XVZ13TF OWNER’S MANUAL
EAU00002 INTRODUCTION Congratulations on your purchase of the Yamaha Royal Star™ VENTURE®. This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle.
IMPORTANT MANUAL INFORMATION Particularly important information is distinguished in this manual by the following notations: The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Failure to follow WARNING instructions could result in severe injury or death to the motorcycle operator, a bystander or a person inspecting or repairing the motorcycle. WARNING CAUTION: A CAUTION indicates special precautions that must be taken to avoid damage to the motorcycle.
IMPORTANT MANUAL INFORMATION EW000000 WARNING PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLY AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE. DO NOT ATTEMPT TO OPERATE THIS MOTORCYCLE UNTIL YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES.
IMPORTANT MANUAL INFORMATION AFFIX DEALER LABEL HERE EAU04247 XVZ13TFP(C) OWNER’S MANUAL © 2001 by Yamaha Motor Corporation, U.S.A. 1st edition, July 2001 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in Japan.
TABLE OF CONTENTS 1 SAFETY INFORMATION 1 2 DESCRIPTION 2 3 INSTRUMENT AND CONTROL FUNCTIONS 3 4 AUDIO SYSTEM AND CB RADIO 4 5 PRE-OPERATION CHECKS 5 6 OPERATION AND IMPORTANT RIDING POINTS 6 7 PERIODIC MAINTENANCE AND MINOR REPAIR 7 8 CLEANING AND STORAGE 8 9 SPECIFICATIONS 9 10 CONSUMER INFORMATION 10 INDEX
SAFETY INFORMATION Safe riding .......................................................................................... 1-1 Protective apparel .............................................................................. 1-3 Modifications ...................................................................................... 1-3 Loading and accessories ................................................................... 1-3 Gasoline and exhaust gas...........................................................
SAFETY INFORMATION EAU03633 1- 1 MOTORCYCLES ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPENDENT UPON THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERATOR. EVERY OPERATOR SHOULD KNOW THE FOLLOWING REQUIREMENTS BEFORE RIDING THIS MOTORCYCLE. HE OR SHE SHOULD: 1. OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT SOURCE ON ALL ASPECTS OF MOTORCYCLE OPERATION. 2. OBSERVE THE WARNINGS AND MAINTENANCE REQUIREMENTS IN THE OWNER’S MANUAL. 3.
SAFETY INFORMATION 4. Many motorcycle accidents involve inexperienced operators. In fact, many operators who have been involved in accidents do not even have a current motorcycle license. a. Make sure that you are qualified and that you only lend your motorcycle to other qualified operators. b. Know your skills and limits. Staying within your limits may help you to avoid an accident. c.
SAFETY INFORMATION Protective apparel 1 The majority of fatalities from motorcycle accidents are the result of head injuries. The use of a safety helmet is the single most critical factor in the prevention or reduction of head injuries. 1. Always wear an approved helmet. 2. Wear a face shield or goggles. Wind in your unprotected eyes could contribute to an impairment of vision which could delay seeing a hazard. 3. The use of a jacket, heavy boots, trousers, gloves, etc.
SAFETY INFORMATION Loading The total weight of the operator, passenger, accessories and cargo must not exceed the maximum load limit of XVZ13TF(C): 419 lb (190 kg). When loading within this weight limit, keep the following in mind: 1. Cargo and accessory weight should be kept as low and close to the motorcycle as possible. Make sure to distribute the weight as evenly as possible on both sides of the motorcycle to minimize imbalance or instability. 2. Shifting weights can create a sudden imbalance.
SAFETY INFORMATION 1 a. Accessories fitted to the handlebar or the front fork area can create instability due to improper weight distribution or aerodynamic changes. If accessories are added to the handlebar or front fork area, they must be as lightweight as possible and should be kept to a minimum. b. Bulky or large accessories may seriously affect the stability of the motorcycle due to aerodynamic effects. Wind may attempt to lift the motorcycle, or the motorcycle may become unstable in cross winds.
SAFETY INFORMATION a. The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. b. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. c. Do not park the motorcycle near a flammable source (e.g. a kerosene heater, or near an open flame), otherwise it could catch fire. 4.
SAFETY INFORMATION EAU02977 Location of important labels Please read the following important labels carefully before operating this motorcycle.
SAFETY INFORMATION 1 2 CAUTION Cleaning with alkaline or acid cleaner, gasoline or solvent will damage windshield. Use nautral detergent.
DESCRIPTION Left view ............................................................................................. 2-1 Right view........................................................................................... 2-2 Controls and instruments ...................................................................
DESCRIPTION EAU00026 2- Royal Star™ VENTURE® Left view 2 1. Shift pedal 2. Starter (choke) knob 3. Fuel tank cap 4. Fuel cock 5. Battery 6. Coolant reservoir 7. Fuse box 2 8. Side case 9. Helmet holder 10. Tail/brake light 11.
DESCRIPTION Royal Star™ VENTURE® Right view 2 12. Muffler 13. Owner’s tool kit 14. Helmet holder 15. Travel trunk 16. Passenger seat 17. Shock absorber air valve 18. Rider seat 19. Fuel tank 20. Front fork air valve 21. Headlight 22. Front turn signal/position lights 23. Fuse box 1 24. Brake pedal 25. Rider footrest 26.
DESCRIPTION Royal Star™ VENTURE® Controls and instruments 2 1. Clutch lever 2. Audio system/CB radio control unit 3. Left handlebar switches 4. Rider headset jack 5. Speedometer unit 6. Main switch/steering lock 7. Right handlebar switches 8. Throttle grip 9.
INSTRUMENT AND CONTROL FUNCTIONS Main switch/steering lock .....................................3-1 Indicator and warning lights ................................3-2 Speedometer unit ................................................3-4 Cruise control system ..........................................3-5 Fuel gauge ...........................................................3-7 Handlebar switches .............................................3-7 Clutch lever .......................................................
INSTRUMENT AND CONTROL FUNCTIONS EAU00027 3- EAU01842 ACC (Accessory) The audio system and the auxiliary DC jack and terminals can be used in this position. Therefore, do not use the accessory position for an extended period of time, otherwise the battery may discharge. The key cannot be removed. 3 1. 2. 3. 4. ON ACC (Accessory) OFF LOCK EAU00038 EAU00029 Main switch/steering lock OFF All electrical systems are off. The key can be removed.
