lit before proceeding.) Use the [SEL] buttons to select channels. The [SEL] button indicators of selected channels light up. To select multiple channels in each eight-channel block (e.g., 1–8, 9–16, or 17–24), while holding down one [SEL] button, use the [SEL] buttons of the other channels in the same block to add and remove channels.
PAGE 193
180 Chapter 18—Pro Tools Remote Layer Viewing Send Destinations Send destinations can be viewed in Channel Display mode [F3] or Meter Display mode [F4] (see page 172) by pressing the holding the AUX SELECT [AUX 1–5] (SEND A–E) buttons. Configuring Sends as Pre or Post 1 2 Sends can be configured as either pre or post as follows. (Make sure the ENCODER MODE [PAN] (PAN) button indicator is not lit before proceeding.) Use the AUX SELECT [AUX 1–5] (SEND A–E) buttons to select the sends.
PAGE 194
Flip Mode 181 Flip Mode In Flip mode, the faders, Encoders, and [ON] buttons can be used to control sends, as shown in the following table. Control Normal mode Flip mode Fader Channel level Send level Encoder Channel pan/send level Send pan Encoder push-switches Encoder mode is Pan, inactive Encoder mode is Send level, Send pre/post Send pre/post [ON] button Channel mute Send mute 1 Press the FADER MODE [FADER] or [AUX] button.
PAGE 195
182 Chapter 18—Pro Tools Remote Layer Assigning Inserts/Plug-ins 1 Inserts can be assigned to channels as follows. The Pro Tools transport must be stopped in order to make these assignments. Press the EFFECTS PLUG-INS [CHANNEL INSERTS] button. Its indicator lights up and the [SEL] buttons are set to Insert Select mode. 2 Use the [SEL] buttons to select channels for insert assignment. The name of the selected channel appears in the INSERT/PARAM section of the display.
PAGE 196
Editing Plug-ins 183 Editing Plug-ins 1 Plug-ins can be edited as follows. Press the EFFECTS PLUG-INS [CHANNEL INSERTS] button. Its indicator lights up and the [SEL] buttons are set to Insert Select mode. 2 Use the [SEL] buttons to select the channel whose plug-in you want to edit. That channel’s [SEL] button indicator lights up, and the border of the corresponding channel name in the Pro Tools Mix window is highlighted red.
PAGE 197
184 Chapter 18—Pro Tools Remote Layer Bypassing Plug-ins 1 Plug-ins can be bypassed as follows. (Make sure the EFFECTS/PLUG-INS [4] (INSERT/PARAM) button indicator is not lit before proceeding.) Press the EFFECTS PLUG-INS [CHANNEL INSERTS] button. Its indicator lights up and the [SEL] buttons are set to Insert Select mode. 2 Use the [SEL] buttons to select plug-ins. 3 While holding down the EFFECTS/PLUG-INS [3] (BYPASS) button, use Parameter control 1–4 push switches to bypass the plug-ins.
PAGE 198
Zooming 185 Zooming 1 • • • • The cursor buttons can be used to zoom the Edit window as follows. Use the [INC] (CURSOR MODE) button to select Zoom cursor mode. The CURSOR MODE section of the display shows “ZOOM.” In Zoom cursor mode, the cursor buttons work as follows: Left cursor button: Zoom out horizontally. Right cursor button: Zoom in horizontally. Up cursor button: Zoom in vertically. Down cursor button: Zoom out vertically.
PAGE 199
186 Chapter 18—Pro Tools Remote Layer Scrub & Shuttle 1 The Parameter wheel can be used to scrub and shuttle as follows. Make sure that Pro Tools is stopped. 2 Press the [SCRUB] button if you want to scrub, press the [SHUTTLE] button if you want to shuttle. The corresponding button indicator lights up. The [REW] and [FF] button indicators also light up, and the cursor mode is set to Navigation (the CURSOR MODE section of the display shows “NAVIGATION”).
PAGE 200
Automation 187 Automation Viewing the Automation Mode 1 2 The Automation mode setting of each channel can be viewed as follows. Press either the [F3] or [F4] button. Channel Display mode or Meter Display mode is selected. Press and hold a channel’s [AUTO] button. The channel’s Automation mode is displayed while the [AUTO] button is pressed.
PAGE 201
188 Chapter 18—Pro Tools Remote Layer Trim Mode 1 Trim mode can be set as follows. While holding down a channel’s [AUTO] button, press the USER DEFINED KEYS [7] (TRIM) button. If channel Display mode [F3] or Meter Display mode [F4] is currently selected, the channel’s Automation mode is displayed while its [AUTO] button is pressed.
PAGE 202
Remote Control 189 19 Remote Control About the Remote Layer The 02R96’s Remote Layer allows you to control external MIDI equipment directly from the 02R96. The type of device to be controlled (i.e., the target) is specified on the Remote page. There are three types of target: User Defined, Nuendo, and Pro Tools. The User Defined target allows you to specify the MIDI data that will be transmitted when the 24 channel strip faders, Encoders, and [ON] buttons are operated.
PAGE 203
190 Chapter 19—Remote Control Configuring the User Defined Remote Layer 1 2 The User Defined Remote Layer can be configured as follows. Use the DISPLAY ACCESS [REMOTE] button to locate the Remote page. Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] button to set them. TARGET: This is used to select the target (only the User Defined target is explained in this section).
PAGE 204
Using the User Defined Remote Layer 191 when an Encoder is adjusted. For the ENC setting, the Encoder’s current value from 0–127 is transmitted when it’s adjusted. The END setting specifies the end of the data. NOP means no data is transmitted. LEARN: This works the same as the [ON] button Learn function above, except the received MIDI messages are displayed in the ENCODER DATA area. Only one Learn function can be used at a time.
PAGE 205
192 Chapter 19—Remote Control About Machine Control The 02R96 can control the transport and locate functions of up to eight external recording machines that support MMC (MIDI Machine Control). Machines that support MMC can be controlled by connecting them to the 02R96’s MIDI, SERIAL, USB, or SLOT1 (with optional mLAN I/O Card installed in Slot #1). MMC support varies from machine to machine. Some machines may not operate exactly as explained in this section.
PAGE 206
Transport Buttons 193 Transport Buttons The 02R96’s transport can be used to control external machines. The machine that is to be controlled can be selected on the Machine Configuration page (see page 192). REW FF STOP PLAY REC [REW] button This button starts rewind on the external machines. [FF] button This button starts fast forward on the external machines. [STOP] button This button stops the external machines. [PLAY] button This button starts playback on the external machines.
PAGE 207
194 Chapter 19—Remote Control Using the Locator MACHINE CONTROL LOCATE MEMORY DISPLAY (MEM-LOC) SET 1 2 3 4 5 6 7 8 LOCATE MEMORY [1–8] buttons These buttons are used to set and to locate to the eight Locate memories. Locate memories can be set on the Locate Memory page (see page 194). To set a locate memory on-the-fly, while holding down the [SET] button, press a LOCATE MEMORY [1–8] button. The 02R96 must be receiving timecode in order to do this.
PAGE 208
GPI (General Purpose Interface) 195 GPI (General Purpose Interface) 1 The 02R96’s CONTROL port (25-pin D-sub connector) provides a GPI (General Purpose Interface) for controlling external equipment. Pinouts are provided on page 271. The eight GPI outputs can be configured so that they output trigger signals when faders or USER DEFINED KEYS are operated.
PAGE 209
196 Chapter 20—Other Functions 20 Other Functions Using the User Defined Keys Up to 16 functions from a list of over 150 can be assigned to the USER DEFINED KEYS, and up to four assignment setups can be stored in banks A, B, C, and D. See page 202 for a list of initial bank assignments. Use the USER DEFINED KEYS [DISPLAY] button to locate the User defined Key Assigned page.
PAGE 210
Setting Preferences 197 Setting Preferences You can customize the operation of the 02R96 by using the preferences pages. Preferences 1 1 Use the DISPLAY ACCESS [SETUP] button to locate the Preferences 1 page. 2 Use the cursor buttons or Parameter wheel to select the preferences, and use the INC/DEC buttons or [ENTER] button to set them.
PAGE 211
198 Chapter 20—Other Functions Fast Meter Fall Time: When this preference is on, the level meters fall quicker. TC Drop Warning: When this preference is on, a warning message appears if a dropout is detected in the incoming timecode. DIO Warning: When this preference is on, a warning message appears if any errors are detected in digital audio signals received by the Slot Inputs or 2TR Digital Inputs.
PAGE 212
Setting Preferences 199 Preferences 3 1 Use the DISPLAY ACCESS [SETUP] button to locate the Preferences 3 page. 2 Use the cursor buttons or Parameter wheel to select the preferences, and use the INC/DEC buttons or [ENTER] button to set them. Mix Update Confirmation: When this preference is on, a confirmation message asking if you want to update the current Automix with the latest edits appears when Automix recording is stopped.
