OWNER’S MANUAL XVZ13TFV(C) XVZ13TFMV(C) LIT-11626-19-25 2C9-28199-10
U2C910E0.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM INTRODUCTION EAU10080 Congratulations on your purchase of the Yamaha Royal Star™ VENTURE®. This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM IMPORTANT MANUAL INFORMATION EAU10130 Particularly important information is distinguished in this manual by the following notations: The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! WARNING Failure to follow WARNING instructions could result in severe injury or death to the motorcycle operator, a bystander or a person inspecting or repairing the motorcycle.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM IMPORTANT MANUAL INFORMATION AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONS AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOY THE CAPABILITIES AND THE RELIABILITY OF THIS MOTORCYCLE.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM IMPORTANT MANUAL INFORMATION EAU10192 AFFIX DEALER LABEL HERE XVZ13TFV(C)/XVZ13TFMV(C) OWNER’S MANUAL ©2005 by Yamaha Motor Corporation, U.S.A. 1st edition, May 2005 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in Japan.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM TABLE OF CONTENTS SAFETY INFORMATION ..................1-1 Location of important labels ...........1-5 DESCRIPTION ..................................2-1 Left view ..........................................2-1 Right view ........................................2-2 Controls and instruments ................2-3 INSTRUMENT AND CONTROL FUNCTIONS .......................................3-1 Main switch/steering lock ................3-1 Indicator and warning lights .
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM TABLE OF CONTENTS Checking the brake and clutch fluid levels .................................7-25 Changing the brake and clutch fluids ..........................................7-27 Checking and lubricating the cables ........................................7-27 Checking and lubricating the throttle grip and cable ................7-27 Checking and lubricating the brake and shift pedals ...............
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM SAFETY INFORMATION EAU10251 MOTORCYCLES ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPENDENT UPON THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERATOR. EVERY OPERATOR SHOULD KNOW THE FOLLOWING REQUIREMENTS BEFORE RIDING THIS MOTORCYCLE. HE OR SHE SHOULD: ● OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT SOURCE ON ALL ASPECTS OF MOTORCYCLE OPERATION.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM SAFETY INFORMATION 1 ● ● wide on a turn due to EXCESSIVE SPEED or undercornering (insufficient lean angle for the speed). • Always obey the speed limit and never travel faster than warranted by road and traffic conditions. • Always signal before turning or changing lanes. Make sure that other motorists can see you. The posture of the operator and passenger is important for proper control.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM SAFETY INFORMATION Loading The total weight of the operator, passenger, accessories and cargo must not exceed the maximum load limit. Maximum load: 190 kg (419 lb) When loading within this weight limit, keep the following in mind: ● Cargo and accessory weight should be kept as low and close to the motorcycle as possible. Make sure to distribute the weight as evenly as possible on both sides of the motorcycle to minimize imbalance or instability.
U2C910E0.book Page 4 Monday, May 16, 2005 3:08 PM SAFETY INFORMATION 1 ● tor and may limit control ability, therefore, such accessories are not recommended. Use caution when adding electrical accessories. If electrical accessories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause a dangerous loss of lights or engine power. Gasoline and exhaust gas ● GASOLINE IS HIGHLY FLAMMABLE: • Always turn the engine off when refueling.
U2C910E0.book Page 5 Monday, May 16, 2005 3:08 PM SAFETY INFORMATION EAU10381 Location of important labels Please read the following important labels carefully before operating this vehicle.
U2C910E0.book Page 6 Monday, May 16, 2005 3:08 PM SAFETY INFORMATION 1 2 CAUTION Cleaning with alkaline or acid cleaner, gasoline or solvent will damage windshield. Use neutral detergent.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM DESCRIPTION EAU10410 Left view 2 1. 2. 3. 4. 5. 6. 7. 8. Sidecase (page 3-14) 9. Helmet holder (page 3-14) 10.Tail/brake light (page 7-35) 11.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM DESCRIPTION EAU10420 Right view 2 1. 2. 3. 4. 5. 6. 7. 8. 9. Front fork air valve (page 3-16) 10.Headlight (page 7-34) 11.Front turn signal/position lights (page 7-35) 12.Fuse box 1 (page 7-32) 13.Brake pedal (page 3-9) 14.Rider footrest 15.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM DESCRIPTION EAU10430 Controls and instruments 2 1. 2. 3. 4. 5. 6. 7. 8. 9.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU10460 Main switch/steering lock EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be removed. To unlock the steering To lock the steering 3 1. Push. 2. Turn. The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU10951 ACC (Accessory) The audio system and the auxiliary DC jack and connector can be used in this position. Do not use the accessory position for an extended period of time, otherwise the battery may discharge. The key cannot be removed. EAU11003 Indicator and warning lights 3 1. 2. 3. 4. 5. 6.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU11080 EAU11270 High beam indicator light “ ” This indicator light comes on when the high beam of the headlight is switched on. Fuel level warning light “ ” This warning light comes on when the fuel level drops below approximately 3.5 L (0.92 US gal) (0.77 Imp.gal). When this occurs, turn the fuel cock lever to the “RES” position and refuel as soon as possible.