INSTRUMENT AND CONTROL FUNCTIONS 3 1. Push. 2. Turn. EAU03034 EW000016 WARNING Never turn the key to “OFF” or “LOCK” while the motorcycle is moving, otherwise the electrical systems will be switched off, which may result in loss of control or an accident. Make sure that the motorcycle is stopped before turning the key to “OFF” or “LOCK”. Indicator and warning lights @ @ EAU04121 1.
INSTRUMENT AND CONTROL FUNCTIONS EAU00079 6. Fuel level warning light “ ” This warning light comes on when the fuel level drops below approximately 0.9 US gal (0.8 Imp gal, 3.5 L). When this occurs, turn the fuel cock lever to the “RES” position and refuel as soon as possible. 3 EAU01773 NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. @ @ EAU01774 4.
INSTRUMENT AND CONTROL FUNCTIONS Odometer and tripmeter modes Pushing the “SELECT” button switches the display between the odometer mode “ODO” and the tripmeter modes “TRIP 1” and “TRIP 2” in the following order: ODO → TRIP 1 → TRIP 2 → ODO EAU01707 9. Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool.
INSTRUMENT AND CONTROL FUNCTIONS To reset a tripmeter, select it by pushing the “SELECT” button, and then push the “RESET” button. If you do not reset the fuel reserve tripmeter manually, it will reset itself automatically and the display will return to “TRIP 1” after refueling and traveling 5 km (3 mi).
INSTRUMENT AND CONTROL FUNCTIONS return to the set speed after the throttle grip is released. However, if the speed is increased by more than 5 mi/h (8 km/h), the cruise control system will be deactivated until the traveling speed is within 5 mi/h (8 km/h) of the set speed. 3 1. Cruise control switch 2. “CANCEL” switch To activate and set the cruise control system: 1. Push the “CRUISE” switch to the left. The “ON” indicator light will come on. 2.
INSTRUMENT AND CONTROL FUNCTIONS 3 Push the “RES/ACC” side of the cruise control switch to reactivate the system. The traveling speed will return to the previously set speed. The “RES” indicator light will flash during this time and then go off. Once the cruise control system is reactivated, the “SET” indicator light will come on. Push the “CRUISE” switch to the right to turn the cruise control system off completely.
INSTRUMENT AND CONTROL FUNCTIONS when your motorcycle is stopped where it might be a traffic hazard. EAU03889 3. Turn signal switch “ / ” To signal a right-hand turn, push this switch to “ ”. To signal a left-hand turn, push this switch to “ ”. When released, the switch returns to the center position. To cancel the turn signal lights, push the switch in after it has returned to the center position.
INSTRUMENT AND CONTROL FUNCTIONS 3 1. Clutch lever 1. Shift pedal 1. Brake lever EAU00152 EAU01215 EAU00158 Clutch lever Shift pedal Brake lever The clutch lever is located at the left handlebar grip. To disengage the clutch, pull the lever toward the handlebar grip. To engage the clutch, release the lever. The lever should be pulled rapidly and released slowly for smooth clutch operation. The clutch lever is equipped with a clutch switch, which is part of the ignition circuit cut-off system.
INSTRUMENT AND CONTROL FUNCTIONS 2. Turn the key counterclockwise to the original position, remove it, and then close the lock cover. NOTE: The fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked. @ 1. Brake pedal EAU00162 Brake pedal The brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal. @ 1. Fuel tank cap lock cover 2. Unlock.
INSTRUMENT AND CONTROL FUNCTIONS EAU00185 CAUTION: Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts. @ @ EAU04265 3 Recommended fuel: UNLEADED GASOLINE ONLY Fuel tank capacity: Total amount: 5.9 US gal (5.0 Imp gal, 22.5 L) Reserve amount: 0.9US gal (0.8 Imp gal, 3.5 L) 1. Fuel tank filler tube 2. Fuel level EAU03753 Fuel Make sure that there is sufficient fuel in the tank.
INSTRUMENT AND CONTROL FUNCTIONS OFF: closed position ON: normal position RES: reserve position 3 EAU02969 Fuel cock The fuel cock supplies fuel from the tank to the carburetors while also filtering it. The fuel cock lever positions are explained as follows and shown in the illustrations. ON With the fuel cock lever in this position, fuel flows to the carburetors. Turn the fuel cock lever to this position when starting the engine and riding.
INSTRUMENT AND CONTROL FUNCTIONS 3 1. Starter (choke) knob 1. Nut (× 2) EAU04038 Starter (choke) knob “ ” Starting a cold engine requires a richer air-fuel mixture, which is supplied by the starter (choke). Move the knob in direction a to turn on the starter (choke). Move the knob in direction b to turn off the starter (choke).
INSTRUMENT AND CONTROL FUNCTIONS 3 1. Projection 2. Seat holder To install the rider seat Insert the projection on the rear of the rider seat into the seat holder as shown, place the seat in the original position, and then tighten the nuts. 1. Helmet holder (right) 2. Unlock. 1. Helmet holder (left) 2. Unlock. EAU01782 Helmet holders To open a helmet holder Insert the key into the helmet holder lock, and then turn it as shown. NOTE: Make sure that the rider seat is properly secured before riding.
INSTRUMENT AND CONTROL FUNCTIONS ● Do not exceed the load limit of 20 lb (9 kg) for each side case and the travel trunk. ● Do not exceed the maximum load of 419 lb (190 kg) for the vehicle. not exceed 80 mph ● Do (120 km/h) when riding with the travel trunk, side cases or both installed, otherwise handling could be affected. Improper loading, poor tire or overall motorcycle conditions, poor road surfaces or adverse weather conditions may make it necessary to further reduce the riding speed. 3 1.
INSTRUMENT AND CONTROL FUNCTIONS 3 1. Travel trunk lock 2. Unlock. Travel trunk To open the travel trunk 1. Insert the key into the lock, turn it counterclockwise, and then push it in. 1. Lid resting in opened position 2. Storage pouch 2. Fold the travel trunk lid up, and then release it so that it will rest in place as shown. ECA00029 CAUTION: Do not apply excessive pressure on the travel trunk lid when it is open. @ @ 3-16 To close the travel trunk 1.
INSTRUMENT AND CONTROL FUNCTIONS EAU03719* Adjusting the front fork This front fork is equipped with air valves for adjusting the spring rate. EW000035 WARNING Always adjust both fork legs equally, otherwise poor handling and loss of stability may result. _ 3 _ NOTE: Push both sides of the lid down so that both latches snap into place. @ 2. Turn the key clockwise, and then remove it.
