Read this manual carefully before operating this vehicle.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM EAU10042 Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM INTRODUCTION EAU10083 Congratulations on your purchase of the Yamaha Royal Star™ VENTURE®. This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM IMPORTANT MANUAL INFORMATION EAU10132 Particularly important information is distinguished in this manual by the following notations: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING NOTICE TIP A WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM IMPORTANT MANUAL INFORMATION EAU10193 XVZ13TFZ(C)/XVZ13TFSZ(C) OWNER’S MANUAL ©2009 by Yamaha Motor Corporation, U.S.A. 1st edition, July 2009 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in Japan.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM TABLE OF CONTENTS LOCATION OF IMPORTANT LABELS .............................................1-1 SAFETY INFORMATION ..................2-1 DESCRIPTION ..................................3-1 Left view ..........................................3-1 Right view ........................................3-2 Controls and instruments.................3-3 INSTRUMENT AND CONTROL FUNCTIONS .......................................4-1 Main switch/steering lock ..............
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM TABLE OF CONTENTS Checking the brake and clutch fluid levels .........................................8-26 Changing the brake and clutch fluids ..........................................8-27 Checking and lubricating the cables ..................................8-28 Checking and lubricating the throttle grip and cable .........8-28 Checking and lubricating the brake and shift pedals .........8-28 Checking and lubricating the brake and clutch levers .......
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM LOCATION OF IMPORTANT LABELS EAU10384 1 Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM LOCATION OF IMPORTANT LABELS 1 2 NOTICE Cleaning with alkaline or acid cleaner, gasoline or solvent will damage windshield. Use neutral detergent.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM SAFETY INFORMATION EAU10283 2 Be a Responsible Owner As the vehicle’s owner, you are responsible for the safe and proper operation of your motorcycle. Motorcycles are single-track vehicles. Their safe use and operation are dependent upon the use of proper riding techniques as well as the expertise of the operator. Every operator should know the following requirements before riding this motorcycle.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM SAFETY INFORMATION ● ● due to excessive speed or undercornering (insufficient lean angle for the speed). • Always obey the speed limit and never travel faster than warranted by road and traffic conditions. • Always signal before turning or changing lanes. Make sure that other motorists can see you. The posture of the operator and passenger is important for proper control.
U2C914E0.book Page 3 Tuesday, July 28, 2009 4:59 PM SAFETY INFORMATION ● ● 2 Do not run engine in poorly ventilated or partially enclosed areas such as barns, garages, or carports. Do not run engine outdoors where engine exhaust can be drawn into a building through openings such as windows and doors. Loading Adding accessories or cargo to your motorcycle can adversely affect stability and handling if the weight distribution of the motorcycle is changed.
U2C914E0.book Page 4 Tuesday, July 28, 2009 4:59 PM SAFETY INFORMATION Aftermarket Parts, Accessories, and Modifications While you may find aftermarket products similar in design and quality to genuine Yamaha accessories, recognize that some aftermarket accessories or modifications are not suitable because of potential safety hazards to you or others.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM DESCRIPTION EAU10410 Left view 3 4 5 6,7 8 9 3 2 10 11 1 1. 2. 3. 4. 5. 6. 7. 8. 9. Helmet holder (page 4-15) 10.Tail/brake light (page 8-35) 11.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM DESCRIPTION EAU10420 Right view 2 3 4 5 6 78 9 10 3 11 12 1 13 16 1. 2. 3. 4. 5. 6. 7. 8. 15 14 9. Fuel tank (page 4-10) 10.Front fork air valve (page 4-17) 11.Headlight (page 8-34) 12.Front turn signal/position lights (page 8-35) 13.Fuse box 1 (page 8-33) 14.Brake pedal (page 4-10) 15.Rider footrest 16.
U2C914E0.book Page 3 Tuesday, July 28, 2009 4:59 PM DESCRIPTION EAU10430 Controls and instruments 3 1. 2. 3. 4. 5. 6. 7. 8. 9.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS EAU10460 Main switch/steering lock EWA10061 WARNING Never turn the key to “OFF” or “LOCK” while the vehicle is moving. Otherwise the electrical systems will be switched off, which may result in loss of control or an accident. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS The key cannot be removed. EAU11004 Indicator and warning lights 4 1. 2. 3. 4. 5. 6. Left turn signal indicator light “ High beam indicator light “ ” Oil level warning light “ ” Overdrive indicator light “O/D” Engine trouble warning light “ Fuel level warning light “ ” ” 1. 2. 3. 4.
U2C914E0.book Page 3 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS EAU11080 EAU11270 High beam indicator light “ ” This indicator light comes on when the high beam of the headlight is switched on. Fuel level warning light “ ” This warning light comes on when the fuel level drops below approximately 3.5 L (0.92 US gal, 0.77 Imp.gal). When this occurs, turn the fuel cock lever to the “RES” position and refuel as soon as possible.