U2C910E0.book Page 4 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU36400 Speedometer unit 1. Speedometer 2. Odometer/tripmeter/fuel reserve tripmeter/clock 3. “RESET” button 4. “SELECT” button 5.
U2C910E0.book Page 5 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU11840 NOTE: After setting the clock, be sure to push the “SELECT” button before turning the key to “OFF”, otherwise the clock will not be set. 3 Fuel meter The fuel meter indicates the amount of fuel in the fuel tank. The display segments of the fuel meter disappear towards “E” (Empty) as the fuel level decreases. When only one segment is left near “E” (Empty), refuel as soon as possible.
U2C910E0.book Page 6 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS grip is released. However, if the speed is increased by more than 8 km/h (5 mi/h), the cruise control system will be deactivated until the traveling speed is within 8 km/h (5 mi/h) of the set speed. 1. “SET” indicator light 2. “RES” indicator light 3. “ON” indicator light NOTE: Pressing the cruise control switch once will change the speed in increments of 1.6 km/h (1 mi/h).
U2C910E0.book Page 7 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU12343 Handlebar switches Right EAU12430 Left 3 1. 2. 3. 4. “TALK” switch Dimmer switch “ / ” Turn signal switch “ / ” Horn switch “ ” 1. 2. 3. 4. Engine stop switch “ Hazard switch “ ” Cruise control switch Start switch “ ” / ” EAU12390 “TALK” switch See page 4-16 for an explanation of the CB radio. EAU12400 Dimmer switch “ / ” Set this switch to “ ” for the high beam and to “ ” for the low beam.
U2C910E0.book Page 8 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU12660 Engine stop switch “ / ” Set this switch to “ ” before starting the engine. Set this switch to “ ” to stop the engine in case of an emergency, such as when the vehicle overturns or when the throttle cable is stuck. ECA10061 EAU12820 Clutch lever CAUTION: Do not use the hazard lights for an extended length of time with the engine not running, otherwise the battery may discharge.
U2C910E0.book Page 9 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU12880 EAU12890 EAU12941 Shift pedal Brake lever Brake pedal 1. Shift pedal 1. Brake lever 1. Brake pedal The shift pedal is located on the left side of the engine and is used in combination with the clutch lever when shifting the gears of the 5-speed constant-mesh transmission equipped on this motorcycle. The brake lever is located at the right handlebar grip.
U2C910E0.book Page 10 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU13120 Fuel tank cap EAU13210 NOTE: The fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked. Fuel EWA10130 WARNING 3 Make sure that the fuel tank cap is properly installed before riding. 1. Fuel tank cap lock cover 2. Unlock. 1. Fuel tank filler tube 2.
U2C910E0.book Page 11 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS ECA10070 CAUTION: Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts. EAU13300 3 Recommended fuel: UNLEADED GASOLINE ONLY Fuel tank capacity: 22.5 L (5.94 US gal) (4.95 Imp.gal) Fuel reserve amount: 3.5 L (0.92 US gal) (0.77 Imp.gal) knocking (or pinging) occurs, use a gasoline of a different brand or premium unleaded fuel.
U2C910E0.book Page 12 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS ON This indicates reserve. With the fuel cock lever in this position, the fuel reserve is made available. Turn the fuel cock lever to this position if you run out of fuel while riding. When this occurs, refuel as soon as possible and be sure to turn the fuel cock lever back to “ON”! EAU13600 Starter (choke) knob “ ” 3 1. Pointed end positioned over “ON” 1.
U2C910E0.book Page 13 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU13780 Locking the steering with a padlock EAU14240 Rider seat To remove the rider seat Remove the nuts, and then pull the rider seat up. 3 1. Projection 2. Seat holder In addition to the main switch/steering lock, there are brackets on the right side of the steering head pipe for locking the steering with a padlock.
U2C910E0.book Page 14 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU14360 Helmet holders To close a helmet holder Place the helmet holder in the original position, and then remove the key. EWA11040 WARNING Never ride with a helmet attached to a helmet holder, since the helmet may hit objects, causing loss of control and possibly an accident. 1. Helmet holder (right) 2. Unlock. 1. Helmet holder (left) 2. Unlock.
U2C910E0.book Page 15 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS er conditions may make it necessary to further reduce the riding speed. Sidecases 3 To open a sidecase 1. Insert the key into the lock, turn it counterclockwise, and then push it in. 1. Storage compartment 2. Storage pouch To close a sidecase 1. Fold the sidecase lid down. 2. Turn the key clockwise, and then remove it. 1. Travel trunk lock 2. Unlock. 2.
