OWNER’S MANUAL XVS1100AWR(C) XVS1100ATR(C) YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2002.11-2.
EAU03438
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM EAU00002 INTRODUCTION Congratulations on your purchase of the Yamaha XVS1100AW(C)/XVS1100AT(C). This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM IMPORTANT MANUAL INFORMATION Particularly important information is distinguished in this manual by the following notations: The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Failure to follow WARNING instructions could result in severe injury or death to the motorcycle operator, a bystander or a person inspecting or repairing the motorcycle.
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM IMPORTANT MANUAL INFORMATION EW000000 WARNING PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLY AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE. DO NOT ATTEMPT TO OPERATE THIS MOTORCYCLE UNTIL YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES.
U5KS10.book Page 3 Tuesday, November 5, 2002 11:05 AM IMPORTANT MANUAL INFORMATION AFFIX DEALER LABEL HERE EAU04247 XVS1100AWR(C)/XVS1100ATR(C) OWNER’S MANUAL ©2002 by Yamaha Motor Corporation, U.S.A. 1st edition, November 2002 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in Japan.
U5KS10.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM SAFETY INFORMATION Safe riding .......................................................................................... 1-1 Protective apparel .............................................................................. 1-3 Modifications ...................................................................................... 1-3 Loading and accessories ................................................................... 1-3 Gasoline and exhaust gas....
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM SAFETY INFORMATION EAU03633 1- 1 MOTORCYCLES ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPENDENT UPON THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERATOR. EVERY OPERATOR SHOULD KNOW THE FOLLOWING REQUIREMENTS BEFORE RIDING THIS MOTORCYCLE. HE OR SHE SHOULD: 1. OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT SOURCE ON ALL ASPECTS OF MOTORCYCLE OPERATION. 2.
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM SAFETY INFORMATION 4. Many motorcycle accidents involve inexperienced operators. In fact, many operators who have been involved in accidents do not even have a current motorcycle license. a. Make sure that you are qualified and that you only lend your motorcycle to other qualified operators. b. Know your skills and limits. Staying within your limits may help you to avoid an accident. c.
U5KS10.book Page 3 Tuesday, November 5, 2002 11:05 AM SAFETY INFORMATION Protective apparel 1 The majority of fatalities from motorcycle accidents are the result of head injuries. The use of a safety helmet is the single most critical factor in the prevention or reduction of head injuries. 1. Always wear an approved helmet. 2. Wear a face shield or goggles. Wind in your unprotected eyes could contribute to an impairment of vision which could delay seeing a hazard. 3.
U5KS10.book Page 4 Tuesday, November 5, 2002 11:05 AM SAFETY INFORMATION Loading The total weight of the operator, passenger, accessories and cargo must not exceed the maximum load limit of 203 kg (448 lb). When loading within this weight limit, keep the following in mind: 1. Cargo and accessory weight should be kept as low and close to the motorcycle as possible. Make sure to distribute the weight as evenly as possible on both sides of the motorcycle to minimize imbalance or instability. 2.
U5KS10.book Page 5 Tuesday, November 5, 2002 11:05 AM SAFETY INFORMATION 1 a. Accessories fitted to the handlebar or the front fork area can create instability due to improper weight distribution or aerodynamic changes. If accessories are added to the handlebar or front fork area, they must be as lightweight as possible and should be kept to a minimum. b. Bulky or large accessories may seriously affect the stability of the motorcycle due to aerodynamic effects.
U5KS10.book Page 6 Tuesday, November 5, 2002 11:05 AM SAFETY INFORMATION a. The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. b. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. c. Do not park the motorcycle near a flammable source (e.g. a kerosene heater, or near an open flame), otherwise it could catch fire. 4.
U5KS10.book Page 7 Tuesday, November 5, 2002 11:05 AM SAFETY INFORMATION EAU02977 Location of important labels 1 Please read the following important labels carefully before operating this motorcycle.
U5KS10.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM DESCRIPTION Left view ............................................................................................. 2-1 Right view........................................................................................... 2-2 Controls and instruments ...................................................................
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM DESCRIPTION EAU00026 2- Left view 2 1. Shift pedal 2. Fuel cock 3. Shock absorber assembly spring preload adjusting ring 4. Helmet holder 5. Storage compartment 6. Owner’s tool kit 7. Fuse box 8.
