Read this manual carefully before operating this vehicle.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM EAU10042 Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM INTRODUCTION EAU10083 Congratulations on your purchase of the Yamaha Royal Star™ VENTURE®. This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM IMPORTANT MANUAL INFORMATION EAU10132 Particularly important information is distinguished in this manual by the following notations: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING NOTICE TIP A WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM IMPORTANT MANUAL INFORMATION EAU10193 XVZ13TFSA(C) OWNER’S MANUAL ©2010 by Yamaha Motor Corporation, U.S.A. 1st edition, June 2010 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in Japan.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM TABLE OF CONTENTS LOCATION OF IMPORTANT LABELS .............................................1-1 SAFETY INFORMATION ..................2-1 DESCRIPTION ..................................3-1 Left view ..........................................3-1 Right view ........................................3-2 Controls and instruments.................3-3 INSTRUMENT AND CONTROL FUNCTIONS .......................................4-1 Main switch/steering lock ..............
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM TABLE OF CONTENTS Brake light switches ......................8-25 Checking the front and rear brake pads ..........................................8-26 Checking the brake and clutch fluid levels .................................8-26 Changing the brake and clutch fluids ..........................................8-28 Checking and lubricating the cables ........................................8-28 Checking and lubricating the throttle grip and cable ........
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM LOCATION OF IMPORTANT LABELS EAU10384 1 Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM LOCATION OF IMPORTANT LABELS 1 2 NOTICE Cleaning with alkaline or acid cleaner, gasoline or solvent will damage windshield. Use neutral detergent.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM SAFETY INFORMATION EAU10287 2 Be a Responsible Owner As the vehicle’s owner, you are responsible for the safe and proper operation of your motorcycle. Motorcycles are single-track vehicles. Their safe use and operation are dependent upon the use of proper riding techniques as well as the expertise of the operator. Every operator should know the following requirements before riding this motorcycle.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM SAFETY INFORMATION ● ● due to excessive speed or undercornering (insufficient lean angle for the speed). • Always obey the speed limit and never travel faster than warranted by road and traffic conditions. • Always signal before turning or changing lanes. Make sure that other motorists can see you. The posture of the operator and passenger is important for proper control.
U1BM10E0.book Page 3 Tuesday, June 29, 2010 1:31 PM SAFETY INFORMATION ● ● 2 Do not run engine in poorly ventilated or partially enclosed areas such as barns, garages, or carports. Do not run engine outdoors where engine exhaust can be drawn into a building through openings such as windows and doors. Loading Adding accessories or cargo to your motorcycle can adversely affect stability and handling if the weight distribution of the motorcycle is changed.
U1BM10E0.book Page 4 Tuesday, June 29, 2010 1:31 PM SAFETY INFORMATION Aftermarket Parts, Accessories, and Modifications While you may find aftermarket products similar in design and quality to genuine Yamaha accessories, recognize that some aftermarket accessories or modifications are not suitable because of potential safety hazards to you or others.
U1BM10E0.book Page 5 Tuesday, June 29, 2010 1:31 PM SAFETY INFORMATION ● ● 2 ● ● ● Check that the fuel cock (if equipped) is in the “OFF” position and that there are no fuel leaks. Point the front wheel straight ahead on the trailer or in the truck bed, and choke it in a rail to prevent movement. Shift the transmission in gear (for models with a manual transmission).
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM DESCRIPTION EAU10410 Left view 3 4 5 6,7 8 9 3 2 10 11 1 1. 2. 3. 4. 5. 6. 7. 8. 9. Helmet holder (page 4-15) 10.Tail/brake light (page 8-36) 11.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM DESCRIPTION EAU10420 Right view 2 3 4 5 6 78 9 10 3 11 12 1 13 16 1. 2. 3. 4. 5. 6. 7. 8. 15 14 9. Fuel tank (page 4-10) 10.Front fork air valve (page 4-18) 11.Headlight (page 8-35) 12.Front turn signal/position lights (page 8-36) 13.Fuse box 1 (page 8-33) 14.Brake pedal (page 4-10) 15.Rider footrest 16.
U1BM10E0.book Page 3 Tuesday, June 29, 2010 1:31 PM DESCRIPTION EAU10430 Controls and instruments 3 1. 2. 3. 4. 5. 6. 7. 8. 9.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU10460 Main switch/steering lock EWA10061 WARNING Never turn the key to “OFF” or “LOCK” while the vehicle is moving. Otherwise the electrical systems will be switched off, which may result in loss of control or an accident. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS The key cannot be removed. EAU49391 Indicator lights and warning lights 1. 2. 3. 4. 5. 6. Left turn signal indicator light “ High beam indicator light “ ” Oil level warning light “ ” Overdrive indicator light “O/D” Engine trouble warning light “ Fuel level warning light “ ” ” 1. 2. 3. 4.
U1BM10E0.book Page 3 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU11080 EAU11270 High beam indicator light “ ” This indicator light comes on when the high beam of the headlight is switched on. Fuel level warning light “ ” This warning light comes on when the fuel level drops below approximately 3.5 L (0.92 US gal, 0.77 Imp.gal). When this occurs, turn the fuel cock lever to the “RES” position and refuel as soon as possible.
