Specifications

Effect Parameter List
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● A5000/A4000 • Appendix 261
23: WAH + DIST + DELAY, 24: WAH + OVERDRIVE + DELAY
1 Wah Sensitive 0 — 127 Sets the wow filter sensitivity to input variation
2 Wah Cutoff Freq Ofst 0 — 127 Offsets the wow filter control frequency
3 Wah Resonance 1 — 12.0 Sets the wah filter bandwidth
4 Wah Release 10ms — 680ms Sets the time before the wow filter center frequency returns to normal
5 Dist Drive 0 — 127 Degree of distortion
6 Dist Output Level 0 — 127 Output level
7 Dist EQ Low Gain -12dB — +12dB Amount of gain by which the EQ will boost/cut the low range
8 Dist EQ Mid Gain -12dB — +12dB Amount of gain by which the EQ will boost/cut the mid range
9 Delay Mix 0 — 127 Delay level
10 Delay Time 0.1ms — 1480.0ms Delay time
11 Dly Feedback Level -63 — +63 Amount of feedback
12 Dry/Wet Balance D63>W — D=W — D<W63 Balance of the dry sound and effect sound
25: TALKING MODULATOR
1 Vowel a/i/u/e/o Vowel select
2 Move Speed 1 — 62 The amount of time it takes to change to the selected vowel
3 Drive 0 — 127 The amount of enhancement applied
4 Output Level 0 — 127 Output level
26: 3BAND EQ
1 EQ Low Frequency 50Hz — 2.0kHz Frequency at which the EQ will boost/cut the low range
2 EQ Low Gain -12dB — +12dB Amount of gain by which the EQ will boost/cut the low range
3 EQ Mid Frequency 100Hz — 10.0kHz Frequency at which the EQ will boost/cut the low range
4 EQ Mid Gain -12dB — +12dB Amount of gain by which the EQ will boost/cut the mid range
5 EQ Mid Width 1 — 12.0 Width of the area in which the EQ will boost/cut the mid range
6 EQ High Frequency 500Hz — 16.0kHz Frequency at which the EQ will boost/cut the high range
7 EQ High Gain -12dB — +12dB Amount of gain by which the EQ will boost/cut the high range
8 Input Mode mono/stereo Mono/stereo input mode selection
27: ISOLATOR
1 On/Off SW off, on Isolator switch
2 Low Level 0 — 127 Low frequency level
3 Mid Level 0 — 127 Mid frequency level
4 High Level 0 — 127 High frequency level
5 Low Mute SW off, on Low frequency mute switch
6 Mid Mute SW off, on Mid frequency mute switch
7 High Mute SW off, on High frequency mute switch
28: HARMONIC ENHANCER
1 HPF Cutoff Freq 500Hz — 16.0kHz Frequency at which the high pass filter will cut the low range of the effect sound
2 Drive 0 — 127 Degree with which the enhancer effect will be applied
3 Mix Level 0 — 127 Level at which the effect sound will be mixed into the dry sound
29: VOICE CANCEL
1 Low Adjust 0 — 26 Adjusts the lower frequency of the midrange cancellation
2 High Adjust 0 — 26 Adjusts the upper frequency of the midrange cancellation
30: COMPRESSOR
1 Threshold -48dB — -6dB Input level at which compression begins to be applied
2 Attack 1ms — 40ms Time until when the compressor begins to take effect
3 Release 10ms — 680ms Time until the compressor effect disappears
4 Ratio 1 — 20.0 Compression ratio of the compressor
5 Output Level 0 — 127 Output level
31: COMP + DIST
1 Drive 0 — 127 Degree of distortion
2 LPF Cutoff Freq 1.0kHz — 18.0kHz, thru Frequency at which the filter will cut the high range
3 Output Level 0 — 127 Output level
4 Edge 0 — 127 Curve of distortion characteristics (127: distortion begins suddenly; 0: distortion begins gradually)
5 Attack 1ms — 40ms (Compressor) Time until when the compressor begins to take effect
6 Release 10ms — 680ms (Compressor) Time until the compressor effect disappears
7 Threshold -48dB — -6dB (Compressor) Input level at which compression begins to be applied
8 Ratio 1 — 20.0 (Compression) Compression ratio of the compressor
9 EQ Low Frequency 32Hz — 2.0kHz Frequency at which the EQ will boost/cut the low range
10 EQ Low Gain -12dB — +12dB Gain with which the EQ will boost/cut the low range
11 EQ Mid Frequency 100Hz — 10.0kHz Frequency at which the EQ will boost/cut the mid range
12 EQ Mid Gain -12dB — +12dB Gain with which the EQ will boost/cut the mid range
13 EQ Mid Width 1 — 12.0 Width of the mid range area which the EQ will boost/cut
14 Dry/Wet Balance D63>W — D=W — D<W63 Balance of the dry sound and effect sound
32: COMP + DIST + DELAY, 33: COMP + OVERDRIVE + DELAY
1 Comp Threshold -48dB — -6dB Input level at which compression begins to be applied
2 Comp Ratio 1 — 20.0 Compression ratio of the compressor
3 Comp Attack 1ms — 40ms Time until when the compressor begins to take effect
4 Comp Release 10ms — 680ms Time until the compressor effect disappears
5 Dist. Drive 0 — 127 Degree of distortion
6 Dist Output Level 0 — 127 Output level
7 Dist EQ Low Gain -12dB — +12dB Gain with which the EQ will boost/cut the low range
8 Dist EQ Mid Gain -12dB — +12dB Gain with which the EQ will boost/cut the mid range
9 Delay Mix 0 — 127 Delay level
10 Delay Time 0.1ms — 1480.0ms Delay time
11 Dly Feedback Level -63 — +63 Amount of feedback
12 Dry/Wet Balance D63>W — D=W — D<W63 Balance of the dry sound and effect sound