PAGE 213
200 Chapter 20—Other Functions Using the Oscillator 1 2 The 02R96 features an oscillator that can be used for calibration or diagnostic purposes. Use the DISPLAY ACCESS [UTILITY] button to locate the Oscillator page. Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC button, or [ENTER] button to set them. OSCILLATOR ON: This turns the Oscillator on or off. While the LEVEL parameter is selected, the [ENTER] button can be used to turn on and off the Oscillator.
PAGE 214
Initializing the 02R96 201 Initializing the 02R96 The 02R96 can be initialized as follows. Warning: This procedure will clear all user memories and reset all settings to their initial values. You may want to back up any important data beforehand via MIDI Bulk Dump (see page 168). If you want to reset just the mix settings, recall scene memory #0 instead (see page 139). 1 Turn off the 02R96. 2 While holding down the SCENE MEMORY [STORE] button, turn on the 02R96.
PAGE 215
202 Appendix A: Parameter Lists Appendix A: Parameter Lists USER DEFINED KEYS # Function # Display 0 No ASSIGN No Assign 1 Scene MEM. Recall +1 Scene +1 Recall 2 Scene MEM. Recall –1 Scene –1 Recall 3 Scene MEM. Recall No. XX Scene XX Recall 4 Effect-1 Lib. Recall +1 Fx1 Lib+1 Recall 5 Effect-1 Lib. Recall –1 Fx1 Lib –1 Recall 6 Effect-1 Lib. Recall No. XX Fx1 LibXXX RCL. 7 Effect-2 Lib. Recall +1 Fx2 Lib+1 Recall 8 Effect-2 Lib. Recall –1 Fx2 Lib–1 Recall 9 Effect-2 Lib.
PAGE 216
USER DEFINED KEYS # Function 203 Display 92 Overwrite EQ Overwrite EQ 93 Overwrite AUX Overwrite AUX 94 Overwrite AUX ON Overwrite AUX ON 95 Track Arming 1 ON/OFF Track Arming 1 96 Track Arming 2 ON/OFF Track Arming 2 97 Track Arming 3 ON/OFF Track Arming 3 98 Track Arming 4 ON/OFF Track Arming 4 99 Track Arming 5 ON/OFF Track Arming 5 100 Track Arming 6 ON/OFF Track Arming 6 101 Track Arming 7 ON/OFF Track Arming 7 102 Track Arming 8 ON/OFF Track Arming 8 103 Track Ar
PAGE 217
204 Appendix A: Parameter Lists USER DEFINED KEYS Initial Assignments # Bank A Bank B Bank C Bank D 1 Surr Lib 0 Recall Scene 1 Recall IN Fader Group A Automix ENABLE 2 Surr Lib –1 Recall Scene 2 Recall IN Fader Group B Automix REC 3 Surr Lib +1 Recall Scene 3 Recall IN Fader Group C Automix ABORT 4 No Assign Scene 4 Recall IN Fader Group D Automix AUTOREC 5 No Assign Scene 5 Recall IN Fader Group E Automix RETURN 6 Surr.
PAGE 218
Input Patch Parameters Input Channel Inputs Port ID Input Channel insert Ins Description Port ID Description 205 Internal Effects Processor Inputs Port ID Description S1-4 Slot1 CH4 IN S1-4 Slot1 CH4 IN INSCH20 InsertOut-CH20 S1-5 Slot1 CH5 IN S1-5 Slot1 CH5 IN INSCH21 InsertOut-CH21 S1-6 Slot1 CH6 IN S1-6 Slot1 CH6 IN INSCH22 InsertOut-CH22 S1-7 Slot1 CH7 IN S1-7 Slot1 CH7 IN INSCH23 InsertOut-CH23 S1-8 Slot1 CH8 IN S1-8 Slot1 CH8 IN INSCH24 InsertOut-CH24 S1-9 Slot1
PAGE 219
206 Appendix A: Parameter Lists Input Channel Inputs Port ID Input Channel insert Ins Description Port ID Description Internal Effects Processor Inputs Port ID Description S4-7 Slot4 CH7 IN S4-7 Slot4 CH7 IN INSAUX7 InsertOut-AUX7 S4-8 Slot4 CH8 IN S4-8 Slot4 CH8 IN INSAUX8 InsertOut-AUX8 S4-9 Slot4 CH9 IN S4-9 Slot4 CH9 IN INSSTL InsertOut-STL S4-10 Slot4 CH10 IN S4-10 Slot4 CH10 IN INSSTR InsertOut-STR S4-11 Slot4 CH11 IN S4-11 Slot4 CH11 IN FX1-1 Effect1 OUT 1 S4-12
PAGE 220
Initial Input Patch Settings 207 Initial Input Patch Settings Input channel Inputs # Source # Source 1 AD01 29 S1-05 2 AD02 30 S1-06 3 AD03 31 S1-07 4 AD04 32 S1-08 5 AD05 33 S2-01 6 AD06 34 S2-02 7 AD07 35 S2-03 8 AD08 36 S2-04 9 AD09 37 S2-05 10 AD10 38 S2-06 11 AD11 39 S2-07 12 AD12 40 S2-08 13 AD13 41 S3-01 14 AD14 42 S3-02 15 AD15 43 S3-03 16 AD16 44 S3-04 17 AD17 45 S3-05 18 AD18 46 S3-06 19 AD19 47 S3-07 20 AD20 48 S
PAGE 221
208 Appendix A: Parameter Lists Output Patch Parameters Output patch parameters are split into two tables. The first table contains parameters for the Slot Outputs, Omni Outs, and Output Channel Insert Ins. The second table, Direct Outs and, 2TR Digital Outputs.
PAGE 222
Output Patch Parameters Slot Outputs Source Description Omni Outs Source 209 Output Channel Insert Ins Description Source Description INSCH26 InsertOut-CH26 INSCH26 InsertOut-CH26 S2-4 Slot2 CH4 IN INSCH27 InsertOut-CH27 INSCH27 InsertOut-CH27 S2-5 Slot2 CH5 IN INSCH28 InsertOut-CH28 INSCH28 InsertOut-CH28 S2-6 Slot2 CH6 IN INSCH29 InsertOut-CH29 INSCH29 InsertOut-CH29 S2-7 Slot2 CH7 IN INSCH30 InsertOut-CH30 INSCH30 InsertOut-CH30 S2-8 Slot2 CH8 IN INSCH31 InsertOut-
PAGE 223
210 Appendix A: Parameter Lists Slot Outputs Source Description Omni Outs Source Description Output Channel Insert Ins Source Description Surr Ls Surround Monitor Ls Surr Ls Surround Monitor Ls FX1-7 Effect1 OUT 7 Surr Rs Surround Monitor Rs Surr Rs Surround Monitor Rs FX1-8 Effect1 OUT 8 Surr C Surround Monitor C Surr C Surround Monitor C FX2-1 Effect2 OUT 1 Surr LFE Surround Monitor LFE Surr LFE Surround Monitor LFE FX2-2 Effect2 OUT 2 Surr Ls2 Surround Monitor Ls2 Surr L
PAGE 224
Output Patch Parameters 211 Output Patch Table 2 Direct Outs Source 2TR Digital Outs Description Source Description NONE NONE NONE NONE S1-1 Slot1 CH1 OUT BUS1 BUS1 S1-2 Slot1 CH2 OUT BUS2 BUS2 S1-3 Slot1 CH3 OUT BUS3 BUS3 S1-4 Slot1 CH4 OUT BUS4 BUS4 S1-5 Slot1 CH5 OUT BUS5 BUS5 S1-6 Slot1 CH6 OUT BUS6 BUS6 S1-7 Slot1 CH7 OUT BUS7 BUS7 S1-8 Slot1 CH8 OUT BUS8 BUS8 S1-9 Slot1 CH9 OUT AUX1 AUX1 S1-10 Slot1 CH10 OUT AUX2 AUX2 S1-11 Slot1 CH11 OUT AUX3 AUX3
PAGE 225