U1BM10E0.book Page 4 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS self-diagnosis system. (See page 4-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. The warning light should come on for a few seconds, and then go off. If the warning light does not come on initially when the key is turned to “ON”, or if the warning light remains on, have a Yamaha dealer check the electrical circuit.
U1BM10E0.book Page 5 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU11843 TIP After resetting the fuel reserve tripmeter, the display will return to the prior mode. 4 Clock mode To change the display to the clock mode, push the “SELECT” button for at least two seconds. To change the display back to the odometer and tripmeter modes, push the “SELECT” button. To set the clock 1. Push both the “SELECT” and “RESET” buttons for at least two seconds. 2.
U1BM10E0.book Page 6 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS grip is released. However, if the speed is increased by more than 8 km/h (5 mi/h), the cruise control system will be deactivated until the traveling speed is within 8 km/h (5 mi/h) of the set speed. 1. Cruise control switch 2. “CANCEL” switch 2. Press the “SET/DEC” (set/decelerate) side of the cruise control switch to activate the cruise control system. The “SET” indicator light comes on. 3.
U1BM10E0.book Page 7 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS then go off. Once the cruise control system is reactivated, the “SET” indicator light will come on. Push the “CRUISE” switch to the right to turn the cruise control system off completely. EWA11071 WARNING 4 If the cruise control system is not working correctly, the “SET” and “RES” indicator lights will flash simultaneously. If this occurs, turn the cruise control system off and have a Yamaha dealer check it.
U1BM10E0.book Page 8 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS Right 1. 2. 3. 4. Engine stop switch “ Hazard switch “ ” Cruise control switch Start switch “ ” / ” EAU12390 “TALK” switch See page 5-16 for an explanation of the CB radio. EAU12400 Dimmer switch “ / ” Set this switch to “ ” for the high beam and to “ ” for the low beam. EAU12430 EAU12660 Turn signal switch “ / ” To signal a right-hand turn, push this switch to “ ”.
U1BM10E0.book Page 9 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS The hazard lights are used in case of an emergency or to warn other drivers when your vehicle is stopped where it might be a traffic hazard. EAU12820 EAU12881 Clutch lever Shift pedal 1. Clutch lever 1. Shift pedal 2. Neutral position ECA10061 NOTICE Do not use the hazard lights for an extended length of time with the engine not running, otherwise the battery may discharge.
U1BM10E0.book Page 10 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU12890 EAU12941 EAU13121 Brake lever Brake pedal Fuel tank cap 1. Brake lever 1. Brake pedal The brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handlebar grip. The brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal. 1. Fuel tank cap lock cover 2. Unlock.
U1BM10E0.book Page 11 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU13212 TIP The fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked. EWA10131 WARNING 4 Make sure that the fuel tank cap is properly installed before riding. Leaking fuel is a fire hazard. Fuel Make sure there is sufficient gasoline in the tank. EWA10881 WARNING Gasoline and gasoline vapors are extremely flammable.
U1BM10E0.book Page 12 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS ately. If gasoline spills on your skin, wash with soap and water. If gasoline spills on your clothing, change your clothes. EAU13373 Recommended fuel: Unleaded gasoline only Fuel tank capacity: 22.5 L (5.94 US gal, 4.95 Imp.gal) Fuel reserve amount (when the fuel level warning light comes on): 3.5 L (0.92 US gal, 0.77 Imp.gal) um unleaded fuel.
U1BM10E0.book Page 13 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU13550 Fuel cock This indicates reserve. With the fuel cock lever in this position, the fuel reserve is made available. Turn the fuel cock lever to this position if you run out of fuel while riding. When this occurs, refuel as soon as possible and be sure to turn the fuel cock lever back to “ON”! ON The fuel cock supplies fuel from the tank to the carburetors while also filtering it.
U1BM10E0.book Page 14 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU13600 Starter (choke) knob “ ” EAU13780 Locking the steering with a padlock EAU14240 Rider seat To remove the rider seat Remove the nuts, and then pull the rider seat up. 4 1. Starter (choke) knob “ ” Starting a cold engine requires a richer air-fuel mixture, which is supplied by the starter (choke). Move the knob in direction (a) to turn on the starter (choke).
U1BM10E0.book Page 15 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU50730 Helmet holders There is a helmet holder on each side of the travel trunk. To open a helmet holder Insert the key into the helmet holder lock, and then turn it as shown. 4 1. Projection 2. Seat holder 1. Helmet holder (left) 2. Unlock. TIP Make sure that the rider seat is properly secured before riding. To close a helmet holder Place the helmet holder in the original position, and then remove the key.
U1BM10E0.book Page 16 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU14633 Sidecases and travel trunk EWA11082 WARNING Improper loading or overloading can cause loss of control and possibly an accident or personal injury. See pages 2-1 and 8-22 for important loading and tire pressure information. ● Always securely close the sidecases and travel trunk before riding. ● Distribute weight evenly on each side of the motorcycle.