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM DESCRIPTION Right view 2 9. Battery 10. Main fuse 11. Main switch/steering lock 12. Air filter element 13.
U5KS10.book Page 3 Tuesday, November 5, 2002 11:05 AM DESCRIPTION Controls and instruments 2 1. Clutch lever 2. Left handlebar switches 3. Starter (choke) lever 4. Speedometer unit 5. Fuel tank cap 6. Right handlebar switches 7. Throttle grip 8.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS Main switch/steering lock .................................................................. 3-1 Indicator and warning lights .............................................................. 3-2 Speedometer unit .............................................................................. 3-3 Handlebar switches ........................................................................... 3-3 Clutch lever ...................
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS EAU00027 3- 3 EAU00029 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU00032 ON All electrical systems are supplied with power, and the headlight, meter lighting, taillight and position lights come on, and the engine can be started. The key cannot be removed.
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. _ _ EAU00061 1. 2. 3. 4. 5. Neutral indicator light “ ” This indicator light comes on when the transmission is in the neutral position.
U5KS10.book Page 3 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS 3 1. “TRIP” button 2. Odometer/trip meter EAU03193 Speedometer unit The speedometer unit is equipped with a digital odometer and a tripmeter. The speedometer shows riding speed. The odometer shows the total distance traveled. The tripmeter shows the distance traveled since it was last set to zero. Pushing the “TRIP” button switches the display between the odometer mode “ODO” and the tripmeter mode “TRIP”.
U5KS10.book Page 4 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS EAU04218 Turn signal switch “ / ” To signal a right-hand turn, push this switch to “ ”. To signal a left-hand turn, push this switch to “ ”. When released, the switch returns to the center position. Since this model is equipped with a self-canceling system, the turn signal lights will self-cancel after the motorcycle has traveled both about 150 m (490 ft) and for approximately 15 seconds.
U5KS10.book Page 5 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS 3 1. Shift pedal 1. Brake lever 1. Brake pedal EAU01215 EAU00158 EAU00162 Shift pedal Brake lever Brake pedal The shift pedal is located on the left side of the engine and is used in combination with the clutch lever when shifting the gears of the 5-speed constant-mesh transmission equipped on this motorcycle. The brake lever is located at the right handlebar grip.
U5KS10.book Page 6 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS To install the fuel tank cap 1. Insert the fuel tank cap into the tank opening with the key inserted in the lock and with the “ ” mark facing forward. 2. Turn the key counterclockwise to the original position, remove it, and then close the lock cover. 1. 2. a. b. Fuel tank cap lock cover “ ” mark Unlock. Lock. NOTE: The fuel tank cap cannot be installed unless the key is in the lock.
U5KS10.book Page 7 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS EAU00185 CAUTION: Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts. _ _ EAU04265 3 Recommended fuel: UNLEADED GASOLINE ONLY Fuel tank capacity: Total amount: 17 L (3.74 Imp gal, 4.49 US gal) Reserve amount: 4.5 L (0.99 Imp gal, 1.19 US gal) 1. Fuel tank filler tube 2.
U5KS10.book Page 8 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS OFF: closed position ON: normal position RES: reserve position 3 1. Pointed end positioned over “OFF” EAU02969 Fuel cock The fuel cock supplies fuel from the tank to the carburetors while also filtering it. The fuel cock lever positions are explained as follows and shown in the illustrations. 1. Pointed end positioned over “ON” 1.
U5KS10.book Page 9 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS ECA00038 CAUTION: Do not use the starter (choke) for more than 3 minutes as the exhaust pipe may discolor from excessive heat. In addition, extended use of the starter (choke) will cause afterburning. If this occurs, turn off the starter (choke). _ 3 1. Starter (choke) lever “ ” _ 1.
U5KS10.book Page 10 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS 3 1. Projection 2. Seat holder To install the passenger seat Insert the projection on the front of the passenger seat into the holder as shown, place the seat in the original position, and then install the bolt. 1. Bolt Rider seat To remove the rider seat 1. Remove the passenger seat. 2. Remove the bolt, and then pull the rider seat up. 1. Projection (× 2) 2. Seat holder (× 2) To install the rider seat 1.