INSTRUMENT AND CONTROL FUNCTIONS NOTE: When checking and adjusting the air pressure, there should be no weight on the motorcycle. Spring rate: Minimum (soft)/standard: Air pressure = 0 psi (0 kgf/cm2, 0 kPa) Maximum (hard): Air pressure = 7.1 psi (0.5 kgf/cm2, 50 kPa) _ _ EC000012 CAUTION: Never exceed the maximum air pressure, otherwise the front fork oil seals may become damaged. 1. Shock absorber air valve cap EAU03721* _ _ 5. Securely install the air valve caps.
INSTRUMENT AND CONTROL FUNCTIONS ECA00050 CAUTION: Never exceed the maximum air pressure, otherwise the oil seal may become damaged. _ _ 5. Securely install the air valve cap. 3 EAU04043 Locks for the optional side cases and travel trunk There are three locks in a plastic bag located beside the owner’s tool kit. When used to replace the locks of the optional side cases and travel trunk, which can be obtained at a Yamaha dealer, these locks can be operated with the ignition key.
INSTRUMENT AND CONTROL FUNCTIONS EW000044 WARNING The motorcycle must not be ridden with the sidestand down, or if the sidestand cannot be properly moved up (or does not stay up), otherwise the sidestand could contact the ground and distract the operator, resulting in a possible loss of control. Yamaha’s ignition circuit cut-off system has been designed to assist the operator in fulfilling the responsibility of raising the sidestand before starting off.
INSTRUMENT AND CONTROL FUNCTIONS CD-01E With the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “ 3. Turn the key to “ON”. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? 3 YES NOTE: This check is most reliable if performed with a warmed-up engine. ” NO The neutral switch may be defective. The motorcycle should not be ridden until checked by a Yamaha dealer.
INSTRUMENT AND CONTROL FUNCTIONS 3 1. Auxiliary DC jack 1. Auxiliary DC terminal EAU01788 ECA00044 12-V accessories connected to the auxiliary DC jack at the front and auxiliary DC terminals under the rider seat can be used when the key is in the “ACC” or “ON” position. CAUTION: The accessories connected to the auxiliary DC jack and terminals should not be used with the engine turned off, and their combined load must never exceed 5 A or 60 W, otherwise the battery may discharge.
AUDIO SYSTEM AND CB RADIO Location of parts ............................................................................... 4-1 Headsets (optional) ........................................................................... 4-2 Control unit ........................................................................................ 4-3 Making basic settings ........................................................................ 4-5 Making mode settings ..........................................................
AUDIO SYSTEM AND CB RADIO EAU03567 4- Location of parts 4 1. 2. 3. 4. Audio system/CB radio control unit Front speaker (× 2) Rider headset jack Cassette deck lid 5. 6. 7. 8. Main switch steering lock Eject (“ ”) button Cassette deck compartment Auxiliary audio input jack 1. 2. 3. 4.
AUDIO SYSTEM AND CB RADIO @ WARNING It is dangerous to operate the audio system controls while riding. Never take your hands off the handlebars while riding. ● Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. ● @ @ CAUTION: ● Do not use the audio system or CB radio for a long period of time when the engine is not running as the battery may discharge.
AUDIO SYSTEM AND CB RADIO 4 1. 2. 3. 4. 5. Volume control knob Up/down (“ ”) switch Audio system button “AUDIO” Selection button “SELECT” CB radio button “CB” Control unit Volume control knob This knob adjusts the audio system volume, the CB radio reception volume, and the CB squelch level.
AUDIO SYSTEM AND CB RADIO Selection button “SELECT” This button is used to perform the following operations. Long push (two seconds or more) ● Selecting the preset radio station programming mode Short push (less than two seconds) ● Changing modes in the following sequence CB radio button “CB” This button is used to perform the following operations.
AUDIO SYSTEM AND CB RADIO 1. CB radio indicator light 4 Making basic settings Turning on/off the audio system To turn the power on 1. Make sure that the key is in the “ACC” or “ON” position. 2. Push the “AUDIO” button once for less than one second. Adjusting the audio system volume Turn the volume control knob until the desired audio system volume is displayed (e.g., “Vo:10”). The audio system volume can be set between “0” and “30”.
AUDIO SYSTEM AND CB RADIO Adjusting the CB reception volume Turn the control knob until the desired CB reception volume is displayed (e.g., “Vo:10”). The CB reception volume can be set between “0” and “20”. After the adjustment is made, the CB radio returns to normal operation and the CB channel appears in the display. Making mode settings General procedure The following setting procedure applies to the audio system, CB radio, and optional CD changer.
AUDIO SYSTEM AND CB RADIO 4 Selecting the output (speakers or headsets) 1. Repeatedly push the “SELECT” button for less than one second until either “SP” (speakers) or “HS” and “ ” (headsets) appears in the display. 2. Push either side of the up/down switch for less than one second to change the setting. Adjusting the bass level 1. Repeatedly push the “SELECT” button for less than one second until “BASS” appears at the bottom of the display. 2.
AUDIO SYSTEM AND CB RADIO set between “F9” (front speakers only) and “R9” (rear speakers only). NOTE: When the fade level is set to “0”, the front and rear speaker levels are the same. @ @ Adjusting the fade level (balance between front and rear speakers) 1. Make sure that the speakers are selected as the output source. (See the “Selecting the output” section on page 4-7 for selection procedures.) 2.
AUDIO SYSTEM AND CB RADIO Intercom operation Provided both the rider and passenger are wearing headsets, they can talk to each other through the intercom at any time. (See the “Adjusting the intercom volume” section on page 4-8 for adjustment procedures.) 4 Adjusting the auto volume When riding the motorcycle, external noise may override the audio system output volume. The audio system features an automatic volume control function which compensates for external noise. 1.
AUDIO SYSTEM AND CB RADIO ● To clean the tape head, use a de-magnetizing cleaning cassette, but be sure to turn the volume all the way down to avoid speaker damage. @ 1. Cassette deck compartment 2. Eject (“ ”) button 3. Cassete deck lid 4 @ Cassette deck operation @ @ WARNING ● It is dangerous to operate the cassette deck while riding. Never take your hands off the handlebars while riding. ● Keep the volume at a low enough level to be aware of traffic conditions and ensure safety.
AUDIO SYSTEM AND CB RADIO NOTE: ● The maximum number of songs that can be skipped in either direction is 9. ● To stop skipping songs, push the up/down switch in the opposite direction that songs are being skipped. @ @ 4 Playing a cassette tape 1. Make sure that the audio system is turned on. (See page 4-3.) 2. Insert a cassette tape into the cassette compartment as shown. “LOAD”, then “PLAY” appears in the display.