U1BM10E0.book Page 17 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS To close the travel trunk 1. Fold the travel trunk lid up completely, and then fold it down. 4 1. Travel trunk lock 2. Unlock. 2. Fold the travel trunk lid up, and then release it so that it will rest in place as shown. NOTICE: Do not apply excessive pressure on the travel trunk lid when it is open. TIP Push both sides of the lid down so that both latches snap into place. [ECA10911] 1.
U1BM10E0.book Page 18 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU14655 Spring rate: Minimum (soft): Air pressure = 0 kPa (0 kgf/cm², 0 psi) Standard: Air pressure = 0 kPa (0 kgf/cm², 0 psi) Maximum (hard): Air pressure = 50 kPa (0.5 kgf/cm², 7.1 psi) Adjusting the front fork EWA10180 WARNING Always adjust both fork legs equally, otherwise poor handling and loss of stability may result. This front fork is equipped with air valves for adjusting the spring rate.
U1BM10E0.book Page 19 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU14803 Spring rate: Minimum (soft): Air pressure = 0 kPa (0 kgf/cm², 0 psi) Standard: Air pressure = 0 kPa (0 kgf/cm², 0 psi) Maximum (hard): Air pressure = 400 kPa (4.0 kgf/cm², 57 psi) Adjusting the shock absorber assembly This shock absorber assembly is equipped with an air valve for adjusting the spring rate. ECA11090 NOTICE 4 Never exceed the maximum air pressure, otherwise the oil seal may become damaged.
U1BM10E0.book Page 20 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU15304 Sidestand The sidestand is located on the left side of the frame. Raise the sidestand or lower it with your foot while holding the vehicle upright. this system regularly and have a Yamaha dealer repair it if it does not function properly. TIP The built-in sidestand switch is part of the ignition circuit cut-off system, which cuts the ignition in certain situations.
U1BM10E0.book Page 21 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS With the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “ 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? YES 4 WARNING If a malfunction is noted, have a Yamaha dealer check the system before riding. ”. NO The neutral switch may not be working correctly.
U1BM10E0.book Page 22 Tuesday, June 29, 2010 1:31 PM INSTRUMENT AND CONTROL FUNCTIONS EAU15415 Auxiliary DC jack and connector ECA11032 NOTICE The accessories connected to the auxiliary DC jack and connector should not be used with the engine turned off, and their combined load must never exceed 5 A or 60 W, otherwise the fuse may blow or the battery may discharge. 1.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO EAU15440 Location of parts 5 1. 2. 3. 4. 5. 6. Audio system/CB radio control unit Front speaker Rider headset jack Cassette deck lid Main switch/steering lock Eject (“ ”) button 7. Cassette deck compartment 8. Auxiliary audio input jack 9. Rear speaker 10.Passenger volume control knob 11.Passenger “TALK” button 12.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO EWA11370 ● ● EAU15450 Headsets (optional) WARNING It is dangerous to operate the audio system controls while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. dealer if you wish to obtain headsets. Connect the headsets to the jacks shown in the illustrations and make sure that the headsets are selected as the output.
U1BM10E0.book Page 3 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO EAU15462 Control unit 5 1. 2. 3. 4. 5. Volume control knob Up/down (“ ”) switch Audio system button “AUDIO” Selection button “SELECT” CB radio button “CB” Volume control knob This knob adjusts the audio system volume, the CB radio reception volume, and the CB squelch level. Up/down (“ ”) switch This switch is used to perform the following operations.
U1BM10E0.book Page 4 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO CB Radio SP/HS (Output) EAU15480 Making basic settings IC (Intercom volume) Adjusting the audio system volume Turning on/off the audio system RB: on/oF (Roger beep) ● Programming preset radio stations Long push (two seconds or more) ● Selecting the preset radio station programming mode CB radio button “CB” This button is used to perform the following operations.
U1BM10E0.book Page 5 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO Turning on/off the CB radio be set between “0” and “20”. After the adjustment is made, the CB radio returns to normal operation and the CB channel appears in the display. EAU15502 Making mode settings General procedure The following setting procedure applies to the audio system, CB radio, and optional CD changer. TIP ● 1. CB radio indicator light 5 To turn the power on 1.
U1BM10E0.book Page 6 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO Audio system SP/HS (Output) Radio frequency 2 BASS TREB (Treble) AV (Auto volume) FAD (Fade1) Selecting the output (speakers or headsets) Adjusting the bass level IC (Intercom volume) 1 This mode does not appear in the display when 2 the headsets are selected as the output. This mode appears in the display only when one of the radio frequency bands is selected as the audio source.
U1BM10E0.book Page 7 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO Adjusting the treble level Adjusting the fade level (balance between front and rear speakers) TIP When the fade level is set to “0”, the front and rear speaker levels are the same. Adjusting the intercom volume 5 1. Repeatedly push the “SELECT” button for less than one second until “TREB” appears at the bottom of the display. 2.