U5KS10.book Page 11 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS 3 1. Helmet holder EAU00260 Helmet holder 1. Storage compartment cover 2. Storage compartment lock cover 1. Storage compartment lock EAU01869 To open the helmet holder, insert the key into the lock, and then turn the key as shown. To lock the helmet holder, place it in the original position, and then remove the key. Storage compartment The storage compartment is located on the left side of the motorcycle.
U5KS10.book Page 12 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS 3 1. Storage compartment cover 2. Pull the storage compartment cover out as shown. 1. Storage compartment cover To close the storage compartment 1. Place the storage compartment cover in its original position as shown. 2. Turn the key counterclockwise, remove it, and then close the lock cover.
U5KS10.book Page 13 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS EAU03194 Adjusting the shock absorber assembly The shock absorber assembly is located under the rider seat and is equipped with a spring preload adjusting ring. EC000015 3 CAUTION: Never attempt to turn an adjusting mechanism beyond the maximum or minimum settings. _ _ Adjust the spring preload as follows. 1. Remove the rider seat. (See page 3-10 for rider seat removal and installation procedures.) 1.
U5KS10.book Page 14 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS CI-10E Setting Minimum (soft) 1 Standard 4 Maximum (hard) 9 6. Install the mudguard and ignitor unit panel by installing the quick fasteners. 1. Quick fastener (× 3) 2. Mudguard 4. Remove the mudguard by removing each quick fastener. 1. Position indicator 2. Spring preload adjusting ring 3. Special wrench 5.
U5KS10.book Page 15 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS After removal Before installation EAU00315 WARNING This shock absorber contains highly pressurized nitrogen gas. For proper handling, read and understand the following information before handling the shock absorber. The manufacturer cannot be held responsible for property damage or personal injury that may result from improper handling. ● Do not tamper with or attempt to open the gas cylinder.
U5KS10.book Page 16 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS EAU00330 Sidestand The sidestand is located on the left side of the frame. Raise the sidestand or lower it with your foot while holding the motorcycle upright. NOTE: The built-in sidestand switch is part of the ignition circuit cut-off system, which cuts the ignition in certain situations. (See further down for an explanation of the ignition circuit cut-off system.
U5KS10.book Page 17 Tuesday, November 5, 2002 11:05 AM INSTRUMENT AND CONTROL FUNCTIONS CD-01E With the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “ 3. Turn the key to “ON”. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? 3 YES NOTE: This check is most reliable if performed with a warmed-up engine. ”. NO The neutral switch may be defective.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM PRE-OPERATION CHECKS Pre-operation check list .....................................................................
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM PRE-OPERATION CHECKS EAU01114 4- The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air pressure could have serious consequences.
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM PRE-OPERATION CHECKS ITEM Throttle grip CHECKS • Make sure that operation is smooth. • Check cable free play. • If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing. PAGE 6-15, 6-24 Control cables • Make sure that operation is smooth. • Lubricate if necessary. Wheels and tires • • • • Brake and shift pedals • Make sure that operation is smooth. • Lubricate pedal pivoting points if necessary.
U5KS10.book Page 3 Tuesday, November 5, 2002 11:05 AM PRE-OPERATION CHECKS NOTE: Pre-operation checks should be made each time the motorcycle is used. Such an inspection can be accomplished in a very short time; and the added safety it assures is more than worth the time involved. _ _ EWA00033 WARNING If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operating the motorcycle.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM OPERATION AND IMPORTANT RIDING POINTS Starting and warming up a cold engine ............................................. 5-1 Starting a warm engine ..................................................................... 5-3 Shifting .............................................................................................. 5-3 Engine break-in ................................................................................. 5-5 Parking ................
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM OPERATION AND IMPORTANT RIDING POINTS EAU00372 5- _ 5 EAU00373 EAU00376 WARNING ● Become thoroughly familiar with all operating controls and their functions before riding. Consult a Yamaha dealer regarding any control or function that you do not thoroughly understand. ● Never start the engine or operate it in a closed area for any length of time.
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM OPERATION AND IMPORTANT RIDING POINTS ECA00103 _ 1. Turn the fuel cock lever to “ON”. 2. Turn the key to “ON” and make sure that the engine stop switch is set to “ ”. 3. Shift the transmission into the neutral position. 4. Turn the starter (choke) on and completely close the throttle. (See page 3-9 for starter (choke) operation.) 5. Start the engine by pushing the start switch.