U2C914E0.book Page 4 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS 4 self-diagnosis system. (See page 4-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. The warning light should come on for a few seconds, and then go off. If the warning light does not come on initially when the key is turned to “ON”, or if the warning light remains on, have a Yamaha dealer check the electrical circuit.
U2C914E0.book Page 5 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS EAU11842 TIP After resetting the fuel reserve tripmeter, the display will return to the prior mode. Clock mode To change the display to the clock mode, push the “SELECT” button for at least two seconds. To change the display back to the odometer and tripmeter modes, push the “SELECT” button. To set the clock: 1. Push both the “SELECT” and “RESET” buttons for at least two seconds. 2.
U2C914E0.book Page 6 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS grip is released. However, if the speed is increased by more than 8 km/h (5 mi/h), the cruise control system will be deactivated until the traveling speed is within 8 km/h (5 mi/h) of the set speed. 4 1. Cruise control switch 2. “CANCEL” switch 2. Press the “SET/DEC” (set/decelerate) side of the cruise control switch to activate the cruise control system. The “SET” indicator light comes on. 3.
U2C914E0.book Page 7 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS then go off. Once the cruise control system is reactivated, the “SET” indicator light will come on. Push the “CRUISE” switch to the right to turn the cruise control system off completely. EWA11071 WARNING If the cruise control system is not working correctly, the “SET” and “RES” indicator lights will flash simultaneously. If this occurs, turn the cruise control system off and have a Yamaha dealer check it.
U2C914E0.book Page 8 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS Right 4 1. 2. 3. 4. Engine stop switch “ Hazard switch “ ” Cruise control switch Start switch “ ” / ” EAU12390 “TALK” switch See page 5-16 for an explanation of the CB radio. EAU12400 Dimmer switch “ / ” Set this switch to “ ” for the high beam and to “ ” for the low beam. EAU12430 EAU12660 Turn signal switch “ / ” To signal a right-hand turn, push this switch to “ ”.
U2C914E0.book Page 9 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS The hazard lights are used in case of an emergency or to warn other drivers when your vehicle is stopped where it might be a traffic hazard. EAU12820 EAU12880 Clutch lever Shift pedal 1. Clutch lever 1. Shift pedal 2. Neutral position ECA10061 NOTICE Do not use the hazard lights for an extended length of time with the engine not running, otherwise the battery may discharge.
U2C914E0.book Page 10 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS EAU12890 EAU12941 EAU13121 Brake lever Brake pedal Fuel tank cap 1. Brake lever 1. Brake pedal The brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handlebar grip. The brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal. 1. Fuel tank cap lock cover 2. Unlock.
U2C914E0.book Page 11 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS EAU13212 TIP The fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked. EWA10131 WARNING Make sure that the fuel tank cap is properly installed before riding. Leaking fuel is a fire hazard. Fuel Make sure there is sufficient gasoline in the tank. EWA10881 WARNING Gasoline and gasoline vapors are extremely flammable.
U2C914E0.book Page 12 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS ately. If gasoline spills on your skin, wash with soap and water. If gasoline spills on your clothing, change your clothes. EAU13362 4 Recommended fuel: UNLEADED GASOLINE ONLY Fuel tank capacity: 22.5 L (5.94 US gal, 4.95 Imp.gal) Fuel reserve amount (when the fuel level warning light comes on): 3.5 L (0.92 US gal, 0.77 Imp.gal) um unleaded fuel.
U2C914E0.book Page 13 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS ON This indicates reserve. With the fuel cock lever in this position, the fuel reserve is made available. Turn the fuel cock lever to this position if you run out of fuel while riding. When this occurs, refuel as soon as possible and be sure to turn the fuel cock lever back to “ON”! EAU13600 Starter (choke) knob “ ” 4 1. Pointed end positioned over “ON” 1.
U2C914E0.book Page 14 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS EAU13780 Locking the steering with a padlock EAU14240 Rider seat To remove the rider seat Remove the nuts, and then pull the rider seat up. 1. Projection 2. Seat holder 4 In addition to the main switch/steering lock, there are brackets on the right side of the steering head pipe for locking the steering with a padlock.
U2C914E0.book Page 15 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS EAU14361 Helmet holders To close a helmet holder Place the helmet holder in the original position, and then remove the key. WARNING! Never ride with a helmet attached to a helmet holder, since the helmet may hit objects, causing loss of control and possibly an accident. [EWA11041] 1. Helmet holder (right) 2. Unlock. 1. Helmet holder (left) 2. Unlock.
U2C914E0.book Page 16 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS conditions may make it necessary to further reduce the riding speed. Sidecases To open a sidecase 1. Insert the key into the lock, turn it counterclockwise, and then push it in. 4 1. Storage compartment 2. Storage pouch To close a sidecase 1. Fold the sidecase lid down. 2. Turn the key clockwise, and then remove it. TIP Push both sides of the lid down so that both latches snap into place. 1. Sidecase lock 2. Unlock. 1.