AUDIO SYSTEM AND CB RADIO Skipping a blank When there is a long blank portion of tape on the cassette, “BLS” appears in the display and the cassette deck automatically fast-forwards the tape to the next song. Changing the tape play direction While the cassette tape is playing, push either side of the up/down switch for more than one second to reverse the play direction. “F” appears in the display when the tape is played in the forward direction.
AUDIO SYSTEM AND CB RADIO NOTE: ● The Dolby noise reduction system has been manufactured under license from Dolby Laboratories Licensing Corporation. ● Dolby and the double “D” symbol are registered trademarks of Dolby Laboratories Licensing Corporation. @ @ 4 1. Eject (“ ”) button 1. Radio antenna Ejecting the cassette tape Push the eject (“ ”) button to eject the tape from the cassette deck. “EJCT” appears in the display, and then “CASS” starts flashing.
AUDIO SYSTEM AND CB RADIO 1. Sleeve 1. Frequency band NOTE: ● The antenna can be folded down after lifting the sleeve. ● Be sure to tighten the antenna nut securely when putting the antenna back to the original position. Selecting a frequency band This radio offers three FM bands and one AM band. Since all three FM bands cover the whole FM frequency range, any one of them can be selected for tuning in an FM station. These three FM bands are useful for categorizing FM preset stations.
AUDIO SYSTEM AND CB RADIO 3. Push either side of the up/down switch for less than one second until the desired frequency is displayed. The frequency changes in 0.2-MHz steps for FM and in 10-kHz steps for AM. 1. Preset station number 4 Tuning in a preset radio station 1. Select a frequency band. (See page 4-14.) 2. Repeatedly push either side of the up/down switch for less than one second until the desired preset station number is displayed.
AUDIO SYSTEM AND CB RADIO 3. Repeatedly push either side of the up/down switch for less than one second until the desired preset number (“1” through “6”) is displayed. NOTE: Selecting “A” will automatically program the preset stations. See the following section. @ @ Programing preset radio stations manually Up to six stations can be programmed for each frequency band (FM1, FM2, FM3, and AM) using either manual or automatic tuning. 4.
AUDIO SYSTEM AND CB RADIO Optional CD changer operation @ 4 Programing preset radio stations automatically Up to six stations can be programmed automatically for each frequency band (FM1, FM2, FM3, and AM) as follows. NOTE: This function works best in areas with strong radio signals. @ 3. Repeatedly push either side of the up/down switch for less than one second until “A” (automatic) appears in the display. 4.
AUDIO SYSTEM AND CB RADIO 1. CB antenna Playing a CD 1. Insert up to six CDs into the CD changer. Follow the manufacturer’s directions. 2. Push the “AUDIO” button until “ ” as well as the CD number and track number (e.g., “6-3”) appear in the display. The CD starts playing. NOTE: “6-3” indicates track no. 3 on CD no. 6. @ Selecting a CD Repeatedly push either side of the up/ down switch for one second or more until the number for the desired CD appears in the display.
AUDIO SYSTEM AND CB RADIO 1. Sleeve 4 NOTE: The antenna can be folded down after lifting the sleeve. @ @ This CB radio will operate on any of the 40 frequencies designated as Citizens band channels by the Federal Communications Commission (F.C.C.). This model features a frequency-synthesizing circuit with PHASE LOCK LOOP technology to assure ultraprecise frequency control. This radio has been Type-Accepted and Type-Certified by the F.C.C.
AUDIO SYSTEM AND CB RADIO NOTE: All channels, except channel 9, may be used for communications between stations operating under different licenses. Channel 9 has been reserved by the F.C.C. for emergency communications involving the immediate safety of individuals or immediate protection of property. Channel 9 may also be used to render assistance to a motorist. This is an F.C.C. rule and applies to all operators of CB radios. @ 1. CB radio indicator light Selecting a CB channel 1.
AUDIO SYSTEM AND CB RADIO 4 2. Repeatedly push either side of the up/down switch for less than one second or turn the control knob until the desired squelch level is displayed. The squelch level can be set between “1” and “20”. After the adjustment is made, the CB radio returns to normal operation and the CB channel appears in the display.
AUDIO SYSTEM AND CB RADIO Channel information Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Channel Frequency in MHz 26.965 26.975 36.985 27.005 27.015 27.025 27.035 27.055 27.065 27.075 27.085 27.105 27.115 27.125 27.135 27.155 27.165 27.175 27.185 27.205 Channel 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Channel Frequency in MHz 27.215 27.225 27.235 27.245 27.255 27.265 27.275 27.285 27.295 27.305 27.315 27.325 27.335 27.345 27.355 27.365 27.375 27.385 27.395 27.
AUDIO SYSTEM AND CB RADIO 1. “TALK” switch 4 1. Passenger “TALK” button Transmitting and receiving Transmission Push the rider “TALK” switch or the passenger “TALK” button to transmit. “TX” appears in the display.
AUDIO SYSTEM AND CB RADIO 1. Auxiliary audio input jack Reception “RX” appears in the display when the CB radio is receiving a signal. Auxiliary audio source operation Auxiliary audio equipment can be connected to, and played through, the audio system. 1. Insert the output plug of the auxiliary equipment into the jack located at the right of the cassette deck. 4-24 2. Repeatedly push the “AUDIO” button for less than one second until “AUX” appears in the display.
PRE-OPERATION CHECKS Pre-operation check list .....................................................................
PRE-OPERATION CHECKS EAU01114 5- The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual inspection, to check the following points before each ride.
PRE-OPERATION CHECKS ITEM CHECKS PAGE Clutch • • • • • Check operation. If soft or spongy, have Yamaha dealer bleed hydraulic system. Check fluid level in reservoir. If necessary, add recommended fluid to specified level. Check hydraulic system for leakage. 7-26, 7-29 Throttle grip • Make sure that operation is smooth. • Check free play. • If necessary, have Yamaha dealer make adjustment or lubricate. 7-21 Control cables • Make sure that operation is smooth. • Lubricate if necessary.
PRE-OPERATION CHECKS NOTE: Pre-operation checks should be made each time the motorcycle is used. Such an inspection can be accomplished in a very short time; and the added safety it assures is more than worth the time involved. @ @ EWA00033 WARNING If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operating the motorcycle.
OPERATION AND IMPORTANT RIDING POINTS Starting and warming up a cold engine ............................................. 6-2 Starting a warm engine ..................................................................... 6-4 Shifting .............................................................................................. 6-4 Engine break-in ................................................................................. 6-6 Parking .......................................................................