U2C910E0.book Page 16 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS ECA10910 EAU14651 CAUTION: Adjusting the front fork Do not apply excessive pressure on the travel trunk lid when it is open. This front fork is equipped with air valves for adjusting the spring rate. EWA10180 WARNING To close the travel trunk 1. Fold the travel trunk lid up completely, and then fold it down. Always adjust both fork legs equally, otherwise poor handling and loss of stability may result. 2.
U2C910E0.book Page 17 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS 3 3. Check the air pressure in each fork leg using a low-pressure air gauge. A low-pressure air gauge is available at a Yamaha dealer. 4. To increase the spring rate and thereby harden the suspension, increase the air pressure with an air pump. To decrease the spring rate and thereby soften the suspension, decrease the air pressure by pushing each valve stem down.
U2C910E0.book Page 18 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU15301 Spring rate: Minimum (soft): Air pressure = 0 kPa (0 psi) (0 kgf/cm²) Standard: Air pressure = 0 kPa (0 psi) (0 kgf/cm²) Maximum (hard): Air pressure = 400 kPa (57 psi) (4.0 kgf/cm²) ECA11090 CAUTION: Never exceed the maximum air pressure, otherwise the oil seal may become damaged. 5. Securely install the air valve cap. Sidestand The sidestand is located on the left side of the frame.
U2C910E0.book Page 19 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU15311 Ignition circuit cut-off system 3 The ignition circuit cut-off system (comprising the sidestand switch, clutch switch and neutral switch) has the following functions. ● It prevents starting when the transmission is in gear and the sidestand is up, but the clutch lever is not pulled. ● It prevents starting when the transmission is in gear and the clutch lever is pulled, but the sidestand is still down.
U2C910E0.book Page 20 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS With the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is turned on. 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? YES NOTE: This check is most reliable if performed with a warmed-up engine. NO The neutral switch may be defective. The motorcycle should not be ridden until checked by a Yamaha dealer.
U2C910E0.book Page 21 Monday, May 16, 2005 3:08 PM INSTRUMENT AND CONTROL FUNCTIONS EAU15412 Auxiliary DC jack and connector 12-V accessories connected to the auxiliary DC jack at the front and auxiliary DC connector under the rider seat can be used when the key is in the “ACC” or “ON” position. ECA11031 CAUTION: 3 1.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO EAU15440 Location of parts 4 1. 2. 3. 4. 5. 6. Audio system/CB radio control unit Front speaker Rider headset jack Cassette deck lid Main switch/steering lock Eject (“ ”) button 7. Cassette deck compartment 8. Auxiliary audio input jack 9. Rear speaker 10.Passenger volume control knob 11.Passenger “TALK” button 12.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO EWA11370 ● ● EAU15450 Headsets (optional) WARNING It is dangerous to operate the audio system controls while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. 4 ECA11750 CAUTION: ● ● ● Do not use the audio system or CB radio for a long period of time when the engine is not running as the battery may discharge.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO EAU15462 Control unit 1. 2. 3. 4. 5. Volume control knob Up/down (“ ”) switch Audio system button “AUDIO” Selection button “SELECT” CB radio button “CB” Volume control knob This knob adjusts the audio system volume, the CB radio reception volume, and the CB squelch level. Up/down (“ ”) switch This switch is used to perform the following operations.
U2C910E0.book Page 4 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO Audio system SP/HS (Output) BASS TREB (Treble) FAD (Fade1) Long push (one second or more) ● Turning off the CB radio EAU15480 Making basic settings Turning on/off the audio system Radio frequency 2 AV (Auto volume) IC (Intercom volume) 1 This mode does not appear in the display when 2 4 the headsets are selected as the output.
U2C910E0.book Page 5 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO Adjusting the audio system volume Turning on/off the CB radio Turn the volume control knob until the desired audio system volume is displayed (e.g., “Vo:10”). The audio system volume can be set between “0” and “30”. After the adjustment is made, the audio system returns to normal operation and the current audio mode appears in the display. 1. CB radio indicator light To turn the power on 1.
U2C910E0.book Page 6 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO EAU15502 Making mode settings Audio system SP/HS (Output) General procedure The following setting procedure applies to the audio system, CB radio, and optional CD changer. 4 NOTE: ● In order to make settings in any of the audio system modes, make sure that the audio system is selected. If necessary, push the “AUDIO” button for less than one second.
U2C910E0.book Page 7 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO Adjusting the bass level 1. Repeatedly push the “SELECT” button for less than one second until “BASS” appears at the bottom of the display. 2. Repeatedly push either side of the up/down switch for less than one second until the desired level is displayed. The bass level can be set between “-6” and “+6”. Adjusting the treble level 1.
U2C910E0.book Page 8 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO NOTE: When the fade level is set to “0”, the front and rear speaker levels are the same. Adjusting the auto volume Turning on/off the CB roger beep Adjusting the intercom volume 4 1. Repeatedly push the “SELECT” button for less than one second until the intercom volume (e.g., “IC:10”) appears in the display. 2. Repeatedly push either side of the up/down switch for less than one second until the desired volume is displayed.