U2C914E0.book Page 17 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS To close the travel trunk 1. Fold the travel trunk lid up completely, and then fold it down. ECA10921 EAU14654 Adjusting the front fork NOTICE To avoid locking the key in, never lock either sidecase or the travel trunk and remove the key from the lock before closing the lid. EWA10180 WARNING Always adjust both fork legs equally, otherwise poor handling and loss of stability may result.
U2C914E0.book Page 18 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS EAU14802 Spring rate: Minimum (soft): Air pressure = 0 kPa (0 kgf/cm², 0 psi) Standard: Air pressure = 0 kPa (0 kgf/cm², 0 psi) Maximum (hard): Air pressure = 50 kPa (0.5 kgf/cm², 7.1 psi) 4 1. Front fork air valve cap 5. Securely install the air valve caps. 3. Check the air pressure in each fork leg using a low-pressure air gauge. A low-pressure air gauge is available at a Yamaha dealer. 4.
U2C914E0.book Page 19 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS EAU15303 Spring rate: Minimum (soft): Air pressure = 0 kPa (0 kgf/cm², 0 psi) Standard: Air pressure = 0 kPa (0 kgf/cm², 0 psi) Maximum (hard): Air pressure = 400 kPa (4.0 kgf/cm², 57 psi) 1. Shock absorber assembly air valve cap 5. Securely install the air valve cap. 3. Check the air pressure with the air pressure gauge included in the owner’s tool kit. 4.
U2C914E0.book Page 20 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS below and have a Yamaha dealer repair it if it does not function properly. 4 EAU15314 Ignition circuit cut-off system The ignition circuit cut-off system (comprising the sidestand switch, clutch switch and neutral switch) has the following functions. ● It prevents starting when the transmission is in gear and the sidestand is up, but the clutch lever is not pulled.
U2C914E0.book Page 21 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS With the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “ 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? YES WARNING If a malfunction is noted, have a Yamaha dealer check the system before riding. ”. The neutral switch may not be working correctly.
U2C914E0.book Page 22 Tuesday, July 28, 2009 4:59 PM INSTRUMENT AND CONTROL FUNCTIONS EAU15414 Auxiliary DC jack and connector ECA11032 NOTICE The accessories connected to the auxiliary DC jack and connector should not be used with the engine turned off, and their combined load must never exceed 5 A or 60 W, otherwise the fuse may blow or the battery may discharge.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO EAU15440 Location of parts 5 1. 2. 3. 4. 5. 6. Audio system/CB radio control unit Front speaker Rider headset jack Cassette deck lid Main switch/steering lock Eject (“ ”) button 7. Cassette deck compartment 8. Auxiliary audio input jack 9. Rear speaker 10.Passenger volume control knob 11.Passenger “TALK” button 12.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO EWA11370 ● ● EAU15450 Headsets (optional) WARNING It is dangerous to operate the audio system controls while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. ECA11750 NOTICE 5 ● ● ● Do not use the audio system or CB radio for a long period of time when the engine is not running as the battery may discharge.
U2C914E0.book Page 3 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO EAU15462 Control unit 1. 2. 3. 4. 5. Volume control knob Up/down (“ ”) switch Audio system button “AUDIO” Selection button “SELECT” CB radio button “CB” Volume control knob This knob adjusts the audio system volume, the CB radio reception volume, and the CB squelch level. Up/down (“ ”) switch This switch is used to perform the following operations.
U2C914E0.book Page 4 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO Audio system SP/HS (Output) BASS TREB (Treble) FAD (Fade1) Long push (one second or more) ● Turning off the CB radio EAU15480 Making basic settings Turning on/off the audio system Radio frequency 2 AV (Auto volume) IC (Intercom volume) 1 This mode does not appear in the display when 2 the headsets are selected as the output.
U2C914E0.book Page 5 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO Adjusting the audio system volume Turning on/off the CB radio Turn the volume control knob until the desired audio system volume is displayed (e.g., “Vo:10”). The audio system volume can be set between “0” and “30”. After the adjustment is made, the audio system returns to normal operation and the current audio mode appears in the display. 1. CB radio indicator light To turn the power on 1.
U2C914E0.book Page 6 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO EAU15502 Making mode settings Audio system SP/HS (Output) General procedure The following setting procedure applies to the audio system, CB radio, and optional CD changer.
U2C914E0.book Page 7 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO Adjusting the bass level 1. Repeatedly push the “SELECT” button for less than one second until “BASS” appears at the bottom of the display. 2. Repeatedly push either side of the up/down switch for less than one second until the desired level is displayed. The bass level can be set between “-6” and “+6”. Adjusting the treble level 1.
U2C914E0.book Page 8 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO TIP When the fade level is set to “0”, the front and rear speaker levels are the same. Adjusting the auto volume Turning on/off the CB roger beep Adjusting the intercom volume 5 1. Repeatedly push the “SELECT” button for less than one second until the intercom volume (e.g., “IC:10”) appears in the display. 2. Repeatedly push either side of the up/down switch for less than one second until the desired volume is displayed.
