Operation Manual

PLAY-CONTROL
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● A5000/A4000 • Chapter 4 PLAY Mode 111
[Range]
Function Control Target Page
----- —
EF1-1 — 16 Effect 1 parameters 1 — 16 105
EF1:Output Level Effect 1 output level 105
EF1:Pan Effect 1 pan 105
EF1:Width Effect 1 width 105
EF2-1 — 16 Effect 2 parameters 1 — 16 105
EF2:Output Level Effect 2 output level 105
EF2:Pan Effect 2 pan 105
EF2:Width Effect 2 width 105
EF3-1 — 16 Effect 3 parameters 1 — 16 105
EF3:Output Level Effect 3 output level 105
EF3:Pan Effect 3 pan 105
EF3:Width Effect 3 width 105
Program Level Program volume 90
S/H Speed Sample-and-hold speed 107
Portament Rate/Time Portamento rate/time 92
AD Pan L&R A/D input L&R pan 107
AD Pan L A/D input L pan 107
AD Pan R A/D input R pan 107
AD Level L&R A/D input L&R output level
AD Level L A/D input L output level
AD Level R A/D input R output level
Control1 Range Controller 1 range 111
Control2 Range Controller 2 range 111
Control3 Range Controller 3 range 111
Control4 Range Controller 4 range 111
Program LFO Depth Program LFO depth
EF4-1 — 16 Effect 4 parameters 1 — 16 105
EF4:Output Level Effect 4 output level 105
EF4:Pan Effect 4 pan 105
EF4:Width Effect 4 width 105
EF5-1 — 16 Effect 5 parameters 1 — 16 105
EF5:Output Level Effect 5 output level 105
EF5:Pan Effect 5 pan 105
EF5:Width Effect 5 width 105
EF6-1 — 16 Effect 6 parameters 1 — 16 105
EF6:Output Level Effect 6 output level 105
EF6:Pan Effect 6 pan 105
EF6:Width Effect 6 width 105
(Functions relating to Ef4 — Ef6 cannot be selected on the
A4000)
• Depending on the effect parameter, non-controllable
functions will appear as "---."
• Some parameters may produce noise when con-
trolled.
[ Press] LIST...
Shows a list of the available functions.
Knob 4
[ Turn] Range
Sets the maximum offset that the controller can apply to
the target parameter. This also determines how sensitive
the parameter is to changes in the controller position.
[Range] -63 — +63
When set to "0" the controller will have no
effect. The higher the value the greater the con-
trol range. Negative values revers the control
"direction."
[ Press] QUICK...
Calls the quick entry menu (page 83).
Knob 5
[ Turn] Type
The setting determines how the A5000/A4000 converts
and applies the control-change value received from the
controller.
When you move a controller at a MIDI device, the control-
ler transmits a control-change value indicating the magni-
tude of the movement. The transmitted values always
range from 0 to 127.
[Range] +offset, -/+offset, +offset(-exp), +offset(+exp)
• +offset ... The A5000/A4000 converts the received
value (0 to 127) to a corresponding value in
the range {0 to range}, and adds the result to
the target parameter. Notice that the resulting
offset is therefore always positive (or always
negative, depending on the Range sign; see
below). In other words, the controller can off-
set the target parameter in one direction only.
• -/+offset ... The A5000/A4000 converts the
received value (0 to 127) to a corresponding
value in the range {-range to 0 to +range}, and
adds the result to the target parameter. Notice
that in this case the controller applies 0 offset
when at its center position; displacement in
one direction generates a negative offset,
while displacement in the other generates a
positive offset.
• +offset(-exp) ... The received value (0 — 127) is
converted to an appropriate value within the
available range. The conversion is not linear,
however, with greater variation produced at
lower values and less variation produced at
higher values.
• +offset(+exp) ... The received value (0 — 127) is
converted to an appropriate value within the
available range. The conversion is not linear,
however, with smaller variation produced at
lower values and greater variation produced at
higher values.