212 Appendix A: Parameter Lists Direct Outs Source 2TR Digital Outs Description Source Description S4-2 Slot4 CH2 OUT INSCH32 InsertOut-CH32 S4-3 Slot4 CH3 OUT INSCH33 InsertOut-CH33 S4-4 Slot4 CH4 OUT INSCH34 InsertOut-CH34 S4-5 Slot4 CH5 OUT INSCH35 InsertOut-CH35 S4-6 Slot4 CH6 OUT INSCH36 InsertOut-CH36 S4-7 Slot4 CH7 OUT INSCH37 InsertOut-CH37 S4-8 Slot4 CH8 OUT INSCH38 InsertOut-CH38 S4-9 Slot4 CH9 OUT INSCH39 InsertOut-CH39 S4-10 Slot4 CH10 OUT INSCH40 InsertO
PAGE 226
Initial Output Patch Settings Initial Output Patch Settings Slot Outputs # Source # Source SLOT4-02 BUS2 SLOT4-03 BUS3 SLOT4-04 BUS4 SLOT4-05 BUS5 SLOT1-01 BUS1 SLOT4-06 BUS6 SLOT1-02 BUS2 SLOT4-07 BUS7 SLOT1-03 BUS3 SLOT4-08 BUS8 SLOT1-04 BUS4 SLOT4-09 BUS1 SLOT1-05 BUS5 SLOT4-10 BUS2 SLOT1-06 BUS6 SLOT4-11 BUS3 SLOT1-07 BUS7 SLOT4-12 BUS4 SLOT1-08 BUS8 SLOT4-13 BUS5 SLOT1-09 BUS1 SLOT4-14 BUS6 SLOT1-10 BUS2 SLOT4-15 BUS7 SLOT1-11 BUS3 SLOT4-16 BUS8
PAGE 227
214 Appendix A: Parameter Lists # Destination 23 SLOT3-07 24 SLOT3-08 25 SLOT4-01 Input Channel ID Short Name Long Name CH15 CH15 CH15 CH16 CH16 CH16 CH17 CH17 CH17 CH18 CH18 CH18 CH19 CH19 CH19 CH20 CH20 CH20 CH21 CH21 CH21 CH22 CH22 CH22 CH23 CH23 CH23 CH24 CH24 CH24 26 SLOT4-02 27 SLOT4-03 28 SLOT4-04 29 SLOT4-05 30 SLOT4-06 31 SLOT4-07 32 SLOT4-08 33 NONE CH25 CH25 CH25 34 NONE CH26 CH26 CH26 35 NONE CH27 CH27 CH27 36 NONE CH28 C
PAGE 228
Initial Input Port Names Output Channel ID Short Name Long Name Port PORT ID Short Name Long Name 215 BUS6 BUS6 BUS6 SLOT1-12 S1-12 S112 Slot1 CH12 IN BUS7 BUS7 BUS7 SLOT1-13 S1-13 S113 Slot1 CH13 IN BUS8 BUS8 BUS8 SLOT1-14 S1-14 S114 Slot1 CH14 IN AUX1 AUX1 AUX1 SLOT1-15 S1-15 S115 Slot1 CH15 IN AUX2 AUX2 AUX2 SLOT1-16 S1-16 S116 Slot1 CH16 IN AUX3 AUX3 AUX3 SLOT2-01 S2-01 S201 Slot2 CH1 IN AUX4 AUX4 AUX4 SLOT2-02 S2-02 S202 Slot2 CH2 IN AUX5 AUX5
PAGE 229
216 Appendix A: Parameter Lists Port PORT ID Short Name Long Name SLOT4-15 S4-15 S415 Slot4 CH15 IN SLOT4-16 S4-16 S416 Slot4 CH16 IN 2TD1L 2TD1L 2D1L 2TR IN Dig.1 L 2TD1R 2TD1R 2D1R 2TR IN Dig.1 R 2TD2L 2TD2L 2D2L 2TR IN Dig.2 L 2TD2R 2TD2R 2D2R 2TR IN Dig.2 R 2TD3L 2TD3L 2D3L 2TR IN Dig.3 L 2TD3R 2TD3R 2D3R 2TR IN Dig.
PAGE 230
GPI Trigger Source List GPI Trigger Source List # Source 0 NO ASSIGN 1 2 CH1 FADER ON CH2 FADER ON 3 CH3 FADER ON 4 CH4 FADER ON 5 6 7 8 9 10 CH5 FADER ON CH6 FADER ON CH7 FADER ON CH8 FADER ON CH9 FADER ON CH10 FADER ON 11 CH11 FADER ON 12 CH12 FADER ON 13 14 15 16 17 18 CH13 FADER ON CH14 FADER ON CH15 FADER ON CH16 FADER ON CH17 FADER ON CH18 FADER ON 19 CH19 FADER ON 20 CH20 FADER ON 21 22 23 24 25 26 CH21 FADER ON CH22 FADER ON CH23 FADER ON CH24 FADER ON CH25 FADER ON CH26 FADE
PAGE 231
218 # Appendix A: Parameter Lists Source # Source 108 CH35 FADER OFF 163 UDEF1 UNLATCH 109 CH36 FADER OFF 164 UDEF2 UNLATCH 110 CH37 FADER OFF 165 UDEF3 UNLATCH 111 CH38 FADER OFF 166 UDEF4 UNLATCH 112 CH39 FADER OFF 167 UDEF5 UNLATCH 113 CH40 FADER OFF 168 UDEF6 UNLATCH 114 CH41 FADER OFF 169 UDEF7 UNLATCH 115 CH42 FADER OFF 170 UDEF8 UNLATCH 116 CH43 FADER OFF 171 UDEF9 UNLATCH 117 CH44 FADER OFF 172 UDEF10 UNLATCH 118 CH45 FADER OFF 173 UDEF11 UNLATCH 119
PAGE 232
User Defined Remote Layer Initial Bank Settings 219 User Defined Remote Layer Initial Bank Settings Bank 1 (GM Vol & Pan) ID Short Name Long RM01 GM01 GM-CH01 VOL&PAN RM02 GM02 GM-CH02 VOL&PAN RM03 GM03 GM-CH03 VOL&PAN RM04 GM04 GM-CH04 VOL&PAN RM05 GM05 GM-CH05 VOL&PAN RM06 GM06 GM-CH06 VOL&PAN RM07 GM07 GM-CH07 VOL&PAN RM08 GM08 GM-CH08 VOL&PAN RM09 GM09 GM-CH09 VOL&PAN RM10 GM10 GM-CH10 VOL&PAN RM11 GM11 GM-CH11 VOL&PAN RM12 GM12 GM-CH12 VOL&PAN RM13 GM13 GM-CH13 VOL&PAN RM
PAGE 233
220 Appendix A: Parameter Lists Bank 2 (GM Vol & Effect 1) ID Short Name Long RM01 GM01 GM-CH01 VOL&EFF1 RM02 GM02 GM-CH02 VOL&EFF1 RM03 GM03 GM-CH03 VOL&EFF1 RM04 GM04 GM-CH04 VOL&EFF1 RM05 GM05 GM-CH05 VOL&EFF1 RM06 GM06 GM-CH06 VOL&EFF1 RM07 GM07 GM-CH07 VOL&EFF1 RM08 GM08 GM-CH08 VOL&EFF1 RM09 GM09 GM-CH09 VOL&EFF1 RM10 GM10 GM-CH10 VOL&EFF1 RM11 GM11 GM-CH11 VOL&EFF1 RM12 GM12 GM-CH12 VOL&EFF1 RM13 GM13 GM-CH13 VOL&EFF1 RM14 GM14 GM-CH14 VOL&EFF1 RM15 GM15 GM-CH15 VOL&
PAGE 234
User Defined Remote Layer Initial Bank Settings 221 Bank 3 (XG Vol & Pan) ID Short Name Long RM01 XG01 XG-CH01 VOL&PAN RM02 XG02 XG-CH02 VOL&PAN RM03 XG03 XG-CH03 VOL&PAN RM04 XG04 XG-CH04 VOL&PAN RM05 XG05 XG-CH05 VOL&PAN RM06 XG06 XG-CH06 VOL&PAN RM07 XG07 XG-CH07 VOL&PAN RM08 XG08 XG-CH08 VOL&PAN RM09 XG09 XG-CH09 VOL&PAN RM10 XG10 XG-CH10 VOL&PAN RM11 XG11 XG-CH11 VOL&PAN RM12 XG12 XG-CH12 VOL&PAN RM13 XG13 XG-CH13 VOL&PAN RM14 XG14 XG-CH14 VOL&PAN RM15 XG15 XG-CH15 VOL
PAGE 235
222 Appendix A: Parameter Lists Bank 4 (Nuendo VST Mixer) ID Short Name Long RM01 CH1 VST MIXER CH1 RM02 CH2 VST MIXER CH2 RM03 CH3 VST MIXER CH3 RM04 CH4 VST MIXER CH4 RM05 CH5 VST MIXER CH5 RM06 CH6 VST MIXER CH6 RM07 CH7 VST MIXER CH7 RM08 CH8 VST MIXER CH8 RM09 CH9 VST MIXER CH9 RM10 CH10 VST MIXER CH10 RM11 CH11 VST MIXER CH11 RM12 CH12 VST MIXER CH12 RM13 CH13 VST MIXER CH13 RM14 CH14 VST MIXER CH14 RM15 CH15 VST MIXER CH15 RM16 CH16 VST MIXER CH16 RM17 CH17 VST M
PAGE 236
Effects Parameters 223 Effects Parameters REVERB HALL, REVERB ROOM, REVERB STAGE, REVERB PLATE One input, two output hall, room, stage, and plate reverb simulations, all with gates. Parameter Range Description REV TIME 0.3–99.0 s Reverb time INI. DLY 0.0–500.0 ms Initial delay before reverb begins HI. RATIO 0.1–1.0 High-frequency reverb time ratio LO. RATIO 0.1–2.4 Low-frequency reverb time ratio DIFF. 0.0–1.