U2C914E0.book Page 9 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO EAU15520 EWA11380 Cassette deck operation WARNING ● ● It is dangerous to operate the cassette deck while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. ● To clean the tape head, use a de-magnetizing cleaning cassette, but be sure to turn the volume all the way down to avoid speaker damage.
U2C914E0.book Page 10 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO Skipping songs Changing the tape play direction TIP ● ● The maximum number of songs that can be skipped in either direction is 9. To stop skipping songs, push the up/down switch in the opposite direction that songs are being skipped. Skipping a blank 5 While a cassette tape is playing, push either side of the up/down switch once for less than one second for each song to be skipped.
U2C914E0.book Page 11 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO Turning on/off the Dolby noise reduction system Ejecting the cassette tape 1. Eject (“ EAU15533 Radio operation ”) button 1. Radio antenna While the cassette tape is playing, push the eject (“ ”) button for more than two seconds to turn the Dolby B noise reduction system on or off. “B NR” appears in the display when the noise reduction system is turned on.
U2C914E0.book Page 12 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO EWA11390 Selecting a frequency band WARNING ● ● ● 5 It is dangerous to operate the radio while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. Never ride the motorcycle with the radio antenna folded down. TIP ● ● The antenna can be folded down after lifting the sleeve.
U2C914E0.book Page 13 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO tunes in the first station that has a strong enough signal to be received. Tuning in a radio station manually In order to tune in a particular radio station (e.g., when the signal is too weak for automatic tuning), the radio frequency can be selected manually as follows. 1. Select a frequency band. (See the “Selecting a frequency band” section.) 2.
U2C914E0.book Page 14 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO 3. Repeatedly push either side of the up/down switch for less than one second until the desired preset number (“1” through “6”) is displayed. TIP Selecting “A” will automatically program the preset stations. See the following section. 5 4. Push the “SELECT” button once for less than one second to store the radio station selected in step 1 under the preset number selected in step 3. 5.
U2C914E0.book Page 15 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO 4. Push the “SELECT” button once for less than one second to program preset radio stations automatically. EAU15540 Optional CD changer operation EWA11400 WARNING ● ● It is dangerous to operate the CD changer while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. 1. Insert up to six CDs into the CD changer.
U2C914E0.book Page 16 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO Selecting a CD track Repeatedly push either side of the up/down switch for less than one second until the number for the desired CD track appears in the display. EAU15551 EWA11410 CB radio operation WARNING ● ● ● 1. CB antenna 5 It is dangerous to change CB radio channels or adjust the volume while riding. Never take your hands off the handlebars while riding.
U2C914E0.book Page 17 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO The Citizens Band Radio Service is under the jurisdiction of the Federal Communications Commission (F.C.C.). Any adjustments or modifications which would alter the performance of the transceiver’s original F.C.C. Type Acceptance or which would change the frequency-determining method are strictly prohibited.
U2C914E0.book Page 18 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO Adjusting the squelch level 5 The squelch is a noise suppresser designed to reduce or eliminate background noise in the absence of an incoming signal. The squelch level can be adjusted as follows. 1. Push the “CB” button once for less than one second. The squelch level appears in the display (e.g., “SQ:10”). 2.
U2C914E0.book Page 19 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO Channel information Channel Channel Frequency in MHz Channel Channel Frequency in MHz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 26.965 26.975 36.985 27.005 27.015 27.025 27.035 27.055 27.065 27.075 27.085 27.105 27.115 27.125 27.135 27.155 27.165 27.175 27.185 27.205 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 27.215 27.225 27.235 27.245 27.255 27.265 27.275 27.285 27.295 27.305 27.315 27.325 27.
U2C914E0.book Page 20 Tuesday, July 28, 2009 4:59 PM AUDIO SYSTEM AND CB RADIO Transmitting and receiving EAU15570 Auxiliary audio source operation Transmission Push the rider “TALK” switch or the passenger “TALK” button to transmit. “TX” appears in the display. Auxiliary audio equipment can be connected to, and played through, the audio system. 1. Insert the output plug of the auxiliary equipment into the jack located at the right of the cassette deck.
U2C914E0.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM FOR YOUR SAFETY – PRE-OPERATION CHECKS EAU15596 Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the Owner’s Manual. EWA11151 WARNING Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage. Do not operate the vehicle if you find any problem.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM FOR YOUR SAFETY – PRE-OPERATION CHECKS ITEM CHECKS PAGE Rear brake • • • • • • • Check operation. If soft or spongy, have Yamaha dealer bleed hydraulic system. Check brake pads for wear. Replace if necessary. Check fluid level in reservoir. If necessary, add recommended brake fluid to specified level. Check hydraulic system for leakage. 8-25, 8-26 Clutch • • • • • Check operation. If soft or spongy, have Yamaha dealer bleed hydraulic system.