OPERATION AND IMPORTANT RIDING POINTS EAU00372 6- EAU00376 @ ● EAU00373 @ 6 WARNING ● Become thoroughly familiar with all operating controls and their functions before riding. Consult a Yamaha dealer regarding any control or function that you do not thoroughly understand. ● Never start the engine or operate it in a closed area for any length of time. Exhaust fumes are poisonous, and inhaling them can cause loss of consciousness and death within a short time.
OPERATION AND IMPORTANT RIDING POINTS EAU01789* NOTE: When the transmission is in the neutral position, the neutral indicator light should be on, otherwise have a Yamaha dealer check the electrical circuit. Starting and warming up a cold engine @ In order for the ignition circuit cut-off system to enable starting, one of the following conditions must be met: ● The transmission is in the neutral position. ● The transmission is in gear with the clutch lever pulled and the sidestand up. @ 1.
OPERATION AND IMPORTANT RIDING POINTS ECA00031 NOTE: The engine is warm when it responds normally to the throttle with the starter (choke) turned off. To avoid the possibility of excessive exhaust emissions, never leave the starter (choke) on longer than necessary. The time necessary for starter (choke) use depends upon the ambient temperature.
OPERATION AND IMPORTANT RIDING POINTS EAU01258 EC000048 Starting a warm engine @ Follow the same procedure as for starting a cold engine with the exception that the starter (choke) is not required when the engine is warm. EAU00423 Shifting Shifting gears lets you control the amount of engine power available for starting off, accelerating, climbing hills, etc. The gear positions are shown in the illustration.
OPERATION AND IMPORTANT RIDING POINTS 5. Shift the transmission into second gear. (Make sure not to shift the transmission into the neutral position.) 6. Open the throttle part way and gradually release the clutch lever. 7. Follow the same procedure when shifting to the next higher gear. NOTE: Always shift gears at the recommended shift points. @ EAU02988 6 To start out and accelerate 1. Pull the clutch lever to disengage the clutch. 2. Shift the transmission into first gear.
OPERATION AND IMPORTANT RIDING POINTS EAU01128 EAU02974 Recommended shift points The recommended shift points during acceleration and deceleration are shown in the table below. CF-04E 1st 2nd 3rd 4th → → → → 2nd 3rd 4th 5th Acceleration shift point mi/h (km/h) Deceleration shift point mi/h (km/h) 13 (20) 19 (30) 25 (40) 31 (50) 16 (25) 16 (25) 16 (25) 16 (25) Engine break-in There is never a more important period in the life of your engine than the period between 0 and 1,000 mi (1,600 km).
OPERATION AND IMPORTANT RIDING POINTS 1,000 mi (1,600 km) and beyond The vehicle can now be operated normally. EC000049 CAUTION: If any engine trouble should occur during the engine break-in period, immediately have a Yamaha dealer check the vehicle. @ @ EAU00457 Parking 6 When parking, stop the engine, remove the key from the main switch, and then turn the fuel cock lever to “OFF”.
PERIODIC MAINTENANCE AND MINOR REPAIR Periodic maintenance ..........................................7-1 Owner’s tool kit ....................................................7-2 Periodic maintenance chart for the emission control system ...................................................7-3 General maintenance and lubrication chart .........7-4 Removing and installing cowlings and panels .....7-7 Checking the spark plugs ..................................7-11 Canister (for California only) .................
PERIODIC MAINTENANCE AND MINOR REPAIR EAU00462 7- TROL ARE GROUPED SEPARATELY. THESE SERVICES REQUIRE SPECIALIZED DATA, KNOWLEDGE, AND EQUIPMENT. YAMAHA DEALERS ARE TRAINED AND EQUIPPED TO PERFORM THESE PARTICULAR SERVICES. EAU01790 Safety is an obligation of the owner. Periodic inspection, adjustment and lubrication will keep your vehicle in the safest and most efficient condition possible.
PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: If you do not have the tools or experience required for a particular job, have a Yamaha dealer perform it for you. @ @ EW000063 WARNING Modifications not approved by Yamaha may cause loss of performance and render the vehicle unsafe for use. Consult a Yamaha dealer before attempting any changes. @ 1. Owner’s tool kit EAU03568 Owner’s tool kit The owner’s tool kit is located inside the right side case. (See page 3-15 for side case opening procedures.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU00471 Periodic maintenance chart for the emission control system INITIAL No. 1 * 2 ITEM ROUTINE 600 mi (1,000 km) or 1 month ODOMETER READINGS 4,000 mi (7,000 km) or 6 months 8,000 mi (13,000 km) or 12 months 12,000 mi (19,000 km) or 18 months 16,000 mi (25,000 km) or 24 months 20,000 mi (31,000 km) or 30 months Valve clearance • Check and adjust valve clearance when engine is cold. Spark plug • Check condition. • Adjust gap and clean. √ Replace.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU00472 General maintenance and lubrication chart INITIAL No. 1 2 3 4 ITEM ROUTINE TYPE 600 mi (1,000 km) or 1 month ODOMETER READINGS 4,000 mi (7,000 km) or 6 months 8,000 mi (13,000 km) or 12 months 12,000 mi (19,000 km) or 18 months 16,000 mi (25,000 km) or 24 months √ √ √ √ √ √ 20,000 mi (31,000 km) or 30 months Engine oil • Replace. * Oil filter • Replace. - * Air filter (See NOTE page 7-6.) • Clean with compressed air.
PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL No. ITEM ROUTINE TYPE 600 mi (1,000 km) or 1 month ODOMETER READINGS 4,000 mi (7,000 km) or 6 months 8,000 mi (13,000 km) or 12 months 12,000 mi (19,000 km) or 18 months 16,000 mi (25,000 km) or 24 months 20,000 mi (31,000 km) or 30 months 10 Brake/ Clutch lever pivot shaft • Apply chain lube lightly. Lithium-soap-based grease (all-purpose grease) √ √ √ √ √ 11 Brake pedal and shift pedal shaft • Lubricate • Apply chain lube lightly.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU03892 NOTE: ● The air filter needs more frequent service if you are riding in unusually wet or dusty areas. ● Hydraulic brake and clutch systems • After disassembling the brake or clutch master cylinders, caliper cylinders or clutch release cylinder, always change the fluid. Regularly check the brake and clutch fluid levels and fill the reservoirs as required.
PERIODIC MAINTENANCE AND MINOR REPAIR 1. Cowling A 2. Panel A EAU01139 1. Cowling B 2. Panel B 3. Panel C 1. Cowling A 2. Screw (× 2) 3. Quick fastener Removing and installing cowlings and panels 7 EAU04039 Cowling A To remove the cowling Remove the screws and the quick fastener, and then pull the cowling off as shown. The cowlings and panels shown above need to be removed to perform some of the maintenance jobs described in this chapter.
PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw 1. Grommet 2. Projection 3. Cowling A 1. Cowling B 2. Screw (× 2) To install the cowling Place the cowling in the original position, and then install the screws and the quick fastener. Cowling B To remove the cowling 1. Remove cowling A. 2. Remove the screws, and then pull the cowling off as shown. EAU03634 NOTE: ● Make sure that the projection fits into the grommet.
PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw To install the cowling 1. Place the cowling in the original position, and then install the screws. NOTE: Make sure that the projection fits into the grommet. 1. Panel A 2. Screw EAU00488 Panel A To remove the panel Remove the screw, and then pull the panel off as shown. @ 7 @ 2. Install cowling A. 7-9 To install the panel Place the panel in the original position, and then install the screw.
PERIODIC MAINTENANCE AND MINOR REPAIR 1. Panel B 2. Screw EAU00488 Panel B To remove the panel Remove the screw, and then pull the panel off as shown. To install the panel Place the panel in the original position, and then install the screw. 7-10 1. Panel C 2. Screw 3. Bolt (× 2) EAU01795 Panel C To remove the panel 1. Remove the left passenger footrest by removing the bolts. 2. Remove the screw, and then pull the panel off as shown.
PERIODIC MAINTENANCE AND MINOR REPAIR 1. Spark plug cap To install the panel 1. Place the panel in the original position, and then install the screw. 2. Install the passenger footrest by installing the bolts. 7 1. Spark plug wrench EAU03329 Checking the spark plugs The spark plugs are important engine components, which are easy to check.
PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: If any spark plug shows a distinctly different color, the engine could be defective. Do not attempt to diagnose such problems yourself. Instead, have a Yamaha dealer check the motorcycle. Tightening torque: Spark plug: 12.5 ft·lb (12.5 m·kgf, 17.5 Nm) _ _ _ 3. Check each spark plug for electrode erosion and excessive carbon or other deposits, and replace it if necessary.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU04082 Engine oil and oil filter cartridge The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter cartridge replaced at the intervals specified in the periodic maintenance and lubrication chart. EAU01796 Canister (for California only) 7 This model is equipped with a canister to prevent the discharging of fuel vapor into the atmosphere. ● Check each hose connection.
PERIODIC MAINTENANCE AND MINOR REPAIR 1. Engine oil filler cap To change the engine oil (with or without oil filter cartridge replacement) 1. Start the engine, warm it up for several minutes, and then turn it off. 2. Place an oil pan under the engine to collect the used oil. 1. Engine oil drain bolt 3. Remove the engine oil filler cap and drain bolt to drain the oil from the crankcase. 1. Engine oil filter cartridge 4. Remove the oil filter cartridge with an oil filter wrench.
PERIODIC MAINTENANCE AND MINOR REPAIR 8. Add the specified amount of the recommended engine oil, and then install and tighten the oil filler cap. 1. Torque wrench 2. Oil filter wrench 6. Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque with a torque wrench. 7 Tightening torque: Oil filter cartridge: 12 ft·lb (1.7 m·kgf, 17 Nm) Recommended engine oil: See page 9-1. Oil quantity: Without oil filter cartridge replacement: 3.7 US qt (3.1 Imp qt, 3.
PERIODIC MAINTENANCE AND MINOR REPAIR EC000067 EAU01797 Coolant CAUTION: If the oil level warning light flickers or remains on, immediately turn the engine off and have a Yamaha dealer check the vehicle. _ To check the coolant level 1. Place the motorcycle on a level surface and hold it in an upright position. 2. Remove panel A. (See page 7-9 for panel removal and installation procedures.) _ 10. Turn the engine off, and then check the oil level and correct it if necessary. 1.
PERIODIC MAINTENANCE AND MINOR REPAIR EC000080 @ 1. Coolant reservoir 2. Maximum level mark 3. Minimum level mark 3. Check the coolant level in the coolant reservoir. NOTE: The coolant should be between the minimum and maximum level marks. @ 7 @ 1. Coolant reservoir cap 4. If the coolant is at or below the minimum level mark, remove the rider seat (See page 3-13 for rider seat removal and installation procedures.
PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: The radiator fan is automatically switched on or off according to the coolant temperature in the radiator. If the engine overheats, see page 7-41 for further instructions. @ @ 1. Air filter case 2. Bolt (× 2) 1. Air filter joint clamp screw EAU03569* Cleaning the air filter elements The air filter elements should be cleaned at the intervals specified in the periodic maintenance and lubrication chart.
PERIODIC MAINTENANCE AND MINOR REPAIR 1. Air filter case bolt (× 5) 4. Remove the air filter case cover by removing the bolts. 1. Air filter element 2. Air filter element screw (× 2) 5. Remove the air filter element by removing the screws. 7 7-19 1. Air filter element 6. Lightly tap the air filter element to remove most of the dust and dirt, and then blow the remaining dirt out with compressed air as shown. If the air filter element is damaged, replace it.
PERIODIC MAINTENANCE AND MINOR REPAIR 7. Install the air filter element by fitting the projection on the air filter element into the holder in the air filter case, then tightening the screws. EAU00628 Adjusting the carburetors EC000082* @ @ CAUTION: ● Make sure that the air filter element is properly seated in the air filter case. ● The engine should never be operated without the air filter element installed, otherwise the pistons and/or cylinders may become excessively worn. 1.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU00637 Adjusting the valve clearance The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart. a.
PERIODIC MAINTENANCE AND MINOR REPAIR EWA00041 WARNING Tire inflation pressure should be checked and adjusted when the temperature of the tire equals the ambient air temperature. Tire inflation pressure must be adjusted according to total weight of cargo, rider, passenger, and accessories (cowling, side cases, etc.). @ @ CE-05E Tire air pressure (measured on cold tires) Load* Front Rear Up to 198 lb (90 kg) 250 kPa 2.50 kgf/cm2 36 psi 250 kPa 2.50 kgf/cm2 36 psi 198 lb (90 kg)– maximum 250 kPa 2.
PERIODIC MAINTENANCE AND MINOR REPAIR EW000085 WARNING It is dangerous to ride with a wornout tire. When a tire tread begins to show lines, have a Yamaha dealer replace the tire immediately. Brakes, tires and related wheel parts replacement should also be left to a Yamaha dealer. EW000132 @ @ @ WARNING The front and rear tires should be of the same make and design, otherwise the handling characteristics of the motorcycle cannot be guaranteed.