U2C910E0.book Page 9 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO EAU15520 EWA11380 Cassette deck operation WARNING ● ● It is dangerous to operate the cassette deck while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. ● To clean the tape head, use a de-magnetizing cleaning cassette, but be sure to turn the volume all the way down to avoid speaker damage.
U2C910E0.book Page 10 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO Skipping songs 4 While a cassette tape is playing, push either side of the up/down switch once for less than one second for each song to be skipped. Pushing “ ” skips songs in the forward direction. Pushing “ ” skips songs in the reverse direction. “APC” (auto program control) and the number of songs to be skipped (e.g., “3”) appear in the display.
U2C910E0.book Page 11 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO Turning on/off the Dolby noise reduction system Ejecting the cassette tape 1. Eject (“ EAU15533 Radio operation 4 ”) button 1. Radio antenna While the cassette tape is playing, push the eject (“ ”) button for more than two seconds to turn the Dolby B noise reduction system on or off. “B NR” appears in the display when the noise reduction system is turned on.
U2C910E0.book Page 12 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO EWA11390 Selecting a frequency band WARNING ● ● 4 ● It is dangerous to operate the radio while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. Never ride the motorcycle with the radio antenna folded down. NOTE: ● The antenna can be folded down after lifting the sleeve.
U2C910E0.book Page 13 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO tunes in the first station that has a strong enough signal to be received. Tuning in a radio station manually played. The frequency changes in 0.2-MHz steps for FM and in 10kHz steps for AM. Programming preset radio stations manually Tuning in a preset radio station 4 In order to tune in a particular radio station (e.g.
U2C910E0.book Page 14 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO 3. Repeatedly push either side of the up/down switch for less than one second until the desired preset number (“1” through “6”) is displayed. NOTE: Selecting “A” will automatically program the preset stations. See the following section. 4 4. Push the “SELECT” button once for less than one second to store the radio station selected in step 1 under the preset number selected in step 3. 5.
U2C910E0.book Page 15 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO 4. Push the “SELECT” button once for less than one second to program preset radio stations automatically. EAU15540 Optional CD changer operation EWA11400 WARNING ● ● It is dangerous to operate the CD changer while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. 1. Insert up to six CDs into the CD changer.
U2C910E0.book Page 16 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO Selecting a CD track Repeatedly push either side of the up/down switch for less than one second until the number for the desired CD track appears in the display. EAU15550 EWA11410 CB radio operation WARNING ● ● 4 ● 1. CB antenna It is dangerous to change CB radio channels or adjust the volume while riding. Never take your hands off the handlebars while riding.
U2C910E0.book Page 17 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO The Citizens Band Radio Service is under the jurisdiction of the Federal Communications Commission (F.C.C.). Any adjustments or modifications which would alter the performance of the transceiver’s original F.C.C. Type Acceptance or which would change the frequency-determining method are strictly prohibited.
U2C910E0.book Page 18 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO Adjusting the squelch level 4 The squelch is a noise suppresser designed to reduce or eliminate background noise in the absence of an incoming signal. The squelch level can be adjusted as follows. 1. Push the “CB” button once for less than one second. The squelch level appears in the display (e.g., “SQ:10”). 2.
U2C910E0.book Page 19 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO Channel information Channel Channel Frequency in MHz Channel Channel Frequency in MHz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 26.965 26.975 36.985 27.005 27.015 27.025 27.035 27.055 27.065 27.075 27.085 27.105 27.115 27.125 27.135 27.155 27.165 27.175 27.185 27.205 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 27.215 27.225 27.235 27.245 27.255 27.265 27.275 27.285 27.295 27.305 27.315 27.325 27.
U2C910E0.book Page 20 Monday, May 16, 2005 3:08 PM AUDIO SYSTEM AND CB RADIO Transmitting and receiving EAU15570 Auxiliary audio source operation Transmission Auxiliary audio equipment can be connected to, and played through, the audio system. 1. Insert the output plug of the auxiliary equipment into the jack located at the right of the cassette deck. 1. Passenger “TALK” button 4 Push the rider “TALK” switch or the passenger “TALK” button to transmit. “TX” appears in the display.