U1BM10E0.book Page 8 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO Adjusting the auto volume When riding the vehicle, external noise may override the audio system output volume. The audio system features an automatic volume control function which compensates for external noise. 1. Repeatedly push the “SELECT” button for less than one second until the auto volume (e.g., “AV: 3”) appears in the display. 2.
U1BM10E0.book Page 9 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO EWA11380 WARNING ● ● It is dangerous to operate the cassette deck while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. ● To clean the tape head, use a de-magnetizing cleaning cassette, but be sure to turn the volume all the way down to avoid speaker damage.
U1BM10E0.book Page 10 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO Changing the tape play direction TIP ● ● The maximum number of songs that can be skipped in either direction is 9. To stop skipping songs, push the up/down switch in the opposite direction that songs are being skipped. Turning on/off the Dolby noise reduction system Skipping a blank While the cassette tape is playing, push either side of the up/down switch for more than one second to reverse the play direction.
U1BM10E0.book Page 11 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO Ejecting the cassette tape EAU15533 EWA11390 Radio operation WARNING ● ● 1. Eject (“ ● ”) button 1. Radio antenna 5 Push the eject (“ ”) button to eject the tape from the cassette deck. “EJCT” appears in the display, and then “CASS” starts flashing. It is dangerous to operate the radio while riding. Never take your hands off the handlebars while riding.
U1BM10E0.book Page 12 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO Selecting a frequency band FM1 FM2 FM3 AM (Tape) AUX (Auxiliary audio source) (CD changer*) tunes in the first station that has a strong enough signal to be received. Tuning in a radio station manually * The CD mode appears in the display only when the optional CD changer is installed. Tuning in a radio station automatically 1. Frequency band This radio offers three FM bands and one AM band.
U1BM10E0.book Page 13 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO played. The frequency changes in 0.2-MHz steps for FM and in 10kHz steps for AM. Programming preset radio stations manually Tuning in a preset radio station 3. Repeatedly push either side of the up/down switch for less than one second until the desired preset number (“1” through “6”) is displayed. TIP Selecting “A” will automatically program the preset stations. See the following section. 5 1. Preset station number 1.
U1BM10E0.book Page 14 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO 3. Push either side of the up/down switch once for one second or more to tune in a station automatically. 4. Repeatedly push either side of the up/down switch for less than one second until the desired preset number (“1” through “6”) is displayed. 5. Push the “SELECT” button once for less than one second to store the radio station selected in step 3 under the preset number selected in step 4. 6.
U1BM10E0.book Page 15 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO EAU15540 Optional CD changer operation EWA11400 WARNING ● ● 5 It is dangerous to operate the CD changer while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. 1. Insert up to six CDs into the CD changer. Follow the manufacturer’s directions. 2.
U1BM10E0.book Page 16 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO EAU15551 EWA11410 CB radio operation WARNING ● ● 1. CB antenna ● It is dangerous to change CB radio channels or adjust the volume while riding. Never take your hands off the handlebars while riding. Keep the volume at a low enough level to be aware of traffic conditions and ensure safety. Never ride the motorcycle with the CB antenna folded down. TIP Lift the sleeve to fold down the antenna. 1.
U1BM10E0.book Page 17 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO lessening of the operating privileges or responsibilities of CB users. An operator of a CB radio station is still required to comply with the Communications Act and with the rules of CB Radio Service.
U1BM10E0.book Page 18 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO returns to normal operation and the CB channel appears in the display. For maximum reception sensitivity, the squelch level should be set by turning the control knob fully counterclockwise, and then slowly turning it clockwise until the background noise has been sufficiently reduced. In order for an incoming CB signal to be heard, it must be stronger than the noise received.
U1BM10E0.book Page 19 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO Channel information 5 Channel Channel Frequency in MHz Channel Channel Frequency in MHz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 26.965 26.975 36.985 27.005 27.015 27.025 27.035 27.055 27.065 27.075 27.085 27.105 27.115 27.125 27.135 27.155 27.165 27.175 27.185 27.205 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 27.215 27.225 27.235 27.245 27.255 27.265 27.275 27.285 27.295 27.305 27.315 27.
U1BM10E0.book Page 20 Tuesday, June 29, 2010 1:31 PM AUDIO SYSTEM AND CB RADIO Transmitting and receiving EAU15570 Auxiliary audio source operation Transmission Push the rider “TALK” switch or the passenger “TALK” button to transmit. “TX” appears in the display. Auxiliary audio equipment can be connected to, and played through, the audio system. 1. Insert the output plug of the auxiliary equipment into the jack located at the right of the cassette deck.
U1BM10E0.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM FOR YOUR SAFETY – PRE-OPERATION CHECKS EAU15596 Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the Owner’s Manual. EWA11151 WARNING Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage. Do not operate the vehicle if you find any problem.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM FOR YOUR SAFETY – PRE-OPERATION CHECKS ITEM CHECKS PAGE Front brake • • • • • • • • • Check operation. If soft or spongy, have Yamaha dealer bleed hydraulic system. Check lever free play. Adjust if necessary. Check brake pads for wear. Replace if necessary. Check fluid level in reservoir. If necessary, add recommended brake fluid to specified level. Check hydraulic system for leakage. 8-25, 8-26, 8-26 Rear brake • • • • • • • Check operation.