PAGE 237
224 Appendix A: Parameter Lists GATE REVERB, REVERSE GATE One input, two output early reflections with gate, and early reflections with reverse gate. Parameter Range Description TYPE Type-A, Type-B Type of early reflection simulation ROOMSIZE 0.1–20.0 Reflection spacing LIVENESS 0–10 Early reflections decay characteristics (0 = dead, 10 = live) INI. DLY 0.0–500.0 ms Initial delay before reverb begins DIFF.
PAGE 238
Effects Parameters 225 STEREO DELAY Two input, two output basic stereo delay. Parameter Range Description DELAY L 0.0–1350.0 ms Left channel delay time DELAY R 0.0–1350.0 ms Right channel delay time FB. G L –99 to +99% Left channel feedback (plus values for normal-phase feedback, minus values for reverse-phase feedback) FB. G R –99 to +99% Right channel feedback (plus values for normal-phase feedback, minus values for reverse-phase feedback) HI. RATIO 0.1–1.
PAGE 239
226 Appendix A: Parameter Lists DELAY LCR One input, two output 3-tap delay (left, center, right). Parameter Range 0.0–2730.0 ms Left channel delay time DELAY C 0.0–2730.0 ms Center channel delay time DELAY R 0.0–2730.0 ms Right channel delay time FB. DLY 0.0–2730.0 ms Feedback delay time LEVEL L –100 to +100% Left channel delay level LEVEL C –100 to +100% Center channel delay level LEVEL R –100 to +100% Right channel delay level FB.
PAGE 240
Effects Parameters 227 ECHO Two input, two output stereo delay with crossed feedback loop. Parameter Range Description DELAY L 0.0–1350.0 ms Left channel delay time DELAY R 0.0–1350.0 ms Right channel delay time FB. D L 0.0–1350.0 ms Left channel feedback delay time FB. D R 0.0–1350.0 ms Right channel feedback delay time FB. G L –99 to +99% Left channel feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) FB.
PAGE 241
228 Appendix A: Parameter Lists FLANGE Two input, two output flange effect. Parameter Range Description FREQ. 0.05–40.00 Hz Modulation speed DEPTH 0–100% Modulation depth MOD. DLY 0.0–500.0 ms Modulation delay time FB. GAIN –99 to +99% Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) WAVE Sine, Tri Modulation waveform LSH F 21.2 Hz–8.00 kHz Low shelving filter frequency LSH G –12 to +12 dB Low shelving filter gain EQ F 100 Hz–8.
PAGE 242
Effects Parameters 229 PHASER Two input, two output 16-stage phaser. Parameter Range Description FREQ. 0.05–40.00 Hz Modulation speed DEPTH 0–100% Modulation depth FB. GAIN –99 to +99% Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) OFFSET 0–100 Lowest phase-shifted frequency offset PHASE 0.00–354.38 degrees Left and right modulation phase balance STAGE 2, 4, 6, 8, 10, 12, 14, 16 Number of phase shift stages LSH F 21.2 Hz–8.
PAGE 243
230 Appendix A: Parameter Lists TREMOLO Two input, two output tremolo effect. Parameter Range Description FREQ. 0.05–40.00 Hz Modulation speed DEPTH 0–100% Modulation depth WAVE Sine, Tri, Square Modulation waveform LSH F 21.2 Hz–8.00 kHz Low shelving filter frequency LSH G –12 to +12 dB Low shelving filter gain EQ F 100 Hz–8.00 kHz EQ (peaking type) frequency EQ G –12 to +12 dB EQ (peaking type) gain EQ Q 10.0–0.10 EQ (peaking type) bandwidth HSH F 50.0 Hz–16.
PAGE 244
Effects Parameters 231 DUAL PITCH Two input, two output pitch shifter. Parameter Range Description PITCH 1 –24 to +24 semitones Channel #1 pitch shift FINE 1 –50 to +50 cents Channel #1 pitch shift fine LEVEL 1 –100 to +100% Channel #1 level (plus values for normal phase, minus values for reverse phase) PAN 1 L63 to R63 Channel #1 pan DELAY 1 0.0–1000.0 ms Channel #1 delay time FB.
PAGE 245
232 Appendix A: Parameter Lists RING MOD. Two input, two output ring modulator. Parameter Range SOURCE Description OSC, SELF Modulation source: oscillator or input signal OSC FREQ 0.0–5000.0 Hz Oscillator frequency FM FREQ 0.05–40.00 Hz Oscillator frequency modulation speed FM DEPTH 0–100% Oscillator frequency modulation depth SYNC OFF/ON Tempo parameter sync on/off NOTE FM 1 Used in conjunction with TEMPO to determine FM FREQ 1. MOD. FILTER Two input, two output modulation filter.
PAGE 246
Effects Parameters 233 AMP SIMULATE One input, two output guitar amp simulator. Parameter Range Description AMP TYPE 1 Guitar amp simulation type DST TYPE DST1, DST2, OVD1, OVD2, CRUNCH Distortion type (DST = distortion, OVD = overdrive) DRIVE 0–100 Distortion drive MASTER 0–100 Master volume BASS 0–100 Bass tone control MIDDLE 0–100 Middle tone control TREBLE 0–100 High tone control CAB DEP 0–100% Speaker cabinet simulation depth EQ F 99–8.
PAGE 247
234 Appendix A: Parameter Lists DYNA. FLANGE Two input, two output dynamically controlled flanger. Parameter Range Description SOURCE INPUT, MIDI Control source: input signal or MIDI Note On velocity SENSE 0–100 Sensitivity DIR. UP, DOWN Upward or downward frequency change DECAY 1 Decay speed OFFSET 0–100 Delay time offset FB GAIN –99 to +99% Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) LSH F 21.2 Hz–8.
PAGE 248
Effects Parameters 235 REV+CHORUS One input, two output reverb and chorus effects in parallel. Parameter Range Description INI. DLY 0.0–500.0 ms Initial delay before reverb begins REV TIME 0.3–99.0 s Reverb time HI. RATIO 0.1–1.0 High-frequency reverb time ratio DIFF. 0.1–1.0 Spread DENSITY 0–100% Reverb density HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency LPF 50.0 Hz–16.
PAGE 249
236 Appendix A: Parameter Lists REV+FLANGE One input, two output reverb and flanger effects in parallel. Parameter Range Description INI. DLY 0.0–500.0 ms Initial delay before reverb begins REV TIME 0.3–99.0 s Reverb time HI. RATIO 0.1–1.0 High-frequency reverb time ratio DIFF. 0.1–1.0 Spread DENSITY 0–100% Reverb density HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency LPF 50.0 Hz–16.
PAGE 250
Effects Parameters 237 REV+SYMPHO. One input, two output reverb and symphonic effects in parallel. Parameter Range Description INI. DLY 0.0–500.0 ms Initial delay before reverb begins REV TIME 0.3–99.0 s Reverb time HI. RATIO 0.1–1.0 High-frequency reverb time ratio DIFF. 0.1–1.0 Spread DENSITY 0–100% Reverb density HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency LPF 50.0 Hz–16.
PAGE 251
238 Appendix A: Parameter Lists REV->PAN One input, two output reverb and autopan effects in parallel. Parameter Range Description INI. DLY 0.0–500.0 ms Initial delay before reverb begins REV TIME 0.3–99.0 s Reverb time HI. RATIO 0.1–1.0 High-frequency reverb time ratio DIFF. 0.1–1.0 Spread DENSITY 0–100% Reverb density HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency LPF 50.0 Hz–16.0 kHz, THRU Low-pass filter cutoff frequency REV BAL.
PAGE 252
Effects Parameters 239 DELAY+ER. One input, two output delay and early reflections effects in parallel. Parameter Range Description DELAY L 0.0–1000.0 ms Left channel delay time DELAY R 0.0–1000.0 ms Right channel delay time FB. DLY 0.0–1000.0 ms Feedback delay time FB. GAIN –99 to +99% Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) HI. RATIO 0.1–1.0 High-frequency feedback ratio HPF THRU, 21.2 Hz–8.
PAGE 253
240 Appendix A: Parameter Lists DELAY->ER. One input, two output delay and early reflections effects in series. Parameter Range Description DELAY L 0.0–1000.0 ms Left channel delay time DELAY R 0.0–1000.0 ms Right channel delay time FB. DLY 0.0–1000.0 ms Feedback delay time FB. GAIN –99 to +99% Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) HI. RATIO 0.1–1.0 High-frequency feedback ratio HPF THRU, 21.2 Hz–8.