U2C910E0.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM PRE-OPERATION CHECKS EAU15591 The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual inspection, to check the following points before each ride.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM PRE-OPERATION CHECKS EAU15603 Pre-operation check list ITEM CHECKS PAGE Fuel • Check fuel level in fuel tank. • Refuel if necessary. • Check fuel line for leakage. 3-10 Engine oil • Check oil level in engine. • If necessary, add recommended oil to specified level. • Check vehicle for oil leakage. 7-12 Final gear oil • Check vehicle for oil leakage. 7-15 Coolant • Check coolant level in reservoir.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM PRE-OPERATION CHECKS ITEM 5 CHECKS Check operation. If soft or spongy, have Yamaha dealer bleed hydraulic system. Check fluid level in reservoir. If necessary, add recommended fluid to specified level. Check hydraulic system for leakage. PAGE Clutch • • • • • Throttle grip • Make sure that operation is smooth. • Check cable free play. • If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM OPERATION AND IMPORTANT RIDING POINTS EAU15950 EWA10270 WARNING ● ● ● Become thoroughly familiar with all operating controls and their functions before riding. Consult a Yamaha dealer regarding any control or function that you do not thoroughly understand. Never start the engine or operate it in a closed area for any length of time. Exhaust fumes are poisonous, and inhaling them can cause loss of consciousness and death within a short time.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM OPERATION AND IMPORTANT RIDING POINTS ECA15260 CAUTION: ● 6 ● The oil level warning light should come on when the start switch is pushed, and it should go off when the start switch is released. If the oil level warning light flickers or remains on after starting, immediately stop the engine, and then check the engine oil level and the vehicle for oil leakage. If necessary, add engine oil, and then check the warning light again.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM OPERATION AND IMPORTANT RIDING POINTS EAU16640 Starting a warm engine EAU16671 Shifting ECA10260 CAUTION: Follow the same procedure as for starting a cold engine with the exception that the starter (choke) is not required when the engine is warm. ● 1. Shift pedal 2. Neutral position ● Shifting gears lets you control the amount of engine power available for starting off, accelerating, climbing hills, etc.
U2C910E0.book Page 4 Monday, May 16, 2005 3:08 PM OPERATION AND IMPORTANT RIDING POINTS 4. At the recommended shift points shown in the following table, close the throttle, and at the same time, quickly pull the clutch lever in. 5. Shift the transmission into second gear. (Make sure not to shift the transmission into the neutral position.) 6. Open the throttle part way and gradually release the clutch lever. 7. Follow the same procedure when shifting to the next higher gear.
U2C910E0.book Page 5 Monday, May 16, 2005 3:08 PM OPERATION AND IMPORTANT RIDING POINTS ECA10331 EAU17170 CAUTION: Parking After 1000 km (600 mi) of operation, the engine oil and final gear oil must be changed, and the oil filter cartridge or element replaced. When parking, stop the engine, remove the key from the main switch, and then turn the fuel cock lever to “OFF”. 1600 km (1000 mi) and beyond The vehicle can now be operated normally.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU17231 EAU17301 PERIODIC MAINTENANCE Safety is an obligation of the owner. Periodic inspection, adjustment and lubrication will keep your vehicle in the safest and most efficient condition possible. The most important points of motorcycle inspection, adjustment, and lubrication are explained on the following pages.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EWA10340 WARNING Modifications not approved by Yamaha may cause loss of performance, excessive emissions, and render the vehicle unsafe for use. Consult a Yamaha dealer before attempting any changes.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU17600 Periodic maintenance chart for the emission control system INITIAL No. 7 ITEM ROUTINE 1 * Fuel line • Check fuel hoses for cracks or damage. • Replace if necessary. 2 * Fuel filter • Replace. 3 Spark plugs • Check condition. • Adjust gap and clean. • Replace every 8000 mi (13000 km) or 12 months. 4 * Valve clearance • Check and adjust valve clearance when engine is cold.
U2C910E0.book Page 4 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU32183 General maintenance and lubrication chart INITIAL No. ITEM ROUTINE 600 mi (1000 km) or 1 month ODOMETER READINGS 4000 mi (7000 km) or 6 months 8000 mi 12000 mi 16000 mi 20000 mi (13000 km) (19000 km) (25000 km) (31000 km) or or or or 12 months 18 months 24 months 30 months 1 * Air filter element • Clean with compressed air. • Replace if necessary. 2 * Clutch • Check operation and fluid leakage.
U2C910E0.book Page 5 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL No. ROUTINE Swingarm pivot bearings • Check bearing assemblies for looseness. • Moderately repack with lithiumsoap-based grease. 10 * Steering bearings • Check bearing assemblies for looseness. • Moderately repack with lithiumsoap-based grease every 16000 mi (25000 km) or 24 months.
U2C910E0.book Page 6 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL No. ITEM ROUTINE 600 mi (1000 km) or 1 month 18 * Rear suspension link pivots • Apply lithium-soap-based grease lightly. 19 Engine oil • Change (warm engine before draining). √ 20 * Engine oil filter cartridge • Replace.
U2C910E0.book Page 7 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL No. ITEM 26 * Lights, signals and switches ROUTINE • Check operation. • Adjust headlight beam.
U2C910E0.book Page 8 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU18712 Removing and installing cowlings and panels The cowlings and panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a cowling or panel needs to be removed and installed. 1. Cowling B 2. Panel B 3. Panel C 1. Cowling A 2. Bolt 3. Quick fastener screw EAU35841 Cowling A 1. Cowling A 2. Panel A To remove the cowling 1.