U5KS10.book Page 3 Tuesday, November 5, 2002 11:05 AM OPERATION AND IMPORTANT RIDING POINTS 6. After starting the engine, move the starter (choke) back halfway. ECA00055 CAUTION: For maximum engine life, always warm the engine up before starting off. Never accelerate hard when the engine is cold! _ EAU01258 Starting a warm engine Follow the same procedure as for starting a cold engine with the exception that the starter (choke) is not required when the engine is warm. _ 7.
U5KS10.book Page 4 Tuesday, November 5, 2002 11:05 AM OPERATION AND IMPORTANT RIDING POINTS EC000048 _ _ CAUTION: ● Even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long distances. The transmission is properly lubricated only when the engine is running. Inadequate lubrication may damage the transmission.
U5KS10.book Page 5 Tuesday, November 5, 2002 11:05 AM OPERATION AND IMPORTANT RIDING POINTS EAU01128 EAU02974 Recommended shift points The recommended shift points during acceleration and deceleration are shown in the table below. CF-04E 1st 2nd 3rd 4th 5 → → → → 2nd 3rd 4th 5th Acceleration shift point km/h (mi/h) Deceleration shift point km/h (mi/h) 20 (12.4) 30 (18.6) 40 (24.9) 50 (31.1) — 25 (15.5) 25 (15.5) 25 (15.
U5KS10.book Page 6 Tuesday, November 5, 2002 11:05 AM OPERATION AND IMPORTANT RIDING POINTS EAU00457 Parking When parking, stop the engine, remove the key from the main switch, and then turn the fuel cock lever to “OFF”. EW000058 _ WARNING Since the engine and exhaust system can become very hot, park in a place where pedestrians or children are not likely to touch them. ● Do not park on a slope or on soft ground, otherwise the motorcycle may overturn.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR Periodic maintenance ..........................................6-1 Owner’s tool kit ....................................................6-1 Periodic maintenance chart for the emission control system ...................................................6-3 General maintenance and lubrication chart .........6-4 Removing and installing the panel .......................6-7 Checking the spark plugs ........................
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00462 6- EAU01790 Safety is an obligation of the owner. Periodic inspection, adjustment and lubrication will keep your vehicle in the safest and most efficient condition possible. The most important points of motorcycle inspection, adjustment, and lubrication are explained on the following pages.
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: If you do not have the tools or experience required for a particular job, have a Yamaha dealer perform it for you. _ _ EW000062 WARNING Modifications not approved by Yamaha may cause loss of performance, excessive emissions, and render the vehicle unsafe for use. Consult a Yamaha dealer before attempting any changes.
U5KS10.book Page 3 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00471 Periodic maintenance chart for the emission control system INITIAL No. REMARKS 4,000 mi (7,000 km) or 6 months 8,000 mi (13,000 km) or 12 months 12,000 mi (19,000 km) or 18 months 16,000 mi (25,000 km) or 24 months 20,000 mi (31,000 km) or 30 months √ √ √ √ √ √ Valve clearance • Check and adjust valve clearance when engine is cold. 2 Spark plugs • Check condition. • Adjust gap and clean.
U5KS10.book Page 4 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00472 General maintenance and lubrication chart INITIAL No. ITEM 1 2 * 3 REMARKS 8,000 mi (13,000 km) or 12 months 12,000 mi (19,000 km) or 18 months 16,000 mi (25,000 km) or 24 months 20,000 mi (31,000 km) or 30 months √ √ √ √ √ • Replace. • Warm engine before draining. √ Engine oil filter element • Replace. √ • Clean or replace if necessary.
U5KS10.book Page 5 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL No. REMARKS ODOMETER READINGS 4,000 mi (7,000 km) or 6 months 8,000 mi (13,000 km) or 12 months 12,000 mi (19,000 km) or 18 months 16,000 mi (25,000 km) or 24 months 20,000 mi (31,000 km) or 30 months 11 Brake pedal and shift pedal shafts • Apply chain lube thoroughly. • Lithium-soap-based grease √ √ √ √ √ 12 Sidestand pivot • Check operation. • Lubricate and repair if necessary.