U1BM10E0.book Page 3 Tuesday, June 29, 2010 1:31 PM FOR YOUR SAFETY – PRE-OPERATION CHECKS ITEM CHECKS PAGE Brake and clutch levers • Make sure that operation is smooth. • Lubricate lever pivoting points if necessary. 8-29 Sidestand • Make sure that operation is smooth. • Lubricate pivot if necessary. 8-30 Chassis fasteners • Make sure that all nuts, bolts and screws are properly tightened. • Tighten if necessary. — Instruments, lights, signals and switches • Check operation.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM OPERATION AND IMPORTANT RIDING POINTS EAU15951 Read the Owner’s Manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your Yamaha dealer. EWA10271 WARNING Failure to familiarize yourself with the controls can lead to loss of control, which could cause an accident or injury.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM OPERATION AND IMPORTANT RIDING POINTS er than necessary. The time necessary for starter (choke) use depends upon the ambient temperature. Temperatures above 10 °C (50 °F) require about 7 seconds of starter (choke) use and temperatures below 10 °C (50 °F) require about 35 seconds with the starter (choke) turned on, then about 2.5 minutes with the starter (choke) in the halfway position.
U1BM10E0.book Page 3 Tuesday, June 29, 2010 1:31 PM OPERATION AND IMPORTANT RIDING POINTS ECA10260 NOTICE ● ● 7 Even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long distances. The transmission is properly lubricated only when the engine is running. Inadequate lubrication may damage the transmission.
U1BM10E0.book Page 4 Tuesday, June 29, 2010 1:31 PM OPERATION AND IMPORTANT RIDING POINTS EAU16841 Engine break-in There is never a more important period in the life of your engine than the period between 0 and 1600 km (1000 mi). For this reason, you should read the following material carefully. Since the engine is brand new, do not put an excessive load on it for the first 1600 km (1000 mi). The various parts in the engine wear and polish themselves to the correct operating clearances.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU17243 EWA15121 EAU17302 WARNING Periodic inspection, adjustment, and lubrication will keep your vehicle in the safest and most efficient condition possible. Safety is an obligation of the vehicle owner/operator. The most important points of vehicle inspection, adjustment, and lubrication are explained on the following pages.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU17412 Owner’s tool kit 1. Owner’s tool kit The owner’s tool kit is located inside the right sidecase. (See page 4-16.) The service information included in this manual and the tools provided in the owner’s tool kit are intended to assist you in the performance of preventive maintenance and minor repairs.
U1BM10E0.book Page 3 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU48490 TIP ● ● From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months. Items marked with an asterisk require special tools, data and technical skills, have a Yamaha dealer perform the service. EAU17601 Periodic maintenance chart for the emission control system INITIAL No. 8 ITEM ROUTINE 1 * Fuel line • Check fuel hoses for cracks or damage.
U1BM10E0.book Page 4 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ITEM ROUTINE 7 * Idle speed • Check and adjust engine idle speed. 8 * Exhaust system • Check for leakage. • Tighten if necessary. • Replace gasket(s) if necessary. 9 * Evaporative emission control system (for California only) • Check control system for damage. • Replace if necessary.
U1BM10E0.book Page 5 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU32186 General maintenance and lubrication chart INITIAL No. ITEM ROUTINE 1 * Air filter elements • Clean with compressed air. • Replace if necessary. 2 * Clutch • Check operation and fluid leakage. • Correct if necessary.
U1BM10E0.book Page 6 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ITEM ROUTINE Swingarm pivot bearings • Check bearing assemblies for looseness. • Moderately repack with lithiumsoap-based grease. 10 * Steering bearings • Check bearing assemblies for looseness. • Moderately repack with lithiumsoap-based grease every 16000 mi (25000 km) or 24 months.
U1BM10E0.book Page 7 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ITEM ROUTINE 600 mi (1000 km) or 1 month ODOMETER READINGS 4000 mi (7000 km) or 6 months 8000 mi 12000 mi 16000 mi 20000 mi (13000 km) (19000 km) (25000 km) (31000 km) or or or or 12 months 18 months 24 months 30 months 18 * Front fork • Check operation and for oil leakage. • Replace if necessary. √ √ √ √ √ 19 * Shock absorber assembly • Check operation and for oil leakage.
U1BM10E0.book Page 8 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ITEM ROUTINE 27 * Throttle grip • Check operation. • Check throttle grip free play, and adjust if necessary. • Lubricate cable and grip housing. 28 * Lights, signals and switches • Check operation. • Adjust headlight beam.
U1BM10E0.book Page 9 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU18712 Removing and installing cowlings and panels The cowlings and panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a cowling or panel needs to be removed and installed. 1. Cowling B 2. Panel B 3. Panel C 1. Cowling A 2. Bolt 3. Quick fastener screw EAU35841 Cowling A 8 1. Cowling A 2. Panel A To remove the cowling 1.