PAGE 254
Effects Parameters 241 DELAY+REV One input, two output delay and reverb effects in parallel. Parameter Range Description DELAY L 0.0–1000.0 ms Left channel delay time DELAY R 0.0–1000.0 ms Right channel delay time FB. DLY 0.0–1000.0 ms Feedback delay time FB. GAIN –99 to +99% Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) DELAY HI 0.1–1.0 Delay high-frequency feedback ratio HPF THRU, 21.2 Hz–8.
PAGE 255
242 Appendix A: Parameter Lists DELAY->REV One input, two output delay and reverb effects in series. Parameter Range Description DELAY L 0.0–1000.0 ms Left channel delay time DELAY R 0.0–1000.0 ms Right channel delay time FB. DLY 0.0–1000.0 ms Feedback delay time FB. GAIN –99 to +99% Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) DELAY HI 0.1–1.0 Delay high-frequency feedback ratio HPF THRU, 21.2 Hz–8.
PAGE 256
Effects Parameters 243 DIST->DELAY One input, two output distortion and delay effects in series. Parameter Range Description DST TYPE DST1, DST2, OVD1, OVD2, CRUNCH Distortion type (DST = distortion, OVD = overdrive) DRIVE 0–100 Distortion drive MASTER 0–100 Master volume TONE –10 to +10 Tone control N. GATE 0–20 Noise reduction DELAY 0.0–2725.0 ms Delay time FB. GAIN –99 to +99% Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) HI.
PAGE 257
244 Appendix A: Parameter Lists FREEZE One input, one output basic sampler. Parameter Range Description REC MODE MANUAL, INPUT In MANUAL mode, recording is started by pressing the REC and PLAY buttons. In INPUT mode, Record-Ready mode is engaged by pressing the REC button, and actual recording is triggered by the input signal. REC DLY –1000 to +1000 ms Recording delay. For plus values, recording starts after the trigger is received.
PAGE 258
Effects Parameters 245 REVERB 5.1 One input, six output reverb for 5.1 surround, with surround panning. Parameter Range Description REV TIME 0.3–99.0 s Reverb time REV TYPE Hall, Room, Stage, Plate Reverb type HI. RATIO 0.1–1.0 High-frequency reverb time ratio DIFF. 0.0–1.0 Reverb diffusion (left–right reverb spread) DENSITY 0–100% Reverb density HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency LPF 50.0 Hz–16.0 kHz, THRU Low-pass filter cutoff frequency DIV.
PAGE 259
246 Appendix A: Parameter Lists AUTO PAN 5.1 Six input, six output autopanner for 5.1 surround. You can reset to the pan position specified by the OFFSET parameter by pressing the RESET button. Parameter Range Description SOURCE OFF, HOLD, INPUT, MIDI When set to OFF, the TRIGGER button is used to start autopan. When set to HOLD, autopan runs continuously. When set to INPUT, the input signal triggers autopan. When set to MIDI, a MIDI Note On message can be used to trigger autopan. TRIG.
PAGE 260
Effects Parameters 247 FLANGE 5.1 Six input, six output flanger for 5.1 surround. Parameter Range Description FREQ. 0.05–40.00 Hz Modulation speed DEPTH 0–100% Modulation depth MOD. DLY 0.0–400.0 ms Modulation delay time FB. GAIN –99 to +99% Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) WAVE Sine, Tri Modulation waveform HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency LPF 50.0 Hz–16.
PAGE 261
248 Appendix A: Parameter Lists M. BAND DYNA. Two input, two output 3-band dynamics processor, with individual solo and gain reduction metering for each band. Parameter Range Description LOW GAIN –96.0 to +12.0 dB Low band level MID GAIN –96.0 to +12.0 dB Mid band level HI. GAIN –96.0 to +12.0 dB High band level PRESENCE –10 to +10 For positive values, the threshold of the high band is lowered and the threshold of the low band is increased. For negative values, the opposite will occur.
PAGE 262
Effects Parameters 249 COMP 5.1 Six input, six output compressor for 5.1 surround, with individual solo for each band, and gain reduction metering of left and right (L+R), left surround and right surround (LS+RS), center (C), or LFE channels. Parameter Range Description LOW GAIN –96.0 to +12.0 dB Low band level MID GAIN –96.0 to +12.0 dB Mid band level HI. GAIN –96.0 to +12.
PAGE 263
250 Appendix A: Parameter Lists COMPAND 5.1 Six input, six output compander for 5.1 surround, with individual solo for each band, and gain reduction metering of left and right (L+R), left surround and right surround (LS+RS), center (C), or LFE channels. Parameter Range Description LOW GAIN –96.0 to +12.0 dB Low band level MID GAIN –96.0 to +12.0 dB Mid band level HI. GAIN –96.0 to +12.
PAGE 264
251 Preset EQ Parameters Preset EQ Parameters # 01 02 03 04 05 06 07 08 09 10 Parameter Title Bass Drum 1 Bass Drum 2 Snare Drum 1 Snare Drum 2 Tom-tom 1 Cymbal High Hat Percussion E. Bass 1 E. Bass 2 LOW L-MID H-MID HIGH PEAKING PEAKING PEAKING H.SHELF G +3.5 dB –3.5 dB 0.0 dB +4.0 dB F 100 Hz 265 Hz 1.06 kHz 5.30 kHz Q 1.2 10 0.9 — PEAKING PEAKING PEAKING LPF G +8.0 dB –7.0 dB +6.0 dB ON F 80 Hz 400 Hz 2.50 kHz 12.5 kHz Q 1.4 4.5 2.
PAGE 265
252 # 11 12 13 14 15 16 17 18 19 20 21 Appendix A: Parameter Lists Parameter Title Syn. Bass 1 Syn. Bass 2 Piano 1 Piano 2 E. G. Clean E. G. Crunch 1 E. G. Crunch 2 E. G. Dist. 1 E. G. Dist. 2 A. G. Stroke 1 A. G. Stroke 2 02R96—Owner’s Manual LOW L-MID H-MID HIGH PEAKING PEAKING PEAKING H.SHELF G +3.5 dB +8.5 dB 0.0 dB 0.0 dB F 85 Hz 950 Hz 4.00 kHz 12.5 kHz Q 0.1 8 4.5 — PEAKING PEAKING PEAKING H.SHELF G +2.5 dB 0.0 dB +1.5 dB 0.
PAGE 266
253 Preset EQ Parameters # 22 23 24 25 26 27 28 29 30 31 32 Parameter Title A. G. Arpeg. 1 A. G. Arpeg. 2 Brass Sec. Male Vocal 1 Male Vocal 2 Female Vo. 1 Female Vo. 2 Chorus & Harmo Total EQ 1 Total EQ 2 Total EQ 3 LOW L-MID H-MID HIGH L.SHELF PEAKING PEAKING PEAKING G –0.5 dB 0.0 dB 0.0 dB +2.0 dB F 224 Hz 1.00 kHz 4.00 kHz 6.70 kHz Q — 4.5 4.5 0.12 L.SHELF PEAKING PEAKING H.SHELF G 0.0 dB –5.5 dB 0.0 dB +4.0 dB F 180 Hz 355 Hz 4.00 kHz 4.
PAGE 267
254 # 33 34 35 36 37 38 39 40 Appendix A: Parameter Lists Parameter Title Bass Drum 3 Snare Drum 3 Tom-tom 2 Piano 3 Piano Low Piano High Fine-EQ Cass Narrator 02R96—Owner’s Manual LOW L-MID H-MID HIGH PEAKING PEAKING PEAKING PEAKING G +3.5 dB –10.0 dB +3.5 dB 0.0 dB F 118 Hz 315 Hz 4.25 kHz 20.0 kHz Q 2 10 0.4 0.4 L.SHELF PEAKING PEAKING PEAKING G 0.0 dB +2.0 dB +3.5 dB 0.0 dB F 224 Hz 560 Hz 4.25 kHz 4.00 kHz Q — 4.5 2.8 0.1 L.
PAGE 268
255 Preset Gate Parameters (fs = 44.1 kHz) Preset Gate Parameters (fs = 44.1 kHz) # 1 2 3 4 Title Gate Ducking A. Dr. BD A. Dr. SN Type GATE DUCKING GATE GATE Parameter Value Threshold (dB) –26 Range (dB) –56 Attack (ms) 0 Hold (ms) 2.56 Decay (ms) 331 Threshold (dB) –19 Range (dB) –22 Attack (ms) 93 Hold (ms) 1.20 S Decay (ms) 6.32 S Threshold (dB) –11 Range (dB) –53 Attack (ms) 0 Hold (ms) 1.