PERIODIC MAINTENANCE AND MINOR REPAIR CE-11E FRONT EAU00682 Manufacturer Size Type _ Dunlop Bridgestone 150/80-16 71H 150/80-16 M/C 71H 150/80-16 71H 150/80-16 M/C 71H D404F G705 Tire air valve TR412 Valve core #9000A CE-12E REAR Manufacturer Size Type Dunlop 150/90B 15M/C 74H D404 Bridgestone 150/90B 15M/C 74H G702 Tire air valve PVR59A Valve core #9000 WARNING It is dangerous to ride with a worn-out tire.
PERIODIC MAINTENANCE AND MINOR REPAIR ● After repairing or replacing the rear tire, tighten the valve stem nut and locknut to the specified torques. EAU00691 Accessories and replacement parts EW000098 WARNING This motorcycle is not designed to pull a trailer or to be attached to a sidecar. The accessories or replacement parts you choose for your motorcycle should be designed specifically for this model, and they must be securely mounted to maintain the inherent stability of the original design.
PERIODIC MAINTENANCE AND MINOR REPAIR 3. Tighten the locknut. EW000099 @ WARNING After adjusting the brake lever free play, check the free play and make sure that the brake is working properly. ● A soft or spongy feeling in the brake lever can indicate the presence of air in the hydraulic system. If there is air in the hydraulic system, have a Yamaha dealer bleed the system before operating the motorcycle.
PERIODIC MAINTENANCE AND MINOR REPAIR EW000109 WARNING A soft or spongy feeling in the brake pedal can indicate the presence of air in the hydraulic system. If there is air in the hydraulic system, have a Yamaha dealer bleed the system before operating the motorcycle. Air in the hydraulic system will diminish the braking performance, which may result in loss of control and an accident. @ a.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU00721 Checking the front and rear brake pads Front Rear The front and rear brake pads must be checked for wear at the intervals specified in the periodic maintenance and lubrication chart. 1. Wear indicator groove (× 3) 1. Wear indicator groove EAU03938 EAU03939 Front brake pads Each front brake pad is provided with wear indicator grooves, which allow you to check the brake pad wear without having to disassemble the brake.
PERIODIC MAINTENANCE AND MINOR REPAIR Front brake Rear brake 1. Minimum level mark 1. Minimum level mark EAU03914 Checking the brake and clutch fluid levels 7 Clutch Insufficient brake or clutch fluid may allow air to enter the brake or clutch systems, possibly causing them to become ineffective. Before riding, check that the brake and clutch fluids are above the minimum level marks and replenish if necessary.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU03984 EAU03297 EAU04034 Changing the brake and clutch fluids Checking and lubricating the cables Checking and lubricating the throttle grip and cable Have a Yamaha dealer change the brake and clutch fluids at the intervals specified in the NOTE after the periodic maintenance and lubrication chart.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU03370 7 EAU03164 Checking and lubricating the brake and shift pedals Checking and lubricating the brake and clutch levers The operation of the brake and shift pedals should be checked before each ride, and the pedal pivots should be lubricated if necessary. The operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lubricated if necessary.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU02939 Recommended lubricant: Lithium-soap-based grease (all-purpose grease) Checking the front fork The condition and operation of the front fork must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. To check the condition EW000115 WARNING Securely support the motorcycle so that there is no danger of it falling over.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU00794 Checking the steering 7 To check the operation 1. Place the motorcycle on a level surface and hold it in an upright position. 2. While applying the front brake, push down hard on the handlebars several times to check if the front fork compresses and rebounds smoothly. Worn or loose steering bearings may cause danger.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU01144 EW000116 Checking the wheel bearings @ The front and rear wheel bearings must be checked at the intervals specified in the periodic maintenance and lubrication chart. If there is play in the wheel hub or if the wheel does not turn smoothly, have a Yamaha dealer check the wheel bearings. WARNING Electrolyte is poisonous and dangerous since it contains sulfuric acid, which causes severe burns.
PERIODIC MAINTENANCE AND MINOR REPAIR To charge the battery Have a Yamaha dealer charge the battery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the motorcycle is equipped with optional electrical accessories. 7 To store the battery 1. If the motorcycle will not be used for more than one month, remove the battery, fully charge it, and then place it in a cool, dry place. 2.
PERIODIC MAINTENANCE AND MINOR REPAIR 1. 2. 3. 4. 5. 6. Odometer fuse Radiator fan fuse Headlight fuse Signaling system fuse Ignition fuse Spare fuse (× 2) Fuse box 2 is located behind panel B. (See page 7-8 for panel removal and installation procedures.
PERIODIC MAINTENANCE AND MINOR REPAIR 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. 1. Bulb cover 2. Headlight coupler 1. Bulb holder 2. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EAU01802 Replacing the headlight bulb 7 This motorcycle is equipped with a quartz bulb headlight.
PERIODIC MAINTENANCE AND MINOR REPAIR 1. Do not touch this area. 1. Screw (× 2) 1. Screw (× 3) EC000105 CAUTION: Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. @ 3.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU01579 Supporting the motorcycle Since this model is not equipped with a centerstand, follow these precautions when removing the front and rear wheel or performing other maintenance requiring the motorcycle to stand upright. Check that the motorcycle is in a stable and level position before starting any maintenance. A strong wooden box can be placed under the engine for added stability.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU02990 Troubleshooting charts Starting problems or poor engine performance EW000125 WARNING Keep away open flames and do not smoke while checking or working on the fuel system. @ @ 1. Fuel There is enough fuel. Check the compression. There is no fuel. Supply fuel. There is compression. Check the ignition. There is no compression. Have a Yamaha dealer check the vehicle. Check the fuel level in the fuel tank. The engine does not start.
PERIODIC MAINTENANCE AND MINOR REPAIR Engine overheating EW000070 @ WARNING Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. ● After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape.
CLEANING AND STORAGE Cleaning ............................................................................................ 8-1 Storage ..............................................................................................
CLEANING AND STORAGE EAU01010 8- ECA00001 @ EAU03333 Cleaning Frequent, thorough cleaning of your motorcycle not only enhances its appearance, but also improves its performance and extends its life. 8 CAUTION: ● Improper cleaning can damage the windshield, cowlings, panels and other plastic parts. Use only a soft, clean cloth or sponge with mild detergent and water to clean plastic. If the windshield is scratched, use a quality plastic polishing compound after washing.
