Operation Manual

Effect Parameter List
262 Appendix • A5000/A4000 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
34: CLIPPER1
1 Drive 0 — 100 Degree of distortion
2 Drive Output Level 0 — 100 Output level
@3 Clip Band Lo, Hi The frequency band to be distorted
4 Cutoff Freq 32Hz — 18.0kHz Distortion band cutoff frequency
5 Clip Type TypeA,TypeB,TypeC,TypeD Type of distortion
Noise may be produced with some voices when the “4. Cutoff Freq” is varied rapidly.
35: CLIPPER2
1 Drive 0 — 100 Degree of distortion
2 Drive Output Level 0 — 100 Output level
@3 Clip Band Lo, Hi, Mid, Lo&Hi Selects the band to be distorted
4 Cutoff Freq 32Hz — 18.0kHz Distortion band cutoff frequency
5 Mid Band Width 1 — 32 Mid, Lo&Hi bandwidth
6 Clip Type TypeA,TypeB,TypeC,TypeD Type of distortion
7 Dry/Wet Balance D63>W — D=W — D<W63 Balance of the dry sound and effect sound
Noise may be produced with some voices when the “4. Cutoff Freq” is varied rapidly.
36: NOISE GATE
1 Threshold -72dB — -30dB Input level at which the gate begins to open
2 Attack 1ms — 40ms Time until when the gate begins to open
3 Release 10ms — 680ms Time until the gate closes
4 Output Level 0 — 127 Output level
37: V-DISTORTION
1 Over Drive 0 — 100% Degree of distortion
@2 Device Transister,Vintage Tube,Dsitortion1,2, Fuzz Specifies the type of distortion
@3 Speaker Type Flat, Stack, Combo,Twin,Radio,Megaphone Speaker simulation type
4 Presence -10 — 10 High frequency control
5 Output Level 0 — 127 Output level
6 Delay Mix 0 — 127 Delay level
7 Delay Time L 0.1ms — 1480.0ms Left channel delay time
8 Delay Time R 0.1ms — 1480.0ms Right channel delay time
9 Feedback Time 0.1ms — 1480.0ms Feedback delay time
10 Feedback Level -63 — +63 Amount of feedback
11 Dry/Wet Balance D63>W — D=W — D<W63 Balance of the dry sound and effect sound
38: DISTORTION, 39: OVERDRIVE
1 Drive 0 — 127 Degree of distortion
2 EQ Low Frequency 32Hz — 2.0kHz Frequency at which the EQ will boost/cut the low range
3 EQ Low Gain -12dB — +12dB Gain with which the EQ will boost/cut the low range
4 LPF Cutoff Freq 1.0kHz — 18.0kHz, thru Frequency at which the filter will cut the high range
5 Output Level 0 — 127 Output level
6 Edge 0 — 127 Curve of distortion characteristics (127: distortion begins suddenly; 0: distortion begins gradually)
7 EQ Mid Frequency 100Hz — 10.0kHz Frequency at which the EQ will boost/cut the mid range
8 EQ Mid Gain -12dB — +12dB Gain with which the EQ will boost/cut the mid range
9 EQ Mid Width 1 — 12.0 Width of the area in which the EQ will boost/cut the mid range
10 Dry/Wet Balance D63>W — D=W — D<W63 Balance between the dry sound and the effect sound
40: AMP SIMULATOR
1 Dry/Wet Balance D63>W — D=W — D<W63 Balance between the dry sound and the effect sound
2 Drive 0 — 127 Degree of distortion
@3 AMP Type Off, Stack, Combo,Tube Select the type of amp to be simulated
4 LPF Cutoff Freq 315Hz — 18.0kHz, thru Frequency at which the low pass filter will cut the high range
5 Edge 0 — 127 Curve of distortion characteristics (127: distortion begins suddenly; 0: distortion begins gradually)
6 Output Level 0 — 127 Output level
41: STEREO DISTORTION, 42: STEREO OVERDRIVE
1 Drive 0 — 127 Degree of distortion
2 EQ Low Frequency 32Hz — 2.0kHz Frequency at which the EQ will boost/cut the low range
3 EQ Low Gain -12dB — +12dB Gain with which the EQ will boost/cut the low range
4 LPF Cutoff Freq 1.0kHz — 18.0kHz, thru Frequency at which the filter will cut the high range
5 Output Level 0 — 127 Output level
6 Edge 0 — 127 Curve of distortion characteristics (127: distortion begins suddenly; 0: distortion begins gradually)
7 EQ Mid Frequency 100Hz — 10.0kHz Frequency at which the EQ will boost/cut the mid range
8 EQ Mid Gain -12dB — +12dB Gain with which the EQ will boost/cut the mid range
9 EQ Mid Width 1 — 12.0 Width of the area in which the EQ will boost/cut the mid range
10 Dry/Wet Balance D63>W — D=W — D<W63 Balance between the dry sound and the effect sound
43: STEREO AMP SIMULATOR
1 Dry/Wet Balance D63>W — D=W — D<W63 Balance between the dry sound and the effect sound
2 Drive 0 — 127 Degree of distortion
@3 AMP Type Off, Stack, Combo,Tube Type of amp simulation
4 LPF Cutoff Freq 315Hz — 18.0kHz, thru Frequency at which the low pass filter will cut the high range
5 Edge 0 — 127 Curve of distortion characteristics (127: distortion begins suddenly; 0: distortion begins gradually)
6 Output Level 0 — 127 Output level
44: DIST + DELAY, 45: OVERDRIVE + DELAY
1 Dist Drive 0 — 127 Degree of distortion
2 Dist Output Level 0 — 127 Output level
3 Dist EQ Low Gain -12dB — +12dB Gain with which the EQ will boost/cut the low range
4 Dist EQ Mid Gain -12dB — +12dB Gain with which the EQ will boost/cut the mid range
5 Delay Mix 0 — 127 Delay level
6 Delay Time L 0.1ms — 1480.0ms Left channel delay time
7 Delay Time R 0.1ms — 1480.0ms Right channel delay time
8 Dly Feedback Time 0.1ms — 1480.0ms Feedback delay time
9 Dly Feedback Level -63 — +63 Amount of feedback
10 Dry/Wet Balance D63>W — D=W — D<W63 Balance between the dry sound and the effect sound