U5KS10.book Page 6 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU03907 NOTE: From 24,000 mi (37,000 km) or 36 months, repeat the maintenance intervals starting from 4,000 mi (7,000 km) or 6 months. _ _ EAU04249 NOTE: ● The air filter needs more frequent service if you are riding in unusually wet or dusty areas. ● Hydraulic brake service • After disassembling the brake master cylinders and calipers, always change the fluid.
U5KS10.book Page 7 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR 1. Panel A 1. Bolt EAU01777 Removing and installing the panel 6 The panel shown above needs to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time the panel needs to be removed and installed. EAU00491 Panel A To remove the panel Remove the bolt, and then pull the panel off as shown.
U5KS10.book Page 8 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: If any spark plug shows a distinctly different color, the engine could be defective. Do not attempt to diagnose such problems yourself. Instead, have a Yamaha dealer check the motorcycle. _ _ 1. Spark plug cover 1. Spark plug wrench EAU01673 Checking the spark plugs The spark plugs are important engine components, which are easy to check.
U5KS10.book Page 9 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR Tightening torque: Spark plug: 20 Nm (2.0 m·kgf, 14.5 ft·lbf) NOTE: If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4–1/2 turn past finger tight. However, the spark plug should be tightened to the specified torque as soon as possible. _ a. Spark plug gap 6 To install a spark plug 1.
U5KS10.book Page 10 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU04618 Engine oil The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter element replaced at the intervals specified in the periodic maintenance and lubrication chart. To check the engine oil level 1. Place the motorcycle on a level surface and hold it in an upright position.
U5KS10.book Page 11 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR ECA00133 Recommended engine oil: See page 8-1. Oil quantity: Periodic oil change: 3.0 L (2.64 Imp qt, 3.17 US qt) Total amount (dry engine): 3.6 L (3.17 Imp qt, 3.81 US qt) _ 1. Engine oil drain bolt 4. Install the engine oil drain bolt, and then tighten it to the specified torque. 6 Tightening torque: Engine oil drain bolt: 43 Nm (4.
U5KS10.book Page 12 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EC000067 CAUTION: If the oil level warning light flickers or remains on, immediately turn the engine off and have a Yamaha dealer check the vehicle. _ _ 7. Turn the engine off, and then check the oil level and correct it if necessary. NOTE: Have a Yamaha dealer replace the oil filter element when necessary. EAU04083 Final gear oil The final gear case must be checked for oil leakage before each ride.
U5KS10.book Page 13 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: The oil level should be at the brim of the filler hole. Recommended final gear oil: Hypoid gear oil SAE 80 (API GL4) or multi-grade hypoid gear oil SAE 80W-90 Oil quantity: 0.2 L (0.18 Imp qt, 0.21 US qt) _ _ 3. If the oil is below the brim of the filler hole, add sufficient oil of the recommended type to raise it to the correct level. NOTE: GL4 is a quality rating.
U5KS10.book Page 14 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00628 Adjusting the carburetors 3. Lightly tap the air filter element to remove most of the dust and dirt, and then blow the remaining dirt out with compressed air as shown. If the air filter element is damaged, replace it. The carburetors are important parts of the engine and emission control system, which require very sophisticated adjustment.
U5KS10.book Page 15 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00637 Tires The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart. To maximize the performance, durability, and safe operation of your motorcycle, note the following points regarding the specified tires.
U5KS10.book Page 16 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EW000083 Tire air pressure (measured on cold tires) Load* Front WARNING Proper loading of your motorcycle is important for several characteristics of your motorcycle, such as handling, braking, performance and safety. Do not carry loosely packed items that can shift. Securely pack your heaviest items close to the center of the motorcycle, and distribute the weight evenly from side to side.
U5KS10.book Page 17 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR _ EW000078 EAU00682 WARNING ● The front and rear tires should be of the same make and design, otherwise the handling characteristics of the motorcycle cannot be guaranteed. ● After extensive tests, only the tires listed below have been approved for this model by Yamaha Motor Co., Ltd. WARNING ● It is dangerous to ride with a worn-out tire.
U5KS10.book Page 18 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00691 Accessories and replacement parts by the use of items which have not been approved by Yamaha. _ EW000098 WARNING This motorcycle is not designed to pull a trailer or to be attached to a sidecar. The accessories or replacement parts you choose for your motorcycle should be designed specifically for this model, and they must be securely mounted to maintain the inherent stability of the original design.