U2C910E0.book Page 9 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: Make sure that the projection fits into the grommet. 2. Install cowling A. EAU35860 Panels A and B 1. Grommet 2. Projection 3. Cowling A 1. Cowling B 2. Bolt To remove one of the panels Remove the bolt, and then pull the panel off as shown. 1. Bolt 1. Panel A 2. Bolt NOTE: Make sure that the projection fits into the grommet. 7 EAU35850 Cowling B To remove the cowling 1. Remove cowling A. 2.
U2C910E0.book Page 10 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR 1. Panel B 2. Bolt To install the panel Place the panel in the original position, and then install the bolt. EAU19332 Panel C To remove the panel 1. Remove the left passenger footrest by removing the bolts. 2. Remove the screw, and then pull the panel off as shown. 1. Panel C 2. Screw 3. Bolt To install the panel 1. Place the panel in the original position, and then install the screw. 7 2.
U2C910E0.book Page 11 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR 3. Check each spark plug for electrode erosion and excessive carbon or other deposits, and replace it if necessary. EAU19543 Checking the spark plugs The spark plugs are important engine components, which are easy to check. Since heat and deposits will cause any spark plug to slowly erode, the spark plugs should be removed and checked in accordance with the periodic maintenance and lubrication chart.
U2C910E0.book Page 12 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR 2. Clean the surface of the spark plug gasket and its mating surface, and then wipe off any grime from the spark plug threads. 3. Install the spark plug with the spark plug wrench, and then tighten it to the specified torque. EAU19672 Canister (for California only) The engine oil level should be checked before each ride.
U2C910E0.book Page 13 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: The engine oil should be between the minimum and maximum level marks. 1. Engine oil level check window 2. Maximum level mark 3. Minimum level mark 7 2. Place an oil pan under the engine to collect the used oil. 3. Remove the engine oil filler cap and drain bolt to drain the oil from the crankcase. 4. Remove the oil filter cartridge with an oil filter wrench. 1. Engine oil filler cap 1. Oil filter wrench 4.
U2C910E0.book Page 14 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR Recommended engine oil: See page 9-1. Oil quantity: Without oil filter cartridge replacement: 3.50 L (3.70 US qt) (3.08 Imp.qt) With oil filter cartridge replacement: 3.70 L (3.91 US qt) (3.26 Imp.qt) ECA11620 1. O-ring NOTE: Make sure that the O-ring is properly seated. 6. Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque with a torque wrench. CAUTION: 1.
U2C910E0.book Page 15 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU20022 NOTE: After the engine is started, the engine oil level warning light should go off if the oil level is sufficient. ECA10400 CAUTION: If the oil level warning light flickers or remains on, immediately turn the engine off and have a Yamaha dealer check the vehicle. 10. Turn the engine off, and then check the oil level and correct it if necessary.
U2C910E0.book Page 16 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR 2. Remove the oil filler bolt and drain bolt to drain the oil from the final gear case. 3. Install the final gear oil drain bolt, and then tighten it to the specified torque. 6. Check the final gear case for oil leakage. If oil is leaking, check for the cause. Tightening torque: Final gear oil drain bolt: 23 Nm (2.3 m·kgf, 17 ft·lbf) EAU20070 Coolant The coolant level should be checked before each ride.
U2C910E0.book Page 17 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR ● If water has been added to the coolant, have a Yamaha dealer check the antifreeze content of the coolant as soon as possible, otherwise the effectiveness of the coolant will be reduced. EWA10380 WARNING 1. Coolant reservoir 2. Maximum level mark 3. Minimum level mark 7 4. If the coolant is at or below the minimum level mark, remove the rider seat (See page 3-13.
U2C910E0.book Page 18 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU35193 Cleaning the air filter elements The air filter elements should be cleaned at the intervals specified in the periodic maintenance and lubrication chart. Clean the air filter elements more frequently if you are riding in unusually wet or dusty areas. 1. Remove cowlings A and B. (See page 7-8.) NOTE: Continue as follows for each air filter element. 2. Remove the air filter case bolts. 1. Air filter case 2.
U2C910E0.book Page 19 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR 7. Install the air filter element by fitting the projection on the air filter element into the holder in the air filter case, then tightening the screws. EAU21271 Carburetors The carburetors are important parts of the engine and emission control system, which require very sophisticated adjustment.
U2C910E0.book Page 20 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU21381 Checking the throttle cable free play EAU21401 EAU32541 Valve clearance Tires The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart.
U2C910E0.book Page 21 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR Tire air pressure (measured on cold tires): 0–90 kg (0–198 lb): Front: 250 kPa (36 psi) (2.50 kgf/cm²) Rear: 250 kPa (36 psi) (2.50 kgf/cm²) 90–190 kg (198–419 lb): Front: 250 kPa (36 psi) (2.50 kgf/cm²) Rear: 280 kPa (41 psi) (2.80 kgf/cm²) Maximum load*: 190 kg (419 lb) * Total weight of rider, passenger, cargo and accessories LOAD YOUR VEHICLE.