U2C914E0.book Page 3 Tuesday, July 28, 2009 4:59 PM FOR YOUR SAFETY – PRE-OPERATION CHECKS ITEM CHECKS Instruments, lights, signals and switches • Check operation. • Correct if necessary. Sidestand switch • Check operation of ignition circuit cut-off system. • If system is not working correctly, have Yamaha dealer check vehicle.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM OPERATION AND IMPORTANT RIDING POINTS EAU15951 Read the Owner’s Manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your Yamaha dealer. EWA10271 WARNING Failure to familiarize yourself with the controls can lead to loss of control, which could cause an accident or injury.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM OPERATION AND IMPORTANT RIDING POINTS EAU16640 TIP The engine is warm when it responds quickly to the throttle with the starter (choke) turned off. To avoid the possibility of excessive exhaust emissions, never leave the starter (choke) on longer than necessary. The time necessary for starter (choke) use depends upon the ambient temperature.
U2C914E0.book Page 3 Tuesday, July 28, 2009 4:59 PM OPERATION AND IMPORTANT RIDING POINTS ECA10260 NOTICE ● ● Even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long distances. The transmission is properly lubricated only when the engine is running. Inadequate lubrication may damage the transmission.
U2C914E0.book Page 4 Tuesday, July 28, 2009 4:59 PM OPERATION AND IMPORTANT RIDING POINTS EAU16841 Engine break-in There is never a more important period in the life of your engine than the period between 0 and 1600 km (1000 mi). For this reason, you should read the following material carefully. Since the engine is brand new, do not put an excessive load on it for the first 1600 km (1000 mi). The various parts in the engine wear and polish themselves to the correct operating clearances.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU17232 Periodic inspection, adjustment, and lubrication will keep your vehicle in the safest and most efficient condition possible. Safety is an obligation of the vehicle owner/operator. The most important points of vehicle inspection, adjustment, and lubrication are explained on the following pages.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU17412 Owner’s tool kit 1. Owner’s tool kit 8 The owner’s tool kit is located inside the right sidecase. (See page 4-15.) The service information included in this manual and the tools provided in the owner’s tool kit are intended to assist you in the performance of preventive maintenance and minor repairs.
U2C914E0.book Page 3 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU48490 TIP ● ● From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months. Items marked with an asterisk require special tools, data and technical skills, have a Yamaha dealer perform the service. EAU17601 Periodic maintenance chart for the emission control system INITIAL No. ITEM ROUTINE 1 * Fuel line • Check fuel hoses for cracks or damage.
U2C914E0.book Page 4 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ITEM ROUTINE 7 * Idle speed • Check and adjust engine idle speed. 8 * Exhaust system • Check for leakage. • Tighten if necessary. • Replace gasket(s) if necessary. 9 * Evaporative emission control system (for California only) • Check control system for damage. • Replace if necessary.
U2C914E0.book Page 5 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU32186 General maintenance and lubrication chart INITIAL No. ITEM ROUTINE 1 * Air filter elements • Clean with compressed air. • Replace if necessary. 2 * Clutch • Check operation and fluid leakage. • Correct if necessary.
U2C914E0.book Page 6 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ROUTINE Swingarm pivot bearings • Check bearing assemblies for looseness. • Moderately repack with lithiumsoap-based grease. 10 * Steering bearings • Check bearing assemblies for looseness. • Moderately repack with lithiumsoap-based grease every 16000 mi (25000 km) or 24 months.
U2C914E0.book Page 7 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ITEM ROUTINE 600 mi (1000 km) or 1 month ODOMETER READINGS 4000 mi (7000 km) or 6 months 8000 mi 12000 mi 16000 mi 20000 mi (13000 km) (19000 km) (25000 km) (31000 km) or or or or 12 months 18 months 24 months 30 months 18 * Front fork • Check operation and for oil leakage. • Replace if necessary. √ √ √ √ √ 19 * Shock absorber assembly • Check operation and for oil leakage.
U2C914E0.book Page 8 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ITEM ROUTINE 27 * Throttle grip housing and cable • Check operation and free play. • Adjust the throttle cable free play if necessary. • Lubricate the throttle grip housing and cable. 28 * Lights, signals and switches • Check operation. • Adjust headlight beam.
U2C914E0.book Page 9 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU18712 Removing and installing cowlings and panels The cowlings and panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a cowling or panel needs to be removed and installed. 1. Cowling B 2. Panel B 3. Panel C 1. Cowling A 2. Bolt 3. Quick fastener screw EAU35841 Cowling A 1. Cowling A 2. Panel A To remove the cowling 1.
U2C914E0.book Page 10 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT TIP Make sure that the projection fits into the grommet. 2. Install cowling A. EAU35860 Panels A and B 1. Grommet 2. Projection 3. Cowling A To remove one of the panels Remove the bolt, and then pull the panel off as shown. 1. Cowling B 2. Bolt TIP Make sure that the projection fits into the grommet. EAU35850 Cowling B 8 To remove the cowling 1. Remove cowling A. 2.