U1BM10E0.book Page 10 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT TIP Make sure that the projection fits into the grommet. 2. Install cowling A. EAU35861 Panels A and B 1. Grommet 2. Projection 3. Cowling A To remove a panel Remove the bolt, and then pull the panel off as shown. 1. Cowling B 2. Bolt TIP Make sure that the projection fits into the grommet. EAU35850 Cowling B To remove the cowling 1. Remove cowling A. 2. Remove the bolts, and then pull the cowling off as shown.
U1BM10E0.book Page 11 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT 2 1 3 4 1. Panel B 2. Bolt To install a panel Place the panel in the original position, and then install the bolt. EAU19333 Panel C To remove the panel 1. Remove panel B. 2. Remove the left passenger footrest by removing the bolts. 3. Remove the screw, and then pull the panel off as shown. 1. 2. 3. 4. Panel C Screw Bolt Passenger footrest To install the panel 1.
U1BM10E0.book Page 12 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT 3. Install panel B. EAU19545 Checking the spark plugs The spark plugs are important engine components, which are easy to check. Since heat and deposits will cause any spark plug to slowly erode, the spark plugs should be removed and checked in accordance with the periodic maintenance and lubrication chart. In addition, the condition of the spark plugs can reveal the condition of the engine. To remove a spark plug 1.
U1BM10E0.book Page 13 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT 3. Check each spark plug for electrode erosion and excessive carbon or other deposits, and replace it if necessary. Specified spark plug: NGK/DPR8EA-9 DENSO/X24EPR-U9 4. Measure the spark plug gap with a wire thickness gauge and, if necessary, adjust the gap to specification. To install a spark plug 1.
U1BM10E0.book Page 14 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT 4. Remove the engine oil filler cap, the engine oil drain bolt and its gasket to drain the oil from the crankcase. EAU19908 Engine oil and oil filter cartridge The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter cartridge replaced at the intervals specified in the periodic maintenance and lubrication chart. To check the engine oil level 1.
U1BM10E0.book Page 15 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT TIP Skip steps 5–7 if the oil filter cartridge is not being replaced. 5. Remove the oil filter cartridge with an oil filter wrench. 1. O-ring 1 2 1. Engine oil filter cartridge 2. Oil filter wrench 8 TIP An oil filter wrench is available at a Yamaha dealer. 1. Torque wrench 2. Oil filter wrench TIP Make sure that the O-ring is properly seated. 7.
U1BM10E0.book Page 16 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT Recommended engine oil: See page 10-1. Oil quantity: Without oil filter cartridge replacement: 3.50 L (3.70 US qt, 3.08 Imp.qt) With oil filter cartridge replacement: 3.70 L (3.91 US qt, 3.26 Imp.qt) TIP Be sure to wipe off spilled oil on any parts after the engine and exhaust system have cooled down.
U1BM10E0.book Page 17 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT 2. Remove the final gear oil filler bolt and its gasket, and then check the oil level in the final gear case. TIP The oil level should be at the brim of the filler hole. 1 Tightening torque: Final gear oil filler bolt: 23 Nm (2.3 m·kgf, 17 ft·lbf) To change the final gear oil 1. Place an oil pan under the final gear case to collect the used oil. 2.
U1BM10E0.book Page 18 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU20070 Coolant The coolant level should be checked before each ride. In addition, the coolant must be changed at the intervals specified in the periodic maintenance and lubrication chart. EAU20214 To check the coolant level 1. Place the vehicle on a level surface. 2. Remove panel A. (See page 8-9.) 3. Hold the vehicle in an upright position.
U1BM10E0.book Page 19 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU33031 Changing the coolant The coolant must be changed at the intervals specified in the periodic maintenance and lubrication chart. Have a Yamaha dealer change the coolant. WARNING! Never attempt to remove the radiator cap when the engine is hot.
U1BM10E0.book Page 20 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT 1. Air filter element 2. Screw 6. Lightly tap the air filter element to remove most of the dust and dirt, and then blow the remaining dirt out with compressed air as shown. If the air filter element is damaged, replace it. 7. Install the air filter element by fitting the projection on the air filter element into the holder in the air filter case, then tightening the screws.
U1BM10E0.book Page 21 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU21271 Carburetors The carburetors are important parts of the engine and emission control system, which require very sophisticated adjustment. Therefore, all carburetor adjustments should be left to a Yamaha dealer, who has the necessary professional knowledge and experience.
U1BM10E0.book Page 22 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU21401 EAU32544 Valve clearance Tires The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart.
U1BM10E0.book Page 23 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT Tire inspection EWA10521 WARNING ● 1. Tire sidewall 2. Tire wear indicator 3. Tire tread depth 8 Always check the tires before operating the motorcycle. If a tire tread shows crosswise lines (minimum tread depth), if the tire has a nail or glass fragments in it, or if the sidewall is cracked, contact a Yamaha dealer immediately and have the tire replaced. Minimum tire tread depth (front and rear): 1.0 mm (0.