PAGE 269
256 # Appendix A: Parameter Lists Title Type Parameter Threshold (dB) 5 6 A. Dr. BD A. Dr. BD COMP COMPAND-H A. Dr. SN COMP 3 Attack (ms) 9 Out gain (dB) A. Dr. SN EXPAND 2 Release (ms) 58 Threshold (dB) –11 Ratio ( :1) 3.5 Attack (ms) Out gain (dB) COMPAND-S Threshold (dB) –17 Ratio ( :1) 2.5 Attack (ms) Out gain (dB) A. Dr. Tom EXPAND 2 Release (ms) 12 Threshold (dB) –23 Attack (ms) Out gain (dB) A. Dr. OverTop COMPAND-S E. B. Finger COMP 2 151 –8 1.
PAGE 270
257 Preset Compressor Parameters (fs = 44.1 kHz) # 13 14 15 16 Title E. B. Slap Syn. Bass Piano1 Piano2 Type COMP COMP COMP COMP Parameter Threshold (dB) –12 Ratio ( :1) 1.7 Attack (ms) 4.0 Knee hard Release (ms) 133 Threshold (dB) –10 Ratio ( :1) 3.5 Attack (ms) COMP 3.0 Knee hard Release (ms) 250 Threshold (dB) –9 Ratio ( :1) 2.5 Attack (ms) 17 Out gain (dB) 1.0 Knee hard Release (ms) 238 Threshold (dB) –18 Ratio ( :1) 3.5 Attack (ms) Out gain (dB) A.
PAGE 271
258 # 21 Appendix A: Parameter Lists Title Strings3 Type COMP Parameter Threshold (dB) –17 Ratio ( :1) 1.5 Attack (ms) 76 Out gain (dB) 2.5 Knee 22 BrassSection COMP Syn. Pad COMP 186 Threshold (dB) –18 Ratio ( :1) 1.7 Attack (ms) 18 Out gain (dB) 4.0 25 SamplingPerc Sampling BD COMPAND-S COMP 226 Threshold (dB) –13 Ratio ( :1) 2 Attack (ms) 58 Out gain (dB) 2.
PAGE 272
259 Preset Compressor Parameters (fs = 44.1 kHz) # 29 Title Solo Vocal2 Type COMP Parameter Threshold (dB) –8 Ratio ( :1) 2.5 Attack (ms) 26 Out gain (dB) 1.5 Knee Release (ms) 30 Chorus COMP Click Erase EXPAND –9 Ratio ( :1) 1.7 Attack (ms) 39 Out gain (dB) 2.5 Announcer COMPAND-H 226 Threshold (dB) –33 Ratio ( :1) 2 Attack (ms) 1 Out gain (dB) Limiter1 COMPAND-S Threshold (dB) –14 Ratio ( :1) 2.
PAGE 273
260 Appendix B: Specifications Appendix B: Specifications General Spec Number of scene memories 99 Internal Sampling Frequency External Normal rate: 44.1 kHz–10% to 48 kHz+6% Double rate: 88.2 kHz–10% to 96 kHz+6% Less than 2.0 ms CH INPUT to STEREO OUT (fs=48 kHz) Signal Delay Less than 1.
PAGE 274
General Spec 261 Option Input (SLOT 1–4) Available cards Optional digital interface cards (MY8, MY4 series) Digital Input (2TR IN DIGITAL 1–3) SRC On/off (1:3 and 3:1 maximum input to output sample rate ratio) Input patch — Phase Gate-type3 Normal/reverse On/off Key in: 12 ch Group (1–12, 13–24, 25–36, 37–48, 49–56)/AUX1–8 On/off Comp-type4 Key in: self /Stereo Link Pre EQ/pre fader/post fader Attenuator EQ –96.0 to +12.0 dB (0.
PAGE 275
262 Appendix B: Specifications Dither 2TR OUT DIGITAL 1–3 Option Output (SLOT 1–4) On/off Word length 16, 20, 24-bit Output patch STEREO, BUS1–8, AUX 1–8, DIRECT OUT 1–56, INSERT OUT, CONTROL ROOM Available card Optional digital interface card (MY8, MY4 series) Output patch SURROUND MONITOR, STEREO, BUS1–8, AUX1–8, DIRECT OUT 1–56, INSERT OUT (CH1–56, BUS1–8, AUX1–8, STEREO) Dither Comp-type4 Attenuator EQ On/off Word length 16/20/24-bit On/off Pre EQ/pre fader/post fader –96.0 to +12.0 dB (0.
PAGE 276
General Spec SURROUND MONITOR Mute On/off Solo On/off Source BUS1–8, SLOT 1–4 Monitor to C-R On/off Oscillator Pink noise/500–2 kHz/1 kHz/50 Hz Monitor matrix 5.1→5.1, 5.1→3-1, 5.1→ST, 3.1→3.1, 3.1→ST Bass management 5 presets Monitor alignment ATT (–12.0 dB to 12 dB 0.1 dB step), Delay (0–30.0 msec 0.
PAGE 277
264 Appendix B: Specifications Gate Parameters Threshold –54 dB to 0 dB (0.1 dB step) Range –70 dB to 0 dB (1 dB step) Attack 0 ms–120 ms (1 ms step) 0.02 ms–1.96 s (216 points) @ 48 kHz Gate Hold 0.02 ms–2.13 s (216 points) @ 44.1 kHz 0.01 ms–981 ms (216 points) @ 96 kHz 0.01 ms–1.06 s (216 points) @ 88.2 kHz 5 ms–42.3 s (160 points) @ 48 kHz Decay 6 ms–46.0 s (160 points) @ 44.1 kHz 3 ms–21.1 s (160 points) @ 96 kHz 3 ms–23.0 s (160 points) @ 88.2 kHz Threshold –54 dB to 0 dB (0.
PAGE 278
Controls Compander H Threshold –54 dB to 0 dB (0.1 dB step) Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points) Out gain –18 dB to 0 dB (0.1 dB step) Width 1 dB–90 dB (1 dB step) Attack 0 ms–120 ms (1 ms step) 265 5 ms–42.3 s (160 points) @ 48 kHz 6 ms–46.0 s (160 points) @ 44.1 kHz Release 3 ms–21.1 s (160 points) @ 96 kHz 3 ms–23.0 s (160 points) @ 88.2 kHz Compander S Threshold –54 dB to 0 dB (0.1 dB step) Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.
PAGE 279
266 Appendix B: Specifications DISPLAY button ROUTING 1, 2, 3, 4, 5, 6, 7, 8, STEREO, DIRECT, FOLLOW PAN buttons (w/LED) DISPLAY ACCESS PHASE/INSERT, DELAY buttons DISPLAY, GATE /COMP buttons DYNAMICS GATE ON, COMP ON buttons (w/LED) Parameter control x 5 DISPLAY button SELECTED CHANNEL Section PAN/SURROUND L, R, LINK, GRAB, EFFECT buttons (w/LED) Pan control Joystick (Sound image position control) DISPLAY button EQ ON button (w/LED) EQUALIZER GAIN controls: LOW, LOW-MID, HIGH-MID, HIGH FREQUENCY
PAGE 280
Indicators 267 Indicators Analog Section PEAK LED x24 INPUT 1–24 SIGNAL LED x24 INPUT 1–24 Digital Section DISPLAY CONTROL Section DISPLAY 320 × 240 dot graphic LCD (w/contrast control potentiometer) DYNAMICS GATE, COMP LEDs x2 PAN/SURROUND Pan position LEDs x10 SELECTED CHANNEL Section FREQUENCY, Q LEDs 2 × 4 dB, Hz, kHz 3 × 4 EQUALIZER 3-digit numeric LEDs x4 (parameter value) MONITOR Section SOLO LED x1 SCENE MEMORY section Scene memory number 2-digit numeric LED x1 Libraries Effe
PAGE 281
268 Appendix B: Specifications Analog Input Spec Input PAD GAIN –60 dB 0 INPUT A/B 1–16 –16 dB 26 INPUT 17–24 Actual Load Impedance –34 dB — +10 dB 3k Ω For Use With Nominal 50–600 Ω Mics & 600 Ω Lines 4K Ω 600 Ω Lines Input level Max. before clip Sensitivity1 Nominal –70 dB (0.245 mV) –60 dB (0.775 mV) –26 dB (38.8 mV) –16 dB (0.123 V) –2 dB (616 mV) 0 dB (775 mV) +10 dB (2.45 V) +24 dB (12.28 V) –44 dB (4.89 mV) –34 dB (15.5 mV) 0 dB (775 mV) +10 dB (2.45 V) +24 dB (12.