U2C914E0.book Page 11 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT 1. Panel B 2. Bolt To install the panel Place the panel in the original position, and then install the bolt. EAU19333 Panel C To remove the panel 1. Remove panel B. 2. Remove the left passenger footrest by removing the bolts. 3. Remove the screw, and then pull the panel off as shown. 1. Panel C 2. Screw 3. Bolt To install the panel 1. Place the panel in the original position, and then install the screw. 8 2.
U2C914E0.book Page 12 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT 3. Check each spark plug for electrode erosion and excessive carbon or other deposits, and replace it if necessary. EAU19545 Checking the spark plugs The spark plugs are important engine components, which are easy to check. Since heat and deposits will cause any spark plug to slowly erode, the spark plugs should be removed and checked in accordance with the periodic maintenance and lubrication chart.
U2C914E0.book Page 13 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT To install a spark plug 1. Clean the surface of the spark plug gasket and its mating surface, and then wipe off any grime from the spark plug threads. 2. Install the spark plug with the spark plug wrench, and then tighten it to the specified torque. EAU19672 Canister (for California only) The engine oil level should be checked before each ride.
U2C914E0.book Page 14 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT 4. Remove the engine oil filler cap, the engine oil drain bolt and its gasket to drain the oil from the crankcase. TIP Skip steps 5–7 if the oil filter cartridge is not being replaced. 5. Remove the oil filter cartridge with an oil filter wrench. 1. Engine oil level check window 2. Maximum level mark 3. Minimum level mark 4.
U2C914E0.book Page 15 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT Recommended engine oil: See page 10-1. Oil quantity: Without oil filter cartridge replacement: 3.50 L (3.70 US qt, 3.08 Imp.qt) With oil filter cartridge replacement: 3.70 L (3.91 US qt, 3.26 Imp.qt) 1. O-ring TIP Make sure that the O-ring is properly seated. 7. Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque with a torque wrench. 1. Torque wrench 2.
U2C914E0.book Page 16 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT 10. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and check for the cause. TIP After the engine is started, the engine oil level warning light should go off if the oil level is sufficient. EAU20026 Final gear oil The final gear case must be checked for oil leakage before each ride.
U2C914E0.book Page 17 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU20070 Tightening torque: Final gear oil filler bolt: 23 Nm (2.3 m·kgf, 17 ft·lbf) To change the final gear oil 1. Place an oil pan under the final gear case to collect the used oil. 2. Remove the final gear oil filler bolt, the final gear oil drain bolt and their gasket to drain the oil from the final gear case. Tightening torque: Final gear oil drain bolt: 23 Nm (2.3 m·kgf, 17 ft·lbf) 4.
U2C914E0.book Page 18 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT 1. Coolant reservoir 2. Maximum level mark 3. Minimum level mark 8 4. If the coolant is at or below the minimum level mark, remove the rider seat (See page 4-14.), open the reservoir cap, add coolant to the maximum level mark, and then close the reservoir cap and install the rider seat. WARNING! Remove only the coolant reservoir cap. Never attempt to remove the radiator cap when the engine is hot.
U2C914E0.book Page 19 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU35196 Cleaning the air filter elements The air filter elements should be cleaned at the intervals specified in the periodic maintenance and lubrication chart. Clean or, if necessary, replace the air filter elements more frequently if you are riding in unusually wet or dusty areas. 1. Remove cowlings A and B. (See page 8-9.) TIP Continue as follows for each air filter element. 2. Remove the air filter case bolts.
U2C914E0.book Page 20 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT 7. Install the air filter element by fitting the projection on the air filter element into the holder in the air filter case, then tightening the screws. NOTICE: Make sure that the air filter element is properly seated in the air filter case. The engine should never be operated without the air filter element installed, otherwise the piston(s) and/or cylinder(s) may become excessively worn.
U2C914E0.book Page 21 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU44734 Checking the engine idling speed EAU21382 Checking the throttle cable free play Check the engine idling speed and, if necessary, have it corrected by a Yamaha dealer. Engine idling speed: 950–1050 r/min EAU21401 Valve clearance The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise.
U2C914E0.book Page 22 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU32542 Tires To maximize the performance, durability, and safe operation of your motorcycle, note the following points regarding the specified tires. Tire air pressure The tire air pressure should be checked and, if necessary, adjusted before each ride. EWA10501 WARNING 8 Operation of this vehicle with improper tire pressure may cause severe injury or death from loss of control.
U2C914E0.book Page 23 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EWA10520 WARNING It is dangerous to ride with a wornout tire. When a tire tread begins to show lines, have a Yamaha dealer replace the tire immediately. Brakes, tires and related wheel parts replacement should also be left to a Yamaha dealer. Tire information This motorcycle is equipped with cast wheels and tubeless tires.