U5KS10.book Page 19 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR 3. Tighten the locknut. NOTE: If the specified free play cannot be obtained as described above or if the clutch does not operate correctly, have a Yamaha dealer check the internal clutch mechanism. _ _ 1. Locknut 2. Clutch lever free play adjusting bolt c. Clutch lever free play a.
U5KS10.book Page 20 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EW000099 _ 1. Locknut 2. Brake lever free play adjusting bolt 1. Loosen the locknut at the brake lever. 2. To increase the brake lever free play, turn the adjusting bolt in direction a. To decrease the brake lever free play, turn the adjusting bolt in direction b. 3. Tighten the locknut. WARNING ● After adjusting the brake lever free play, check the free play and make sure that the brake is working properly.
U5KS10.book Page 21 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EW000109 WARNING A soft or spongy feeling in the brake pedal can indicate the presence of air in the hydraulic system. If there is air in the hydraulic system, have a Yamaha dealer bleed the system before operating the motorcycle. Air in the hydraulic system will diminish the braking performance, which may result in loss of control and an accident. _ a.
U5KS10.book Page 22 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR Front Rear 1. Brake pad wear indicator groove 1. Brake pad wear indicator groove EAU01314 Checking the front and rear brake pads The front and rear brake pads must be checked for wear at the intervals specified in the periodic maintenance and lubrication chart. Each brake pad is provided with a wear indicator groove, which allows you to check the brake pad wear without having to disassemble the brake.
U5KS10.book Page 23 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR Front brake 1. Minimum level mark 2. Brake fluid reservoir 1. Minimum level mark 2. Brake fluid reservoir EAU04856 Checking the brake fluid level 6 ● Rear brake Insufficient brake fluid may allow air to enter the brake system, possibly causing it to become ineffective. Before riding, check that the brake fluid is above the minimum level mark and replenish if necessary.
U5KS10.book Page 24 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU03976 Changing the brake fluid Have a Yamaha dealer change the brake fluid at the intervals specified in the NOTE after the periodic maintenance and lubrication chart. In addition, have the oil seals of the master cylinders and calipers as well as the brake hoses replaced at the intervals listed below or whenever they are damaged or leaking. ● Oil seals: Replace every two years.
U5KS10.book Page 25 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU03370 6 EAU03164 EAU03165 Checking and lubricating the brake and shift pedals Checking and lubricating the brake and clutch levers Checking and lubricating the sidestand The operation of the brake and shift pedals should be checked before each ride, and the pedal pivots should be lubricated if necessary.
U5KS10.book Page 26 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU02939 Checking the front fork The condition and operation of the front fork must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. To check the condition EW000115 WARNING Securely support the motorcycle so that there is no danger of it falling over.
U5KS10.book Page 27 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU00794 Checking the wheel bearings Worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. 1. Place a stand under the engine to raise the front wheel off the ground.
U5KS10.book Page 28 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR • EXTERNAL: Flush with plenty of water. • INTERNAL: Drink large quantities of water or milk and immediately call a physician. • EYES: Flush with water for 15 minutes and seek prompt medical attention. ● Batteries produce explosive hydrogen gas. Therefore, keep sparks, flames, cigarettes, etc., away from the battery and provide sufficient ventilation when charging it in an enclosed space.
U5KS10.book Page 29 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EC000102 _ 1. Positive terminal 2. Negative terminal 4. After installation, make sure that the battery leads are properly connected to the battery terminals. 6 CAUTION: keep the battery ● Always charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constantvoltage) battery charger is required.
U5KS10.book Page 30 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR Specified fuses: Main fuse: Backup fuse (odometer): Ignition fuse: Headlight fuse: Carburetor heater fuse: Signaling system fuse : 30 A 5A 10 A 15 A 15 A 10 A EC000103 1. Quick fastener (× 3) If a fuse is blown, replace it as follows. NOTE: Include steps 1–3 and 9–10 only for the main fuse. _ _ 1. Remove the rider seat. (See page 3-10 for rider seat removal and installation procedures.) 2.