U2C910E0.book Page 22 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR ● After extensive tests, only the tires listed below have been approved for this model by Yamaha Motor Co., Ltd.
U2C910E0.book Page 23 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU22011 Accessories and replacement parts any consequences caused by the use of items which have not been approved by Yamaha. EAU22072 Clutch lever EWA10621 WARNING 7 This vehicle is not designed to pull a trailer or to be attached to a sidecar.
U2C910E0.book Page 24 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU22092 Adjusting the brake lever free play EWA10630 WARNING ● ● 1. Locknut 2. Brake lever free play adjusting screw 3. Brake lever free play The brake lever free play should measure 2.0–5.0 mm (0.08–0.20 in) as shown. Periodically check the brake lever free play and, if necessary, adjust it as follows. 1. Loosen the locknut at the brake lever. 2.
U2C910E0.book Page 25 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU22390 Checking the front and rear brake pads The front and rear brake pads must be checked for wear at the intervals specified in the periodic maintenance and lubrication chart. indicator grooves have almost disappeared, have a Yamaha dealer replace the brake pads as a set. EAU22470 EAU22660 Checking the brake and clutch fluid levels Front brake Rear brake pads EAU22430 Front brake pads 1.
U2C910E0.book Page 26 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR Clutch ● Use only the recommended quality brake fluid, otherwise the rubber seals may deteriorate, causing leakage and poor braking or clutch performance. brake fluid level goes down suddenly, have a Yamaha dealer check the cause. Recommended brake and clutch fluid: DOT 4 brake fluid 1.
U2C910E0.book Page 27 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU22750 7 EAU23090 EAU23111 Changing the brake and clutch fluids Checking and lubricating the cables Checking and lubricating the throttle grip and cable Have a Yamaha dealer change the brake and clutch fluids at the intervals specified in the NOTE after the periodic maintenance and lubrication chart.
U2C910E0.book Page 28 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU23131 Checking and lubricating the brake and shift pedals EAU23140 Recommended lubricant: Lithium-soap-based grease (all-purpose grease) Checking and lubricating the brake and clutch levers The operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lubricated if necessary.
U2C910E0.book Page 29 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU23200 Checking and lubricating the sidestand EAU23271 Checking the front fork The condition and operation of the front fork must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. To check the condition EWA10750 WARNING Securely support the vehicle so that there is no danger of it falling over.
U2C910E0.book Page 30 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU23280 EAU23290 Checking the steering Checking the wheel bearings Worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. 1. Place a stand under the engine to raise the front wheel off the ground.
U2C910E0.book Page 31 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU23370 EWA10760 Battery WARNING ● 1. Battery 2. Negative battery terminal 3. Positive battery terminal 7 This model is equipped with a sealedtype (MF) battery, which does not require any maintenance. There is no need to check the electrolyte or to add distilled water. ECA10620 CAUTION: Never attempt to remove the battery cell seals, as this would permanently damage the battery.
U2C910E0.book Page 32 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR ECA10630 CAUTION: ● ● Always keep the battery charged. Storing a discharged battery can cause permanent battery damage. To charge a sealed-type (MF) battery, a special (constant-voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a sealed-type (MF) battery charger, have a Yamaha dealer charge your battery.
U2C910E0.book Page 33 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR 1. 2. 3. 4. 5. 6. 7 Backup fuse (for odometer and clock) Radiator fan fuse Headlight fuse Signaling system fuse Ignition fuse Spare fuse If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. 3.
U2C910E0.book Page 34 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. EAU23770 Replacing the headlight bulb This model is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Disconnect the headlight coupler, and then remove the headlight bulb cover. 1. Headlight bulb holder EWA10790 WARNING 1. Headlight bulb cover 2. Headlight coupler 2.
U2C910E0.book Page 35 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU24281 Replacing a turn signal light bulb or the tail/brake light bulb 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counterclockwise. 3. Insert a new bulb into the socket, push it in, and then turn it clockwise until it stops. 4. Install the lens by installing the screws. ECA10680 CAUTION: Do not overtighten the screws, otherwise the lens may break.
U2C910E0.book Page 36 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR a jack either under each side of the frame in front of the rear wheel or under each side of the swingarm. EAU25870 Troubleshooting Although Yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur during operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and loss of power.
U2C910E0.book Page 37 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU25911 Troubleshooting charts Starting problems or poor engine performance EWA10840 WARNING Keep away open flames and do not smoke while checking or working on the fuel system. 1. Fuel There is enough fuel. Check the compression. There is no fuel. Supply fuel. There is compression. Check the ignition. There is no compression. Have a Yamaha dealer check the vehicle. Check the fuel level in the fuel tank.