PAGE 282
Digital Input Spec 269 Digital Input Spec Input 2TR IN DIGITAL Format Data length Level 1 AES/EBU 24-bit RS422 2 IEC-60958 24-bit 0.5 Vpp/75 Ω Phono 3 IEC-60958 24-bit 0.5 Vpp/75 Ω Phono — — CASCADE IN RS422 Connector XLR-3-31 type (Balanced)1 D-SUB Half Pitch Connector 68P (Female) 1. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).
PAGE 283
270 Appendix B: Specifications I/O Slot Spec (1–4) Each I/O SLOT accepts a digital interface card. Only SLOT #1 has a serial interface.
PAGE 284
Connector Pin Assignments 271 Connector Pin Assignments CASCADE IN CASCADE OUT Pin Signal Pin Signal Pin Signal Pin Signal 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 GND INPUT 1-2(+) INPUT 3-4(+) INPUT 5-6(+) INPUT 7-8(+) INPUT 9-10(+) INPUT 11-12(+) INPUT 13-14(+) INPUT 15-16(+) DTR IN(+) RTS OUT(+) GND WORD CLOCK IN(+) WORD CLOCK OUT(+) CONTROL IN(+) CONTROL OUT(+) GND GND INPUT 17-18(+) INPUT 19-20(+) INPUT 21-22(+) INPUT 23-24(+) RESERVED RE
PAGE 285
239 mm PAD 02R96—Owner’s Manual PAN FADER ON 2 ON 1 5 0 5 10 15 20 30 40 50 5 10 15 20 30 40 50 2 26 50 SOLO SOLO 10 SEL 10 50 40 30 20 15 10 5 0 5 3 27 51 3 ON SOLO SEL AUTO 2 AUTO PLUG INS 1 0 AUX ASSIGN 1 10 50 40 30 20 15 10 5 0 5 4 28 52 4 ON SOLO SEL AUTO 3 CHANNEL INSERTS 10 50 40 30 20 15 10 5 0 5 5 29 53 5 ON SOLO SEL AUTO 4 ASSIGN 2 AUX 8 AUX 7 EFFECTS / PLUG INS SEL 1 25 49 AUX FADER MODE INTERNAL EFFECTS 5
PAGE 286
Scene Memory to Program Change Table 273 Appendix C: MIDI Scene Memory to Program Change Table Program Change # Initial Scene # 1 2 User Scene # Program Change # Initial Scene # 01 44 02 45 3 03 4 04 5 User Scene # Program Change# Initial Scene # 44 87 87 45 88 88 46 46 89 89 47 47 90 90 05 48 48 91 91 6 06 49 49 92 92 7 07 50 50 93 93 8 08 51 51 94 94 9 09 52 52 95 95 10 10 53 53 96 96 11 11 54 54 97 97 12 12 55 55 98 98 13 1
PAGE 287
274 Appendix C: MIDI Initial Parameter to Control Change Table # 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 High NO ASSIGN FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H FADER H NO ASSIGN F
PAGE 288
MIDI Data Format 275 MIDI Data Format 1. CHANNEL MESSAGE Command 8n NOTE OFF 9n NOTE ON Bn CONTROL CHANGE Cn PROGRAM CHANGE 4.2.2 PARAMETER CHANGE rx/tx rx rx rx/tx rx/tx function Control the internal effects Control the internal effects Control parameters Switch scene memories 2. SYSTEM COMMON MESSAGE Command F1 MIDI TIME CODE QUARTER FRAME F2 SONG POSITION POINTER rx/tx rx rx function Used when TIME REFERENCE is MIDI CLOCK. Used when TIME REFERENCE is MIDI CLOCK. 3.
PAGE 289
276 Appendix C: MIDI 8. CONTINUE (FB) If [TABLE] is selected STATUS DATA 1011nnnn Bn Control change 0ccccccc cc Control number (0-95, 102-119) 0vvvvvvv vv Control value (0-127) If [NRPN] is selected STATUS DATA STATUS DATA STATUS DATA STATUS DATA 1011nnnn 01100010 0vvvvvvv 1011nnnn 01100011 0vvvvvvv 1011nnnn 00100110 0vvvvvvv 1011nnnn 00000110 0vvvvvvv Bn 62 vv Bn 63 vv Bn 26 vv Bn 06 vv STATUS Control change 9.
PAGE 290
Format Details request. The data area is handled by converting seven words of 8-bit data into eight words of 7-bit data. [Conversion from actual data into bulk data] d[0~6]: actual data b[0~7]: bulk data b[0] = 0; for( I=0; I<7; I++){ if( d[I]&0x80){ b[0] |= 1<<(6-I); } b[I+1] = d[I]&0x7F; } [Restoration from bulk data into actual data] d[0~6]: actual data b[0~7]: bulk data for( I=0; I<7; I++){ b[0] <<= 1; d[I] = b[I+1]+(0x80&b[0]); } 12.2.
PAGE 291
278 Appendix C: MIDI 0bbbbbbb bb b=0-3(bank no.1-4) BLOCK INFO. 0ttttttt tt total block number(minimum number DATA is 0) 0bbbbbbb bb current block number(0-total block number) 0ddddddd ds User define layer CHECK SUM EOX : 0ddddddd 0eeeeeee 11110111 : de ee ee=(Invert('L'+...+de)+1)&0x7F F7 End of exclusive DATA NAME 01001101 00100000 00100000 00111000 01000011 00110101 00110100 01001001 00000000 0bbbbbbb 11110111 4D 20 20 38 43 35 34 49 00 bb F7 'M' '' '' '8' 'C' '5' '4' 'I' b=0-7(bank no.
PAGE 292
Format Details 12.2.11 Control change table bulk dump format STATUS ID No. SUB STATUS FORMAT No. COUNT HIGH COUNT LOW 11110000 01000011 0000nnnn 01111110 00000011 00010010 01001100 01001101 00100000 00100000 00111000 01000011 00110101 00110100 DATA NAME 01000011 00000000 00000000 BLOCK INFO. 0ttttttt DATA System exclusive message Manufacture's ID number (YAMAHA) n=0-15 (Device number=MIDI Channel) Universal bulk dump data count = ch * 128 + cl 'L' 'M' '' '' : '4' 'C' No.
PAGE 293
280 Appendix C: MIDI 00111000 01000011 00110101 00110100 DATA NAME 01010001 LIB. No. H 0bbbbbbb 38 43 35 34 51 bb '8' 'C' '5' '4' 'Q' 0-199(EQ Library no.1-200), 256-(channel current data) LIB. No. L 0bbbbbbb bb EOX 11110111 F7 End of exclusive 12.2.17 Compressor library bulk dump format The second and third bytes of the DATA NAME indicate the library number. 0:Library no.1 - 199:Library no.
PAGE 294
Format Details 00110100 34 '4' DATA NAME 01000100 45 'E' LIB. No. H 0bbbbbbb bh 0-127(Effect Library no.1-128), 256-259(Effect1-4 current) LIB. No. L 0bbbbbbb bl BLOCK INFO. 0ttttttt tt total block number(minimum number DATA is 0) 0bbbbbbb bb current block number(0-total block number) 0ddddddd ds Effect Library data CHECK SUM EOX : 0ddddddd 0eeeeeee 11110111 : de ee ee=(Invert('L'+...+de)+1)&0x7F F7 End of exclusive 12.2.
PAGE 295
282 Appendix C: MIDI 0bbbbbbb bh 0-32(Library no.0-32), 256(Current data) EOX 0bbbbbbb bl 11110111 F7 End of exclusive 12.2.29 Output patch library bulk dump format The second and third bytes of the DATA NAME indicate the library number. 0:Library no.0 - 32:Library no.32, 256:current output patch data For reception by the 02R96, only the user area is valid. (1-32, 256) STATUS ID No. SUB STATUS FORMAT No.
PAGE 296
Format Details CHECK SUM EOX 0ddddddd de 0eeeeeee ee ee=(Invert('L'+...+de)+1)&0x7F 11110111 F7 End of exclusive 12.2.34 Surround Monitor library bulk dump request format The second and third bytes of the DATA NAME indicate the library number. 0:Library no.0 - 32:Library no.32, 256:current data STATUS ID No. SUB STATUS FORMAT No.
PAGE 297
284 Appendix C: MIDI 12.3.4 Parameter request basic format (Universal format) STATUS ID No. SUB STATUS GROUP ID MODEL ID ADDRESS 11110000 01000011 0011nnnn 00111110 01111111 0ttttttt 0eeeeeee F0 43 3n 3E 7F tt ee System exclusive message n=0-15 (Device number=MIDI Channel) MODEL ID (digital mixer) Universal Data type DATA 0ccccccc cc Channel No. 11110111 F7 End of exclusive 12.3.5 Parameter Address Consult your dealer for parameter address details. 12.3.