U1BM10E0.book Page 24 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU21994 EAU22073 Cast wheels To maximize the performance, durability, and safe operation of your vehicle, note the following points regarding the specified wheels. ● The wheel rims should be checked for cracks, bends, warpage or other damage before each ride. If any damage is found, have a Yamaha dealer replace the wheel. Do not attempt even the smallest repair to the wheel.
U1BM10E0.book Page 25 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU22093 Adjusting the brake lever free play 3. Tighten the locknut. WARNING ● ● 1. Locknut 2. Brake lever free play adjusting screw 3. Brake lever free play 8 The brake lever free play should measure 2.0–5.0 mm (0.08–0.20 in) as shown. Periodically check the brake lever free play and, if necessary, adjust it as follows. 1. Loosen the locknut at the brake lever. 2.
U1BM10E0.book Page 26 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU22392 Checking the front and rear brake pads The front and rear brake pads must be checked for wear at the intervals specified in the periodic maintenance and lubrication chart. indicator grooves have almost disappeared, have a Yamaha dealer replace the brake pads as a set. EAU22470 EAU22660 Checking the brake and clutch fluid levels Front brake Rear brake pads EAU22430 Front brake pads 1.
U1BM10E0.book Page 27 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT Clutch ● Use only the recommended quality brake fluid, otherwise the rubber seals may deteriorate, causing leakage and poor braking or clutch performance. Recommended brake and clutch fluid: DOT 4 brake fluid 1. Minimum level mark 8 Insufficient brake or clutch fluid may allow air to enter the brake or clutch systems, possibly causing them to become ineffective.
U1BM10E0.book Page 28 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU22751 EAU23094 EAU49920 Changing the brake and clutch fluids Checking and lubricating the cables Checking and lubricating the throttle grip and cable Have a Yamaha dealer change the brake and clutch fluids at the intervals specified in the TIP after the periodic maintenance and lubrication chart.
U1BM10E0.book Page 29 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU44272 Checking and lubricating the brake and shift pedals EAU43600 Recommended lubricant: Lithium-soap-based grease Checking and lubricating the brake and clutch levers Brake pedal The operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lubricated if necessary.
U1BM10E0.book Page 30 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23202 Checking and lubricating the sidestand EAUM1651 EAU23251 Lubricating the swingarm pivots Lubricating the rear suspension The swingarm pivots must be lubricated by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart.
U1BM10E0.book Page 31 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23272 EAU23283 Checking the front fork Checking the steering The condition and operation of the front fork must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. Worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. 1.
U1BM10E0.book Page 32 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23291 Checking the wheel bearings EAU50580 EWA10760 Battery WARNING ● The front and rear wheel bearings must be checked at the intervals specified in the periodic maintenance and lubrication chart. If there is play in the wheel hub or if the wheel does not turn smoothly, have a Yamaha dealer check the wheel bearings. 1. Battery 2. Negative battery lead (black) 3.
U1BM10E0.book Page 33 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT ● KEEP THIS AND ALL BATTERIES OUT OF THE REACH OF CHILDREN. To charge the battery Have a Yamaha dealer charge the battery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the vehicle is equipped with optional electrical accessories.
U1BM10E0.book Page 34 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT Fuse box 1 is located behind cowling A. (See page 8-9.) Fuse box 2 is located behind panel B. (See page 8-9.) 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6.
U1BM10E0.book Page 35 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23763 Replacing the headlight bulb This model is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. ECA10650 NOTICE 8 Take care not to damage the following parts: ● Headlight bulb Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected.
U1BM10E0.book Page 36 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU24283 Replacing a turn signal light bulb or the tail/brake light bulb 1. Remove the lens by removing the screws. 2. Remove the burnt-out bulb by pushing it in and turning it counterclockwise. 3. Insert a new bulb into the socket, push it in, and then turn it clockwise until it stops. 4. Install the lens by installing the screws. NOTICE: Do not overtighten the screws, otherwise the lens may break.
U1BM10E0.book Page 37 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT a jack either under each side of the frame in front of the rear wheel or under each side of the swingarm. 8 EAU25871 Troubleshooting Although Yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur during operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and loss of power.
U1BM10E0.book Page 38 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU42312 Troubleshooting charts Starting problems or poor engine performance 1. Fuel There is enough fuel. Check the compression. There is no fuel. Supply fuel. There is compression. Check the ignition. There is no compression. Have a Yamaha dealer check the vehicle. Check the fuel level in the fuel tank. The engine does not start. Check the compression. 2. Compression Operate the electric starter. 3.