CLEANING AND STORAGE Cleaning the motorcycle 1. Rinse any dirt and degreaser off with a garden hose, using only enough pressure to do the job. ECA00032 @ CAUTION: ● Do not use high-pressure washers, since excessive high pressure may cause water seepage and deterioration of wheel bearings, the front fork, brakes, transmission seals, audio system, speakers, saddlebags, travel trunk and electrical parts.
CLEANING AND STORAGE Operate the engine for several minutes to insure the newly conditioned fuel enters the entire fuel system and carburetors. After cleaning the motorcycle Apply Yamaha Silicone Wax or another high-quality automotive-type wax on all painted and chrome-plated surfaces. Avoid combination cleaner-waxes, since many contain abrasives that may mar the paint or protective finish. When finished, start the engine and let it idle for several minutes.
CLEANING AND STORAGE NOTE: Use a Yamaha Power Cable Luber and Yamaha Lube Zall or another highquality equivalent to pressure-lubricate the cables and to purge out any moisture between the inner and outer cables. _ NOTE: If necessary, make repairs before storing the motorcycle. _ _ _ 4. Block the frame up so that both of its wheels are off the ground. 5. Cover the exhaust pipes with plastic bags to prevent moisture from entering them. 6.
SPECIFICATIONS Specifications ....................................................................................
SPECIFICATIONS EAU01038 9- Specifications CS-01E Model XVZ13TF(C) Engine oil Type Dimensions Overall length 104.5 in (2,655 mm) Overall width 35.4 in (900 mm) Overall height 61.6 in (1,565 mm) Seat height 29.5 in (750 mm) Wheelbase 67.1 in (1,705 mm) Minimum ground clearance Minimum turning radius Basic weight (with oil and full fuel tank) 0 10 30 50 70 90 110 130 ˚F YAMALUBE 4 (10W-30) or SAE 10W-30 YAMALUBE 4 (20W-40) or SAE 20W-40 6.1 in (155 mm) -20 -10 137.
SPECIFICATIONS Final gear oil Operation Type SAE80API “GL-4” Hypoid Gear Oil Quantity 0.21 US qt (0.18 lmp qt, 0.2 L) Cooling system capacity (total amount) 3.7 US qt (3.1 lmp qt, 3.5 L) Air filter Dry type element Left foot Gear ratio Fuel Type UNLEADED GASOLINE ONLY Fuel tank capacity 5.9 US gal (5.0 lmp gal, 22.5 L) Reserve amount 0.9 US gal (0.8 lmp gal, 3.5 L) MIKUNI Model × quantity BDSR32 × 4 Gap Clutch type 2nd 1.632 3rd 1.200 4th 0.960 5th 0.
SPECIFICATIONS Maximum load* 419 lb (190 kg) Rear Tire air pressure (measured on cold tires) Up to 198 lb (90 kg) Front 36 psi (2.50 kgf/cm2, 250 kPa) Rear 36 psi (2.50 kgf/cm2, 250 kPa) 36 psi (2.50 kgf/cm2, 250 kPa) Rear 41 psi (2.80 kgf/cm2, 280 kPa) Single disc brake Operation Right foot Fluid DOT 4 Suspension 198 lb (90 kg) -maximum* Front Type Front Telescopic fork Rear Swingarm (link suspension) Spring/shock absorber * Total weight of rider, passenger, cargo and accessories.
SPECIFICATIONS Bulb voltage, wattage × quantity Output impedance Headlight 12 V, 60/55 W × 1 Speaker 4Ω Tail/brake light 12 V, 8/27 W × 1 Headset 8 Ω–16 Ω Front turn signal/position light 12 V, 27/8 W × 2 Rear turn signal light 12 V, 27 W × 2 Main fuse Neutral indicator light 12 V, 1.7 W × 1 Headlight fuse 15 A High beam indicator light 12 V, 1.7 W × 1 Signaling system fuse 15 A Oil level warning light 12 V, 1.7 W × 1 Ignition fuse 10 A Turn signal indicator light 12 V, 1.
CONSUMER INFORMATION Identification numbers ..................................................................... 10-1 Key identification number ................................................................ 10-1 Vehicle identification number ........................................................... 10-1 Model label ...................................................................................... 10-2 Reporting safety defects .................................................................
CONSUMER INFORMATION EAU01039 10- EAU02944 Identification numbers Record the key identification number, vehicle identification number and model label information in the spaces provided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehicle is stolen. 1. KEY IDENTIFICATION NUMBER: 1. Key identification number CA-02E 2. VEHICLE IDENTIFICATION NUMBER: CA-02E 1.
CONSUMER INFORMATION 1. Model label EAU01804 Model label The model label is affixed to the frame under the rider seat. (See page 3-13 for rider seat removal and installation procedures.) Record the information on this label in the space provided. This information will be needed when ordering spare parts from a Yamaha dealer.
CONSUMER INFORMATION EAU01051 Reporting safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
CONSUMER INFORMATION EAU01053 Motorcycle noise regulation TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of the vehicle after such d
CONSUMER INFORMATION EAU01874 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your motorcycle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required. It is not acceptable proof of maintenance work.
CONSUMER INFORMATION Maintenance interval Date of service Servicing dealer name and address Mileage Remarks 28,000 mi (43,000 km) or 42 months 32,000 mi (49,000 km) or 48 months 36,000 mi (55,000 km) or 54 months 40,000 mi (61,000 km) or 60 months 10 10-6
CONSUMER INFORMATION EAU03066 YAMAHA MOTOR CORPORARION, U.S.A.
CONSUMER INFORMATION 10 10-8
CONSUMER INFORMATION 10 10-9
INDEX 1- Accessories and replacement parts .......7-25 Air filter elements, cleaning ....................7-18 Audio settings (basic)...............................4-5 Audio settings (modes) ............................4-6 Audio system ...........................................4-1 Auxiliary audio source ............................4-24 Auxiliary DC jack and terminals..............3-22 Coolant.................................................. 7-16 Checking..........................................
INDEX Pre-operation check list ........................... 5-1 R Radio operation ..................................... 4-13 Rider seat.............................................. 3-13 S Safety defects, reporting........................ 10-3 Safety information.................................... 1-1 Shifting .................................................... 6-4 Decelerating....................................... 6-5 Shift points .........................................
PROTECT YOUR INVESTMENT Use Genuine YAMAHA parts and Accessories. See your Authorized YAMAHA Dealer for a Genuine YAMAHA Service Manual. Printed on recycled paper LIT-11626-15-33 (4XY-28199-13) PRINTED IN JAPAN 2001 . 7 - 0.
