User Manual

Precautions for use
AG06MK2/AG03MK2 Safety Guide
4
EN
Handling
• Do not drop a foreign object, such as a piece of metal
or paper, into any gap on this product.
Otherwise, fire, electrical shock or damage to the
product may be caused.
• Do not apply the following excessive force to this
product.
- Resting your weight on this product
- Placing heavy objects on this product
- Stacking up this product
- Applying excessive force to the buttons, switches, or
I/O connectors
Otherwise, injury or damage to the product may be
caused.
• Do not pull connected cables.
Otherwise, the product may fall or tip over, resulting
in injuries or damage to the product.
Precautions for use
NOTICE
Follow the precautions below to avoid malfunction and
damage to this product and to prevent the loss of data.
Power supply
• If you plan not to use this product for a long period of
time, disconnect the USB cable from this product.
Even when the [P] (Standby/On) switch is turned off,
a small amount of current still flows through this
product.
• Never insert or remove a USB cable with wet hands.
Installation
• Depending on the environment in which you use the
product, a phone, radio or TV may generate noise. In
that case, change the product location or orientation,
or the surrounding environment.
• Do not install this product in a place subject to:
- Extremely high or low temperatures
- Excessive dust
Otherwise, malfunction or damage to the product
may be caused.
• Do not install this product in a place where
condensation can form due to rapid, drastic changes
in ambient temperature. Using the product while
condensation is present may cause damage to the
product. If there is a reason to believe that
condensation might have occurred on or in this
product, leave it for several hours without turning on
the power. You can start using the product when the
condensation has completely dried.
Handling
• Do not place any vinyl, plastic or rubber products on
this product. Otherwise, the panel may be discolored
or deteriorate.
• Avoid setting all equalizer controls and volume to
their maximum. Depending on the condition of the
connected devices, doing so may cause feedback and
may damage the speakers.
• Do not apply oil, grease, or contact cleaner to the
faders or knobs. Doing so might cause problems with
electrical contact or fader and knobs motion.
Maintenance
• Use a dry, soft cloth to clean this product. Do not use
benzine, thinner, detergent or chemical rag to clean
the surface of the product. Otherwise, the surface
may be discolored or deteriorate.
 [USB 2.0] and [5V DC] terminals
When connecting the computer to the [USB 2.0]
connector, make sure to observe the following points.
Failing to do so risks freezing the computer and
corrupting or losing the data. If the computer or the
mixer freezes, restart the application software or the
computer OS, or turn the mixer’s [P] (Standby/On)
switch to standby and then on again.
• Be sure to use the included USB cable.
• Before connecting the computer to the [USB 2.0]
terminal, exit from any power-saving mode of the
computer (such as suspend, sleep, standby).
• Turn the [P] switch to standby before connecting
cables to the [USB 2.0] and [5V DC] terminals.
• Be sure to quit any open applications and turn the
[P] switch to standby before unplugging cables from
the [USB 2.0] and [5V DC] terminals.
• Wait for six seconds or more whenever turning the
mixer’s [P] switch from standby to on or from on to
standby.
 Connectors
XLR-type connectors are wired as follows (IEC60268
standard): pin 1: ground, pin 2: hot (+), and pin 3: cold
(-).
 Phantom Power
Be sure to leave this switch off (N) if you do not need
phantom power.
Follow the important precautions below, in order to
prevent noise and possible damage to external devices
as well as the mixer if you turn this switch on (O).