PAGE 298
Format Details 12.3.12 Parameter change (Backup memory) Reception This is received if [Parameter change RX] is ON and the [Rx CH] matches the device number included in the SUB STATUS. This is echoed if [Parameter change ECHO] is ON. When this is received, the value of the specified parameter will be controlled. STATUS ID No.
PAGE 299
286 Appendix C: MIDI MODEL ID (digital mixer) Effect is 0:Effect 1–3:Effect 4 In the case of PAIR, you must specify channels for which pairing is possible. In the case of PAIR ON with COPY, you must specify Source Channel as the copy source, and Destination Channel as the copy destination. Universal 12.3.19 Parameter change (Function call Event: Effect) Function call Library Reception This is received if [Parameter change RX] is ON and the [Rx CH] matches the device number included in the SUB STATUS.
PAGE 300
Format Details change. STATUS ID No. SUB STATUS GROUP ID MODEL ID ADDRESS DATA EOX EOX 11110000 01000011 0001nnnn 00111110 00001011 00100001 0aaaaaaa 0aaaaaaa 0aaaaaaa 0ddddddd 0ddddddd : 11110111 F0 43 1n 3E 0B 21 aa aa aa dd dd System exclusive message Manufacture's ID number (YAMAHA) n=0-15 (Device number=MIDI Channel) MODEL ID (digital mixer) 02R96 Address UU Address UL Address LU Address LL Data1 H Data1 L F7 End of exclusive Meter data uses the unmodified DECAY value of the DSP.
PAGE 301
288 Appendix D: Options Appendix D: Options MB02R96 Peak Meter Bridge Installation 1 Unscrew the four fixing screws 1 on the 02R96 rear panel to which the meter bridge will be attached. 1 1 2 Using the four supplied 8 mm screws B, attach the brackets to the meter bridge, as shown below. 3 Align the meter bridge with the 02R96, and, using two of the supplied 12 mm screws C, screw in the top two fixing screws, but don’t tighten them fully. 4 Screw in the bottom two screws C and tighten them fully.
PAGE 302
MB02R96 Peak Meter Bridge 289 Meter Bridge Controls A Channel indicators These indicators show which channels are currently being metered: Input Channels 1–24, 25–48, or 49–56 and Aux Sends 1–8 and Bus Outs 1–8. 9 5 56 OVER 8 7 B INPUT METERING POSITION button & indicators This button is used to set the metering position for Input Channels to pre-EQ, pre-fader, or post-fader. It works in unison with the PRE EQ, PRE FADER, and POST FADER buttons for Input Channels on the Meter pages.
PAGE 303
290 Appendix D: Options SP02R96 Wooden Side Panels Attach the side panels as shown below.
PAGE 304
291 Index Symbols +48V ON/OFF switches 5 Numerics 1–24 button 15 25–48 button 15 2TR I/O channel status 48 dithering outputs 48 patching digital outputs 56 patching direct outs 56 patching inputs 52 sampling rate conversion 44 2TR IN ANALOG 1 +4 dB (BAL) 25 2TR IN ANALOG 2 –10 dBV (UNBAL) 25 2TR IN DIGITAL AES/EBU 1 27 2TR IN DIGITAL COAXIAL 2 & 3 27 2TR OUT DIGITAL AES/EBU 1 26 2TR OUT DIGITAL COAXIAL 2 & 3 26 2TR OUT DIGITAL OUT PATCH page 56 3-1 surround mode 69 5.1 surround mode 69 96 kHz, 88.
PAGE 305
292 BUS button 21 BUS FADER VIEW page 110 Bus outs attenuating 90 automix 145 bus to stereo library 126 channel library 123 compressors 97 delay 101 EQ 91 grouping faders 106 grouping mutes 107 inserts 95 level setting 77 metering 88 muting 77 naming 112 pairing 104 patching to 2TR digital outputs 56 patching to input channels 52 patching to omni outs 55 patching to slot outputs 54 routing to 66 routing to stereo out 78 scene recall safe 143 soloing 102 viewing fader settings 109 viewing parameter settings
PAGE 306
293 ROUTING 11 SCENE MEMORY 16 USER DEFINED KEYS 16 DIST->DELAY 243 DISTORTION 232 DITHER page 48 Dithering digital outputs 48 DIV (divergence) 71 Double channel 47 Double speed 47 DUAL PITCH 231 Ducking, input channels 60 Duplicating automix events 161 DYNA. FILTER 233 DYNA. FLANGE 234 DYNA. PHASER 234 Dynamic effects 132 DYNAMICS section about 12 compressors 98 gates 60 Dynamics. See Gates and Compressors E EARLY REF.
PAGE 307
294 output channel mutes 107 Guitar effects 132 H HIGH EQ 91 HIGHER SAMPLE RATE DATA TRANSFER FORMAT page 47 HIGH-MID EQ 91 HOLD control 12 Horizontal pairing 104 HQ.
PAGE 308
295 metering position 87 output channels 88 stereo out 89 METERING POSITION page 87 MIDI bulk dump 168 control change messages 167 data format 275 features 3 I/O ports 163 MIDI SETUP page 165 parameter change messages 167 port setup 164 ports 27 program change messages 166 supported messages 163 MIDI button 8 MIDI chapter 163 MIDI clock automix timecode source 152 Tap tempo, effects 134 MIDI SETUP page 165 MIDI Warning preference 198 MIDI/TO HOST SETUP page 164 mini YGDAI.
PAGE 309
296 PEAK indicators 5 Phantom power switches 5 Phase, input channel phase reverse 59 PHASE/INSERT button about 12 reversing phase 59 PHASER 229 Phone jacks 23 PHONES jack 19 PHONES LEVEL control 19 Phono connectors 23 Picture of control surface 4 PLAY button 17 PLAY button, automix 149 Playing back an automix 157 PLUG-IN EDIT page 136 PLUG-IN SETUP page 135 Plug-ins about 135 configuring 135 editing 136 MIDI port setup 164 storing via bulk dump 168 PLUG-INS button 9 Port ID/Port preference 198 Port IDs 57 P
PAGE 310
297 automix 145 cascading consoles 49 current scene display 29 edit buffer 138 edit indicator 138 fading scenes 142 memory #0 139 MIDI program changes 166 protecting 141 recalling 140 safe channels 143 sorting 144 storing 140 storing via bulk dump 168 undo memory 139 what’s stored 138 Scene memories chapter 138 SCENE MEMORY page 141 SCENE MEMORY section about 16 display 16 using 140 SCENE MEMORY SORT page 144 Scene up button 16 Scroll arrows, pages 30 SCRUB button 18 SEL buttons input channels 5 pairing cha
PAGE 311
298 AD inputs 121 dimmer level 121 mic 19 setup 121 using 121 TALKBACK button 22 TALKBACK LEVEL control 19 TALKBACK SETUP page 121 Tascam I/O card 45 TC Drop Warning preference 198 Tempo, effects 134 Terminating wordclocks 43 THRESHOLD control 12 TIME REFERENCE page 152 Time signature map, automix 153 TIME SIGNATURE page 153 Timecode automix source 152 capturing, automix 161 capturing, locate memories 194 capturing, setting memories 194 display 146 offset 146 Title edit window 32 Titling library memories 12
PAGE 312
02R96 Block Diagram (Gain Reduction) (Out Meter) INPUT 1(...56) SIGNAL GAIN METER (Out Meter) METER 0 26 INSERT I/O (1-16) METER (Gain Reduction) PAD B INSERT OFF GATE AD IN 1( ...16) AD Input 1-16 AD ON INSERT ATT 4BAND EQ Keyin 12ch Group(1-12,13-24....) AUX 1-8 INPUT DELAY PAN STEREO R Same as stereo master L (Gain Reduction) (Out Meter) LFE (Gain Reduction)(Out Meter) COMP METER METER PRE/POST ON AUX COMP AD IN 17( ..
PAGE 313
02R96 Level Diagram Analog Analog dBu +24 +20 Digital dBFS Bit 0 0 INSERT –20 –30 [+10dBu] 3 Nominal Input –10 5 INPUT PATCH PHASE GATE INSERT ATT. EQ INSERT COMP DELAY ON LEVEL INSERT PAN BUS Adder INSERT ATT. EQ INSERT COMP MASTER ON MASTER LEVEL INSERT BAL DELAY OUTPUT PATCH Analog Analog DA CASCADE IN CASCADE OUT Digital Clipping Level [+18dBu] 2 4 AD Digital dBu 1 +10 Max. Output [+18dBu] Nominal Output [+4dBu] [+4dBu] GAIN MIN.
PAGE 314
YAMAHA [Digital Mixing Console-Internal Parameters] Model: 02R96 Function... Date: 20 Mar. 2002 MIDI Implementation Chart Version: 1.
PAGE 315
YAMAHA CORPORATION V868730 R0 1 IP 320 02 04 830 AP Printed in Japan Pro Audio & Digital Musical Instrument Division P.O.