Operation Manual

DISK-SEQUENCE
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● A5000/A4000 • Chapter 7 DISK Mode 171
3. SEQUENCE
SEQUENCE allows sequences to be loaded into the sampler’s
memory from floppy disk, hard disk, or other media to which
they have been saved.
Press the [DISK] button and then the [F3] button to go to the
SEQUENCE display.
1 display page is provided: SeqLoad (Sequence Load).
SeqLoad
[DISK] Button → [F3]Button → to select "DISK-SeqLoad"
Use this page to load one or all sequences from disk.
Knob 1
[ Turn] Cursor
Positions the cursor.
[ Press] Tree View
Calls the Tree View display (page 83).
Knob 2
[ Turn] Disk
Selects the floppy disk, hard disk, or other storage media
from which a sequence is to be loaded. When a disk is
selected, all volumes it contains are listed below the disk
name, and all sequences contained in the selected vol-
ume are listed on the right side of the display. When a
hard disk, CD-ROM drive or similar storage device is
selected, the SCSI ID number or IDE M/S (Master/Slave)
status of the device is shown to the right of the disk
name.
[Range] All installed/connected disks.
• If a connected SCSI or IDE device (hard disk, ZIP
drive, etc.) cannot be selected, go to the disk select
display (DISK-DISK-Disk) and check the mount/
unmount status and SCSI ID settings of the device
(page 173).
Knob 3
[ Press] DELETE
Deletes the selected sequence from the disk. A confirma-
tion display will appear when the knob is pressed. Press
Knob 5 (>YES) to actually execute the delete operation.
Knob 4
[ Turn] Sequence
Selects the sequence to be loaded.
Sequences cannot be selected if a non-native disk or a
multi-segment floppy disk is selected.
[Range] All sequences in the selected volume.
[ Press] LOAD
Initiates loading of the selected sequence. A confirmation
display will appear when the knob is pressed. Press Knob
5 (>YES) to actually execute the load operation.
If a sequence with the same name as one being loaded
exists in memory a display allowing you to choose how to
handle the situation will appear (see page 170).
Knob 5
[ Press] LOAD ALL
All sequences in the currently selected volume will be
loaded. When the knob is pressed a confirmation display
will appear. Press Knob 5 (>YES) to actually execute the
load operation.
If a sequence with the same name as one being loaded
exists in memory a display allowing you to choose how to
handle the situation will appear (see page 170).
Knob 1
Same function as Cursor q (page 171).
Knob 2
[ Turn] Volume
Selects the volume containing the sequence to be
loaded.
[Range] All volumes on the selected disk.
• When a volume is selected the sequence list is
updated to show all the sequence in the selected vol-
ume.
Knob 3 — 5
Same function as Cursor q (page 171).
Cursor q
Knob 1 Knob 2 Knob 3 Knob 4 Knob 5
Turn
action
Cursor Disk — Sequence —
Press
action
Tree View — DELETE LOAD LOAD ALL
q
Cursor
Cursor w
Knob 1 Knob 2 Knob 3 Knob 4 Knob 5
Turn
action
Cursor Volume — Sequence —
Press
action
Tree View — DELETE LOAD LOAD ALL
w
Cursor