U1BM10E0.book Page 39 Tuesday, June 29, 2010 1:31 PM PERIODIC MAINTENANCE AND ADJUSTMENT Engine overheating EWAT1040 WARNING ● ● Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM MOTORCYCLE CARE AND STORAGE EAU37833 Matte color caution contact with strong or abrasive cleaning products, solvent or thinner, fuel (gasoline), rust removers or inhibitors, brake fluid, antifreeze or electrolyte. EAU26123 Cleaning ECA15192 NOTICE Some models are equipped with matte colored finished parts. Be sure to consult a Yamaha dealer for advice on what products to use before cleaning the vehicle.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM MOTORCYCLE CARE AND STORAGE ● 9 transmission seals, audio system, speakers, saddlebags, travel trunk and electrical parts. Many expensive repair bills have resulted from improper high-pressure washer applications, such as those available at coin-operated car washers. 1. Rinse any dirt and degreaser off with a garden hose, using only enough pressure to do the job. 2.
U1BM10E0.book Page 3 Tuesday, June 29, 2010 1:31 PM MOTORCYCLE CARE AND STORAGE EAU26252 Storage Short-term Always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover. Be sure the engine and the exhaust system are cool before covering the motorcycle. ECA10810 NOTICE ● ● Storing the motorcycle in a poorly ventilated room or covering it with a tarp, while it is still wet, will allow water and humidity to seep in and cause rust.
U1BM10E0.book Page 4 Tuesday, June 29, 2010 1:31 PM MOTORCYCLE CARE AND STORAGE cessively cold or warm place [less than 0 °C (30 °F) or more than 30 °C (90 °F)]. For more information on storing the battery, see page 8-32. TIP Make any necessary repairs before storing the motorcycle.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM SPECIFICATIONS Dimensions: Overall length: 2655 mm (104.5 in) Overall width: 900 mm (35.4 in) Overall height: 1565 mm (61.6 in) Seat height: 750 mm (29.5 in) Wheelbase: 1705 mm (67.1 in) Ground clearance: 155 mm (6.10 in) Minimum turning radius: 3500 mm (137.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM SPECIFICATIONS Operation: Left foot operation Gear ratio: 1st: 43/17 (2.529) 2nd: 31/19 (1.632) 3rd: 30/25 (1.200) 4th: 24/25 (0.960) 5th: 22/28 (0.786) Chassis: Frame type: Double cradle Caster angle: 29.17 ° Trail: 152.0 mm (5.
U1BM10E0.book Page 3 Tuesday, June 29, 2010 1:31 PM SPECIFICATIONS Battery: Model: YTX20L-BS Voltage, capacity: 12 V, 18.0 Ah Headlight: Bulb type: Halogen bulb Bulb voltage, wattage × quantity: Headlight: 12 V, 60 W/55 W × 1 Tail/brake light: 12 V, 8.0 W/27.0 W × 1 Front turn signal/position light: 12 V, 23 W/8.0 W × 2 Rear turn signal light: 12 V, 21.0 W × 2 Neutral indicator light: 12 V, 1.7 W × 1 High beam indicator light: 12 V, 1.7 W × 1 Oil level warning light: 12 V, 1.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM CONSUMER INFORMATION EAU26352 Identification numbers 11 EAU26381 EAU26400 Key identification number Vehicle identification number 1. Key identification number 1. Vehicle identification number The key identification number is stamped into the key tag. Record this number in the space provided and use it for reference when ordering a new key. The vehicle identification number is stamped into the steering head pipe.
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM CONSUMER INFORMATION EAU26470 Model label EAU48270 Vehicle Emission Control Information label 1 1. Model label The model label is affixed to the frame under the rider seat. (See page 4-14.) Record the information on this label in the space provided. This information will be needed when ordering spare parts from a Yamaha dealer. 1.
U1BM10E0.book Page 3 Tuesday, June 29, 2010 1:31 PM CONSUMER INFORMATION EAU26551 Reporting safety defects 11 If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A.
U1BM10E0.
U1BM10E0.book Page 5 Tuesday, June 29, 2010 1:31 PM CONSUMER INFORMATION EAU26632 Maintenance record 11 Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required. It is not acceptable proof of maintenance work.
U1BM10E0.
U1BM10E0.book Page 7 Tuesday, June 29, 2010 1:31 PM CONSUMER INFORMATION EAU26703 YAMAHA MOTOR CORPORATION, U.S.A.
U1BM10E0.
U1BM10E0.
U1BM10E0.book Page 1 Tuesday, June 29, 2010 1:31 PM INDEX A Air filter elements, cleaning .................. 8-19 Audio settings (basic) ............................. 5-4 Audio settings (modes)........................... 5-5 Audio system .......................................... 5-1 Auxiliary audio source .......................... 5-20 Auxiliary DC jack and connector........... 4-22 Cruise control switches ...........................4-9 Cruise control system..............................
U1BM10E0.book Page 2 Tuesday, June 29, 2010 1:31 PM INDEX Sidestand, checking and lubricating ..... 8-30 Sound control unit ................................... 5-3 Spark plugs, checking........................... 8-12 Specifications........................................ 10-1 Speedometer unit.................................... 4-4 Starter (choke) knob ............................. 4-14 Starting and warming up a cold engine... 7-1 Start switch .............................................
U1BM10E0.
YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2010.07-0.