U2C914E0.book Page 24 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU22073 Clutch lever EAU22093 Adjusting the brake lever free play 1 2 1. Valve stem nut 2. Valve stem locknut 1. No clutch lever free play Tightening torques: Valve stem nut: 1.6 Nm (0.16 m·kgf, 1.2 ft·lbf) Valve stem locknut: 1.6 Nm (0.16 m·kgf, 1.2 ft·lbf) 8 Since this model is equipped with a hydraulic clutch, adjusting the clutch lever free play is not needed.
U2C914E0.book Page 25 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT 3. Tighten the locknut. EAU22282 EWA10630 WARNING ● ● After adjusting the brake lever free play, check the free play and make sure that the brake is working properly. A soft or spongy feeling in the brake lever can indicate the presence of air in the hydraulic system. If there is air in the hydraulic system, have a Yamaha dealer bleed the system before operating the motorcycle.
U2C914E0.book Page 26 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT indicator grooves have almost disappeared, have a Yamaha dealer replace the brake pads as a set. EAU22470 EAU22660 Checking the brake and clutch fluid levels Clutch Front brake Rear brake pads 1. Minimum level mark 1. Minimum level mark 1.
U2C914E0.book Page 27 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT ● Use only the recommended quality brake fluid, otherwise the rubber seals may deteriorate, causing leakage and poor braking or clutch performance. brake fluid level goes down suddenly, have a Yamaha dealer check the cause. Have a Yamaha dealer change the brake and clutch fluids at the intervals specified in the TIP after the periodic maintenance and lubrication chart.
U2C914E0.book Page 28 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23112 EAU23093 Checking and lubricating the cables Checking and lubricating the throttle grip and cable The operation of all control cables and the condition of the cables should be checked before each ride, and the cables and cable ends should be lubricated if necessary. If a cable is damaged or does not move smoothly, have a Yamaha dealer check or replace it.
U2C914E0.book Page 29 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU43600 Recommended lubricant: Lithium-soap-based grease EAU23202 Checking and lubricating the brake and clutch levers Checking and lubricating the sidestand The operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lubricated if necessary.
U2C914E0.book Page 30 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAUM1651 EAU23251 Lubricating the swingarm pivots Lubricating the rear suspension The swingarm pivots must be lubricated by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart. The pivoting points of the rear suspension must be lubricated by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart.
U2C914E0.book Page 31 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23283 Checking the steering ECA10590 NOTICE If any damage is found or the front fork does not operate smoothly, have a Yamaha dealer check or repair it. Worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. 1.
U2C914E0.book Page 32 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23374 EWA10760 Battery WARNING ● 1. Battery 2. Negative battery lead (black) 3. Positive battery lead (red) 8 This model is equipped with a VRLA (Valve Regulated Lead Acid) battery. There is no need to check the electrolyte or to add distilled water. However, the battery lead connections need to be checked and, if necessary, tightened.
U2C914E0.book Page 33 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT battery, be sure the key is turned to “OFF”, then disconnect the negative lead before disconnecting the positive lead. EAU23664 Replacing the fuses The main fuse is located behind panel C. (See page 8-9.) Fuse box 1 is located behind cowling A. (See page 8-9.) [ECA16302] 2. If the battery will be stored for more than two months, check it at least once a month and fully charge it if necessary. 3.
U2C914E0.book Page 34 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT Fuse box 2 is located behind panel B. (See page 8-9.) 1. 2. 3. 4. 5. 6. 8 Backup fuse (for clock and audio system) Radiator fan fuse Headlight fuse Signaling system fuse Ignition fuse Spare fuse If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage.
U2C914E0.book Page 35 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU24283 Replacing a turn signal light bulb or the tail/brake light bulb 1. Remove the lens by removing the screws. 1. Do not touch the glass part of the bulb. 1. Disconnect the headlight coupler, and then remove the headlight bulb cover. 1. Headlight bulb holder 3. Place a new headlight bulb into position, and then secure it with the bulb holder. 4. Install the headlight bulb cover, and then connect the coupler.
U2C914E0.book Page 36 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT 2. Remove the burnt-out bulb by pushing it in and turning it counterclockwise. 3. Insert a new bulb into the socket, push it in, and then turn it clockwise until it stops. 4. Install the lens by installing the screws. NOTICE: Do not overtighten the screws, otherwise the lens may break.
U2C914E0.book Page 37 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU25871 Troubleshooting Although Yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur during operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and loss of power. The following troubleshooting charts represent quick and easy procedures for checking these vital systems yourself.
U2C914E0.book Page 38 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU42311 Troubleshooting charts Starting problems or poor engine performance 1. Fuel There is enough fuel. Check the compression. There is no fuel. Supply fuel. There is compression. Check the ignition. There is no compression. Have a Yamaha dealer check the vehicle. Check the fuel level in the fuel tank. The engine does not start. Check the compression. 2. Compression Operate the electric starter. 3.