U5KS10.book Page 31 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR After removal Before installation 1. Quick fastener 2. Pin 9. Place the ignitor unit panel in the original position and install the quick fasteners. 6 NOTE: To install a quick fastener, push its pin back so that it will protrude from the fastener head, then insert the fastener and push the protruding pin in until it is flush with the fastener head. _ 1. Screw (× 2) 1. Headlight bulb holder 3.
U5KS10.book Page 32 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR 5. Install the headlight bulb cover, and then connect the coupler. 6. Install the headlight unit by installing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 1. Do not touch the glass part of the bulb.
U5KS10.book Page 33 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU01579 Supporting the motorcycle 1. Screw (× 2) 1. Screw (× 3) 3. Insert a new bulb into the socket, push it in, and then turn it clockwise until it stops. 4. Install the lens by installing the screws. EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 6 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counterclockwise.
U5KS10.book Page 34 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR To service the rear wheel Raise the rear wheel off the ground by using a motorcycle stand or, if a motorcycle stand is not available, by placing a jack either under each side of the frame in front of the rear wheel or under each side of the swingarm. EAU01008 Troubleshooting Although Yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur during operation.
U5KS10.book Page 35 Tuesday, November 5, 2002 11:05 AM PERIODIC MAINTENANCE AND MINOR REPAIR EAU01297 Troubleshooting chart EW000125 WARNING Keep away open flames and do not smoke while checking or working on the fuel system. _ _ 1. Fuel There is enough fuel. Check the compression. There is no fuel. Supply fuel. There is compression. Check the ignition. There is no compression. Have a Yamaha dealer check the vehicle. Check the fuel level in the fuel tank. The engine does not start.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM MOTORCYCLE CARE AND STORAGE Care .................................................................................................. 7-1 Storage ..............................................................................................
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM MOTORCYCLE CARE AND STORAGE EAU03412 7- Care While the open design of a motorcycle reveals the attractiveness of the technology, it also makes it more vulnerable. Rust and corrosion can develop even if high-quality components are used. A rusty exhaust pipe may go unnoticed on a car, however, it detracts from the overall appearance of a motorcycle.
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM MOTORCYCLE CARE AND STORAGE ● Do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or thinner, fuel (gasoline), rust removers or inhibitors, brake fluid, antifreeze or electrolyte.
U5KS10.book Page 3 Tuesday, November 5, 2002 11:05 AM MOTORCYCLE CARE AND STORAGE 7 After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth. 2. Use a chrome polish to shine chrome, aluminum and stainlesssteel parts, including the exhaust system. (Even the thermally induced discoloring of stainlesssteel exhaust systems can be removed through polishing.) 3.
U5KS10.book Page 4 Tuesday, November 5, 2002 11:05 AM MOTORCYCLE CARE AND STORAGE Storage Short-term Always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover. ECA00014 _ _ CAUTION: ● Storing the motorcycle in a poorly ventilated room or covering it with a tarp, while it is still wet, will allow water and humidity to seep in and cause rust.
U5KS10.book Page 5 Tuesday, November 5, 2002 11:05 AM MOTORCYCLE CARE AND STORAGE 7. Check and, if necessary, correct the tire air pressure, and then lift the motorcycle so that both of its wheels are off the ground. Alternatively, turn the wheels a little every month in order to prevent the tires from becoming degraded in one spot. 8. Cover the muffler outlets with plastic bags to prevent moisture from entering them. 9. Remove the battery and fully charge it.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM SPECIFICATIONS Specifications ....................................................................................
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM SPECIFICATIONS EAU01038 8- Specifications CS-01E Model XVS1100AW/XVS1100AT Engine oil Type Dimensions Overall length Overall width Overall height 945 mm (37.2 in) 710 mm (28 in) Wheelbase 1,645 mm (64.8 in) Minimum turning radius Basic weight (with oil and full fuel tank) 10 30 50 70 90 110 130 ˚F YAMALUBE 4 (10W-30) or SAE 10W-30 1,095 mm (43.1 in) Seat height Ground clearance 0 2,460 mm (96.
