Operation Manual

DISK-PROGRAM
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● A5000/A4000 • Chapter 7 DISK Mode 167
1. PROGRAM
PROGRAM allows programs to be loaded into the sampler’s
memory from floppy disk, hard disk, or other media to which
they have been saved.
• See “7. DISK COMMANDS” on page 177 for more information on
disks, partitions, and volumes.
Press the [DISK] button and then the [F1] button to go to the
PROGRAM display.
1 display page is provided: PgmLoad (Program Load).
• The capacity of the wave memory may be exceeded when loading
a number of voices. We recommend installing SIMM expansion
memory to avoid this problem.
PgmLoad
[DISK] Button → [F1]Button → to select "DISK-Pgmload"
Use this page to select and load one or all programs, together
with all samples used by these programs.
Knob 1
[ Turn] Cursor
Positions the cursor.
[ Press] Tree View
Calls the Tree View display (page 83).
Knob 2
[ Turn] Disk
Selects the floppy disk, hard disk, or other storage media
from which a program is to be loaded. When a disk is
selected, all volumes it contains are listed below the disk
name, and all programs contained in the selected volume
are listed on the right side of the display. When a hard
disk, CD-ROM drive or similar storage device is selected,
the SCSI ID number or IDE M/S (Master/Slave) status of
the device is shown to the right of the disk name.
[Range] All installed/connected disks.
• If a connected SCSI device cannot be selected, go
to the disk select display (DISK-DISK-Disk) and
check the mount/unmount status and SCSI ID set-
tings of the device (page 173).
Knob 4
[ Turn] Program
Selects the program to be loaded.
Programs cannot be selected if a non-native disk or a
multi-segment floppy disk is selected.
[Range] 001 — 128
[ Press] LOAD
Initiates loading of the selected program (as well as all
samples used by the program) to the target program
number. An existing program with the same program
number will be overwritten. A confirmation display will
appear when the knob is pressed. Press Knob 5 (>YES)
to actually execute the load operation.
If a sample with the same name as one being loaded
exists in memory a different display will appear (see page
170).
• A program existing in the target program number will
be erased and overwritten by the newly loaded pro-
gram, but samples and sample banks used by the
replaced program will remain in memory.
Knob 5
[ Press] LOAD ALL
All programs in the currently selected volume and their
samples and sample banks will be loaded into the corre-
sponding program numbers. Previously exisiting pro-
grams in those program numbers will be erased and
replaced by the new programs. When the knob is pressed
a confirmation display will appear. Press Knob 5 (>YES)
to actually execute the load operation.
• A program existing in the target program number will
be erased and overwritten by the newly loaded pro-
gram, but samples and sample banks used by the
replaced program will remain in memory.
Knob 1
Same function as Cursor q (page 167).
Knob 2
[ Turn] Volume
Selects the volume containing the program to be loaded.
[Range] All volumes on the selected disk.
• When a volume is selected the program list is
updated to show all the programs in the selected vol-
ume.
Cursor q
Knob 1 Knob 2 Knob 3 Knob 4 Knob 5
Turn
action
Cursor Disk — Program —
Press
action
Tree View — — LOAD LOAD ALL
q
Cursor
Cursor w
Knob 1 Knob 2 Knob 3 Knob 4 Knob 5
Turn
action
Cursor Volume — Program —
Press
action
Tree View — — LOAD LOAD ALL
w
Cursor