Operation Manual

PLAY-SETUP
108 Chapter 4 PLAY Mode • A5000/A4000 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
Knob 5
[ Turn] AD Input-R Pan (A/D Input Right Pan)
Specifies the output pan position of the signal received
via the "R" A/D input jack.
[Range] -63 — +63
Positive values set pan to the right; negative val-
ues set pan to the left.
• When "L/R" or "L+R" is selected as the AD Input
Source, the ADInput-Lpan setting applies to both
channels and thus the ADInput-Rpan parameter can-
not be edited.
[ Press] QUICK...
Calls the quick entry menu (page 83).
Knob 1
Same function as Cursor q (page 107).
Knob 2
[ Turn] ADInput-L Output1 (A/D Input Left Output 1)
Sets the output destination of the signal received at the
"L" A/D input jack.
[Range] off, StereoOut, AsgnOutL&R, AsgnOut1&2,
AsgnOut3&4, AsgnOut5&6, DIG&OPT, Ef1 — Ef6
(Ef1 — Ef3 on the A4000)
• StereoOut ... Output is sent to the rear-panel STE-
REO OUT jacks as well as the front-panel
PHONES jack.
• AsgnOutL&R ... The rear-panel assignable output
jacks.
• AsgnOut1&2, AsgnOut3&4, AsgnOut5&6 ... The
corresponding assignable outputs on the
optional AIEB1 I/O expansion board.
• DIG&OPT ... The coaxial and optical digital outputs
on the optional AIEB1 I/O expansion board.
• Ef1 — Ef6 ... Output is routed to the specified
effect.
Knob 3
[ Turn] ADInput-L Output Level1
(A/D Input Left Output Level 1)
Sets the level of the signal sent to the output destination
specified by the ADInput-LOutput1 parameter.
[Range] 0 — 127
[ Press] QUICK...
Calls the quick entry menu (page 83).
• When both the Output1 and Output 2 parameters are
set to the same output destination, the higher of the
two output level settings (Output Level 1 and Output
Level2) will take priority.
Knob 4
[ Turn] ADInput-L Output2 (A/D Input Left Output 2)
Sets the output destination of the signal received at the
"L" A/D input jack.
[Range] off, StereoOut, AsgnOutL&R, AsgnOut1&2,
AsgnOut3&4, AsgnOut5&6, DIG&OPT, Ef1 — Ef6
(Ef1 — Ef3 on the A4000)
The settings are the same as for the ADInput-L
Output1 parameter (page 108).
Knob 5
[ Turn] ADInput-L Output Level2
(A/D Input Left Output Level 2)
Sets the level of the signal sent to the output destination
specified by the ADInput-L Output2 parameter.
[Range] 0 — 127
[ Press] QUICK...
Calls the quick entry menu (page 83).
• When both the Output1 and Output 2 parameters are
set to the same output destination, the higher of the
two output level settings (Output Level 1 and Output
Level2) will take priority.
Knob 1
Same function as Cursor q (page 107).
Cursor w
Knob 1 Knob 2 Knob 3 Knob 4 Knob 5
Turn
action
Cursor/Page
ADInput-L
Output1
ADInput-L
Output Level1
ADInput-L
Output2
ADInput-L
Output Level2
Press
action
Tree View — QUICK... — QUICK...
w
Cursor
Cursor e
Knob 1 Knob 2 Knob 3 Knob 4 Knob 5
Turn
action
Cursor/Page
ADInput-R
Output1
ADInput-R
Output Level1
ADInput-R
Output2
ADInput-R
Output Level2
Press
action
Tree View — QUICK... — QUICK...
e
Cursor