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM SPECIFICATIONS Final gear oil Type Quantity Air filter Gear ratio Hypoid gear oil SAE 80 (API GL4) or multi-grade hypoid gear oil SAE 80W-90 0.2 L (0.18 Imp qt, 0.21 US qt) Dry element Fuel Type UNLEADED GASOLINE ONLY Fuel tank capacity 17 L (3.74 Imp gal, 4.49 US gal) Fuel reserve amount 4.5 L (0.99 Imp gal, 1.19 US gal) MIKUNI Model × quantity BSR37 × 2 Gap Clutch type 1.667 3rd 1.286 4th 1.032 5th 0.
U5KS10.book Page 3 Tuesday, November 5, 2002 11:05 AM SPECIFICATIONS Maximum load* 203 kg (448 lb) Rear Tire air pressure (measured or cold tires) Up to 90 kg (198 lb)* Front 225 kPa (2.25 kgf/cm2, 33 psi) Rear 250 kPa (2.50 kgf/cm2, 36 psi) 225 kPa (2.25 kgf/cm2, 33 psi) Rear 250 kPa (2.
U5KS10.book Page 4 Tuesday, November 5, 2002 11:05 AM SPECIFICATIONS Bulb voltage, wattage × quantity Headlight 12 V, 60/55 W × 1 Tail/brake light 12 V, 8/27 W × 1 Front turn signal/position light 12 V, 27/8 W × 2 Rear turn signal light 12 V, 27 W × 2 Meter lighting 14 V, 1.4 W × 2 Oil level warning light 12 V, 1.7 W × 1 Neutral indicator light 12 V, 1.7 W × 1 Turn signal indicator light 12 V, 1.7 W × 1 Engine trouble warning light 12 V, 1.7 W × 1 High beam indicator light 12 V, 1.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM CONSUMER INFORMATION Identification numbers ....................................................................... 9-1 Key identification number .................................................................. 9-1 Vehicle identification number ............................................................. 9-1 Model label ........................................................................................ 9-2 Reporting safety defects ..............
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM CONSUMER INFORMATION EAU01039 9- EAU02944 Identification numbers Record the key identification number, vehicle identification number and model label information in the spaces provided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehicle is stolen. 1. Key identification number 1. KEY IDENTIFICATION NUMBER: CA-02E 2.
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM CONSUMER INFORMATION 1. Model label EAU01804 Model label The model label is affixed to the frame under the rider seat. (See page 3-10 for rider seat removal and installation procedures.) Record the information on this label in the space provided. This information will be needed when ordering spare parts from a Yamaha dealer.
U5KS10.book Page 3 Tuesday, November 5, 2002 11:05 AM CONSUMER INFORMATION EAU01051 Reporting safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A.
U5KS10.
U5KS10.book Page 5 Tuesday, November 5, 2002 11:05 AM CONSUMER INFORMATION EAU01874 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your motorcycle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required. It is not acceptable proof of maintenance work.
U5KS10.
U5KS10.book Page 7 Tuesday, November 5, 2002 11:05 AM CONSUMER INFORMATION EAU02918 YAMAHA MOTOR CORPORATION, U.S.A.
U5KS10.
E_5ks_Consumer.fm Page 9 Wednesday, November 6, 2002 2:46 PM CONSUMER INFORMATION EAU04965 YAMAHA EXTENDED SERVICE (Y.E.S.) Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.). In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost.
E_5ks_Consumer.fm Page 10 Wednesday, November 6, 2002 2:46 PM CONSUMER INFORMATION We urge you to act now. You’ll get the excellent benefits of TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your Yamaha Limited Warranty expires. A special note: If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need. Yamaha Service Marketing P.O.
U5KS10.book Page 1 Tuesday, November 5, 2002 11:05 AM INDEX A F N Accessories and replacement parts .......6-18 Air filter element, cleaning ......................6-13 Final gear oil.......................................... 6-12 Front fork, checking ............................... 6-26 Fuel ......................................................... 3-7 Fuel cock................................................. 3-8 Fuel tank cap........................................... 3-6 Fuses, replacing ...........
U5KS10.book Page 2 Tuesday, November 5, 2002 11:05 AM INDEX Starting a warm engine............................ 5-3 Start switch.............................................. 3-4 Steering, checking ................................. 6-27 Storage.................................................... 7-4 Storage compartment ............................ 3-11 Supporting the motorcycle ..................... 6-33 T Throttle cable free play, adjusting ..........
OWNER’S MANUAL XVS1100AWR(C) XVS1100ATR(C) YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2002.11-2.