U2C914E0.book Page 39 Tuesday, July 28, 2009 4:59 PM PERIODIC MAINTENANCE AND ADJUSTMENT Engine overheating EWAT1040 WARNING ● ● Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM MOTORCYCLE CARE AND STORAGE EAU37833 Matte color caution contact with strong or abrasive cleaning products, solvent or thinner, fuel (gasoline), rust removers or inhibitors, brake fluid, antifreeze or electrolyte. EAU26123 Cleaning ECA15192 NOTICE Some models are equipped with matte colored finished parts. Be sure to consult a Yamaha dealer for advice on what products to use before cleaning the vehicle.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM MOTORCYCLE CARE AND STORAGE ● transmission seals, audio system, speakers, saddlebags, travel trunk and electrical parts. Many expensive repair bills have resulted from improper high-pressure washer applications, such as those available at coin-operated car washers. 1. Rinse any dirt and degreaser off with a garden hose, using only enough pressure to do the job. 2.
U2C914E0.book Page 3 Tuesday, July 28, 2009 4:59 PM MOTORCYCLE CARE AND STORAGE EAU26251 Storage Short-term Always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover. ECA10810 NOTICE ● ● 9 Storing the motorcycle in a poorly ventilated room or covering it with a tarp, while it is still wet, will allow water and humidity to seep in and cause rust.
U2C914E0.book Page 4 Tuesday, July 28, 2009 4:59 PM MOTORCYCLE CARE AND STORAGE °C (90 °F)]. For more information on storing the battery, see page 8-32. TIP Make any necessary repairs before storing the motorcycle.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM SPECIFICATIONS Dimensions: Overall length: 2655 mm (104.5 in) Overall width: 900 mm (35.4 in) Overall height: 1565 mm (61.6 in) Seat height: 750 mm (29.5 in) Wheelbase: 1705 mm (67.1 in) Ground clearance: 155 mm (6.10 in) Minimum turning radius: 3500 mm (137.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM SPECIFICATIONS Transmission type: Constant mesh 5-speed Operation: Left foot operation Gear ratio: 1st: 43/17 (2.529) 2nd: 31/19 (1.632) 3rd: 30/25 (1.200) 4th: 24/25 (0.960) 5th: 22/28 (0.786) Chassis: Frame type: Double cradle Caster angle: 29.17 ° Trail: 152.0 mm (5.
U2C914E0.book Page 3 Tuesday, July 28, 2009 4:59 PM SPECIFICATIONS Charging system: AC magneto Battery: Model: YTX20L-BS Voltage, capacity: 12 V, 18.0 Ah Headlight: Bulb type: Halogen bulb Bulb voltage, wattage × quantity: 10 Headlight: 12 V, 60 W/55 W × 1 Tail/brake light: 12 V, 8.0 W/27.0 W × 1 Front turn signal/position light: 12 V, 23 W/8.0 W × 2 Rear turn signal light: 12 V, 21.0 W × 2 Neutral indicator light: 12 V, 1.7 W × 1 High beam indicator light: 12 V, 1.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM CONSUMER INFORMATION EAU26352 Identification numbers EAU26381 Key identification number EAU26400 Vehicle identification number Record the key identification number, vehicle identification number and model label information in the spaces provided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehicle is stolen. KEY IDENTIFICATION NUMBER: VEHICLE IDENTIFICATION NUMBER: 11 1.
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM CONSUMER INFORMATION EAU26470 Model label 11 EAU48270 Vehicle Emission Control Information label 1 1. Model label The model label is affixed to the frame under the rider seat. (See page 4-14.) Record the information on this label in the space provided. This information will be needed when ordering spare parts from a Yamaha dealer. 1.
U2C914E0.book Page 3 Tuesday, July 28, 2009 4:59 PM CONSUMER INFORMATION EAU26551 Reporting safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A.
U2C914E0.
U2C914E0.book Page 5 Tuesday, July 28, 2009 4:59 PM CONSUMER INFORMATION EAU26632 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required. It is not acceptable proof of maintenance work.
U2C914E0.
U2C914E0.book Page 7 Tuesday, July 28, 2009 4:59 PM CONSUMER INFORMATION EAU26703 YAMAHA MOTOR CORPORATION, U.S.A.
U2C914E0.
U2C914E0.
U2C914E0.book Page 1 Tuesday, July 28, 2009 4:59 PM INDEX A Air filter elements, cleaning................... 8-19 Audio settings (basic).............................. 5-4 Audio settings (modes) ........................... 5-6 Audio system .......................................... 5-1 Auxiliary audio source........................... 5-20 Auxiliary DC jack and connector ........... 4-22 Cruise control switches........................... 4-9 Cruise control system .............................
U2C914E0.book Page 2 Tuesday, July 28, 2009 4:59 PM INDEX Sidestand, checking and lubricating ..... 8-29 Sound control unit................................... 5-3 Spark plugs, checking .......................... 8-12 Specifications ....................................... 10-1 Speedometer unit ................................... 4-4 Starter (choke) knob ............................. 4-13 Starting and warming up a cold engine................................................... 7-1 Start switch ...............
A5-yoko_Blank.
A5-yoko_Blank.
YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2009.08-0.