U2C910E0.book Page 38 Monday, May 16, 2005 3:08 PM PERIODIC MAINTENANCE AND MINOR REPAIR Engine overheating EWA10400 WARNING ● ● Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM MOTORCYCLE CARE AND STORAGE EAU26120 Cleaning Frequent, thorough cleaning of your motorcycle not only enhances its appearance, but also improves its performance and extends its life. ECA10730 CAUTION: ● ● 8 Improper cleaning can damage the windshield, cowlings, panels and other plastic parts. Use only a soft, clean cloth or sponge with mild detergent and water to clean plastic.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM MOTORCYCLE CARE AND STORAGE or another high-quality windshield cleaner. Some cleaning compounds for plastics may leave scratches on the windshield. Before using such cleaners, test an area of the windshield which does not affect your visibility and which cannot be easily recognized. After cleaning the motorcycle Apply Yamaha Silicone Wax or another high-quality automotive-type wax on all painted and chrome-plated surfaces.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM MOTORCYCLE CARE AND STORAGE 6. If storing in a humid or salt-air atmosphere, coat all exposed metal surfaces with a light film of oil. Do not apply oil to any rubber parts or the seat cover. 7. Remove the battery and fully charge it. Store it in a cool, dry place and charge it once a month. Do not store the battery in an excessively cold or warm place [less than 0 °C (30 °F) or more than 30 °C (90 °F)].
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM SPECIFICATIONS Dimensions: Overall length: 2655 mm (104.5 in) Overall width: 900 mm (35.4 in) Overall height: 1565 mm (61.6 in) Seat height: 750 mm (29.5 in) Wheelbase: 1705 mm (67.1 in) Ground clearance: 155 mm (6.10 in) Minimum turning radius: 3500 mm (137.8 in) Weight: With oil and fuel: 394.0 kg (869 lb) Engine: Engine type: Liquid cooled 4-stroke, DOHC Cylinder arrangement: V-type 4-cylinder Displacement: 1294.0 cm³ (78.96 cu.in) Bore × stroke: 79.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM SPECIFICATIONS Transmission type: Constant mesh 5-speed Operation: Left foot operation Gear ratio: 1st: 43/17 (2.529) 2nd: 31/19 (1.632) 3rd: 30/25 (1.200) 4th: 24/25 (0.960) 5th: 22/28 (0.786) Chassis: Frame type: Double cradle Caster angle: 29.10 ° Trail: 152.0 mm (5.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM SPECIFICATIONS Charging system: AC magneto Battery: Model: YTX20L-BS Voltage, capacity: 12 V, 18.0 Ah Headlight: Bulb type: Halogen bulb Bulb voltage, wattage × quantity: Headlight: 12 V, 60 W/55.0 W × 1 Tail/brake light: 12 V, 8.0 W/27.0 W × 1 Front turn signal/position light: 12 V, 23 W/8.0 W × 2 Rear turn signal light: 12 V, 21.0 W × 2 Neutral indicator light: 12 V, 1.7 W × 1 High beam indicator light: 12 V, 1.7 W × 1 Oil level warning light: 12 V, 1.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM CONSUMER INFORMATION EAU26351 Identification numbers EAU26381 EAU26400 Key identification number Vehicle identification number 1. Key identification number 1. Vehicle identification number The key identification number is stamped into the key tag. Record this number in the space provided and use it for reference when ordering a new key. The vehicle identification number is stamped into the steering head pipe.
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM CONSUMER INFORMATION EAU26470 Model label 1. Model label The model label is affixed to the frame under the rider seat. (See page 3-13.) Record the information on this label in the space provided. This information will be needed when ordering spare parts from a Yamaha dealer.
U2C910E0.book Page 3 Monday, May 16, 2005 3:08 PM CONSUMER INFORMATION EAU26550 Reporting safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A.
U2C910E0.
U2C910E0.book Page 5 Monday, May 16, 2005 3:08 PM CONSUMER INFORMATION EAU26632 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required. It is not acceptable proof of maintenance work.
U2C910E0.
U2C910E0.book Page 7 Monday, May 16, 2005 3:08 PM CONSUMER INFORMATION EAU26702 YAMAHA MOTOR CORPORARION, U.S.A.
U2C910E0.
U2C910E0.
U2C910E0.book Page 1 Monday, May 16, 2005 3:08 PM INDEX A Accessories and replacement parts ..... 7-23 Air filter elements, cleaning .................. 7-18 Audio settings (basic) ............................. 4-4 Audio settings (modes)........................... 4-6 Audio system .......................................... 4-1 Auxiliary audio source .......................... 4-20 Auxiliary DC jack and connector........... 3-21 Cruise control switches ...........................3-8 Cruise control system...
U2C910E0.book Page 2 Monday, May 16, 2005 3:08 PM INDEX Spark plugs, checking........................... 7-11 Specifications.......................................... 9-1 Speedometer unit.................................... 3-4 Starter (choke) knob ............................. 3-12 Starting and warming up a cold engine................................................... 6-1 Start switch ............................................. 3-8 Steering, checking ................................
YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2005.05-0.
